An electrochemical investigation of Li intercalation in the sol-gel LiMn2O4 spinel oxide

An alternative approach for obtaining the LiMn₂O₄ spinel phase is provided by the use of the sol-gel method in aqueous solution. The main electrochemical properties of the sol-gel LiMn₂O₄ phase are reported. In addition to chronopotentiometric and voltammetric experiments, the kinetics of the electrochemical insertion–extraction of lithium in Li_xMn₂O₄ (0.25<x<1) has been investigated using ac impedance spectroscopy. The strong variation of the chemical diffusion coefficient D_Li vs x, in the range 10⁻⁸–10⁻¹¹ cm² s⁻¹ (D_Li is found to be maximum for x=0.55) is critically discussed.     

Improvement of electrochemical performance of all-solid-state lithium secondary batteries by surface modification of LiMn2O4 positive electrode

To improve the electrochemical performance of an all-solid-state In/80Li₂S⋅20P₂S₅ (electrolyte)/LiMn₂O₄ cell, a lithium-titanate thin film was used to coat LiMn₂O₄. The interfacial resistance between LiMn₂O₄ and the electrolyte (measured after initial charging) decreased when the LiMn₂O₄ particles were coated with lithium-titanate. A cell with lithium-titanate-coated LiMn₂O₄ had a higher capacity than a cell with noncoated LiMn₂O₄ for current densities in the range 0.064 to 2.6 mA cm^− 2. Additionally, a cell with coated LiMn₂O₄ retained 96% of the 10th-cycle reversible capacity at a current density of 0.064 mA cm^− 2 after 50 cycles.     

Surface modification of LiMn2O4 thin films at elevated temperature

In order to improve the cycle stability of spinel LiMn₂O₄ electrode at elevated temperature, the LiCoO₂-coated and Co-doped LiMn₂O₄ film were prepared by an electrostatic spray deposition (ESD) technique. LiCoO₂-coated LiMn₂O₄ film shows excellent cycling stability at 55 °C compared to pristine and Co-doped LiMn₂O₄ films. The samples were studied by X-ray diffraction, scanning electron microscopy, Auger electron spectroscopy, cyclic voltammetry and electrochemical impedance spectroscopy. The excellent performance of LiCoO₂-coated LiMn₂O₄ film can be explained by suppression of Mn dissolution. On the other hand, the LiCoO₂-layer on the LiMn₂O₄ surface allows a homogenous Li⁺ insertion/extraction during electrochemical cycles and improves its structure stability.     

Characterization and electrochemical performance of the spinel LiMn2O4 prepared from -MnO2

The preparation and characterization of the spinel LiMn₂O₄ obtained by solid state reaction from quasi-amorphous -MnO₂ is reported. A well-defined highly pure spinel was characterized from X-ray diffractograms. The average manganese valence of -MnO₂ and spinel samples was found to be 3.89±0.01 and 3.59±0.01, respectively. The electrochemical performance of the spinel was evaluated through cyclic voltammetry and chronopotentiometry. The voltammetric profiles obtained at 1 mV/s for the LiMn₂O₄ electrode in 1 M LiClO₄ dissolved in a 2:1 mixture of ethylene carbonate and dimethyl carbonate showed typical peaks for the lithium insertion/extraction reactions. The charge capacity of this electrode was found to be 110 mA h g⁻¹ for the first charge/discharge cycles.     

Al掺杂的尖晶石型LiMn2O4的结构和电子性质

采用基于密度泛函理论的第一性原理方法, 在广义梯度近似(GGA)和GGA+U方法下对尖晶石型LiMn₂O₄及其Al掺杂 的尖晶石型LiAl_0.125Mn_1.875O₄晶体的结构和电子性质进行了计算. 结果表明: 采用GGA方法得到尖晶石型LiMn₂O₄是立方晶系结构, 其中的Mn离子为+3.5价, 无法解释它的Jahn-Teller 畸变. 给出的LiMn₂O₄能带结构特征也与实验结果不符. 而采用GGA+U方法得到在低温下的LiMn₂O₄和其掺杂 体系LiAl_0.125Mn_1.875O₄的晶体都是正交结构, 与实验一致. 也能明确地确定Mn的两种价态Mn³⁺/Mn⁴⁺的分布并且能够说明Mn³⁺O₆的z方向有明显的Jahn-Teller 畸变, 而Mn⁴⁺O₆则没有畸变. LiMn₂O₄的能带结构与实验比较也能够符合. 采用GGA+U方法对Al掺杂体系的LiAl_0.125Mn_1.875O₄的研究表明, 用Al替换一个Mn不会明显地改变晶体的电子性质, 但可以有效地消除Al³⁺O₆ 八面体的Jahn-Teller畸变, 从而改善正极材料LiMn₂O₄的性能, 这与电化学实验的观察结果相一致.     

Preparation of LiMn2O4 thin films by a sol–gel method

LiMn₂O₄ thin films were prepared by a sol–gel method using spin-coating and annealing processes. Anhydrous Mn(CH₃COCHCOCH₃)₃ (manganese acetylacetonate) and LiCH₃COCHCO–CH₃ (lithium acetylacetonate) were chosen as source materials. The film electrochemical properties depended on the drying temperature even when subjected to the same annealing conditions. The discharge capacity of annealed film increased as the drying temperature was increased. However, the rate of capacity fading during cycling increased as the drying temperature was increased.     

Physical properties of the cubic spinel LiMn2O4

We have performed an ab initio study of structural, electronic, magnetic, vibrational and thermal properties of the cubic spinel LiMn₂O₄ by employing the density functional theory, the linear-response formalism, and the plane-wave pseudopotential method. An analysis of the electronic structure with the help of electronic density of states shows that the density of states at the Fermi level (N (E_F)) is found to be governed by the Mn 3d electrons with some contributions from the 2p states of O atoms. It is important to note that the contribution of Mn 3d states to N(_EF)$N\left(E_F\right)$ is as much as 85%. From our phonon calculations, we have obtained that the main contribution to phonon density of states (below 250 cm⁻¹) comes from the coupled motion of Mn and O atoms while phonon modes between 250 cm⁻¹ and 375 cm⁻¹ are characterized by the vibrations of all the three types of atoms. The contribution from Li increases rapidly at higher frequency (above 375 cm⁻¹) due to the light mass of this atom. Finally, the specific heat and the Debye temperature at 300 K are calculated to be 249.29 J/mol K and 820.80 K respectively.     

Kinetic aspects of Li intercalation in mechano-chemically processed cathode materials for lithium ion batteries: Electrochemical characterization of ball-milled LiMn2O4

Micrometric LiMn₂O₄ particles are mechano-chemically modified by ball-milling to obtain a mixture of nano- and micro-scale particles. This mixture is tested as a potential active cathode material for rapid-charge Li ion batteries, and also as a model system for studying the detailed kinetics of Li intercalation/de-intercalation in such electrodes. Ragone plots recorded using galvanostatic measurements indicate enhanced power delivery characteristics of the ball-milled LiMn₂O₄ compared to its unprocessed counterpart. The processed material also exhibits improved resistance against electrolyte reactions and surface film formation. Due to these advantageous electrochemical attributes, the ball-milled LiMn₂O₄ serves as an adequately suited system for exploring certain fundamental aspects of Li intercalation in this material. Scan rate dependent slow scan cyclic voltammetry helps to identify the kinetic and diffusion controlled features of Li transport in mechano-chemically processed LiMn₂O₄. Electrochemical impedance spectroscopy substantiates these findings further and provides detailed kinetic parameters, including voltage dependent charge transfer resistance and diffusion coefficient of Li transport.     

The effect of doping LiMn2O4 spinel on its use as a cathode in Li-ion batteries: neutron diffraction and electrochemical studies

A series of compounds Li_1+yMn_2−xM′_xO₄ (x≤0.1;y≤0.02), have been synthesised by doping the parent LiMn₂O₄ spinel with various metal ions of variable oxidation state. Powder neutron diffraction data has been collected on these samples alongside a series of electrochemical experiments in order to elucidate the relationship between structure on the performance of these systems as Li batteries. Doping the LiMn₂O₄ spinel with a small amount of metal ions has a remarkable effect on the electrochemical properties. Whereas the capacity of the spinels doped with trivalent ions is much greater, the cycling fading properties are much enhanced with using divalent ions as dopants. The underlying reasons for this are discussed, and it is suggested that the occupancy of the tetrahedral site with divalent ions to form a more compact structure offers an improved structural stability to support greater Li insertion/extraction, but which ultimately prevents the free movement of Li also sited on the tetrahedral site of the lattice.     

Ordered fluorite phases in the Bi2O3-Ta2O5 system: A structural and electrical investigation

Structure and electrical behaviour are reported for the system Bi_1-xTa_xO_1.5 + x (0.167 ≤ x ≤ 0.250). In the compositional range 0.200 < x ≤ 0.250 an incommensurately modulated pseudo-cubic phase (type II) is observed, with the appearance of a larger pseudo-cubic phase in the region 0.167 ≤ x ≤ 0.200. Structural analysis of the type II phases by neutron diffraction reveals subtle changes in the oxide ion distribution with temperature, associated with changes in the incommensurate modulation parameter. Analysis of the defect structure of the type II phase reveals chains of tantalate octahedra as a likely structural motif. It is proposed that these chains facilitate an electronic contribution to total conductivity at low temperatures through electron hopping along the chains. Changes in oxide ion vacancy ordering may explain the observed non-linear behaviour in the thermal expansion of lattice parameter and Arrhenius plots of total conductivity.     

Ground-state magnetism of chromium-substituted LiMn2O4 spinel

Comparative crystal structure and magnetic properties studies have been conducted on quaternary powder spinel samples LiMn_1.82Cr_0.18O₄ obtained by two different synthesis methods, glycine-nitrate (GN) and ultrasonic spray-pyrolysis (SP). Although both samples possess the same spinel structure of the cubic space group Fd3¯m, their low-temperature magnetic properties display significant differences. While the SP sample undergoes only spin-glass transition at the freezing temperature T_f=20 K, the GN sample possesses more complicated low-temperature magnetic behavior of the reentrant spin-glass type with the Néel temperature T_N=42 K and freezing temperature T_f=22 K. High-temperature magnetic susceptibility of both samples is of the Curie–Weiss type with the effective magnetic moments in agreement with the nominal compositions. This fact together with the results of the chemical analysis discards the existence of the diversity in chemical compositions as a possible cause for the observed differences in the low-temperature magnetism. On the other hand, the crystal structure analysis done by the Rietveld refinement of the X-ray powder diffraction data points to the strong influence of the cation distribution on the ground-state magnetism of these systems. An explanation of this influence is proposed within the framework of a collective Jahn–Teller effect.     

Structural and electrochemical properties of Nd-doped LiFePO4/C prepared without using inert gas

To further improve the electrochemical performance of LiFePO₄/C, Nd doping has been adopted for cathode material of the lithium ion batteries. The Nd-doped LiFePO₄/C cathode was synthesized by a novel solid-state reaction method at 750 °C without using inert gas. The Li_0.99Nd_0.01FePO₄/C composite has been systematically characterized by X-ray diffraction, EDS, SEM, TEM, charge/discharge test, electrochemical impedance spectroscopy and cyclic stability. The results indicate that the prepared sample has olivine structure and the Nd³⁺ and carbon modification do not affect the structure of the sample but improve its kinetics in terms of discharge capacity and rate capability. The Li_0.99Nd_0.01FePO₄/C powder exhibited a specific initial discharge capacity of about 161 mAh g^− 1 at 0.1 C rate, as compared to 143 mAh g^− 1 of LiFePO₄/C. At a high rate of 2 C, the discharge capacity of Li_0.99Nd_0.01FePO₄/C still attained to 115 mAh g^− 1 at the end of 20 cycles. EIS results indicate that the charge transfer resistance of LiFePO₄/C decreases greatly after Nd doping.     

High pressure Raman spectroscopic study of spinel MgCr2O4

An in situ Raman spectroscopic study was conducted to investigate the pressure induced phase transformation of MgCr₂O₄ spinel up to pressures of 76.4 GPa. Results indicate that MgCr₂O₄ spinel undergoes a phase transformation to the CaFe₂O₄ (or CaTi₂O₄) structure at 14.2 GPa, and this transition is complete at 30.1 GPa. The coexistence of two phases over a wide range of pressure implies a sluggish transition mechanism. No evidence was observed to support the pressure-induced dissociation of MgCr₂O₄ at 5.7-18.8 GPa, predicted by the theoretical simulation. This high pressure MgCr₂O₄ polymorphism remains stable upon release of pressure, but at ambient conditions, it transforms to the spinel phase.     

Electrical and electrochemical properties of glass-ceramic electrolytes in the systems Li2S-P2S5-P2S3 and Li2S-P2S5-P2O5

Electrical and electrochemical properties of the 70Li₂S·(30 − x)P₂S₅·xP₂S₃ and the 70Li₂S·(30 − x)P₂S₅·xP₂O₅ (mol%) glass-ceramics prepared by the mechanical milling technique were investigated. Glass-ceramics with 1 mol% P₂S₃ and 3 mol% P₂O₅ showed the highest conductivity of 5.4 × 10^− 3 S cm^− 1 and 4.6 × 10^− 3 S cm^− 1, respectively. Moreover, these glass-ceramics showed higher electrochemical stability than the 70Li₂S·30P₂S₅ (mol%) glass-ceramic. From the XRD patterns of the obtained glass-ceramics, trivalent phosphorus and oxygen were incorporated into the Li₇P₃S₁₁ crystal. We therefore presume that the Li₇P₃S₁₁ analogous crystals, which were formed by incorporating trivalent phosphorus and oxygen into the Li₇P₃S₁₁ crystal, improve the electrical and electrochemical properties of the glass-ceramics. An all-solid-state cell using the 70Li₂S·29P₂S₅·1P₂S₃ (mol%) glass-ceramic as solid electrolyte operated under the high current density of 12.7 mA cm^− 2 at the high temperature of 100 °C. The cell showed an excellent cyclability of over 700 cycles without capacity loss.     

Electron energy-loss spectroscopy of LiMn2O4, LiMn1.6Ti0.4O4 and LiMn1.5Ni0.5O4

The dielectric properties of LiMn₂O₄, LiMn_1.6Ti_0.4O₄ and LiMn_1.5Ni_0.5O₄ powders, synthesized by sol-gel method, were determined by analyzing the low-loss region of the electron energy-loss spectroscopy (EELS) spectrum in a transmission electron microscope. From these data, the optical joint density of states (OJDS) was obtained by Kramers-Kronig analysis. Since maxima observed in the OJDS spectra are assigned to interband transitions above the Fermi level, these spectra can be interpreted on the basis of calculated density of states (DOS), carried out with the CASTEP code. Experimental and theoretical results are in good agreement.     

The effect of cation doping on spinel LiMn2O4: a first-principles investigation

The effect of the cation doping on the electronic structure of spinel LiM_yMn_2−yO₄ (M=Cr, Mn, Fe, Co and Ni) has been calculated by first-principles. Our calculation shows that new M-3d bands emerge in the density of states compared with that in LiMn₂O₄. Simultaneously, the new O-2p bands appear accordingly in almost the same energy range around the Fermi energy owing to the M-3d/O-2p interaction. It is found that the appearance of new O-2p bands in the lower energy position results in a higher intercalation voltage. Consequently, the origin of higher intercalation voltage in LiM_yMn_2−yO₄ can be ascribed to the lower O-2p level introduced by the doping cation M.     

Lithium extraction/insertion from LiMn2O4 — effect of crystallinity

Effect of host crystallinity on lithium extraction/insertion of LiMn₂O₄ was studied. LiMn₂O₄ powders with different crystallinity were prepared via lithium-manganese-tartrates by heat treatment at various temperatures above 300 °C. First charge-discharge capacity around 4 V depended on lattice parameter a₀ and lattice strain . On the other hand, the first discharge capacity around 3 V was found to be independent of these parameters.     

R型铁氧体BaFe4-xTi2+xO11的化学组态以及磁性行为的研究

本文通过传统的固相反应法制备了R型六角铁氧体BaFe_4-xTi_2+xO₁₁ (x= 0, 0.25, 0.5, 0.75, 1), 并且对它的原子价态以及磁性行为进行了研究. X 射线光电子能谱(XPS)结果显示了随着掺杂含量的增加, 体系中Fe³⁺离子逐渐减少而Fe²⁺离子逐渐增加. 由于具有非对称结构的阻挫晶格中存在各种关联作用的竞争, 使得BaFe_4-xTi_2+xO₁₁体系表现出了复杂的磁有序行为, 在T₁～250 K和T₂～83 K两处存在磁转变. 对这一系列掺杂样品, 在相变温度T₁之上表现顺磁行为, 而在相变温度T₂前后的磁化强度都表现出低场下随磁场的增加快速增加, 高场下则线性变化且在5×10⁴ Oe时还未达到饱和的行为, 表明这一系列掺杂样品是典型的倾斜反铁磁态(canted antiferromagnetic) 或者亚铁磁态.     

Spin-glass-like ordering in the spinel ZnFe2O4 ferrite

In the present study, spin-glass-like ordering has been observed in the spinel ZnFe₂O₄ ferrite. Field cooled (FC) and zero-field cooled (ZFC) DC magnetizations display divergence at low temperature, which indicates a frozen state with the freezing temperature of T_f=21 K. Frequency dependence of AC susceptibility measurement was performed on the sample. It shows a peak at around T_f, with the peak position shifting as a function of driving frequency, indicating a spin-glass-like transition of the sample. The sample shows a typical spin-glass behavior with a manifestation of non-equilibrium dynamics of the spin glass, such as aging, rejuvenation and memory effects. These experimental findings indicate that Zn-ferrite exhibits a spin-glass-like phase at low temperature and it is not canted antiferromagnetic.     

Direct micron-sized LiMn2O4 particle coating on LiCoO2 cathode material using surfactant

Micron-sized LiMn₂O₄ particles were easily coated on LiCoO₂ cathodes using an amphoteric gelatin surfactant at pH4–5. The coated LiCoO₂ material showed a significantly higher thermal stability during charging and capacity retention on cycling at 4.6 V, compared to the bare LiCoO₂.