飞秒激光在6H SiC晶体表面制备纳米微结构

激光诱导周期性纳米微结构在多种材料包括电介质、半导体、金属和聚合物中观察到。研究了800nm和400nm飞秒激光垂直聚焦于6H SiC晶体表面制备纳米微结构。实验观察到800nm和400nm线偏光照射样品表面分别得到周期为150nm和80nm的干涉条纹,800nm圆偏振激光单独照射样品表面得到粒径约100nm的纳米颗粒。偏振相互垂直的800nm和400nm激光同时照射晶体得到粒径约100nm的纳米颗粒阵列,该纳米阵列的方向随400nm激光强度增加而向400nm偏振方向偏转。利用二次谐波的观点对以上纳米结构的形成给出了解释。     

Microstructure and lubricating property of ultra-fast laser pulse textured silicon carbide seals

Most previous studies have employed surface patterning to improve the performance of lubrication systems. However, few have experimentally analyzed improved effects on friction reduction in SiC mechanical seals by ultra-fast laser pulse texturing. This work applies surface texturing on a non-contact mechanical seal and analyzes the characteristics of the resultant surface morphology. A femtosecond laser system is employed to fabricate micro/nanostructures on the SiC mechanical seal, and generates microscale-depth stripes and induces nanostructures on the seal surface. This work examines the morphology and cross section of the SiC nanostructures that correspond to the different scanning speeds of the laser pulse. Results show that varying the scanning speed enables the application of nanostructures of different amplitudes and widths on the surface of the seal. The friction coefficient of the introduced SiC full-textured seal is about 20% smaller than that of a conventional SiC mechanical seal. Hence, femtosecond laser texturing is effective and enables direct fabrication of the surface micro/nanostructures of SiC seals. This technique also serves as a potential approach to lubricating applications.     

Nanostructures on SiC surface created by laser microablation

Silicon carbide (SiC), as it is well-known, is inaccessible to usual methods of technological processing. Consequently, it is important to search for alternative technologies of processing SiC, including laser processing, and to study the accompanying physical processes. The work deals with the investigation of pulsed laser radiation influence on the surface of 6H-SiC crystal. The calculated temperature profile of SiC under laser irradiation is shown. Structural changes in surface and near-surface layers of SiC were studied by atomic force microscopy images, photoluminescence, Raman spectra and field emission current-voltage characteristics of initial and irradiated surfaces. It is shown that the cone-shaped nanostructures with typical dimension of 100-200 nm height and 5-10 nm width at the edge are formed on SiC surface under nitrogen laser exposure (λ = 0.337 μm, t_p = 7 ns, E_p = 1.5 mJ). The average values of threshold energy density 〈W_thn〉 at which formation of nanostructures starts on the 0 0 0 1 and surfaces of n-type 6H-SiC(N), nitrogen concentration n_N ≅ 2 × 10¹⁸ cm⁻³, are determined to be 3.5 J/cm² and 3.0 J/cm², respectively. The field emission appeared only after laser irradiation of the surface at threshold voltage of 1000 V at currents from 0.7 μA to 0.7 mA. The main role of the thermogradient effect in the processes of mass transfer in prior to ablation stages of nanostructure formation under UV laser irradiation (LI) was determined. We ascertained that the residual tensile stresses appear on SiC surface as a result of laser microablation. The nanostructures obtained could be applied in the field of sensor and emitting extreme electronic devices.     

Theoretical and Experimental Investigation of the Formation of High Spatial Frequency Periodic Structures on Metal Surfaces Irradiated by Ultrashort Laser Pulses

Experimental results on the formation of small-scale periodic nanostructures during ablation of solids by pico- and femtosecond laser pulses are presented. The period of these nanostructures is in the range of 50 to 100 nm, and they may coexist with known periodic nanostructures, whose period and orientation is determined by the laser wavelength and amounts to several hundreds of nanometers. The formation of high-frequency periodic structures with a period of about 100nm is theoretically analyzed by joint numerical solution of the heat conduction problem and Navier?Stokes equation. It is shown that their orientation is determined by the melt bath geometry.     

飞秒激光诱导ZnO :Al薄膜周期结构及其光致发光特性

利用单束800 run飞秒激光在掺杂了Al的ZnO薄膜中制备了纳米周期条纹结构.研究了不同能流密度的飞秒激光在照射不同的时间后,表面纳米周期结构的变化规律及其形成机制.利用He-Ge激光器作为激发光源,研究了ZnO:Al薄膜的光致发光特性及其与纳米周期结构的关系.结果表明,近带隙发光增强的主要原因是800 nm飞秒激光...     

Fabrication of two types of one-dimensional Si–C nanostructures by laser ablation

Two types of one-dimensional (1D) nanostructures—amorphous silicon carbide (SiC) nanowires, 5–30 nm thick and 0.5–2 μm long, and carbon nanotubes (CNTs) filled completely with crystalline SiC nanowires, 10–60 nm thick and 2–20 μm long—were synthesized by the laser ablation of carbon-silicon targets in the presence of high-pressure Ar gas up to 0.9 MPa. All the CNTs checked by transmission electron microscopy contained SiC, and no unfilled CNTs were produced. We discuss the growth of the two nanostructures based on the formation of molten Si–C composite particles and their instabilities leading to the precipitation of Si and C.     

Carbon dendrite formation induced by pulsed laser irradiation

Porous carbon dendrite has been prepared by irradiating graphite targets with 532 nm, 10 ns laser pulses. The prepared samples were characterized by means of scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. The measurement results show that carbon dendrite structures with cluster diameter of 10 nm were obtained on the irradiated target surface in an inert gas atmosphere. The evolution of target surface morphology induced by different laser intensities was investigated. The formation mechanism of the dendrite structure has been discussed in detail. The laser intensity plays an important role in the formation of the nanostructures and there exists an optimum intensity to prepare the carbon dendrite.     

Laser Fabrication of Nanostructures on a Pure Aluminum Surface in Air

We report on the fabrication of surface nanoparticles and micro/nanograting structures on bulk pure aluminum in air using a 150 fs, 775 nm femtosecond laser. We investigate the size of the generated surface nanoparticles under irradiation with different femtosecond laser pulses. Smaller nanoparticles can be induced by a larger number of laser pulses and a lower laser fluence. In addition, we observe the formation of micro/nanogratings when the laser focus is scanned across a pure aluminum surface in air. We obtain micro- and nano-grating composite structures on a pure aluminum surface by adjusting the laser fluence and scan velocity. Femtosecond laser surface ablation of bulk pure aluminum in air is potentially a promising technique for efficient fabrication of surface nanostructures.     

Formation of intrinsic oxide nanocrystals on the surface of GaSe under laser irradiation

The process of GaSe surface oxidation is investigated. The work function is revealed to vary by 0.5 eV within a few hours after the formation of a cleaved facet of the semiconductor surface. It is demonstrated that low-energy laser irradiation with a wavelength of 650 nm leads to the generation of an intrinsic oxide on the crystallite surfaces. On account of continuous exposure to laser radiation for 6 h, the work function of the GaSe surface increases by 1 eV, i.e., becomes twice as large as that obtained without irradiation.     

Infrared femtosecond laser-induced great enhancement of ultraviolet luminescence of ZnO two-dimensional nanostructures

Two-dimensional (2D) complex nanostructures on the surface of ZnO crystal are fabricated by the interference of three 800 nm fs laser beams. The 2D nanostructures exhibit a great enhancement of UV emission excited by infrared fs laser with central wavelengths ranging from 1,200 nm to 2,000 nm. We propose that the defect states in the band gap of 2D nanostructures induced by 800 nm fs laser ablation cause the great enhancement of UV emission. We make theoretical calculations and explain well with the experimental results.     

Target-plane deposition of diamond-like carbon in pulsed laser ablation of graphite

In pulsed Nd:YAG laser ablation of highly oriented pyrolytic graphite (HOPG) at 10⁻⁶ Torr, diamond-like carbon (DLC) are deposited at laser wavelengths of 1064, 532, and 355 nm on substrates placed in the target-plane. These target-plane samples are found to contain varying sp³ content and composed of nanostructures of 40-200 nm in size depending on the laser wavelength and laser fluence. The material and origin of sp³ in the target-plane samples is closely correlated to that in the laser-modified HOPG surface layer, and hardly from the backward deposition of ablated carbon plume. The surface morphology of the target-plane samples shows the columnar growth and with a tendency for agglomeration between nanograins, in particular for long laser wavelength at 1064 nm. It is also proposed that DLC formation mechanism at the laser-ablated HOPG is possibly via the laser-induced subsurface melting and resolidification.     

Nanostructured core-shell Ni deposition on SiC particles by alkaline electroless coating

In this study, core-shell nanostructured nickel formation on silicon carbide (SiC) ceramic powders was achieved through the electroless deposition method using alkaline solutions. To produce a nano core-shell Ni deposition on the SiC surfaces, process parameters such as pH values, the type of reducer material, deposition temperature, stirring rate and activation procedure among others were determined. Full coverage of core-shell nickel structures on SiC surfaces was achieved with a grain size of between 100 and 300 nm, which was approximately the same deposition thickness on the SiC surfaces. The surface morphology of the coated SiC particles showed a homogenous distribution of nanostructured nickel grains characterized by scanning electron microscopy and X-ray diffraction techniques. The nanostructures of the crystalline Ni coatings were observed to be attractive for achieving both good bonding and dense structure. The thin core shell-structure of Ni on the SiC surfaces was assessed as a beneficial reinforcement for possible metal matrix composite manufacturing.     

Study of the angular and polarization structures of radiation scattered by monolayers of metal-containing nanostructures during their oxidation

The angular and polarization scattering characteristics of copper, nickel, and palladium monolayers composed of quasi-monodisperse nanograins 2–5 nm in size, as well as aggregates and chains of these nanograins, have been investigated during oxidation of monolayers with different packing densities of particles in a monolayer. On the basis of the experimental data, a number of integral scattering characteristics of monolayers of different metals and the angular dependences of the scattering matrix elements for laser wavelengths in the visible range have been calculated and analyzed. It is demonstrated that the polarization properties of the angular structure and the scattering matrix elements depend strongly on the degree of order of the structures and the presence of chains in monolayers of metal-containing nanostructures. Oxidation of nanostructures leads to the chaotic distribution of metal cores in a nanostructure. It is shown that scattering from nanostructures is more sensitive to oxidation in comparison with absorption. A nonlinear concentration dependence of scattering intensity was observed for copper nanostructures on a quartz substrate near the plasma resonance (at 633 nm) of all structures under study and at 440 nm for nanostructures on a silicon substrate (i.e., at the wavelength corresponding to strong absorption in silicon).     

Fabrication of complex nanostructures on ZnO crystals by the interference of three femtosecond laser beams

By adjusting the laser polarization combinations, fluences and pulse numbers, we fabricated several types of two-dimensional (2D) complex nanostructures on the surface of c-cut ZnO single crystal by the interference of three femtosecond laser beams with central wavelength of 800 nm, pulse duration of 50 fs and pulse repetition frequency of 1 kHz. The hexagonal 2D nanostructures with a period of 600 nm are very regular and uniform, in which nanoparticles, nanorings and nanoripples with sizes of 200 nm are embedded. Excited by 800 nm femtosecond laser pulses, the photoluminescence (PL) micrographs reveal that the 2D nanostructures can emit purer and brighter blue light compared with the plane surface. These nanostructures have potential applications in blue light-emitting diodes (LEDs), high density optical storage and other optoelectronic devices.     

Periodic surface nanostructures on polycrystalline ZnO induced by femtosecond laser pulses

Periodic surface nanostructures induced by femtosecond laser pulses on polycrystalline ZnO are presented. By translating the sample line-by-line under appropriate irradiation conditions, grating-like nanostructures with an average period of 160 nm are fabricated. The dependence of surface morphologies on the processing parameters, such as laser fluence, pulse number and laser polarization, are studied by scanning electronic microscope (SEM). In addition, photoluminescence (PL) analysis at room-temperature indicates that the PL intensity of the irradiated area increases significantly compared with the un-irradiated area. Using femtosecond laser pulses irradiation to fabricate periodic surface nanostructures on polycrystalline ZnO is efficient, simple and low cost, which shows great potential applications in ZnO-based optoelectronic devices.     

Femtosecond laser structuring of titanium implants

In this study we perform the first femtosecond laser surface treatment of titanium in order to determine the potential of this technology for surface structuring of titanium implants. We find that the femtosecond laser produces a large variety of nanostructures (nanopores, nanoprotrusions) with a size down to 20 nm, multiple parallel grooved surface patterns with a period on the sub-micron level, microroughness in the range of 1-15 μm with various configurations, smooth surface with smooth micro-inhomogeneities, and smooth surface with sphere-like nanostructures down to 10 nm. Also, we have determined the optimal conditions for producing these surface structural modifications. Femtosecond laser treatment can produce a richer variety of surface structures on titanium for implants and other biomedical applications than long-pulse laser treatments.     

Laser-induced fabrication of randomly distributed nanostructures in fused silica surfaces

The nanostructuring of dielectrics is a big challenge for laser patterning methods. In this study a novel laser structuring method for the fabrication of randomly distributed nanostructures, called laser-induced front side etching using in situ pre-structured metal layers (IPSM-LIFE), is presented. The pulsed laser irradiation of a thin metal film deposited onto a dielectric substrate with fluences below the ablation threshold results in the formation of randomly distributed metal structures by self-assembly processes. Further pulsed laser irradiation of these metal structures with higher or equal laser fluences causes the formation of complex patterns at the surface of the dielectric due to localized ablation and melting processes of the dielectric surface induced by the absorption of the laser energy by the metal structures and the local energy transfer into the dielectric surface. The pattern formation observed in the film and the dielectrics substrate after irradiation of 10 nm chromium layers on fused silica, with laser pulses (Δt _p =25 ns, λ=248 nm), was studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Different features with a lateral size down to a few tens of nanometers, like concentric ring patterns, donut-like structures, and bar patterns were observed at the dielectric.     

飞秒激光制备彩色镍

 采用飞秒脉冲激光在空气条件下扫描处理镍片表面,制备了彩色镍。用扫描电子显微镜、紫外-可见-近红外分光光度计、拉曼光谱仪等对其进行了表征。扫描电子显微镜测量显示,彩色镍表面出现了纳米激光诱导周期表面结构,结构周期为480～510 nm;紫外-可见-近红外分光光度计测量表明,彩色镍对波长为200～2 200 nm的光的反射率大大降低;拉曼谱表明样品表面形成了一定含量的氧化镍。     

采用飞秒激光诱导制备彩色金属

采用脉宽为35～65fs,中心波长为800nm的飞秒脉冲激光对经抛光的镍片进行表面扫描处理,并在金属表面上制备了彩色镍图案;设置不同的激光扫描速度和能量密度扫描处理不锈钢表面,亦制备了彩色图案。介绍了实验过程,分析了实验结果,扫描电子显微镜（SEM）形貌分析显示,经过飞秒激光扫描处理的金属表面出现了纳米量级的激光诱导周期表面结构（NC—LIPSS）,在镍上形成的结构周期约为480—510nm,在不锈钢上形成的结构周期约为480～540nm。     

不同烧蚀条件下飞秒激光脉冲诱导ZnO纳米结构研究

烧蚀条件对飞秒激光脉冲诱导氧化锌纳米结构有重要影响.研究了800 nm,150 fs,250 kHz的飞秒激光脉冲分别在空气中,去离子水中以及无水乙醇中垂直聚焦于氧化锌晶体表面,诱导形成不同形态的纳米结构.实验结果表明,在空气中利用飞秒激光脉冲辐照样品表面,形成了周期为180 nm的纳米线;在去离子水中辐照诱导形成了由氧化锌纳米线聚集而成的"纳米球";在无水乙醇中形成出现分叉结构的纳米线.拉曼光谱分析辐照前后晶体晶相结果表明,形成的纳米结构相对于辐照前特征峰437 cm-1强度有所下降,在570 cm-1处的峰值则显著增强.分析了在各种烧蚀条件下诱导形成纳米结构的演化过程以及物理机理.