电化学振荡反应在黄芩提取工艺优化中的应用

以H2SO4 - KBrO3- MnSO4- CH3COCH3为电化学振荡反应体系,采用电化学方法获取黄芩不同提取条件下电化学指纹图谱,根据指纹图谱特征参数诱导时间考察黄芩提取液总成分含量,优化黄芩提取的最佳工艺为: 采用10倍量的水,提取3次,每次2 h.结果表明,黄芩提取液浓度和诱导时间(tin)呈良好的线性关系,其线性回归方程为tin=-570C+7176(r=0.9970),线性范围为5.0～12.2 g/L.     

具有油水分配系数测算功能的中药指纹图谱

建立了一种能同时测算中药中主要成分的油水分配系数Pow的功能化中药指纹图谱。采用微乳液电动色谱,以中药女贞子为例,对运行缓冲液浓度、pH值、十二烷基硫酸钠浓度等参数进行了优化。利用SPSS程序对磺胺等从女贞子中提取的6种标准化合物组分的迁移时间tm与其log Pow文献值进行非线性拟合,得到女贞子提取组分的标准方程线性关系良好（r=0.9880）。在相同的实验条件下测得化合物的log Pow与文献报道值较好的符合,证明该方法可靠。获得了能代表组分疏水化学特征的中药指纹图谱,测得女贞子的主要有效成分齐墩果酸的log Pow为3.63。该指纹图谱较为可靠地提供了女贞子中各种成分的log Pow,直观地反映出各组分油水分配性质的分布,对中药有效成分提取溶剂的选择、剂型的设计及制剂工艺的改进具有指导意义。     

质谱差谱方法及其在中药复方研究中的应用

采用HPLC-ESI-MSn分析得到了复方合煎液中有效部分提取物的指纹图谱数据, 通过比对找出对复方指纹谱有贡献的有效成分峰. 再用质谱差谱方法处理多级质谱数据, 提取不同类型的中性丢失, 实现了对复方有效成分化合物的快速分类鉴定. 用该法研究了复方柴苓汤有效部分黄芩总黄酮和柴胡总皂苷.     

山蜡梅叶颗粒的高效液相色谱指纹图谱定性及定量分析

应用高效液相色谱法建立可同时对山蜡梅叶颗粒进行鉴别和有效成分含量测定的色谱指纹图谱。以Cosmosil C18色谱柱为分离柱,甲醇与甲酸混合溶液进行梯度洗脱,检测波长为365 nm。成分芦丁、槲皮素和山奈素的质量浓度均与峰面积呈线性关系,线性范围分别为4.6~110.4,1.0~24.0,1.5~36.0 mg.L-1。运用中药色谱指纹图谱相似度评价系统2004版进行分析,20批样品平均相似度为95%以上。颗粒剂中三个成分的含量分别为芦丁含量(130±20)μg.g-1,槲皮素含量(35±10)μg.g-1,山奈素含量(60±10)μg.g-1。建立的山蜡梅叶颗粒的色谱指纹图谱,为质量控制提供新方法。     

淫羊藿属药材反相高效液相色谱指纹图谱及质量评估研究

用一种新的多台阶梯度洗脱的反相高效液相色谱(RPLC)法, 首次建立了秦岭山区产4种产地及亚属均不相同的淫羊藿属药材的由9种成分组成的色谱指纹图谱. 并以淫羊藿甙为内标作为相对标准, 对其质量进行了评估. 然而, 因其产地和亚属的不同, 指纹图谱又各有特征, 发现产地不同的两种淫羊藿亚属, 箭叶淫羊藿的RPLC指纹图谱由12个色谱峰组成. 还提出用相对含量比较法对各种类淫羊藿中9种成分的含量进行了质量评价. 本工作所建立的淫羊藿属药材的RPLC指纹图谱法从试样提取的精密度、稳定性、图谱重复性等方面均符合《中药注射剂指纹图谱研究的技术要求(暂行)》中的有关规定. 该方法具有重现性好, 特征性强, 方法简便、快速等特点, 有可能成为淫羊藿药材种属判断、质量评估的标准, 也会对未来开发淫羊藿中其他有效成分提供科学的依据.     

复合有机底物化学振荡体系的中药非线性电化学指纹图谱研究

本文提出了BrO3-Ce4+-H2SO4-丙二酸/苹果酸复合有机底物化学振荡体系,并将其用于研究中药的电化学指纹图谱.考察了振荡体系中各组分的浓度、温度、中药加入量、浸泡时间等因素对振荡图谱特异性的影响,确定了最佳组成及测试条件.研究结果表明,非线性电化学指纹图谱可用于鉴别和评价中药的真伪、药效、道地性等.该方法快速、...     

超高效合相色谱法定性与定量分析补肾健脑颗粒

用超高效合相色谱法(Ultra performance convergence chromatography,UPC2)建立补肾健脑颗粒及各药材提取物的指纹图谱,对补肾健脑颗粒主要色谱峰进行归属分析,并测定有效成分β-蜕皮甾酮和松果菊苷的含量。样品经乙醇提取后,进样1μL,用Waters ACQUITY UPC2TMBEH柱(100 mm×3.0 mm,1.7μm)分离,柱温为40℃,以超临界CO2-0.05%H3PO4-甲醇溶液为流动相,梯度洗脱,流速为0.8 m L/min。分析补肾健脑颗粒和各药材提取物的UPC2指纹图谱,利用各峰相对保留时间、紫外光谱图及部分对照品归属主峰。结果表明,补肾健脑颗粒UPC2指纹图谱中15个主峰来源明确,其中12号峰为β-蜕皮甾酮,含量为380μg/g,15号峰为松果菊苷,含量为9.562 mg/g。与HPLC和UPLC法相比,本方法简便、快速,精密度高,重现性好。     

不同提取方法的普洱茶气相色谱指纹图谱研究

以市售的普通茶和大益普洱茶为材料,采用气相色谱法(GC)对不同提取方法(索氏提取、微波提取、匀浆提取和超声提取)和不同溶剂(水、乙醇、丙酮、乙酸乙酯和石油醚)提取的提取液进行检测.对所得的GC指纹图谱进行整体性比较,最终建立一种简捷、整体性强、灵敏度高和分析时间短的普洱茶GC指纹图谱分析方法.     

高效液相色谱指纹图谱在地黄研究中的应用(Ⅰ)

长期以来,中药有效成分的提取分离和质量控制一直是中药产业中特有和尚未很好解决的问题.随着天然产物化学和现代仪器分析技术等相关学科的迅速发展,国内外在植物药及其制剂质量控制研究方面的重点均已转向利用各种仪器进行品质评价方面.中药来源于自然,其化学成分的多样性和复杂性是中药发挥其疗效的物质基础,同时也是质量评价与控制的重点与难点.中药的化学成分复杂,所体现的是综合效应和整体疗效.然而多年以来在中药的研究靠中,采取了与化学药品相同的研究思路,结果将药材及制剂内部各成分的综合作用和相互关系彼此孤立.在中药材及复方制剂质量标准的研究制定中,也往往是采用各种分析检测手段测定其中某种有效成分,并以其含量多少来判断比较某种药材的质量.这种质量控制模式很难做到全面衡量中药及其制剂的质量、疗效和稳定性.单一成分含量达标并不能说明该中药材质量合格.指纹图谱质量控制模式能综合反映某一特定药材各主要组分及其相对含量.因此它比测定任何一种或几种成分所提供的信息都丰富和有用的多.中药提取物在给定的实验条件下所得到色谱指纹图谱反映了该中药的化学组成及其含量分布状况,其特征峰可作为鉴别中药的依据.本文研究结果表明,利用色谱指纹图谱的相关参数来对中药原药材的质量进行控制,进而使中成药的质量得到保证,此方法的运用是切实可行的.另外,在有效成分不明确的前提下,利用色谱指纹图谱来评价中药的质量是有其意义的.色谱指纹图谱作为控制中药质量的新手段将在推进中药现代化进程上起到积极的作用.本文利用高效液相色谱建立了地黄的色谱指纹图谱.采用反相C18柱(5μm,150 mm×4.6 mm)、流动相甲醇:水(V/V=5:95)、检测波长为280 nm、流速1.0 mL/min进行试验.根据相对保留值和相对面积值对色谱指纹图谱进行分析对比研究,建立了控制地黄药材质量的新方法.该法为中药样品的鉴定提供了较全面的信息.     

加速溶剂提取-高效液相色谱法测定甘草中甘草酸的含量

采用加速溶剂提取法(ASE)提取甘草中有效成分甘草酸,高效液相色谱(HPLC)法测定其含量,探索ASE法提取甘草酸的最佳工艺条件,寻找一种快速、高效测定甘草中甘草酸含量的新方法.结果表明,ASE法提取甘草酸的最佳工艺条件为:提取温度为60℃,提取3次,每次静态提取时间为15 min,提取率高达2.15%.ASE-HPLC法是一种准确、快速测定甘草酸含量的新方法.     

不同工艺的荔枝核提取物抗氧化活性的比较

分别采用回流提取、热浸提取、微波辅助提取法分离荔枝核活性成分,测定了不同工艺制备的荔枝核提取物抑制油脂氧化以及清除羟基自由基和超氧阴离子自由基的抗氧化活性.结果表明,荔枝核提取物具有较强的抗氧化活性,能够有效地抑制油脂氧化;不同工艺的提取物对油脂抗氧化作用的排序为微波提取物热浸提取物回流提取物.与此同时,荔枝核提取物能够有效地清除羟基自由基,其中微波提取物的半清除率质量浓度(EC50)约为0.76 g/L,热浸提取物的EC50约为0.94 g/L,回流提取物的EC50约为2.0 g/L.此外,荔枝核提取物对超氧阴离子自由基也有一定的清除效果.     

红茶提取液在盐酸中对碳钢的缓蚀作用

采用动电位极化曲线和交流阻抗（EIS）研究了红茶提取液（BLE）在盐酸介质中对碳钢的缓蚀性能和缓蚀机理。 研究结果表明,采用索氏提取法从红茶茶叶中提取的缓蚀剂,对碳钢在1.0 mol/L盐酸溶液中具有良好的缓蚀性能,随着提取物浓度的增加,缓蚀效率增大。 红茶提取液中的有效缓蚀成分为抑制阴阳极反应的混合型缓蚀剂,在碳钢表面的吸附符合Langmuir等温式,属于单分子层吸附。     

Electrochemical Co-reduction of Bi(Ⅲ)and Y(Ⅲ)and Extracting Yttrium from Molten LiCl-KCl Using Liquid Bi as Cathode

The electrochemical reaction of Bi(Ⅲ)and co-reduction behaviour of Bi(Ⅲ)and Y(Ⅲ)ions were researched in molten LiCl-KCl on a ttmgsten(W)electrode employing a range of electrochemical teclmiques.Cyclic voltammetric and square-wave voltanunetric results revealed that the reduction of Bi(Ⅲ)was a one-step process,with the exchange of three electrons on a W electrode,and diffusion-controlled.The electrochemical curves showed two reduction peaks pertaining to the formation of Bi-Y alloy compounds,because of the co-reduction of Bi(Ⅲ)and Y(Ⅲ) by metallic Y deposited on the pre-deposited Bi-coated W electrode and reacting with Bi metal in molten LiCl-KCl. Furthermore,galvanostatic electrolysis was conducted using liquid Bi as cathode to extract yttrium at different current intensities,and the extractive products were analyzed by SEM,EDS and XRD.The results indicated that BiY intermetallic compotmd was formed in the molten LiCl-KCl-YCl3 system.     

Microwave-Assisted and Conventional Extractions of Volatile Compounds from Rosa x damascena Mill. Fresh Petals for Cosmetic Applications

Rosa x damascena Mill. essential oil is mainly used in the cosmetics and perfumery industry, but it also finds application in the food industry as a flavoring agent. The chemical composition of essential oils is affected by environment, soil, harvesting technique, storage condition, and extraction methods. Nowadays, the study and design of greener, more efficient, and sustainable extractive procedures is the main and strategic focus in the chemical research and development of botanical derivatives, especially as regards fragrances and essential oils. Several technologies are available, and the best method to use depends on the desired chemicals, but conventional extractive processes are often laborious and time-consuming, involve large amounts of solvents, and may cause the partial loss of volatiles, affecting the quality of the final product. In the last decade, microwave irradiation has been successfully applied to classical techniques, often improving the general extractive efficiency and extract quality. In the present paper, as a preliminary analytical screening approach, two microwave-mediated techniques, Solvent-Free Microwave Extraction (SFME) and Microwave Hydrodiffusion and Gravity (MHG), and two conventional procedures, Hydrodistillation (HD) and Steam Distillation (SD), were applied and compared for the extraction of volatile compounds from R. x damascena fresh petals to highlight differences and advantages of the selected procedure and of the obtained extracts useful in a cosmetic context as fragrances or active ingredients. The chemical composition of the extracts was investigated by GC-MS and GC-FID. Sixty-one components, distributed in the four techniques, were identified. SD and HD are dominated by oxygenated terpenes (59.01% and 50.06%, respectively), while MHG and SFME extracts are dominated by alcohols (61.67% and 46.81%, respectively). A relevant variability in the composition of the extracts relating to the extraction techniques used was observed. To point out the correlation between the process and composition of the obtained natural products, principal component analysis (PCA) of the data extracted from GC-FID was used. Taking into account a cosmetic application, SFME shows several advantages when compared with the other procedures. The extract (obtained in a significantly higher amount) contains a meaningful lower level of potential fragrance allergenic compounds and quite a double amount of benzyl alcohol and 2-phenyl ethanol that can also enhance the preservative action in personal care products.     

Electrochemical Energy Storage Electrodes via Citrus Fruits Derived Carbon: A Minireview

This review investigates the synthesis and electrochemical performance of the electrode of the electrochemical energy storage (EES) devices obtained from peels and scraps of the citrus fruits. The EES devices include batteries, supercapacitors, and hybrid systems that have considerable value and various applications. The electrode is considered as the most important part of all EES devices. Tremendous efforts have been done to enhance the electrochemical energy storage electrode (EESE). The citrus fruits abundance leads to a decrease in their price and makes possible to use them as ingredients to fabricate EESE. Also, the electrochemical analyses determined that citrus fruits have considerable potential to use as the EESE. Using citrus fruits peels and scraps as biomass substances to prepare EESE leads to the electrodes which have low cost, environmentally friendly and appropriate electrochemical applications.     

Trace analysis of anionic surfactants in mineral waters and soft drinks by spectrophotometry

The applicability of the extractive spectrophotometric method using Ethyl Violet as the chromogenic reagent for identification and quantification of anionic surfactants in different types of mineralized drinking waters, as well as in some non-alcoholic beverages, was investigated. The matrix-analyte interactions of major water constituents and soft-drink ingredients in the combinations and concentration ranges met in practice were studied individually. The method was evaluated by performing recovery tests on commercial and natural samples, with sodium dodecyl sulphate added as a model surfactant. The recoveries at the 57.6 and 86.4 g/l levels ranged from 98% to 104%.     

Foreword

Electrochemical behaviors of U⁴⁺ in LiCl–KCl–UF₄ eutectic and deposition of U metal were investigated. It was found that the presence of F^? has influence on the diffusion of U³⁺ and U⁴⁺ as comparing to data obtained in pure chloride molten salts. Electrochemical deposition of U was carried out by using pulse current electrolysis. Characterization results indicate that U metal was obtained at the cathode, implying U metal can be directly deposited from LiCl–KCl–UF₄ eutectic in this case and the extractive ratio is calculated to be 98%. Our results demonstrate feasible separation of U from LiCl–KCl–UF₄ molten salt by electrochemical method.     

Sulfanyl Porphyrazines with Morpholinylethyl Periphery—Synthesis,Electrochemistry, and Photocatalytic Studies after Deposition on Titanium(IV) Oxide P25 Nanoparticles

The syntheses, spectral UV–Vis, NMR, and electrochemical as well as photocatalytic properties of novel magnesium(II) and zinc(II) symmetrical sulfanyl porphyrazines with 2-(morpholin-4-yl)ethylsulfanyl peripheral substituents are presented. Both porphyrazine derivatives were synthesized in cyclotetramerization reactions and subsequently embedded on the surface of commercially available P25 titanium(IV) oxide nanoparticles. The obtained macrocyclic compounds were broadly characterized by ESI MS spectrometry, 1D and 2D NMR techniques, UV–Vis spectroscopy, and subjected to electrochemical studies. Both hybrid materials, consisting of porphyrazine derivatives embedded on the titanium(IV) oxide nanoparticles’ surface, were characterized in terms of particle size and distribution. Next, they were subjected to photocatalytic studies with 1,3-diphenylisobenzofuran, a known singlet oxygen quencher. The applicability of the obtained hybrid material consisting of titanium(IV) oxide P25 nanoparticles and magnesium(II) porphyrazine derivative was assessed in photocatalytic studies with selected active pharmaceutical ingredients, such as diclofenac sodium salt and ibuprofen.     

Perspectives of carbon paste electrodes in stripping potentiometry.

The testing of various types of carbon paste electrodes (CPEs) for their use in stripping potentiometry was carried out by means of specially proposed procedures and by using various model analyte systems. CPEs containing three different pasting liquids (paraffin oil, silicone oil, tricresyl phosphate) were tested as supports for mercury- and gold films, and as substrates for electrolytic, adsorptive, ion-pair forming, and extractive accumulation. Test measurements in organic solvent-containing media and studies of some irreversible electrochemical reactions were performed as well. Individual examples to be studied allowed one to formulate and outline some perspectives of CPEs in potentiometric stripping analysis and related constant current stripping analysis.