Synthesis and characterization of the water-soluble silica-coated ZnS:Mn nanoparticles as fluorescent sensor for Cu ions

Silica-coated ZnS:Mn nanoparticles were synthesized by coating hydrophobic ZnS:Mn nanoparticles with silica shell through microemulsion. The core–shell structural nanoparticles were confirmed by X-ray diffraction (XRD) patterns, high-resolution transmission electron microscope (HRTEM) images and energy dispersive spectroscopy (EDS) measurements. Results show that each core–shell nanoparticle contains single ZnS:Mn nanoparticle within monodisperse silica nanospheres (40 nm). Photoluminescence (PL) spectroscopy and UV–vis spectrum were used to investigate the optical properties of the nanoparticles. Compared to uncoated ZnS:Mn nanoparticles, the silica-coated ZnS:Mn nanoparticles have the improved PL intensity as well as good photostability. The obtained silica-coated ZnS:Mn nanoparticles are water-soluble and have fluorescence sensitivity to Cu²⁺ ions. Quenching of fluorescence intensity of the silica-coated nanoparticles allows the detection of Cu²⁺ concentrations as low as 7.3 × 10⁻⁹ mol L⁻¹, thus affording a very sensitive detection system for this chemical species. The possible quenching mechanism is discussed.     

Optical and Structural Properties of Doped ZnS Nanoparticles Produced by the Sol-Gel Method

Optical and structural properties of Mn2+-doped ZnS nanoparticles in an organic matrix are experimentally and theoretically studied. The nanoparticles, which were produced by the sol-gel method, are nearly monodisperse with a diameter of approximately 3 nm and show the characteristic orange-red luminescence of Mn2+ centers in a crystalline ZnS matrix. The absorption spectrum of the embedded ZnS nanoparticles is slightly blue shifted and broadened compared to the reference system containing ZnS microparticles. This blue shift is caused by quantum size effects, whereas the broadening is due to defects such as lattice distortions, and vacancies, which are probably located close to the surface in the case of small particles. With increasing temperature the absorption spectra shift to the red and are broadened due to thermal activated diffusion of ions close to the surface. In contrast, the spectral feature of the emission spectra via the Mn2+ center is nearly unchanged compared to the ZnS microparticles. Furthermore, the quantum efficiency is increased and the decay time of the electron-hole pairs is shortened to the nanosecond regime because of the enhanced probability of the electron-hole pairs to see the Mn2+ center. Therefore, the only effect of doping of ZnS nanoparticles with Mn2+ center is the suppression of the relaxation of electron-hole pairs via surface defects generating a highly efficient and fast relaxation of the electron-hole pairs via the Mn2+ center.     

硫化锌掺锰/聚乙烯醇复合纳米纤维的制备与表征

利用静电纺丝法与气固反应相结合, 成功地制备了硫化锌掺锰/聚乙烯醇复合纳米纤维, 并对所制备的复合物进行了表征, 探讨了复合物的结构及其性能.     

ZnS纳米球的水热法制备及其光催化性能研究

在表面活性剂十六烷基三甲基溴化铵(CTAB)的辅助下,以乙酸锌为锌源,硫脲(NH2)2CS为硫源,使用水热法通过改变反应时间,成功制备了不同粒径的ZnS球状颗粒。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、X-射线能谱,高分辨透射电子显微镜(HRTEM))、紫外可见分光光谱和光致发光谱(PL)等测试手段对样品的晶体结构、形貌、光学性质进行了分析。通过对不同粒径的ZnS纳米颗粒对亚甲基蓝的光催化降解的催化活性进行了评估。实验结果表明:在表面活性剂CTAB的作用下,随着反应时间的增加,生成的ZnS晶核生长成纳米颗粒,然后ZnS纳米颗粒将进一步发生团聚从而形成平均粒径超过500nm的ZnS纳米球,但制备的ZnS产物的晶体结构均为立方纤锌矿结构。随着ZnS粒径的增加,样品的紫外吸收峰从418nm逐渐蓝移到362nm,而PL发射峰位的峰强随着粒径的增大而增强。光催化结果显示,反应12h制备的ZnS纳米球的光催化性能最佳。     

New observations on the luminescence decay lifetime of Mn2+ in Zns: Mn2+ nanoparticles

A fast decay emission peaking at 645 nm with a decay lifetime within the experimental resolution of 0.14 micros is observed in ZnS:Mn2+ nanoparticles. This short-lived signal is also observed in pure ZnS and MgS: Eu3+ nanoparticles, which has nothing to do with Mn(2+)-doped ions but is from the deep trap states of the host materials. The short-lived component decreases in intensity relative to the Mn2+ emission at higher excitation powers, while it increases in intensity at low temperatures and shifts to longer wavelengths at longer time delays. Our observations demonstrated further that the emission of Mn2+ in ZnS: Mn2+ nanoparticles behaves basically the same as in bulk ZnS: Mn2+; the fast decay component is actually from the intrinsic and defect-related emission in sulfide compounds.     

ZnS:Mn2+/聚苯乙烯核壳及ZnS:Mn2+中空球的制备和光谱性质

ZnS:Mn2+ polystyrene (PS) core-shell structures and ZnS:Mn2+ hollow spheres were prepared by a sonoehemical deposition approach. Transmission electron micrograph (TEM) studies show that the PS surface is covered by a thin shell consisted of ZnS: Mn2+ nanoparticles with an average size of 9 nm. ZnS: Mn2+ hollow spheres were obtained by heating the core-shell particles in air at 500 ℃ to drive off PS. The photoluminescence spectrum for the emission band of Mn2+ peaked at 540 nm, and a 45 nm blue shift compared to that of corresponding bulk sample, was discussed based on the Mn-O octahedral distortion induced by shell structure.     

Synthesis and characterization of high-quality ZnS, ZnS:Mn2+, and ZnS:Mn2+/ZnS (core/shell) luminescent nanocrystals

High-quality ZnS, ZnS:Mn2+, and ZnS:Mn2+/ZnS (core/shell) nanocrystals (NCs) were synthesized via a high-boiling solvent process and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), electron paramagnetic resonance (EPR), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectra. The monodisperse ZnS NCs (size = 8 nm), which self-assembled into several micrometer-sized domains, were achieved by adopting poly(ethylene glycol) (PEG) in the reaction process (without using a size-selection process). The obtained ZnS:Mn2+ and ZnS:Mn2+/ZnS core/shell NCs are highly crystalline and quasimonodisperse with an average particle size of 6.1 and 8.4 nm, respectively. All of the as-formed NCs can be well dispersed in hexane to form stable and clear colloidal solutions, which show strong visible emission (blue for ZnS and red-orange for ZnS:Mn2+ and ZnS:Mn2+/ZnS) under UV excitation. The growth of a ZnS shell on ZnS:Mn2+ NCs, that is, the formation of ZnS:Mn2+/ZnS core/shell NCs, resulted in a 30% enhancement in the PL intensity with respect to that of bare ZnS:Mn2+ NCs due to the elimination of the surface defects.     

A new solid-phase nanoparticle FRET assays based on GO/CS/ZnS nanocomposite film and developed in sensing for bromonium ion

Composite thin films consisting of nano-sized ZnS particles dispersed in chitosan/GO films have been prepared by in-situ method. The films obtained were characterized by FTIR and UV–Vis spectroscopy. The ZnS nanoparticles with 90 nm in diameter were dispersed uniformly in the film matrix. Optical absorption peak due to the size of ZnS particles was observed around 350 nm. The fluorescence emission at 430 nm of the GO/CS/ZnS nanocomposite films is very sensitive to the presence of bromonium ion from aqueous solutions. New solid-phase nanoparticles FRET assays are firstly immobilized on the substrate and then interacted with functionalized acceptor molecules in the solution to trigger the FRET effect to detect Br^–.     

Synthesis and spectroscopic investigations of Cu- and Pb-doped colloidal ZnS nanocrystals

A novel organometallic synthesis method for the preparation of colloidal ZnS nanoparticles is presented. This method enables the synthesis of undoped ZnS nanocrystals as well as doping with Cu, Pb, or both. The particles can be covered with an undoped layer of ZnS, forming core/shell-type particles with the ZnS:Pb, ZnS:Cu, or ZnS:Cu,Pb cores. The particles were characterized via TEM, XRD, dynamic light scattering, and optical spectroscopy. We investigated the extrinsic surface defects and their coverage with an additional ZnS layer in detail by temperature-dependent luminescence and luminescence lifetime spectroscopy.     

Synthesis and Spectral-Luminescent Properties of Zinc Sulfide Nanoparticles in a Perfluorosulfonic Membrane

Zinc sulfide nanoparticles were synthesized in pores of a perfluorosulfonic membrane by ion exchange fixation of Zn²⁺ cations followed by the processing with gaseous hydrogen sulfide. Resulting ZnS particles are X-ray amorphous, have a low density, and are clearly expressed in absorption and luminescence spectra. Features of the nanoparticles optical properties were considered in light of electrons photoexcitation on antibonding orbitals (Zn–S)*.

     

Photoluminescence Properties of Surface-Modified Nanocrystalline ZnS : Mn

DBS surface-modified nanocrystalline ZnS : Mn was prepared by a precipitation method. Photoluminescence spectra and decay curves were measured and compared to those of unmodified samples. For both kinds of samples, luminescence decay curves of 600 nm emission consist of two components with nanosecond (ns) and millisecond (ms) lifetimes. The nanosecond component is attributed to zinc vacancies luminescence, with peak located at 440 nm. While the millisecond component is attributed to Mn(2+) luminescence and its decay time changes with Mn(2+) concentration and surface modification. The surface-modified sample has a longer lifetime compared to unmodified samples. The photoaging of surface-modified samples is slow. Particle size effects on photoaging were also examined. For nanocrystalline ZnS : Mn photoaging is more noticeable than that of bulk material. After UV irradiation, photoluminescence intensity of the modified sample is several times larger than that of the unmodified sample, because the surface-active reagent decreases surface defects and depresses radiationless transitions. XPS yields direct evidence of the surface-modification effect on the surface structure. Copyright 2000 Academic Press.     

Nanosilica-supported polyethoxyamines as low-cost, reversible carbon dioxide sorbents

Nanoparticles capped with amine ligands with different steric properties, dodecylamine and oleylamine, respectively, are investigated in the solid state as well as in solution. A combined X-ray diffraction, small angle X-ray scattering and electron microscopy investigation showed that the nanoparticles exhibit the sphalerite modification of ZnS as crystal phase with a diameter of 3-5 nm. A close packing of the monocrystalline nanoparticles in the solid state is observed. However, in the dodecylamine sample, besides spherical particles, a fraction of the nanoparticles is elongated. The nanoparticles are readily resoluble in apolar solvents like hexane. Dynamic light scattering (DLS) and SAXS investigations of the solutions reveal that the nanoparticles are dissolved as singular particles. In the case of oleylamine-capped ZnS, a defined core-shell structure with a ZnS core with a diameter of 4 nm and an organic shell with a thickness of approximately 2 nm have been found. Dodecylamine-capped nanoparticles slightly tend to form agglomerates with a diameter of approximately 40 nm.     

ZnS nanosheets: Egg albumin and microwave-assisted synthesis and optical properties

ZnS nanosheets were prepared via egg albumin and microwave-assisted method. The phases, crystalline lattice structures, morphologies, chemical and optical properties were characterized by X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM), field-emission scanning electron microscope(FE-SEM), selected area electron diffraction (SAED), Fourier transform infrared (FTIR) spectroscopy, ultraviolet–visible (UV–Vis) spectroscopy and fluorescence(FL) spectrometer and growth mechanism of ZnS nanosheets was investigated. The results showed that all samples were pure cubic zinc blende with polycrystalline structure. The width of ZnS nanosheets with a rectangular nanostructure was in the range of 450–750 nm. The chemical interaction existed between egg albumin molecules and ZnS nanoparticles via the amide/carboxylate group. The band gap value calculated was 3.72 eV. The band at around 440 nm was attributed to the sulfur vacancies of the ZnS nanosheets. With increasing volumes of egg albumin, the photoluminescence (PL) intensity of ZnS samples firstly increased and then decreased, attributed to concentration quenching.     

核壳结构CdS/ZnS纳米微粒的制备与光学特性

CdS and CdS/ZnS core-shell structure nano particles were synthesized in micro emulsion, and characterized by X-ray diffraction(XRD), transmission electron microscopy (TEM), UV absorption spectra and PL. The average diameter of CdS was about 3.3 nm, and CdS/ZnS core-shell structure was confirmed by XRD and UV. Considering the optical properties of CdS/ZnS core-shell structure nanoparticles which have different ZnS shell thickness, the UV absorption edge of CdS/ZnS becomes as lightred-shift with the thickness of ZnS layer increasing, and the absorption of shortwave band is strongly enhanced at the same time. The PL spectra indicate that ZnS shell layer can greatly eliminate surface defects of CdS nanoparticles and make its band-edge directed recombination increased, and the luminous efficiency of CdS is improved greatly when it has appropriate shell thickness.     

Effects of intensity and energy of CW UV light on the growth of gold nanorods

Growth of gold nanorods (AuNRs) by photochemical reduction of HAuCl4 in a micelle solution of hexadecyltrimethylammonium bromide (CTAB) and tetraoctylammonium bromide (TOAB) is studied. The effects of 300 and 254 nm UV light sources and their photon flux on the anisotropic growth of gold nanoparticles are investigated by controlling duration of irradiation and the number of lamps within a photochemical reactor. The resulting AuNRs were characterized by absorption spectroscopy, FTIR, and TEM. Experimental results indicate that a higher density of longer colloidal AuNRs form by increasing the number of incident photons (lamps) at 300 nm while the 254 nm lights produce a lower yield of shorter AuNRs. The yield of AuNRs also depends on the duration of irradiation which was found to be 6.00 h for 300 nm and 5.00 h for 254 nm radiation. Acetone is found to play a major role in the synthesis of AuNRs. Two mechanisms are proposed for the synthesis of Au nanoparticles in the presence and absence of acetone. Irradiation of samples for an excess time produces a lower concentration of AuNRs and a higher yield of spherical particles. This effect is attributed to atom-by-atom dissolution of AuNRs into Au-spherical particles.     

水溶液中Mn2+对硫化锌纳米粒子形貌的调控作用

利用硫代乙酰胺在水溶液中缓慢释放的S2-与Zn2+反应制备了ZnS纳米颗粒,ZnS纳米颗粒沉积吸附在3-磺酸基丙基三甲氧基硅烷自组装单层膜上。 实验发现,溶液中添加少量Mn2+,可以显著影响ZnS纳米颗粒的形貌,对ZnS纳米晶的生长方向也有重要影响。 EDS和XRD谱证实Mn2+并没有掺杂到纳米颗粒中去。 这为纳米粒子形貌的调控提供了新途径。 并对ZnS的形成过程进行了探讨,并提出了可能的影响纳米材料形貌的机制。     

Luminescence enhancement and potential application of sky-blue sulfide phosphor doped with promoter

The luminescence of the ZnS:Tm phosphor was enhanced by the addition of a KCl promoter, and a white phosphor was prepared for potential white-light applications. It was found that a high synthesis temperature and high TmF₃ concentration promoted the substitution of Tm³⁺ ions for Zn²⁺ ions. KCl doping facilitated the growth of the hexagonal phase and decreased the phase transformation temperature of ZnS. In addition, the luminescence center concentration, excitation energy absorption, effective energy transfer, charge balance, and luminescence intensity of the phosphor were improved by the addition of the KCl promoter. The emission pattern and peaks of the ZnS:Tm,KCl phosphor were similar to those of the ZnS:Tm phosphor, indicating that the ligand field variation of Tm³⁺ caused by KCl doping was small. When the sky-blue ZnS:Tm,KCl phosphor was blended with a yellow ZnS:Mn,KCl phosphor in 1:1 weight ratio, white-light emission was observed under excitation from a 6-W ultraviolet lamp (1,350 μW/cm², λ?=?254 nm). The Commission Internationale de l’Eclairage coordinates were (0.36, 0.35), and the luminance intensity was 28.1 cd/m².     

ZnS:Mn nanoparticles conjugated to sol–gel-derived silica matrices

Composites from ZnS:Mn nanoparticles and modified silicas are of interest for a broad range of potential applications in the form of films, structured particles, and self-assembled structures (e.g., colloidal crystals). They combine the versatility of silica sol gel chemistry with the wealth of functionalities available from doped nanoparticulate semiconductors (e.g., optical, electrical, and magnetic). In this work, ZnS:Mn nanoparticles have been prepared and modified in such a way that they can be incorporated seamlessly, either by inclusion or by covalent bonding into silicas. Functionalization was achieved through the use of silanes or thioles. Further processing by standard sol gel chemistry then either led directly to covalent conjugation with the silica network formed after condensation, or to isolated particles encapsulated in a silica shell. The results are heavily loaded (up to 30 wt%), transparent (including semiconductor particles that are smaller than 15 nm) and luminescent films, and massive bodies. In this work, the progress of nanocomposite formation was followed mainly by luminescence spectroscopy. Further work will have to address the electrical and magnetic properties of these nanocomposites as well.     

Phase structure and luminescence properties of Eu3+-doped TiO2 nanocrystals synthesized by Ar/O2 radio frequency thermal plasma oxidation of liquid precursor mists

Eu3+-doped TiO2 luminescent nanocrystals have been synthesized in this work via Ar/O2 thermal plasma oxidizing mists of liquid precursors containing titanium tetra-n-butoxide and europium(III) nitrate, with varied O2 input in the plasma sheath (10-90 L/min) and Eu3+ addition in the precursor solution (Eu/(Ti + Eu) = 0-5 atom%). The resultant nanopowders are mixtures of the anatase (30-36 nm) and rutile (64-83 nm) polymorphs in the studied range, but the rutile fraction increases steadily at a higher Eu3+ addition, as revealed by X-ray diffraction (XRD) and Raman spectroscopy, because of the creation of oxygen vacancies in the TiO2 gas clusters by substitutional Eu3+ doping. The amount of Eu3+ that can be doped into a TiO2 lattice was limited up to 0.5 atom%, above which Eu2Ti2O7 pyrochlore was formed in the final products. High resolution transmission electron microscopy (HRTEM) observation indicates that the particles are dense and have sizes ranging from several nanometers up to 180 nm. Efficient nonradiative energy transfer from the TiO2 host to Eu3+ ions, which was seldom reported in the wet-chemically derived nanoparticles or thin films of the current system, was confirmed by combined studies of excitation, UV-vis (ultraviolet-visible), and PL (photoluminescence) spectroscopy. As a consequence of this, bright red emissions were observed from the plasma-generated nanopowders either by exciting the TiO2 host with UV light shorter than 405 nm or by directly exciting Eu3+ at a wavelength beyond the absorption edge (405 nm) of TiO2.     

ZnS纳米球的水热法制备及其光催化性能研究

在表面活性剂十六烷基三甲基溴化铵(CTAB)的辅助下,以乙酸锌为锌源,硫脲(NH₂)₂CS为硫源,使用水热法通过改变反应时间,成功制备了不同粒径的ZnS球状颗粒.利用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线能谱,高分辨透射电子显微镜(HRTEM))、紫外可见分光光谱和光致发光谱(PL)等测试手段对样品的晶体结构、形貌、光学性质进行了分析.通过对不同粒径的ZnS纳米颗粒对亚甲基蓝的光催化降解的催化活性进行了评估.实验结果表明:在表面活性剂CTAB的作用下,随着反应时间的增加,生成的ZnS晶核生长成纳米颗粒,然后ZnS纳米颗粒将进一步发生团聚从而形成平均粒径超过500nm的ZnS纳米球,但制备的ZnS产物的晶体结构均为立方纤锌矿结构.随着ZnS粒径的增加,样品的紫外吸收峰从418nm逐渐蓝移到362nm,而PL发射峰位的峰强随着粒径的增大而增强.光催化结果显示,反应12h制备的ZnS纳米球的光催化性能最佳.