Determination of uranium fission interference factors for INAA

Instrumental neutron activation analysis (INAA) is a very suitable technique for the determination of several elements in different kinds of matrices. However, when the sample contains high uranium concentration this method presents interference problems of uranium fission products. The same radioisotopes used in INAA are formed in uranium fission. Among these radioisotopes are ¹⁴¹Ce, ¹⁴³Ce, ¹⁴⁰La, ⁹⁹Mo, ¹⁴⁷Nd, ¹⁵³Sm and ⁹⁵Zr. The purpose of this study was to evaluate uranium fission interference factors to be used in the INAA of environmental and geological samples containing high levels of U. The obtained interference factors agreed with literature reported values. The results point to the viability of using these experimentally determined interference factors for the correction of uranium fission products.     

Interference in neutron activation analysis of rocks by uranium fission

Interferences by uranium fission for⁹⁵Zr,⁹⁹Mo,¹⁰³Ru,¹⁴⁰La,¹⁴¹Ce and¹⁴⁷Nd have been studied using a single comparator method with two monitors. The effect of the neutron energy spectrum on the interference factor was examined by using the effective activation cross section. All the activities of¹⁴⁰La produced during neutron irradiation of uranium were included in the calculation of the factor for lanthanum. The calculated and experimental interference factors are in good agreement within 10% deviation. The results have been applied for the analysis of several rock samples containing uranium in a wide concentration range.     

Neutron activation analysis of pure uranium: Preconcentration of impurity elements

We have developed a radiochemical neutron activation analysis technique (RNAA) of pure uranium with using extraction chromatographic separation of ²³⁹Np from impurity elements in TBP-6M HNO₃ media. The estimation of influence of fission products of ²³⁵U on the results by radiochemical neutron activation analysis has been carried out. For it we have performed NAA with preconcentration of impurity elements. Experiments show that in this case the apparent concentration of Y, Zr, Mo, Cs, La, Ce, Pr, Nd exceeds the true concentration by 2500–3000 times. Therefore, determination of these elements is not possible by RNAA. This technique allowed to use the determination of 26 impurity elements with detection limit 10⁻⁵–10⁻⁹% by mass. This developed technique may be used for the determination of impurities in uranium and its compounds.     

Radiochemische Untersuchungen zur Verteilung von129J und3H in Bestrahltem Kernbrennstoff aus Leistungsreaktoren

The working techniques used for the investigation of¹²⁹I and³H sectional distribution in highly irradiated UO₂ pellets are described. The analytical samples are taken by a micro drilling technique. For the determination of¹²⁹I concentration in the UO₂ samples neutron activation analysis following iodine separation from uranium and bulk fission products is used.³H is measured by liquid scintillation counting after distillation. Reliability of the analytical results is discussed as well as possible interferences.     

The role of NAA in nuclear chemistry education

One of the missions of our Institute is the promotion of basic nuclear teaching for students as well as professional teaching for workers in nuclear industry and research. For nuclear chemistry education, we present here a one day teaching course on radioactive decay and nuclear reactions, and a two or three days course based on reactor irradiation of uranium oxide, instrumental and radiochemical analysis of fission products. In the first experiment, the neutron capture is presented as an example of nuclear reaction; the neutron activation of a silver coin with a Am-Be neutron source, followed by γ-ray spectrometry, is used to identify three radionuclides of silver and to calculate their half-lives. In the second experiment, our teaching reactor is used as a neutron source with a flux about 10¹⁰ n·cm⁻²·s⁻¹ at a low thermal power (10 kW). This low flux allows us to irradiate a small uranium sample which is usable for spectrometry after a short cooling time of about two hours. The first day is reserved for instrumental analysis of the fission products and a second day for the radiochemical separation of a fission radionuclides. With these experimental results, the students have to calculate the number of fissions in the irradiated sample. On optional third day for postgraduate students is devoted to the presentation of NAA and some applications as uranium determination by the fission product spectrometry.     

Intereferences from uranium fission in neutron-activation analysis in an Argonaut-type Low Flux Reactor

The interferences by uranium fission on the determination by neutron activation analysis of Zr, Mo, Ru, La, Ce, Nd and Sm are investigated for the Argonaut-type Low Flux Reactor at ECN, Petten, The Netherlands. In addition, the spectral interference of the determination of Sm by²³⁹Np is considered. The experimental values for fission yields are found to be in good agreement with calculated values based on recent cross-section compilations.     

High precision instrumental neutron activation analysis of uranium by multiple gamma-ray peak ratio determination

The method of multiple γ-ray peak ratio determination has been applied to the nondestructive neutron activation analysis of uranium in rocks and ores. The photopeaks of²³⁹Np gamma-rays produced by the activation of²³⁸U and those of the fission products of²³⁵U are a measure of the quantity of uranium in the irradiated sample, provided that the uranium is of natural isotopic composition. The ratios between the integrated areas of the different photopeaks are calculated and compared with those obtained for a uranium standard. The uranium concentration in the sample is calculated from the photopeaks whose ratios correspond, within the error limits to those of pure natural uranium. High accuracy better than ±2% has been obtained.     

Multielement analysis of uraniferous rocks by INAA: Special reference to interferences due to uranium and fission of uranium

The presence of uranium in a sample enhances the true values of La, Ce, Nd, Sm determined by INAA if appropriate corrections are not made for the interference. The enhancement of the true values comes about because the (n, γ) activation products of these elements, viz.¹⁴⁰La,¹⁴¹Ce,¹⁴⁷Nd,¹⁵³Sm, are also produced from the fission of²³⁵U (～0.72% natural isotopic abundance) even when La, Ce, Nd, Sm are totally absent in the given sample. In a 5 hour irradiation 1 μg of U is found to be equal to 0.28 μg of Ce and 0.23 μg of Nd while the equivalent La is found to be dependent upon the delay from end of irradiation to sample counting time. A numerical procedure is given to correct for these interferences. Spectral interferences from fission and (n, γ) β products of uranium in the determination of other trace elements by INAA is also investigated. Uranium is found to be determined best using the 278 keV gamma-ray of²³⁹Np.     

Radiochemical neutron activation analysis of Mo and W in geochemical and cosmochemical samples with an emphasis on the correction of fission products

Radiochemical neutron activation analysis (RNAA) was applied to geochemical and cosmochemical samples to determine trace amounts of Mo and W. To determine the Mo concentration by NAA accurately, the contribution of the fission products of U should be corrected. For that reason, we developed a simple and effective method, where a contribution of fissiogenic ⁹⁹Mo was estimated by monitoring the ratio of uranium fission-product ⁹⁹Mo to ¹³³I. Mo concentrations corrected for fission with the W concentrations were consistent with the literature values, showing that ¹³³I was found to be an effective monitor for fission correction. Detection limits are estimated to be 10 ppb for Mo and W and 30 ppb for U under the present experimental conditions.     

Production of99Mo and its application in nuclear medicine

Molybdenum-99 is produced in large quantities as the parent radioisotopes of^99mTc, which has been used recently in nuclear medicine. The neutron capture reaction on molybdenum and the nuclear fission of uranium are used for the large scale production of⁹⁹Mo. The products by these methods are used properly according to the objects of diagnosis. In this paper, the production of⁹⁹Mo is reviewed and the development of the production in JAERI is outlined.     

Determination of235U abundance in uranium by neutron activation on the basis of the molybdenum fission interference

The purpose of the present paper is to suggest a method for determining the²³⁵U abundance in uranium samples (compounds, metallic alloys or other uranium materials, where this element may be natural or not) through a particular application of neutron activation analysis, based on the fission interference by molybdenum. The method lies on an a priori calibration with natural uranium, thus it does not require²³⁵U certified standards.     

Chromatographic isolation of144Ce and144Pr from the wastes of irradiated uranium treatment

A two-step chromatographic technique was elaborated to isolate¹⁴⁴Ce,¹⁴⁴Pr from a solution of uranium fission products in 6M HNO₃. The oxidation to Ce(III) by bromate and selective adsorption of¹⁴⁴Ce(IV) on anion exchange column were used to concentrate and purify¹⁴⁴Ce. Some impurities of uranium,⁹⁵Zr,⁹⁵Nb,¹⁰⁶Ru remain in¹⁴⁴Ce solution after the first step of its isolation. The final purification is achieved by passing the 6M HNO₃ solution of¹⁴⁴Ce(IV) through the HDEHP-coated teflon column. The decontamination factors of¹⁴⁴Ce from main fission products are given. 7.2 mCi of (¹⁴⁴Ce+¹⁴⁴Pr) are recovered from each gram of irradiated uranium trioxide with the yield greater than 99%. An improvement of known generator was carried out to elute a purer¹⁴⁴Pr from maternal¹⁴⁴Ce(IV) adsorbed on the anion exchange column.     

Determination of the fast fission yield of141Pr using neutron activation analysis

A method is described for the determination of the fission yield of¹⁴¹Pr. This method was developed to determine the fast fission yield of¹⁴¹Pr in the Mark III loading (enriched uranium with about 2% zirconium) of the fast fission breeder reactor, EBR-1. The burnup of the fuel sample was determined using the previously reported fission yield of¹³⁷Cs. Praseodymium was separated from uranium, plutonium and other fission products by a combination of precipitation and ion exchange stages. Thereafter,⁵⁵Mn was added to serve as an internal flux monitor and praseodymium determined by neutron activation analysis. A precision of ±2% was obtained. Presented at the 15th Annual Meeting of the American Chemical Society, Miami Beach, Florida (USA), April 1967.     

Application of neutron activation analysis in a fission molybdenum separation study

The separation of⁹⁹Mo from low-enriched uranium (LEU, 19.5%²³⁵U) targets was evaluated using natural uranium (NU) and non-radioactive tracers. Neutron activation analysis was used to determine (1) the efficiency of molybdenum recovery and (2) the decontamination factor of numerous fission product elements from the molybdenum product. Using NU and non-radioactive elements simplified procedures and allowed tests to be completed in a fume hood instead of a shielded cell. During activation of the non-radioactive tracers, uranium fission occurs, which can interfere with subsequent gamma-ray analysis. A comparison was made of the interferences caused by these fission products from both NU and LEU.     

The determination of uranium in biological materials by neutron activation analysis using the fission product134I

A method for the determination of uranium based on²³⁵U thermal neutron fission, has been developed and employed on samples of ashed fish tissue and seaweed. The method involves a post-irradiation ion exchange separation of iodine isotopes. The 884 keV photopeak of¹³⁴I is used for measurement. Uranium detection limits in the samples concerned have been estimated to be 1·10⁻⁸g in terms of natural uranium. The precision achieved in analysing several series of 3–5 samples was 4–10 per cent. The accuracy of the method was tested by employing an independent neutron activation procedure based on²³⁹U measurement. The accuracy of both methods was checked by analysing NBS SRM 1571 ‘Orchard Leaves’.     

Imaging uranium distributions in fossil bones by fission track etching

In the course of our work within the framework of an interdisciplinary project dealing with the absolute dating of fossil bones from Austrian caves by means of the U-series method we became interested in possible U-concentration gradients in the bone samples. A successful attempt is reported to make the U-distribution in bones directly visible by irradiating the samples with thermal neutrons and detecting the emitted fission products of²³⁵U in a plastic foil using the track etch method. This turns out to be possible also for relatively small U-concentrations of the order of 1 ppm. The uranium seems to concentrate near the surfaces which is in qualitative agreement with earlier results from the literature obtained by means of neutron activation analysis.     

A critical review of bioassay techniques for actinides in light of ICRP recommendations for monitoring workers

A critical review is presented of bioassay techniques for actinides in light of ICRP recommendations for monitoring workers. It is obvious that very sensitive techniques are required to meet these recommendations. Alpha spectrometry, the most commonly employed technique for measuring actinides in bioassay samples, has limited sensitivity. There are, however, certain techniques which are sensitive enough to meet the recommendations of ICRP, such as, fission track analysis for²³⁹Pu and²³⁵U, neutron activation analysis for²³²Th, mass spectrometry for a number of radionuclides, and many techniques for uranium. ICP-mass spectrometry does not have enough sensitivity to be implemented as a method of choice for the bioassay of actinides at present, however, it is quite promising.     

Fission product yields in the fast-neutron fission of238U

The fission yields of 38 fission products in the fast-neutron induced fission of²³⁸U have been determined using a rapid, multiscaling gamma-ray spectroscopic method. To obtain absolute yields for fission products having half-lives ranging from 32 s to 40 d, a total of 56 multi-scaling gamma-ray spectra were collected using various irradiation and cooling periods. Gamma-rays and photopeak areas of interest were assigned to the fission products by their energies and half-lives. Fission product activities were evaluated from spectral data using growth and decay calculations and fission yields were determined by normalizing the¹⁴⁰Ba yield to the average value from reported data. The depleted uranium target, covered with a boron-cadmium thermal neutron shield, was used to keep interference from the fission of²³⁵U minimal. Results for the cumulative fission yields, including 17 mostly short-lived fission products measured for the first time, are compared with previous measurements and with the recommended yields in recent evaluations. The agreement, and some discrepancies, in the comparisons are discussed. No explicit even-odd pairing effects are observed in the fission yield data for fast-neutron induced fission of²³⁸U.     

A neutron activation analysis procedure for the determination of uranium,thorium and potassium in geologic samples

A neutron activation analysis procedure was developed for the determination of uranium, thorium and potassium in basic and ultrabasic rocks. The three elements are determined in the same 0.5-g sample following a 30-min irradiation in a thermal neutron flux of 2·10¹² n·cm^?2·sec^?1. Following radiochemical separation, the nuclides²³⁹U (T=23.5 m),²³³Th (T=22.2 m) and⁴²K (T=12.36 h) are measured by β-counting. A computer program is used to resolve the decay curves which are complex owing to contamination and the growth of daughter activities. The method was used to determine uranium, throium and potassium in the U. S. Geological Survey standard rocks DTS-1, PCC-1 and BCR-1. For 0.5-g samples the limits of detection for uranium, throium and potassium are 0.7, 1.0 and 10 ppb, respectively.     

Feasibility of using dendroanalysis of uranium as a biomarker for environmental contamination

A study was initiated to investigate the chronological deposition of uranium in certain species of trees growing on the site of a former uranium metal processing facility. The Feed Materials Production Center (FMPC) is located in Fernald, Ohio, and for roughly 40 years operated as a large scale uranium processing center. Core samples from several species of trees growing in different locations throughout the site were extracted using a 12.5 mm incremental wood boring drill bit. After extraction, each core sample was cut and packaged into individual sections representing 4 annual growth rings and submitted for instrumental neutron activation analysis (INAA). The reaction ²³⁵U(n,f)¹⁴⁰Ba→¹⁴⁰La+γ was evaluated using high resolution germanium gamma-spectroscopy to detect the 1.596 MeV photon emission from the fission product ¹⁴⁰La following a minimum of a 3 week decay. A total of 106 samples representing 7 individual trees of 3 unique species were irradiated. In addition to the tree-core samples, 18 quality control (QC) samples and 18 standard reference material (SRM) Fly Ash samples were irradiated with the core samples for determining neutron flux. The activity in any one sample in a batch was determined by comparison with the amount of natural uranium in the QC standards. No significantly measurable amount of uranium was detected in any of the tree core samples, although 3 tree core samples were in excess of the minimum detectable amount (30 ng).