Thermal properties and structure of electrospun blends of PVDF with a fluorinated copolymer

We report the structure and thermal properties of blends comprising poly(vinylidene fluoride) (PVDF) and a random fluorinated copolymer (FCP) of poly(methyl methacrylate)‐random‐1H,1H,2H,2H‐perfluorodecyl methacrylate, promising membrane materials for oil–water separation. The roles of processing method and copolymer content on structure and properties were studied for fibrous membranes and films with varying compositions. Bead‐free, nonwoven fibrous membranes were obtained by electrospinning. Fiber diameters ranged from 0.4 to 1.9 μm, and thinner fibers were obtained for PVDF content >80%. As copolymer content increased, degree of crystallinity and onset of degradation for each blend decreased. Processing conditions have a greater impact on the crystallographic phase of PVDF than copolymer content. Fibers have polar beta phase; solution‐cast films contain gamma and beta phase; and melt crystallized films form alpha phase. Kwei's model was used to model the glass transition temperatures of the blends. Addition of FCP increases hydrophobicity of the electrospun membranes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 312–322     

Size-controlled and monodisperse enzyme-encapsulated chitosan microspheres developed by the SPG membrane emulsification technique

The amphiphilic gradient copolymers of 2,2,2-trifluoroethyl methacrylate (TFEMA) and acrylic acid (AA) have been synthesized by using amphiphilic RAFT agent via emulsifier-free emulsion polymerization with a starved feed method of adding TFEMA. Different cosolvents are added into polymerization system to inhibit AA's homopolymerization of in aqueous phase. RAFT polymerization kinetics under different reaction conditions are discussed in detail. (1)H NMR results indicate that the obtained copolymer has a chain structure with AA segments gradually changing to TFEMA segments. The copolymer latexes exhibit good pH stability (pH value from 5 to 14) and Ca(2+) stability. The self-assembly behavior of gradient copolymers in selective solvents are observed and studied by transmission electron microscopy. All the copolymers can form spherical micelles, but the homogeneity and size of micelles are different.     

含氟丙烯酸酯共聚物制备超疏水表面及其形成机理的研究

以丙烯酸全氟烷基乙基酯和甲基丙烯酸甲酯为共聚单体, 分别以用微乳液聚合法和溶液聚合法制备的无规共聚物和用可逆加成-断裂链转移制备的嵌段共聚物作为成膜共聚物, 并以1,1,2-三氟三氯乙烷作为溶剂, 采用溶剂挥发成膜法可以直接制备出超疏水膜, 聚合物膜对水的接触角可达160°. 改变聚合物结构和成膜条件, 探讨了该类超疏水膜的形成机理和影响因素. 发现膜的表面形貌和疏水性与共聚物的组成、结构、分子量以及成膜条件密切相关, 随着共聚物中氟含量的增大, 膜的表面形貌都趋于平滑; 而且, 无规共聚物比嵌段共聚物更易形成粗糙度好的膜; 同时, 较大的聚合物分子量和适宜的高的成膜温度都对形成粗糙结构有利.     

Effects of altered reaction conditions on the synthesis of polyurethane-poly(2,2,2-trifluoroethyl methacrylate) triblock copolymer aqueous dispersion

Polyurethane-poly(2,2,2-trifluoroethyl methacrylate) (PU-PTFEMA) triblock copolymer aqueous dispersions were synthesized by three-step polymerization. In the first step, polyurethane prepolymers (PU) based on 2,4-toluene diisocyanate (TDI), polyether binary alcohol (N₂₂₀), α,α-dimethylol propionic acid (DMPA), hydroxypropyl acrylic acid (HPA), and butanediol (BDO) were prepared with butanediol as the chain extender and methylethylketon as solvent. The next step involved neutralization and dispersion in water, where prepolymers were neutralised by the addition of triethylamine (TEA). The last step was the seeded emulsion polymerization, where PU emulsion was used as seed, kalium persulfate (KPS) as initiator and 2,2,2-trifluoroethyl methacrylate (TFEMA) as comonomer. Factors influencing the synthesis of PU-PTFEMA copolymer aqueous dispersion were studied. Experimental data indicate that factors influencing the synthesis of PU-PTFEMA copolymer aqueous dispersion mainly involve reaction temperature, reaction time, the concentration of initiator, DMPA content, TFEMA content. Rotational viscometer and dynamic light scattering (DLS) were used to characterize the properties of copolymer aqueous dispersion.     

Thermal and optical properties of highly fluorinated copolymers of methacrylates

Copolymers of pentafluorophenylhexafluoroisopropyl methacrylate (FPPMA) with trifluoroethyl methacrylate (TFEMA) were prepared in THF solution and in bulk using azobisisobutyronitrile as a free radical initiator. The monomer reactivity ratios of TFEMA (M₁) and FPPMA (M₂) were calculated as r₁ = 0.55 and r₂ = 0.07. The refractive indices of poly(TFEMA) and poly(FPPMA) are very similar as 1.435 and 1.430, respectively, at 532 nm, and the copolymer films were transparent. The glass transition temperatures (T_g) of the copolymers were in the range of 80–90°C and showed a negative deviation from the Gordon–Taylor equation. The thermal decomposition temperature (T_d) was increased with the content of FPPMA in copolymers. Low water absorption for 1:1 FPPMA/TFEMA copolymer was detected. Copolymers of FPPMA with hexafluoroisopropyl methacrylate (HFPMA) were also prepared. The monomer reactivity ratios of HFPMA (M₁) and FPPMA (M₂) were calculated as r₁ = 0.43 and r₂ = 0.10. The T_gs of the copolymers were in the range of 88–95°C and showed also a negative deviation from the Gordon–Taylor equation. T_g and T_d of the copolymers were increased with the content of FPPMA. The refractive index of poly(HFPMA) (1.384 at 532 nm) is much lower than that of FPPMA homopolymer, but copolymer films obtained were clear and transparent. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis of poly[(2‐oxo‐1,3‐dioxolane‐4‐yl) methyl methacrylate‐co‐ethyl acrylate] by incorporation of carbon dioxide into epoxide polymer and the miscibility behavior of its blends with poly(methyl methacrylate) or poly(vinyl chloride)

This study was related to the investigation of the chemical fixation of carbon dioxide to a copolymer bearing epoxide and the application of the cyclic carbonate group containing copolymer‐to‐polymer blends. In the synthesis of poly[(2‐oxo‐1,3‐dioxolane‐4‐yl) methyl methacrylate‐co‐ethyl acrylate] [poly(DOMA‐co‐EA)] from poly(glycidyl methacrylate‐co‐ethyl acrylate) [poly(GMA‐co‐EA)] and CO₂, quaternary ammonium salts showed good catalytic activity. The films of poly(DOMA‐co‐EA) with poly(methyl methacrylate) (PMMA) or poly(vinyl chloride) (PVC) blends were cast from N,N′‐dimethylformamide solution. The miscibility of the blends of poly(DOMA‐co‐EA) with PMMA or PVC have been investigated both by DSC and visual inspection of the blends. The optical clarity test and DSC analysis showed that poly(DOMA‐co‐EA) containing blends were miscible over the whole composition range. The miscibility behaviors were discussed in terms of Fourier transform infrared spectra and interaction parameters based on the binary interaction model. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1472–1480, 2001     

Contact angles of surface nanobubbles on mixed self-assembled monolayers with systematically varied macroscopic wettability by atomic force microscopy

The dependence of the properties of so-called "surface nanobubbles" at the interface of binary self-assembled monolayers (SAMs) of octadecanethiol (ODT) and 16-mercaptohexadecanoic acid (MHDA) on ultraflat template-stripped gold and water on the surface composition was studied systematically by in situ atomic force microscopy (AFM). The macroscopic water contact angle (θ(macro)) of the SAMs spanned the range between 107° ± 1° and 15° ± 3°. Surface nanobubbles were observed on all SAMs by intermittent contact-mode AFM; their size and contact angle were found to depend on the composition of the SAM. In particular, nanoscopic contact angles θ(nano) < 86° were observed for the first time for hydrophilic surfaces. From fits of the top of the bubble profile to a spherical cap in three dimensions, quantitative estimates of nanobubble height, width, and radius of curvature were obtained. Values of θ(nano) calculated from these data were found to change from 167° ± 3° to 33° ± 58°, when θ(macro) decreased from 107° ± 1° to 37° ± 3°. While the values for θ(nano) significantly exceeded those of θ(macro) for hydrophobic SAMs, which is fully in line with previous reports, this discrepancy became less pronounced and finally vanished for more hydrophilic surfaces.     

Three different β‐cyclodextrins direct the emulsion copolymerization of a highly fluorinated methacrylate toward distinctive nanostructured particle morphologies

Stable colloidal dispersions of nanostructured semifluorinated acrylic particles with an unfluorinated core and an outer layer consisting of copolymers of the highly hydrophobic and lipophobic heptadecafluorodecyl methacrylate (FMA) were successfully synthesized with the assistance of three different cyclodextrins as phase‐transfer catalysts: β‐cyclodextrin (β‐CD), hydroxypropyl β‐cyclodextrin (HpCD), and methyl β‐cyclodextrin (MeCD). While all the cyclodextrins form a stable inclusion complex (IC) with FMA, only the ICs with the more hydrophilic HpCD and MeCD are soluble in water. Nevertheless, incorporation of FMA in the particle shell copolymer could be achieved also when using β‐CD. On the other hand, the morphology of the nanostructured particles was characterized by a “patchy” fluorinated shell dependent on the cyclodextrin used, the best results being obtained with MeCD. A monomer‐starved semicontinuous emulsion polymerization procedure was essential to favor the CD‐mediated incorporation of FMA into the copolymer structure and to achieve a stable colloidal dispersion even in the presence of small amounts of mixed anionic–nonionic surfactants. The thermal and surface properties of the latex films showed a good correlation with the shell composition and patchy nanostructured morphology of the particles. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

SiO2@P（MMA/BA/3FMA）复合纳米粒子的制备及膜性能

通过溶胶-凝胶法与半连续种子乳液聚合法相结合,以正硅酸乙酯(TEOS)制备的纳米SiO2为核,以甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)和甲基丙烯酸三氟乙酯(3FMA)的共聚物P(MMA/BA/3FMA)为壳,合成了SiO2@P(MMA/BA/3FMA)核-壳结构纳米复合粒子.为防止纳米SiO2的团聚,提高其与共聚物的结合力,用乙烯基三甲氧基硅烷(VTMS)对纳米SiO2进行改性.通过红外光谱、透射电子显微镜、动态激光散射粒度仪、静态接触角测试仪、X射线光电子能谱分析和热重分析等表征了乳液结构及膜性能.结果表明,获得的复合纳米粒子呈现粒径分布为40～50 nm的核-壳结构球型颗粒.由于含氟官能团的迁移使得氟元素在膜-空气界面富集,有效降低了膜的表面自由能.当3FMA质量分数达到25%时,膜表面自由能达到最低值(23.13 mN/m).随着3FMA含量的增加,共聚物初始热分解温度由350℃提高到390℃.     

All-acrylic film-forming colloidal polymer/silica nanocomposite particles prepared by aqueous emulsion polymerization

The efficient synthesis of all-acrylic, film-forming, core-shell colloidal nanocomposite particles via in situ aqueous emulsion copolymerization of methyl methacrylate with n-butyl acrylate in the presence of a glycerol-functionalized ultrafine silica sol using a cationic azo initiator at 60 °C is reported. It is shown that relatively monodisperse nanocomposite particles can be produced with typical mean weight-average diameters of 140-330 nm and silica contents of up to 39 wt %. The importance of surface functionalization of the silica sol is highlighted, and it is demonstrated that systematic variation of parameters such as the initial silica sol concentration and initiator concentration affect both the mean particle diameter and the silica aggregation efficiency. The nanocomposite morphology comprises a copolymer core and a particulate silica shell, as determined by aqueous electrophoresis, X-ray photoelectron spectroscopy, and electron microscopy. Moreover, it is shown that films cast from n-butyl acrylate-rich copolymer/silica nanocomposite dispersions are significantly more transparent than those prepared from the poly(styrene-co-n-butyl acrylate)/silica nanocomposite particles reported previously. In the case of the aqueous emulsion homopolymerization of methyl methacrylate in the presence of ultrafine silica, a particle formation mechanism is proposed to account for the various experimental observations made when periodically sampling such nanocomposite syntheses at intermediate comonomer conversions.     

A facile method for preparing sticky, hydrophobic polymer surfaces

Textured surfaces consisting of nanometer- to micrometer-sized lightly sulfonated polystyrene ionomer (SPS) particles were prepared by rapid evaporation of the solvent from a dilute polymer solution-cast onto silica. The particle textured ionomer surfaces were prepared by either spin-coating or solution-casting ionomer solutions at controlled evaporation rates. The effects of the solvent used to spin-coat the film, the molecular weight of the ionomer, and the rate of solvent evaporation on the surface morphology of cast films were investigated. The surface morphologies were consistent with a spinodal decomposition mechanism, where the surface first existed as a percolated-like structure and then ripened into droplets if molecular mobility was retained for sufficient time. The SPS particles or particle aggregates were robust and resisted separation from the surface even after annealing at 120 °C for 1 week. The water contact angles on as-prepared surfaces were relatively low, ～90°, due to the polar groups in the ionomer, but when the surface was modified by chemical vapor deposition of 1H,1H,2H,2H-perfluorooctyltrichlorosilane, the surface contact angles increased to ～109° on smooth surfaces and up to ～140° on the textured surfaces. Although the surfaces were hydrophobic, the contact angle hysteresis was relatively high and water droplets stuck to these surfaces even when the surface was turned upside down.     

An AFM, XPS and wettability study of the surface heterogeneity of PS/PMMA-r-PMAA demixed thin films

A series of homopolymer/random copolymer blends was used to produce heterogeneous surfaces by demixing in thin films. The chosen homopolymer is polystyrene (PS) and the random copolymer is poly(methyl methacrylate)-r-poly(methacrylic acid) (PMMA-r-PMAA), whose acidic functions could be used as reactive sites in view of further surface functionalization. The proportion of each polymer at the interface was deduced from X-ray photoelectron spectroscopy (XPS) data using, on the one hand, the O/C ratio, and on the other hand, decomposition of the carbon peak of the blends in two components corresponding to the carbon peaks of PS and PMMA-r-PMAA. Combining the information from XPS with atomic force microscopy (AFM) images, water contact angle measurements and PS selective dissolution, it appears that the surfaces obtained from blends with a high PS content (90/10 to 70/30) display pits with a bottom made of PMMA-r-PMAA, randomly distributed in a PS matrix. On the other hand, the surfaces obtained from blends with a low PS content (30/70 to 10/90) display randomly distributed PS islands surrounded by a PMMA-r-PMAA matrix. The characteristics of the heterogeneous films are thought to be governed by the higher affinity of PMMA-r-PMAA for the solvent (dioxane), which leads to the elevation of the PS phase compared to the PMMA-r-PMAA phase, and to surface enrichment in PMMA-r-PMAA.     

Studies on suspension and emulsion. XXXV. Effect of epoxy groups at the surface layer of ethyl acrylate–glycidyl methacrylate copolymer emulsion particles on its crosslinking reactivity

The effect of epoxy groups at the surface layer of ethyl acrylate–glycidyl methacrylate copolymer (1) emulsion particles on its crosslinking reactivity has been investigated. For this purpose two series of I emulsions were prepared. In the Y series, of which emulsion particles have epoxy groups at the surface layer, the epoxy content in the polymerization recipe was varied. For preparing the X series, of which emulsion particles have few epoxy groups at the surface layer, the high epoxy content of a given emulsion was reduced by various degrees of cleavage reaction with HCl–CaCl₂. In emulsion blend films with amine-group-containing copolymer (II) emulsion, where the crosslinking reaction was expected to proceed only at the interfacial layer of I and II emulsion particles, the Y series, compared to the X series at the equal overall epoxy content in particles, showed less swelling and higher gel fraction in dioxane, less swelling in water, and higher tensile strength and modulus. On the other hand, this difference was not observed in the next two crosslinked films in which crosslinking was expected to be homogeneous. First, blends of I and II, which were isolated from the corresponding emulsions discussed above, were cast from dioxane solutions. Second, I emulsions were cast with BF₃ ether complex which was expected to penetrate into the particles. It is concluded that the response of I emulsion cleaving the epoxy groups at the surface layer of particles to subsequent interfacial crosslinking is obviously reduced. However, even such an emulsion can be crosslinked to an extent similar to that of an uncleaved emulsion with similar overall epoxy content, if the crosslinking reaction is conducted so as to give an homogeneous effect.     

含无规共聚物三元共混体系SMMA-PMMA-SAN相行为

含无规共聚物共混体系的相容性研究正在成为近年来的研究热点 ,因为相容的驱动力来自共聚物分子内不同单体链段间的排斥性相互作用 [1～ 3] .目前研究这类体系还主要采用过份简化的 F- H平均场理论 ,用旨在克服平均场理论缺陷的 Flory状态方程 ( EOS)理论仅局限于研究二元共聚物共混体系[4～ 8] .与三元共混体系相比 ,用 EOS理论预测含两个无规共聚物三元体系相行为尚需确定共聚物 -共聚物间的二元参数 sj/si,Xij和 Qij.若用 Ax B1- x和 Cy D1- y分别代表共聚物 1和 2 ,则 A,B,C,D代表相应共聚物中的单体单元 ,x,y分别是 1和 2的共…     

Phase behavior of tetramethylpolycarbonate blends with styrene‐based methacrylate copolymers and their interaction energies

The miscibility of tetramethylpolycarbonate (TMPC) blends with styrenic copolymers containing various methacrylates was examined, and the interaction energies between TMPC and methacrylate were evaluated from the phase‐separation temperatures of TMPC/copolymer blends with lattice‐fluid theory combined with a binary interaction model. TMPC formed miscible blends with styrenic copolymers containing less than a certain amount of methacrylate, and these miscible blends always exhibited lower critical solution temperature (LCST)‐type phase behavior. The phase‐separation temperatures of TMPC blends with copolymers such as poly(styrene‐co‐methyl methacrylate), poly(styrene‐co‐ethyl methacrylate), poly(styrene‐co‐n‐propyl methacrylate), and poly(styrene‐co‐phenyl methacrylate) increase with methacrylate content, go through a maximum, and decrease, whereas those of TMPC blends with poly(styrene‐co‐n‐butyl methacrylate) and poly(styrene‐co‐cyclohexyl methacrylate) always decrease. The calculated interaction energy for a copolymer–TMPC pair is negative and increases with the methacrylate content in the copolymer. This would seem to contradict the prediction of the binary interaction model, that systems with more favorable energetic interactions have higher LCSTs. A detailed inspection of lattice‐fluid theory was performed to explain such phase behavior. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1288–1297, 2002     

Controlling the size of nanostructures in thin films via blending of block copolymers and homopolymers

The effects of molecular weight and concentration of poly (methyl methacrylate) (PMMA) homopolymer or symmetric short polystyrene-block-poly (methyl methacrylate) (PS-b-PMMA) diblock copolymer on the size of the nanostructures of its blends with symmetric long PS-b-PMMA diblock copolymer have been investigated by atomic force microscopy. By careful controlling of the film thickness, solvent selectivity, and annealing time, PMMA cylindrical microdomains oriented normal to the film surface were obtained in all thin films. With the addition of both low- and high-molecular-weight PMMA homopolymers, the cylindrical domain sizes increased although it was less obvious for the lower molecular weight homopolymer. In contrast to the homopolymer, adding the short chain diblock copolymer resulted in a decrease in the cylindrical domain size, which was ascribed to the reduction of the interfacial tension and increase in the stretching energy.     

Designing superhydrophobic surface based on fluoropolymer–silica nanocomposite via RAFT‐mediated polymerization‐induced self‐assembly

Superhydrophobic surfaces (SHS) find versatile applications as coatings due to their very high water‐repellency, self‐cleaning, and anti‐icing properties. This investigation describes the preparation of a SHS from surfactant‐free hybrid fluoropolymer latex. In this case, reversible addition‐fragmentation chain transfer (RAFT) polymerization was adopted to prepare a copolymer of 4‐vinyl pyridine (4VP) and vinyl triethoxysilane (VTES), where the pyridine units were quaternized to make the copolymer soluble in water. The copolymer was further used as a macro‐RAFT agent to polymerize 2,2,2‐trifluoroethyl methacrylate (TFEMA) in a surfactant‐free emulsion via polymerization‐induced self‐assembly (PISA). The macro‐RAFT agent contained a small amount of VTES as co‐monomer which was utilized to graft silica nanoparticles (SNPs) onto the P(TFEMA) spheres. The film prepared using the nanocomposite latex exhibited a nano‐structured surface as observed by SEM and AFM analyses. Surface modification of the film with fluorinated trichlorosilane produced an SHS with a water contact angle (WCA) of 151.5°. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 266–275     

Morphology Evolution of Block Copolymer Blend Thin Films Induced by Solvent Vapor Annealing

ABSTRACT

Self-assembly of binary block copolymer blends in thin film induced by solvent vapor annealing has been systematically studied. The diblock copolymers polystyrene-b-poly(2-vinylpyridine) with different molecular weights and volume fractions were blended with different molar ratios to cast thin films on silica substrate by spin coating. The films were annealed separately in the vapor of ethanol or toluene over time to induce morphology transformations from spheres, gyroids, and bicontinuous nanostructures, depending on the blending ratio, solvent selectivity, and annealing time, as investigated by atomic force microscopy and X-ray photoelectron spectroscopy. The formation and transformation mechanism of the self-assembly structure are discussed in the context of solvent-copolymer interactions. This study provides new insights into the simple manipulation of self-assembled nanostructures of block copolymer thin films.     

Physically controlled,free‐radical polymerization of vaporized fluoromonomer on solid surfaces

Gas/vapor‐deposition polymerization (GDP) of vinyl monomer is expected to exhibit a unique polymerization behavior different from its polymerization in the liquid phase. Free‐radical GDP of 2,2,3,3,3‐pentafluoropropyl methacrylate (FMA) was carried out with a conventional free‐radical initiator (azobisisobutyronitrile) on substrate surfaces. A linear relationship between the number‐average molecular weight and polymer yield was observed, and the consecutive copolymerization of methyl methacrylate (MMA) and FMA led to the formation of block copolymer P(MMA‐block‐FMA). These results suggested that the GDP process on substrate surfaces has a living nature. During the process, the active species at growing chain ends may be immobilized on the deposit surface and restricted from the chain‐transfer reactions, resulting in a continuation of the propagation reaction. The GDP on substrate surfaces is therefore a physically controlled polymerization process. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2621–2630, 2004     

Deviations from bulk morphologies in thin films of block copolymer/additive binary blends

Deviations from bulk morphologies in thin films of binary blends of alkyne-functionalized diblock copolymer poly(ethylene oxide)-block-poly(n-butyl methacrylate-random-propargyl methacrylate) (PEO-b-P(nBMA-r-PgMA)) and Rhodamine B azide are reported, where thermal click reaction between the two components leads to microphase separated morphologies. Both in the bulk and in thin films, increasing the azide loading ratio resulted in the transition from a lamellar microdomain morphology to a hexagonally packed cylindrical mircodomain morphology. However, in thin films the lamellae-cylinder transition was observed at a different azide loading ratio, which was determined by film thickness. As a result, significant deviations from the bulk morphology were observed. These results indicate that surface interactions and confined geometry can play an important role in dictating the morphology in thin films of BCP/additive binary blends.