外围为柔性链状取代基团Ni-酞菁配合物的合成及其在MCM-41中的装载

合成了外围具有柔性链状基团的2（3）,9（10）,16（17）,23（24）-四-（N,N-二乙胺基乙氧基）Ni-酞菁配合物（2）．以正硅酸乙酯为硅源,十六烷基三甲基溴化铵为模板剂,水热法将该Ni-酞菁配合物（2）装载到MCM-41中．利用UV-Vis-NIR,FT-IR,XRD,TEM,FESEM及N2吸附-脱附等温线对制备的样品进行了表征．研究表明制备的样品中Ni-酞菁配合物（2）主要以单体和二聚体的形式存在于MCM-41中．通过不同制备酞菁浓度的装载研究表明,较高制备酞菁浓度有利于制备结晶度及孔道有序性较高的介孔分子筛样品．     

MCM-41分子筛的改性、表面结构与吸附性质的研究

用三甲基氯硅烷、二甲基二氯硅烷、甲基三氯硅烷、四氯化硅与甲基碘改性高硅MCM-41中孔分子筛。XRD,^2^9SiMASNMR,^1^3CMASNMR,以及N~2、水与环己烷吸附的表征,显示改性不同程度地改变了分子筛的表面组成与结构,减小孔径,增加孔壁厚度,因而影响吸附行为,减小吸附容量。硅烷化减少了MCM-41的表面硅羟基含量,增加其疏水性。用CH~3I改性使孔径减小1.4nm,而硅羟基含量并未显著减少。硅烷化以及用CH~3I改性可提高MCM-41分子筛的热稳定性。SiCl~4的改性作用相对不明显。样品的水及环己烷吸附容量与其表面硅羟基含量呈现不同的线性关系,揭示高硅MCM-41分子筛表面吸附中心的本性。     

表面活性剂修饰对MCM-41负载离子液体吸附CO2影响的研究

以表面活性剂修饰的MCM-41为载体,采用浸渍法制备了负载离子液体[NH2p-mim][PF6]的二氧化碳吸附剂,考察了表面活性剂对离子液体在MCM-41上分散的影响以及所导致的CO2吸附性能的变化.利用红外光谱(FT-IR),X-射线衍射(XRD),高分辨透射电子显微镜(HRTEM),热重分析(TG)技术对所合成的负载型离子液体吸附剂进行了表征研究,并与其吸附CO2的性能变化、离子液体与表面活性剂相互作用方式等因素进行了关联.结果表明:MCM-41负载离子液体后对CO2的吸附性能略有提高,而经表面活性剂修饰的MCM-41负载离子液体后,对CO2的吸附容量较载体本身提高了2.5倍.这一方面是因为表面活性剂胶束改善了MCM-41上离子液体的分散性,另一方面是表面活性剂胶束对离子液体分子上电荷分布的影响,导致离子液体内部阴阳离子之间的相互作用减弱,从而引起离子液体中-NH2上N原子电子云密度增大,使其与CO2作用更容易.CO2在经表面活性剂修饰后的MCM-41负载离子液体[NH2p-mim][PF6]吸附剂上的吸附受扩散控制,其吸附-脱附CO2所需能量较小,经过5次吸附-脱附循环后,其吸附性能仍保持稳定.热重分析结果表明,经表面活性剂修饰后的MCM-41负载离子液体吸附剂在100℃下氮气气氛再生时不会发生性质改变.     

Epoxidation of cyclohexene on modified Ti-containing mesoporous MCM-41

Ti-MCM-41, B-Ti-MCM-41 and Ti-grafted MCM-41 were synthesized, characterized and studied in the epoxidation of cyclohexene. The synthetic methods and the effect of water in the oxidant are discussed.     

Cr/MCM-41催化剂的结构特征及其纳米尺寸孔内聚乙烯的形成

合成了纯硅MCM-41,并以浸渍法在表面负载烯烃聚合催化活性中心---过渡金属元素Cr;通过对所得Cr/MCM-41样品的结构特征及Cr物种的存在形成进行XRD,低温N2吸附,FTIR,Raman,^2^9SiNMR等表征发现,Cr/MCM-41具有良好的长程有序结构、较高的比表面积及均一的孔径分布。负载于MCM-41表面的Cr物种通过与羟基的相互作用分散于载体孔道内。Cr负载量较低时,Cr物种主要以孤立态存在,随着Cr含量增加,出现聚合态的Cr物种。Cr/MCM-41的一维孔道内,不仅可进行乙烯的聚合形成聚乙烯,而且反应后MCM-41的长程结构保持不变。     

青霉素酰化酶在介孔分子筛MCM-41上的固定化研究

通过改变酶固定化时的pH值、温度、时间以及酶用量,研究了固定化条件对MCM-41载体上固定化青霉素酰化酶的酶活及其稳定性的影响,明确了酶活及其稳定性随固定化条件的变化规律,初步分析了青霉素酰化酶在介孔分子筛MCM-41上的固定化过程。     

Synthesis, characterization, and catalytic properties of stable mesoporous molecular sieve MCM-41 prepared from zeolite mordenite

Mesoporous molecular sieves (denoted as M-MCM-41) with ordered hexagonal structure have been successfully synthesized from the assembly of precursors from preformed zeolite Mordenite with CTAB surfactant micelle in alkaline media. The samples were characterized by XRD, N₂ adsorption, IR and DTG. The materials exhibit highly hydrothermal stability, as compared with conventional MCM-41. Characterization results indicate that the mesoporous walls of M-MCM-41 contain the secondary building units similar to those in microporous crystal of zeolite Mordenite. In catalytic dealkylation of C10⁺ aromatic hydrocarbon, M-MCM-41 shows higher activities in comparison with Mordenite and MCM-41, which would be ascribed to the combination of advantages of both MCM-41 (large pores) and Mordenite (strong acidity). Furthermore, this synthesis strategy could be used as a new general method for the preparation of hydrothermally stable mesoporous aluminosilicate materials under alkaline conditions.     

苯基化纳米MCM-41材料的制备与表征

以苯基三甲氧基硅烷为偶联剂对纳米MCM-41分子筛进行了有机改性,制备了苯基改性的纳米MCM-41分子筛MCM-41(m)。利用元素分析、粉末XRD、傅里叶变换红外光谱、氮气吸附-解吸附、扫描电镜和差热-热重分析对制备产物进行了表征。粉末XRD结果表明,改性过程中,分子筛骨架未被破坏,并且所制备MCM-41(m)分子筛结晶度依然很高;傅里叶变换红外光谱表明苯官能团已经成功地接枝到了分子筛的孔道表面,且所得产物的骨架依然完好;低温氮气吸附-解吸附分析结果表明,MCM-41(m)分子筛孔道具有高度有序性,改性的纳米MCM-41分子筛孔道内的硅羟基与苯基三甲氧基硅烷发生了硅烷化反应,苯基成功地接枝到了分子筛的孔道表面。扫描电镜结果表明, 制得的苯基改性纳米MCM-41平均尺寸为110 nm。差热-热重分析结果说明了所制备的苯基化的纳米MCM-41样品具有良好的热稳定性,骨架稳定温度为823 ℃。苯基化的纳米MCM-41材料具有作为催化剂材料的潜在应用前景。     

Hydrogenation of naphthalene on noble-metal-containing mesoporous MCM-41 aluminosilicates

Aromatic saturation of oil fractions is a key process in the refining industry due to increasing demand for cleanest distillates with superior performances. In this study, the behavior of different catalysts containing 1 wt.% of noble-metal inside a mesoporous MCM-41 (Si:Al=20) framework was investigated in the hydrogenation of naphthalene, as preliminary step to investigate bimetallic catalysts. While at atmospheric pressure only Rh and Pd showed a low hydrogenation activity, in the tests performed at 6.0 MPa the catalytic activity grew, exhibiting the following order: Pt>RhPd>>>Ru≈Ir. However, all the catalysts required a large H₂ excess, to avoid a decrease in hydrogenation and ring-opening activity, and gave rise to the best performance for a contact time of 6.8 s, favouring at lower values the partial hydrogenation to tetralin and at higher values cracking reactions. Finally, all the catalysts showed low thio-tolerance, with significant deactivation already feeding 100 ppm wt. of dibenzothiophene (DBT), with a partial reversibility only for the Pt-containing catalyst (CAT 3).     

Synthesis, characterization and optical properties of silver and gold nanowires embedded in mesoporous MCM-41

Uniform nanowires of silver and gold inside the channels of MCM-41 were prepared by controlled reduction of their respective metal salts with sodium borohydride (NaBH₄). Presence of nanowires of silver and gold in MCM-41 were confirmed by high angle X-ray diffraction (XRD) data (peaks between 2ϑ = 30 − 60°) and transmission electron microscopy (TEM) confirmed the diameter of the nanowires. Diameter of nanowires is found to be ∼ 2.8 nm which is coincident with channel diameter of MCM-41. Optical properties of these heterostructured materials Ag-MCM-41 and Au-MCM-41 reveals the presence of surface plasmon absorption peaks of silver and gold respectively, and the shift in the absorption bands are associated to agglomeration of clusters inside the channels. Room temperature photoluminescence spectra exhibits interesting optical properties as observed for direct band gap semiconductors. Non-linear optical properties (NLO) corresponding to second harmonic generation (SHG) values were also recorded for self supported films of these heterostructured materials. Enhanced optical non-linearity was found to be arising from a corresponding increase of local field near the surface plasmon resonance. Further enhancement in SHG was found with poling due to an induction of orientation order.     

Synthesis of Thermally Stable MCM-41 at Ambient Temperature

A new process to synthesize thermally stable mesoporous molecular sieves of MCM-41 structure based on delayed neutralization at ambient temperature was investigated. All samples synthesized by this new method have BET surface areas of about 1100m²/g and possess high thermal stability up to 900°C. Higher crystallinity and less lattice constriction after calcination were observed for samples with a longer aging period. Those samples with aging time longer than 10 days exhibited four characteristic XRD peaks of MCM-41 both before and after calcination at 560°C. The N₂ adsorption-desorption isotherms of the calcined samples showed larger average pore size and more homogenous pore size distribution. The method was also successfully applied to the synthesis of MCM-41 with different surfactants of hydrocarbon length with 10–18 carbons and proves to be a simple route for obtaining thermally stable MCM-41 at room temperature.     

The Synthesis and Characteristics of Vanadoaluminosilicate MCM-41 Mesoporous Molecular Sieves

A series of vanadoaluminosilicate MCM-41 mesoporous molecular sieves with various compositions have been hydrothermally synthesized. Hexadecyltrimethylammonium bromide was used as a surfactant in the synthesis. The samples were characterized with nitrogen sorption, X-ray diffraction, differential thermal analysis, thermogravimetric analysis, Fourier transform-Infrared spectroscopy, UV-visible spectroscopy, scanning electron microscopy, transmission electron microscopy, and solid state NMR. The solid products had the MCM-41 structure and contained only atomically dispersed vanadium and aluminum consistent with framework vanadium and aluminum. The samples were hydrophobic and contained large amount of surfactant in the as-synthesized samples. The surfactant could be removed upon calcination at 450°C. N₂ sorption measurements and TEM demonstrate the high mesoporosity of [V, Al]-MCM-41. The incorporation of vanadium and aluminum into MCM-41 decreased the surface area to some extent. The morphologies of all the samples were the agglomerate of plates. ²⁹Si MAS NMR shows that the pore wall is amorphous. ²⁷Al MAS NMR shows that all of aluminum species were tetrahedrally coordinated even after calcination at 550°C.     

MCM-41分子筛合成与模版剂回收新方法

研究了以溴代十六烷基吡啶（CPBr）为模板剂,正硅酸乙酯（TEOS）为硅源,在强酸性介质中形成MCM-41介孔分子筛六方晶相的过程中,HCI／TEOS对分子筛结构的影响．发现随HCI／TEOS提高,分子筛结晶度、晶胞参数、孔道壁厚明显增加,孔径呈减少趋势．同时还发现包结于分子筛孔道中的CPBr100％可以通过丙团／水混合溶剂萃取回收．据此,本文对MCM-41分子筛的“S X-I ”超分子组装机理及分子筛孔道内模板剂的存在状态进行了进一步探讨．     

Ni-Fe-B/MCM-41非晶态合金的合成与表征

用化学还原沉积法制备了Ni-Fe-B／MCM-41负载型非品态合金催化材料。通过XRD,FT-IR,TPR,SEM,TG及BET研究了非晶态合金对介孔分子筛载体结构的影响及非晶态合金负载后性质和形态的变化。结果表明：非晶态合金没有破坏介孔分子筛的结构,Ni-Fe-B／MCM-41的热稳定性和氧化能力与Ni-Fe-B相比,均有一定提高。     

磺酸基功能化MCM-41有机-无机杂化材料的合成与表征

 利用直接合成法和后接枝法将含有磺酸基团的硅烷偶联剂引入MCM-41介孔分子筛中, 合成了酸性介孔有机-无机杂化材料. 利用XRD和TEM等方法对其结构进行了表征. 结果表明,利用直接合成法和后接枝法合成的杂化材料仍保持规整的介孔孔道,该材料作为酸催化剂在苯甲醛与乙二醇的缩醛反应中显示了较好的催化活性.     

Synthesis, characterization, and near-infrared luminescent properties of the ternary thulium complex covalently bonded to mesoporous MCM-41

The crystal structure of a ternary Tm(DBM)₃phen complex (DBM=dibenzoylmethane; phen=1, 10-phenanthroline) and the synthesis of hybrid mesoporous material in which the complex covalently bonded to mesoporous MCM-41 are reported. Crystal data: Tm(DBM)₃phen C₅₉H₄₇N₂O₇Tm, monoclinic, P21/c, a=19.3216(12) Å, b=10.6691(7) Å, c=23.0165(15) Å, α=90°, β=91.6330(10)°, γ=90°, V=4742.8(5) Å³, Z=4. The properties of the Tm(DBM)₃phen complex and the corresponding hybrid mesoporous material [Tm(DBM)₃phen-MCM-41] have been studied. The results reveal that the Tm(DBM)₃phen complex is successfully covalently bonded to MCM-41. Both Tm(DBM)₃phen complex and Tm(DBM)₃phen-MCM-41 display typical near-infrared (NIR) luminescence upon excitation at the maximum absorption of the ligands, which contributes to the efficient energy transfer from the ligands to the Tm³⁺ ion, an antenna effect. The full width at half maximum (FWHM) centered at 1474 nm in the emission spectrum of Tm(DBM)₃phen-MCM-41 is 110 nm, which is the potential candidate of broadening amplification band from C band (1530-1560 nm) to S⁺ band (1450-1480 nm) in optical area.     

中孔分子筛MCM-41形成机理的考察

MCM－41分子筛是九十年代初期美国Mobil公司开发的一种新型中孔（mesoporous）材料[1]．它以C8－C16季俊碱表面活性剂作为模板剂水热法合成，具有2－10nm的孔径，孔道六方有序排列，高比表面和高吸附容量，中等酸性和稳定性，是一种有潜在应用前景的吸附和催化材料．目前，关于     

以混合表面活性剂为模板可控合成MCM-48和MCM-41分子筛

利用阳离子和三嵌段共聚物混合表面活性剂为模板,在水热条件、碱性介质中可控合成出MCM-48和MCM-41分子筛。在固定P123(聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物):TEOS(正硅酸乙酯)(物质的量的比)为0.01875的体系中,调节CTAB(十六烷基三甲基溴化铵)∶TEOS(正硅酸乙酯)物质的量比值m,当m在0.12~0.13范围合成出MCM-48分子筛;当m在0.04~0.08范围合成出MCM-41分子筛。通过XRD,TEM,N2物理吸附,IR等方法进行了表征。结果表明:聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物(P123)的加入可以更大程度地降低合成介孔材料所需阳离子表面活性剂的用量;可控合成的介孔材料具有高比表面积、高度有序的孔道结构、较集中的孔径分布。     

TiO~2修饰的介孔分子筛MCM-41的合成、表征及光 催化性研究

首次以三种不同的含钛有机物为氧化钛的前驱体,合成了三种TiO~2呈单层分散状态的TiO~2修饰的介孔分子筛MCM-41,并以XRD,FT-IR,液氮温度下N~2吸附-脱附曲线,固体UV-vis漫反射等表征手段对其结构特征和氧化钛分散状态进行了研究。TiO~2在介孔分子筛MCM-41孔道中分散,MCM-41仍能保持骨架结构,没有晶相TiO~2生成;TiO~2与MCM-41孔道表面的≡Si－OH以化学键连接,生成Si－O－Ti键;TiO~2在MCM-41内孔壁呈均匀单层分散状态;TiO~2粒子的减小使其对紫外光的吸收发生明显的蓝移现象。并以苯酚降解反应为模型检验合成的具有光催化性的TiO~2修饰的MCM-41的光催化活性。     

ZSM-5/MCM-41复合分子筛的合成与表征

以碱处理的ZSM-5浆液为硅铝源,通过水热自组装过程合成了介孔-微孔复合孔道结构的分子筛,并采用XRD、BET、HRTEM、Py-IR和水热处理等手段对合成分子筛进行了表征。结果表明,碱处理ZSM-5时的苛刻程度是影响复合分子筛合成的重要因素,适宜的碱处理条件为NaOH浓度1 mol/L、80℃时处理1 h。表征结果表明,复合分子筛具有规整互通的微孔-介孔梯级复合孔道结构,孔容、比表面积和平均孔径分别为0.63 mL/g,684 m²/g和3.76 nm,属典型的MCM-41结构;与MCM-41相比,复合分子筛的B酸(尤其是强B酸)酸量明显增强,水热稳定性显著提高。