Cloud point extraction: an alternative to traditional liquid-liquid extraction for lanthanides(III) separation

Cloud point extraction (CPE) was used to extract and separate lanthanum(III) and gadolinium(III) nitrate from an aqueous solution. The methodology used is based on the formation of lanthanide(III)-8-hydroxyquinoline (8-HQ) complexes soluble in a micellar phase of non-ionic surfactant. The lanthanide(III) complexes are then extracted into the surfactant-rich phase at a temperature above the cloud point temperature (CPT). The structure of the non-ionic surfactant, and the chelating agent-metal molar ratio are identified as factors determining the extraction efficiency and selectivity. In an aqueous solution containing equimolar concentrations of La(III) and Gd(III), extraction efficiency for Gd(III) can reach 96% with a Gd(III)/La(III) selectivity higher than 30 using Triton X-114. Under those conditions, a Gd(III) decontamination factor of 50 is obtained.     

1-(2-pyridylazo)-2-naphthol (PAN) as extractant in solid-liquid extraction of some trivalent rare earth elements

In the present paper, solid-liquid extraction behaviour of RE(III) (RE La, Ce, Pr, Nd, Sm, Gd, Dy and Yb) by the use of 1-(2-pyridylazo)-2-naphthol (PAN, HL) as an extractant in paraffin (m.p. 48 approximately 50 degrees) has been investigated at 80 +/- 0.07 degrees. The effect of equilibrium time, pH of aqueous phase, concentration of extractant in paraffin and solid diluent as well as buffer solution used on the extraction efficiency of RE(III) have been discussed. The extraction reaction is RE(3+) + 2HL(o) + Cl(-) <==> REL(2)Cl(o) + 2H(+).     

Solid phase extraction and spectrophotometric determination of Au(III) with 5-(2-hydroxy-5-nitrophenylazo)thiorhodanine.

A new chromogenic reagent, 5-(2-hydroxy-5-nitrophenylazo)thiorhodanine (HNATR) was synthesized. A highly sensitive, selective and rapid method for the determination microg l(-1) level of Au(III) based on the rapid reaction of Au(III) with HNATR and the solid phase extraction of the colored complex with a reversed phase polymer-based C(18) cartridge have been developed. The HNATR reacted with Au(III) to form a red complex of a molar ratio 1:2 (Au(III) to HNATR) in the presence of 0.05 - 0.5 mol l(-1) of phosphoric acid solution and emulsifier-OP medium. This complex was enriched by the solid phase extraction with a polymer-based C(18) cartridge. The enrichment factor of 100 was achieved. The molar absorptivity of the complex is 1.37 x 10(5) l mol(-1) cm(-1) at 520 nm in the measured solution. The system obeys Beer's law in the range of 0.01 - 3 microg ml(-1). The relative standard deviation for eleven replicates sample of 0.5 microg l(-1) level is 2.18%. The detection limit, based on the three times of standard deviation is 0.02 microg l(-1) in the original sample. This method was applied to the determination of gold in water and ore with good results.     

Spectrophotometric determination of manganese with 1-(2-pyridylazo)-2-naphthol and a non-ionic surfactant

A spectrophotometric method for the determination of trace amounts of manganese with 1-(2-pyridylazo)-2-naphthol (PAN) is described. The method is based on the measurement of absorbance of the manganese—PAN chelate solubilized with a non-ionic surfactant, Triton X-100. No extraction procedure is required in the method proposed. High concentrations of calcium, aluminium and magnesium do not interfere. The presence of up to 10 ppm of lead can be tolerated. Iron, cadmium, zinc, cobalt and nickel can be effectively masked with potassium cyanide. Beer's law is obeyed up to 2 ppm of manganese. The molar absorptivity of the manganese—PAN chelate found was 4.4 × 10⁴ l. mole ⁻¹. cm⁻¹ at 562 nm. The overall stability constant of Mn(PAN)₂ in 0.4% Triton X-100 medium is 10^16.8.     

Selective extraction of iron(III) from aqueous nitrate solution in the presence of cobalt(II), copper(II) and nickel(II) ions using bis(delta2-2-imidazolinyl)-5,5'-dioxime.

The feasibility of using bis(delta2-2-imidazolinyl)-5,5'-dioxime (H2L) for the selective extraction of iron(III) from aqueous solutions was investigated by employing an solvent-extraction technique. The extraction of iron(III) from an aqueous nitrate solution in the presence of metal ions, such as cobalt(II), copper(II) and nickel(II), was carried out using H2L in binary and multicomponent mixtures. Iron(III) extraction has been studied as a function of the pH, equilibrium time and extractant concentration. From the extracted complex species in the organic phase, iron(III) was stripped with 2 M HNO3, and later determined using atomic-absorption spectrometry. The extraction was found to significantly depend on the aqueous solution pH. The extraction of iron(III) with H2L increases with the pH value, reaching a maximum in the zone of pH 2.0, remaining constant between 2 and 3.5 and subsequently decreasing. The quantitative extraction of iron(III) with 5 x 10(-30 M H2L in toluene is observed at pH 2.0. H2L was found to react with iron(III) to form ligand complex having a composition of 1:2 (Fe:H2L).     

Two Stage Solid Phase Extraction with Subsequent HPLC Isolation for Structure Elucidation of Major Metabolites of (+)-(R)-2-{3-(benzo[1,4]dioxan-2-yl-methylamino)-1-propyl}-3(2H)-pyridazinone (GYKI-16084)

GYKI-16084 – (+)-(R)-2-{3-(benzo[1,4]dioxan-2-yl-methylamino)-1-propyl}-3(2H)-pyridazinone hydrochloride – is a new drug candidate for the treatment of benign prostatic hyperplasia. In our study the major metabolites formed in the rat and dog were isolated from dog and rat urine, then their structures were elucidated by means of MS and NMR. A two stage solid phase extraction (SPE) procedure and a semi-preparative HPLC method were developed utilizing various mechanisms of separation. The major metabolites proved to be isomeric glucuronides of the benzodioxane moiety hydroxylated at positions 6 or 7 and {2-(2-carboxyethyl)-3(2H)-pyridazinone}.     

The influence of methanol and ethanol on the efficiency of extraction of lanthanides(III) with 1-(2-pyridylazo)-2-naphthol (PAN) in carbon tetrachloride

The efficiency of extraction of microquantities of Eu(III), Sm(III) and Gd(III) from water—50% (v/v) methanol phase or water—50% (v/v) ethanol phase withPAN solutions in CCl₄ was examined. Separation factors for the following pairs of lanthanides(III) were determined: Eu-Sm, Eu-Gd, Sm-Gd, as well as Eu-Ln, Sm-Ln and Gd-Ln, where:Ln=Tb, Ho, or Lu; their changes with respect to the composition of the polar phase were also estimated.

---

Der Einfluß von Methanol und Ethanol auf die Effektivität der Extraktion der Lanthaniden mit Lösungen von 1-(2-pyridylazo)-2-naphthol (PAN) in Tetrachlorkohlenstoff

Zusammenfassung Die Effektivität der Extraktion von Mikromengen Eu(III), Sm(III) und Gd(III) aus der Wasser-Methanol- und Wasser-Ethanol-Phase (50 vol. %), mit Hilfe vonPAN-Lösungen in CCl₄ wurde untersucht. Die Trennfaktoren für nachstehende Lanthaniden(III)-Paare: Eu-Sm, Eu-Gd, Sm-Gd und Eu-Ln, Sm-Ln, Gd-Ln(Ln=Tb, Ho oder Lu) wurden berechnet und ihre Änderungen in der Abhängigkeit von der polaren Phase geschätzt.

     

Micellar chromatographic separation of vanadium(V) chelate with 2-(2-thiazolylazo)-5-dimethylaminophenol

Summary In reversed phase—high performance liquid chromatography for metal chelates with 2-(2-thiazolylazo)-5-dimethylaminophenol, an aqueous non-ionic surfactant solution is used as a mobile phase. Among V(V), Fe(III), Cu(II), Co(II), Ni(II), Cd(II), Zn(II), Mn(II), and Al(III), only the V(V) chelate gave a resolved peak by using 0.8% w/w poly(oxyethylene)_n-4-nonylphenyl ether (n=20) solution buffered at pH 3.8. V(V) can be selectively separated and sensitively determined.     

Synthesis and characterization of 2-(3,5-Dichloro-2-pyridylazo)-5-dimethylaminophenol as a reagent for determination of lanthanum

2-(3,5-Dichloro-2-pyridylazo)-5-dimethylaminophenol (3,5-diCIDMPAP) has been synthesized and its spectral properties, acid-base equilibria, physical constants, and solubility and stability are presented. This reagent is highly promising for the determination of lanthanides. The influence of Triton X-100 on the dissociation constant has been investigated and the association constant between the reagent and the surfactant determined. Analytical data for the 3,5-diCIDMPAP complexes with La(III), Eu(III), Gd(III), Er(III) and Yb(III) are given, La(III) in synthetic samples has been determined with 3,5-diCIDMPAP.     

Extraction of gallium(III) by 1-{[2-(2,4-dichlorophenyl)-4-propyl-1,3-dioxolan-2-yl]methyl}-1H-1,2,4-triazole from hydrochloric acid solutions

The extraction of gallium(III) with 1-{[2-(2,4-dichlorophenyl)-4-propyl-1,3-dioxolan-2- yl]methyl}-1H-1,2,4-triazole from hydrochloric acid solutions into toluene was studied. It was found that gallium( III) was efficiently extracted from 5–10 M solutions of HCl by the anion-exchange mechanism. The following metal extraction order was determined in the above aqueous phase acidity range: Ga(III) > In(III) > Al(III). The concentration constants and the thermodynamic parameters of the reaction of gallium(III) extraction from 6 M solutions of HCl at 25 °C were calculated.     

Rapid quantitation of 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK) and its metabolite 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol (NNAL) in rat urine using ultra-fast liquid chromatography mass spectrometry (UFLC/MS/MS)

The tobacco-specific nitrosamine 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK) is a component of tobacco smoke and is rapidly metabolized to 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol (NNAL). Limited information is available on the relative systemic exposures resulting from NNK administration via the oral, intraperitoneal injection, and inhalation routes. Moreover, there is a need for a rapid method for simultaneous quantitative analyses of NNK and NNAL in rat urine. We developed a method based on Ultra Fast Liquid Chromatography Mass Spectrometry (UFLC/MS/MS) for the extraction and analysis of the potent lung carcinogens NNK and NNAL. Following addition of synthetic labeled internal standards, urine was introduced to 96 well plate Evolute^® Express CX 30?mg solid phase extraction system. The eluates were dried under vacuum and reconstituted in mobile phase before injecting to the LC system. The use of UFLC allowed for a 7.1?min run time. The precision and accuracy of the samples was 1.2-6.6% relative standard deviation (%RSD) and 91-113% of the concentration added, respectively. The limits of detection for NNK and NNAL were 70 and 3.0?pg/mL, respectively. The selectivity and sensitivity of this method improves the ability to measure these compounds at low concentrations and greatly facilitate toxicological studies of the NNK and NNAL.     

Cloud point extraction of lanthanide(III) ions via use of Triton X-100 without and with water-soluble calixarenes as added chelating agents

The use of water-soluble calixarenes: p-sulfonato thiacalixarene (ST), tetra-sulfonatomethylated calix[4]resorcinarene (SR), calix[4]resorcinarene phosphonic acid (PhR) as chelating agents in cloud point extraction (CPE) of La(III), Gd(III) and Yb(III) ions using Triton X-100 as non-ionic surfactant is introduced. The data obtained indicate that both complexation ability and structure of calixarenes govern the extraction efficiency of lanthanides. In particular ST and SR, forming 1:1 lanthanide complexes with similar stability in aqueous media, exhibit different extractability when used as chelating agents in CPE. First synthesized PhR was found to be the most efficient chelating agent exhibiting pH-dependent selectivity within La(III), Gd(III) and Yb(III) in CPE.     

Simultaneous determination of methylprednisolone and methylprednisolone 21-[8-[methyl-(2-sulfoethyl)amino]-8-oxooctanoate] sodium salt in human urine by high-performance liquid chromatography with ultraviolet detection

A reversed-phase high-performance liquid chromatographic assay with ultraviolet detection at 243 nm has been developed for the quantitative determination of methylprednisolone (MP) and methylprednisolone 21-[8-[methyl-(2-sulfoethyl)amino]-8-oxooctanoate] sodium salt (MPSO) in human urine following therapeutic doses in humans. The assay procedure involves stabilization of urine samples by addition of disodium ethylenediaminetetraacetic acid (Na2EDTA) and ion-pair extractions of MPSO using tetraethylammonium chloride (TEACl) as the counter ion. After extracting both drugs and internal standard into chloroform, the extract was evaporated to dryness under nitrogen. The resulting residue was reconstituted in 200-500 microliters of mobile phase and chromatographed on an IBM C18 reversed-phase column (5 microns). The mobile phase was a mixture of water-acetonitrile-isopropanol (71.2:18.8:10.0, v/v) containing 75 microliters of 0.1 M hydrochloric acid and 0.450 g of TEACl per liter. Propyl p-hydroxybenzoate was used as an internal standard. The extraction efficiencies of MP and MPSO were greater than 90% using the ion-pairing agent TEACl. The chromatographic responses were linear up to about 200 micrograms/ml for MP and 80 micrograms/ml for MPSO and had sufficient precision and accuracy to provide quantitative data from human urine. The assay detection limit was about 8 ng/ml for MP and 25 ng/ml for MPSO in human urine. Stability studies in urine indicated that without Na2EDTA stabilization and at room temperature, rapid degradation of MPSO occurred in urine. Addition of EDTA to the urine specimen and storage at -70 degrees C increased the stability of MPSO, and little or no degradation was observed in urine stored for more than 60 days. The method has been used in the simultaneous determination of MP and MPSO in urine specimens obtained from a single-dose tolerance study of MPSO in normal male volunteers.     

Extraction of Ce(III), Gd(III) and Yb(III) from Citrate Medium by High Molecular Weight Amines

Abstract

High molecular weight amines have been used for the extraction of citrate complexes of Ce(III), Gd(III) and Yb(III). The effect of different variables on extraction has been studied. The citrate species extracted in the organic phase have been proposed as [(RNH₃ ⁺)₃] [M(Cit)₂]^3-.     

Liquid-liquid extraction and high-performance liquid chromatography for the determination of a novel antidysrhythmic agent (UK-68,798) in human urine.

A routine method for the determination of a novel class III antidysrhythmic agent, 1-(4-methanesulphonamidophenoxy)-2-[N-(4-methanesulponamidophen ethyl)- N-methylamino]ethane, in human urine has been developed. The method involves solvent extraction followed by high-performance liquid chromatography on an unmodified silica column with ultraviolet detection. Despite a low recovery of drug through the three-stage extraction procedure a reliable assay with high precision (coefficient of variation less than 6%) and a limit of determination of 2.5 ng/ml was achieved. The method has been applied to the analysis of samples following single oral and intravenous doses of 1-12.5 micrograms/kg of the drug to human volunteers.     

Bioanalysis of (E)-5-(2-bromovinyl)-2'-deoxyuridine

(E)-5-(2-Bromovinyl)-2'-deoxyuridine is an antiviral drug that is experimentally used for modulation of the antitumour effect of fluoropyrimidines, such as ftorafur and 5-fluorouracil. The isolation of the analyte, in the presence of 5-fluorouracil, from the matrix is performed either by means of a simple protein precipitation (plasma) or by means of a liquid-liquid extraction with ethyl acetate (urine). Following pretreatment, the analyte is analysed by reversed-phase chromatography and quantified by absorbance detection at 307 nm. The minimum detectable concentration in plasma and urine samples is ca. 6 ng/ml. The recovery after deproteination of plasma samples is 75%, while after liquid-liquid extraction of urine the recovery amounts 92%. The degree of protein binding of the analyte, measured by ultrafiltration, is found to be 97%. These data allow the bioanalysis of (E)-5-(2-bromovinyl)-2'-deoxyuridine for pharmacokinetic studies.     

Liquid-liquid extraction separation of iron (III) with 2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester

Liquid-liquid extraction separation of iron(III) with 2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester (PC-88A) in toluene has been studied. Quantitative extraction of iron(III) with 5 x 10(-3) M PC-88A in toluene is observed in the pH range 0.75-2.5. From the extracted complex species in the organic phase iron(III) was stripped with 1-4 M HNO(3), 1.5-4 M H(2)SO(4) and 1.5-4 M HCl, and later determined spectrophotometrically by thiocyanate method. Separation of iron(III) was carried out with some of the first transition metals in binary and multicomponent mixtures. This method was extended for the determination of iron in real samples.     

Determination of endocrine disrupting chemicals in environmental solid matrices by extraction with a non-ionic surfactant (Tween 80)

A readily applicable method based on extraction by aqueous non-ionic surfactant solutions (Tween 80) and RP-HPLC coupled to fluorescence detection, has been developed for the simultaneous determination of the phenolic endocrine disrupting chemicals (EDCs) nonylphenol (NP), nonylphenol monoethoxylate (NP1EO) and nonylphenol diethoxylate (NP2EO) and bisphenol A (BPA) in environmental solid matrices. Clean up of sample extracts was performed on Si-C18 solid phase extraction (SPE) cartridges. The overall Tween 80 extraction-SPE-RP-HPLC procedure was validated for accuracy and precision by analyzing sediment samples spiked with known amounts of EDCs. Recoveries for NP, NP1EO, NP2EO and BPA and limits of detection are in agreement with conventional extraction methods. The developed methodology was successfully applied to the analysis of target compounds in Italian river sediments, river suspended matter and benthonic macroinvertebrate organisms (oligochaetes Lumbriculus variegatus). Results confirmed that this relatively simple procedure performed satisfactorily in the determination of phenolic EDCs in environmental solid matrices of different complexity and that it can be a suitable alternative method to conventional systems even for routine analyses.     

Selective extraction of gold(III) in the presence of Pd(II) and Pt(IV) by salting-out of the mixture of 2-propanol and water

The mixture of 2-propanol with water has been employed to extract Au(III) along with other precious metals such as Pd(II) and Pt(IV) by using NaCl in the concentration range of 2.5-4.0 mol dm(-3). Upon the addition of NaCl within this concentration range (2.5-4.0 mol dm(-3)) phase separation was attained. Gold(III) in aqueous phase was quantitatively extracted into the 2-propanol phase at 2.5-4.0 mol dm(-3) of NaCl. The extraction of the other metals such as Pd(II) and Pt(IV) was much lower than for that of Au(III). Thus a maximal selective separation of Au(III) from these metals could be attained using the mixture of 2-propanol with water. A reaction mechanism involving the ion-pair of Na(+) and [AuCl(4)](-) has been proposed to explain this extraction.     

Reversed-phase HPLC determination of Co(II), Ni(II) and Fe(III) as their 2-(2-thiazolylazo)-5-dimethylaminophenol chelates

The optimum chromatographic separation conditions for Co(II), Ni(II), and Fe(III) chelates with 2-(2-thiazolylazo)-5-dimethylaminophenol (TAM) were investigated. The compositions of chelates were also determined by the HPLC method and thus the possible structure of chelates was given. A precolumn derivatization method was used, followed by separation on an octyl-bonded silica stationary phase with a methanol-tetrahydrofuran-water (40:9:51, v/v/v) mobile phase containing pH 5.8 acetate buffer and 1 x 10(-4)M TAM. The detection limits of Co(II), Ni(II), and Fe(III) at 560 nm are 0.03, 0.02 and 0.1 ng (S N = 2 ), respectively. They can be determined by means of the proposed method without interference from other common metal ions and have been determined in five standard alloys with satisfactory results.