Diode-pumped continuous-wave and passively Q-switched 1.06 μm YVO4/Nd:GdVO4 laser

In this letter, a diode-pumped continuous-wave and passively Q-switched 1.06 μm laser with a novel composite YVO₄/Nd:GdVO₄ crystal was demonstrated for the first time. Theoretical calculations showed that the temperature distribution in YVO₄/Nd:GdVO₄ crystal was lower than that in GdVO₄/Nd:GdVO₄ and Nd:GdVO₄ crystals under the same conditions. After optimizing the mode matching degree, a CW output power of 5.6 W of YVO₄/Nd:GdVO₄ laser was obtained at the incident pump power of 12 W when the output coupler with transmission of 30% was employed. Using Cr^4 +:YAG crystals with initial transmission (T₀) of 80% and 90% as saturable absorbers, the pulsed YVO₄/Nd:GdVO₄ laser characteristics were investigated. At the incident pump power of 12 W, the maximum average output power of 2.76 W and the maximum repetition rate of 189 kHz was achieved when T₀ = 90% Cr^4 +:YAG was used. The shortest pulse width was 28.1 ns when the initial transmission of the used Cr^4 +:YAG was 80%.     

Growth and characterization of pure and doped bis thiourea zinc acetate: Semiorganic nonlinear optical single crystals

Metal–organic coordination complex single crystals bis thiourea zinc acetate (BTZA) and Cd²⁺ doped BTZA have been synthesized and grown successfully by slow-cooling technique from their aqueous solutions. Single crystals of pure and Cd²⁺ doped BTZA with dimensions of 35 × 4 × 2 mm³ and 10 × 5 × 6 mm³, respectively were obtained with well defined morphology. The as grown single crystals are characterized by single crystal XRD studies and melting point measurements which reveal the incorporation of metallic dopants has not changed the structure of the parent crystal. The powder X-ray diffractogram of the grown crystals has been recorded and the various planes of reflection identified shows shift in the peak positions. The metal coordination with thiourea through sulphur in pure and Cd²⁺ doped BTZA were ascertained by FTIR studies and optical absorption study to identify the UV cut-off range. The presence of metals in pure and Cd²⁺ doped BTZA crystal lattice were confirmed by atomic absorption spectroscopy (AAS). The thermal decomposition of pure and Cd²⁺ doped BTZA crystals were investigated by thermo gravimetric analyses (TGA) and differential thermal analysis (DTA) indicate that doped crystals are more stable than pure crystals. The dielectric response of the crystals were studied in the frequency range 100 Hz–5 MHz at different temperatures and the results are discussed. Second harmonic generation (SHG) measurement confirms that the pure and Cd²⁺ doped BTZA have nonlinear optical (NLO) property. Laser damage threshold value of 12.44 MW/cm² has been determined using Q-switched Nd:YAG laser operating at 1064 nm and with 8 ns pulses in single shot mode for pure BTZA single crystal is reported for the first time.     

Passively Q-switched diode-pumped Raman laser with third-order Stokes eye-safe oscillation

We demonstrate a passively Q-switched all-solid-state laser system with intracavity Raman frequency conversion to the eye-safe spectral region. Laser oscillation at the 1.064 μm wavelength with a pulse repetition rate of several kilohertz was provided by a Nd:YAG crystal and a Cr:YAG passive absorber. Third Stokes oscillations at the 1.599 and 1.494 μm wavelengths were obtained in Ba(NO₃)₂ and PbWO₄ crystals with output pulse energies of 5 μJ and 6 μJ, respectively. The results of the numerical simulation of the pulse dynamics are in good agreement with the experimental data.     

Effect of Co2+ on the growth,optical properties and laser damage threshold of potential nonlinear optical l-alanine single crystal

Good transparent bulk single crystals of pure l-alanine (LA) and cobalt doped LA crystals have been synthesized and successfully grown by slow-cooling method from their aqueous solutions. The concentration of metal dopants in the mother solution with 0.5 mol% for cobalt was carried out individually and crystals were obtained with well defined morphology. The as grown metal doped and pure single crystals were characterized by single crystal XRD studies which confirm that the incorporation of metallic dopants has not changed the basic structure of the parent crystal. The absorption of these crystals was analyzed and the result confirms that they possess low absorption in the range 230–1100 nm. Fourier transform infrared (FTIR) spectroscopy was carried out to investigate the molecular vibrations of these crystals and to confirm the incorporation of the dopants. The thermal properties have been studied by TGA/DTA curves. The EDAX measurement and surface morphology were studied for pure and metal doped LA crystals. The second harmonic generation (SHG) signals were observed using Nd: YAG laser with fundamental wavelength of 1064 nm in pure and metal doped crystals. The laser damage threshold was measured for pure and metal doped LA crystals and also tested by using a Q-switched Nd: YAG laser showed enhanced LDT value for metal (Co²⁺) doped LA crystal compared to pure LA crystal due to the metallic substitutions thus proving their useful candidature for nonlinear optical applications.     

Hyperpolarizability and two photon observation of imidazolium picrate

The computational calculation based on the density functional theory at the basis sets level has been employed to compute the first-order hyperpolarizability of the title material. The nonlinear optical properties of imidazolium picrate was assessed by a open aperture z-scan technique in which Nd:YAG laser pulse at 532 nm wavelength was used as excitation source. Laser damage threshold of the crystal was investigated with Nd:YAG assembly for multiple shots and reported. The changes were observed and analyzed on (0 1 1) and (0 0 1) planes.     

Diode-pumped Nd:YAG ceramic laser at 946 nm passively Q-switched with a Cr4+:YAG saturable absorber

We demonstrate a diode-pumped Nd:YAG ceramic laser with emission at 946 nm that is passively Q-switched by single-crystal Cr⁴⁺:YAG saturable absorber. An average output power of 1.7 W is measured under 18.4 W of incident power using an output mirror with transmission T=4%. The corresponding optical-to-optical efficiency is 9.2%. The laser runs at a pulse repetition rate of 120 kHz and delivers pulses with energy of 14 μJ and duration of 80 ns, which corresponds to a peak power of 175 W.     

YAG laser-induced β-BaB2O4 crystalline dot formation in Sm2O3–BaO–B2O3 glasses

A continuous-wave (CW) YAG laser (power: 0.75–0.9 J/s, irradiation time: 15 s–15 min) with a wavelength of 1064 nm is irradiated to 11.1Sm₂O₃·44.4BaO·44.4B₂O₃ glass, and the formation of β-BaB₂O₄ (β-BBO) crystalline dots with a diameter of 30–150 μm is confirmed from micro-Raman spectra. β-BBO crystals with around 200 μm length grow towards the interior of the glass. The incorporation of Sm³⁺ into β-BBO crystalline dots is suggested from micro-Raman and fluorescence spectra. The second harmonic generation is detected from the array (10×10=100 dots) of β-BBO crystalline dots, indicating that each crystalline dot formed by YAG laser irradiation is a nonlinear optical crystal. CW YAG laser irradiation to glass with Sm³⁺ ions is a nice technique for a spatially controlled crystal growth.     

Doubly Q-switched GdVO4/Nd:GdVO4 laser with AO modulator and Cr4+:YAG saturable absorber under direct 879 nm diode pumping to the emitting level

In this letter, a doubly Q-switched 1.06 μm pulse laser with AO modulator and Cr⁴⁺:YAG saturable absorber by direct pumping grown-together composite GdVO₄/Nd:GdVO₄ crystal is demonstrated for the first time. Compared to purely AO Q-switching, the simultaneous use of AO Q-switch and Cr⁴⁺:YAG saturable absorber can generate shorter pulses and more symmetric temporal profiles. The thermal lens effect of laser crystal was analyzed.     

High power Nd:YAG lasers operating at 1.3 μm wave band

The laser properties of 1.3 μm spectral region in Nd:YAG crystal and their simultaneous dual wavelength threshold condition are investigated. Three types of high power 1.3-μm Nd:YAG quasi continuous wave (QCW) lasers, which operate at 1.319 μm or 1.338 μm single wavelength, 1.319 μm and 1.338 μm simultaneous dual wavelength, are achieved with a maximum average output power of 138 W, 132 W and 120 W, respectively.     

Passively Q-switched a-cut Nd:GdVO4 self-Raman laser with Cr:YAG

A passively Q-switched a-cut Nd:GdVO₄ self-Raman solid-state laser with Cr:YAG saturable absorber was firstly demonstrated. The first Stokes at 1173 nm was successfully obtained. At the maximum incident pump power, the pulse width was about 1.8 ns and the repetition rate was 27.5 kHz. 586.5 nm yellow laser output was also realized by use of an LBO frequency doubling crystal.     

LD-end-pumped passively Q-switched Nd:YAG ceramic laser with single wall carbon nanotube saturable absorber

We report on a LD-end-pumped passively Q-switched Nd:YAG ceramic laser by using a novel single wall carbon nanotube saturable absorber (SWCNT-SA). The SWCNT wafer was fabricated by electric Arc discharge method on quartz substrate with absorption wavelength of 1064 nm. We firstly investigated the continuous wave (CW) laser performance and scattering properties of Nd:YAG ceramic sample. For the case of passively Q-switched operation, a maximum output power of 376 mW was obtained at an incident pump power of 8.68 W at 808 nm, corresponding to an optical–optical conversion efficiency of 4.3%. The repetition rate as the increase of pump power varied from 14 to 95 kHz. The minimum pulse duration of 1.2 μs and maximum pulse energy of 4.5 μJ was generated at a repetition rate of 31.8 kHz.     

Influence of the nanoparticle sizes on the photo-induced absorption of La–Ga–S–O–Dy glass nanocomposites

We have established that the illumination by two coherent beams originating from nanosecond Nd:YAG laser at wavelengths 1064 nm and 532 nm in the La–Ga–S–O–Gd:PVA La-Ga-S-O-Dy polymer glass nanocomposites leads to substantial changes in the absorption. The effect is completely reversible and disappears after interruption of the optical treatment. The illumination power density was varied up to 0.6 GW/cm². All the samples show destruction less than 0.2% changes after more than 300,000 laser pulses. The beams were incident with the angles varying between 45° and 50° with respect to the nanocomposite surface. Moreover, the additional analysis of TEM did not demonstrate any additional aggregations. The role of light polarizations, beam stability, and light scattering is discussed.     

Design and construction of Q-switched Nd:YAG laser system for LIBS measurements

A passive, Q-switched pulsed, Nd:YAG laser system was designed and built, which can provide a potential compact robust laser source for portable laser induced breakdown spectroscopy systems.The developed laser system operates at 1064 nm. Each laser shot contains a train of pulses having maximum total output energy of 170 mJ. The number of pulses varies from 1–6 pulses in each laser shot depending on the pump energy. The pulse width of each pulse ranges from 20 to 30 ns. The total duration of the output pulse train is within 300 μs. The multi-pulse nature of the laser shots was employed to enhance the LIBS signal. To validate the system, LIBS measurements and analysis were performed on ancient ceramic samples collected from Al-Fustat excavation in Old Cairo. The samples belong to different Islamic periods in Egypt history. The results obtained are highly indicative that useful information can be provided to archeologists for use in restoring and repairing of precious archeological objects.     

Improvement in solar-pumped Nd:YAG laser beam brightness

Solar-pumped solid-state lasers are promising for renewable extreme-temperature material processing. Here we report a large improvement in solar laser beam brightness by pumping a thin Nd:YAG single crystal rod. A fused silica light guide of 14 mm×22 mm rectangular cross-section is used to both transmit and homogenize the concentrated solar radiation from the focal zone of a 2.88 m² parabolic mirror to the entrance aperture of a modified 2D-CPC flooded pump cavity, within which a 4 mm diameter rod is efficiently pumped. 2.2% slope efficiency is reached. Laser beam brightness figure of merit B is three times higher than that of the most recent solar-pumped Nd:YAG laser by a Fresnel lens. The introduction of the rectangular cross-section light guide has also ensured a much more stable laser emission than previous pumping schemes.     

Influence of the ZnO nanoparticle sizes and morphology on the photoinduced light reflectivity

We have established a principal possibility of changes of the light reflectivity at the wavelength of 633 nm (He–Ne laser) under influence of the external laser light. The changes are very sensitive to the wavelength of the photoinduced laser. We have chosen two types of the photoinduced lasers: UV nitrogen 7 ns laser at wavelength 371 nm heating near the absorption edge and the 10 ns 1064 nm Nd:YAG laser with wavelength 1064 nm. The power dependences of the reflectivity were studied. Possible explanation of the observed effects is presented following the conception of the nano-trapping levels. These results have been obtained from two ZnO thin films prepared from principally different deposition parameters leading to different particle features and morphologies.     

High efficiency diode-pumped slab oscillator and amplifier for space-based application

The design and performance of conduction-cooled, laser diode-pumped oscillator and amplifier slab laser featuring high efficiency, high pulse energy and high beam quality for space-based application are reported. The oscillator was a diode-pumped Q-Switched Nd:YAG slab laser using unstable resonator, and the amplifiers were two zig-zag Nd:YAG slabs based on a side-pumped slab geometry. A near diffraction-limited output of 450 mJ in a 10 ns pulse at a repetition rate of 20 Hz was obtained, corresponding to an optical-to-optical conversion efficiency of over 20%.     

Growth and characterization of Nd:Bi12SiO20 single crystal

A Nd:Bi₁₂SiO₂₀ crystal was grown by the Czochralski method. The thermal properties of the crystal were systematically studied. The thermal expansion coefficient was measured to be α=11.42×10^?6 K^?1 over the temperature range of 295–775 K, and the specific heat and thermal diffusion coefficient were measured to be 0.243 Jg^?1 k^?1 and 0.584 mm²/s, respectively at 302 K. The density was measured to be 9.361 g/cm³ by the buoyancy method. The thermal conductivity of Nd:Bi₁₂SiO₂₀ was calculated to be 1.328 Wm^?1 K^?1 at room temperature (302 K). The refractive index of Nd:Bi₁₂SiO₂₀ was measured at room temperature at eight different wavelengths. The absorption and emission spectra were also measured at room temperature. Continuous-wave (CW) laser output of a Nd:Bi₁₂SiO₂₀ crystal pumped by a laser diode (LD) at 1071.5 nm was achieved with an output power of 65 mW. To our knowledge, this is the first time LD pumped laser output in this crystal has been obtained. These results show that Nd:Bi₁₂SiO₂₀ can serve as a laser crystal.     

60 W yellow laser at 561 nm by intracavity frequency doubling of a diode-pumped Q-switched Nd:YAG laser

A high-power yellow laser was achieved by intracavity frequency doubling of a diode-pumped Nd:YAG rod laser. A solid etalon was inserted into the resonator to implement efficient operation of the low-gain single line at 1123 nm transition. By using a LBO crystal inside the cavity as the frequency doubler, the maximum output power of the 561 nm yellow laser was obtained to be as high as 60.3 W with a pulse repetition frequency of 6 kHz, corresponding to an optical-to-optical conversion efficiency of about 6.1%. The output power fluctuation of the yellow laser was measured to be better than 3% in half an hour.     

Dual-wavelength investigation of laser-induced damage in multilayer mirrors at 532 and 1064 nm

Thin film beam splitters with high reflectivity at 532 nm and high transmittance at 1064 nm were deposited via reactive electron-beam evaporation with optimized parameters. The damage performance of the samples was investigated under irradiations of 532 nm laser only, 1064 nm laser only, and various combined laser fluences. The damages induced by the 1064 nm laser were primarily attributed to the initiators at the interface between the coatings and substrate. Under 532 nm laser irradiation only, two distinctive damage pits initiated by the submicron absorptive defects located at different coating depths and correlated to interfaces were observed. The damage effect under simultaneous irradiation in multilayer films was also investigated. The respective sensitive defects of the two lasers remained the precursors for causing damage. However, the dominant damage factors in simultaneous irradiation changed with the 1064 nm laser fluence, which also determined the coupling effect between the two lasers in terms of causing damage. Finally, correlative analysis methods were used to discuss the different coupling effects.     

Optical spectroscopy in channel waveguides made in Nd:YAG crystals by femtosecond laser writing

In this work, we present an optical characterization of channel waveguides fabricated by means of femtosecond laser writing on Nd:YAG substrates. These guiding structures show a refractive index increment of about 1×10^?3 which allows TE propagation. By pumping with a CW solid-state laser at 532 nm reaching the ²G_9/2 and ⁴G_7/2 manifolds of Nd³⁺ ions, we have explored the emission band corresponding to ⁴F_3/2→⁴I_9/2 optical transitions (peaked at 890 nm). From data, we have found that emission showed similar characteristics for waveguide and bulk. On the other hand, the lifetime corresponding to the ⁴F_3/2 metaestable level was determined to be 240 μs for bulk and waveguide. Summarizing, we have made suitable channel waveguides in Nd:YAG crystals, by fs interaction, with similar spectroscopic properties to those of the bulk, a fact that boosters the photonics application of these devices. For the first time to our knowledge, a direct index increment waveguide made by interaction with ultra-short intense pulses in YAG crystals has been performed. This fabrication procedure can be an efficient tool to make several optical circuits in active materials by means of the one-step, fast and low-cost processing.