电爆炸丝法制备纳米Al2O3粉末

 设计了电爆炸金属丝产生纳米金属氧化物粉末的实验装置，金属丝电爆炸腔采用圆筒结构，纳米粉末经过微孔滤膜过滤收集。成功制备了纳米Al₂O₃粉末，其平均粒度达到64.9 nm。对电爆炸金属丝产生纳米Al₂O₃粉末的物理条件进行了研究。结果表明实验条件对粉末粒度有重要影响：随气压的增加粉末平均粒度变大；随金属丝直径增大粉末平均粒度变大；粉末的平均粒度与电容器的初始储能也有一定的关系。     

Gd2O3:Eu3+纳米晶的燃烧合成及光致发光性质

采用柠檬酸作燃烧剂用燃烧合成法制备了Gd₂O₃:Eu³⁺纳米晶.用X射线衍射仪(XRD)、高分辨透射电子显微镜(HRTEM)和荧光分光光度计等对Gd₂O₃:Eu³⁺纳米晶的结构、形貌和发光性能进行了分析.结果表明：不同柠檬酸与稀土离子配比(C/M)制备的样品经800℃ 退火1 h后，均得到了纯立方相的Gd₂O₃:Eu³⁺纳米晶，晶粒尺寸约为30 nm，尺寸分布较窄，其中以C/M=1.0时制备的纳米晶结晶性最好，发光强度最大.Gd₂O₃:Eu³⁺纳米晶主发射峰位置均在612 nm处 (⁵D₀→⁷F₂跃迁)，激发光谱中电荷迁移态发生红移，观察到Gd³⁺向Eu³⁺的有效能量传递.对柠檬酸与稀土离子配比(C/M)对结晶度、发光性质等的影响也进行了分析和讨论.     

纳米离子导体在流体静压力下的复阻抗谱研究

 用惰性气体蒸发和真空原位加压方法制备了具有清洁界面的平均粒度16 nm的纳米固体CaF₂，并在0.1~2 400 MPa范围不同的静水压下用100 kHz~100 Hz内70种频率，精确测量了纳米CaF₂的复平面阻抗谱。分别给出纳米CaF₂离子电导率和相对介电常数随流体静压力的变化规律。最后的讨论指出：离子迁移通遭受压后的变化（大于、等于或小于最佳值）是影响离子电导率-压力曲线的主要因素；界面层空间电荷极化是造成纳米CaF₂相对介电常数较大的原因，由此界面效应可理解介电常数-压力曲线。     

超声强化合成MgFe2O4纳米颗粒及其机理研究

用超声水解方法制备MgO纳米颗粒,用化学沉淀法制备α-Fe₂O₃纳米颗粒,将MgO/α-Fe₂O₃混合体常温下超声活化2h,400℃固相合成制备出MgFe₂O₄纳米颗粒.通过X射线衍射和透射电子显微镜测试产品的化学成分、晶体结构和形貌尺寸,分析声化学反应机理及其影响因素.研究结果表明:所制备的MgFe₂O₄为尖晶石铁氧体,颗粒尺寸分布在20-30nm之间,粒度分布均匀;超声空化效应提高了化学反应活性、增加反应物的比表面积和反应物之间的接触面积,促进固相合成反应速度,降低反应温度,实现了一般条件下难以完成的化学反应.     

不同粒径纳米Y2Ba4CuBiOy 相掺杂对TSIG法单畴YBCO超导块材性能的影响

本文采用顶部籽晶熔渗方法(TSIG), 研究了不同粒径纳米Y₂Ba₄CuBiO_y粒子对单畴YBCO超导块材的生长形貌、微观结构及其磁悬浮力的影响.实验所用纳米Y₂Ba₄CuBiO_y粉体的平均粒度分别为283.0 nm, 170.4 nm以及82.5 nm, 每种粉体在YBCO超导块材中的含量均为2 wt%. 研究结果表明: 在掺杂量为2 wt%的情况下, Y₂Ba₄CuBiO_y粉体的粒度并不影响样品的宏观形貌, 均可制备出单畴YBCO块材; 并且成功地将纳米Y₂Ba₄CuBiO_y粒子引入单畴YBCO块材中, 且使其均匀分布, 但样品中的Y₂Ba₄CuBiO_y粒子均小于其初始粉体的粒度, 分别减小到270 nm, 150 nm和50 nm; 随着Y₂Ba₄CuBiO_y粉体初始粒度的减小, 样品的磁悬浮力逐渐增大, 分别为10 N, 17 N, 22 N. 该结果为进一步研究纳米磁通钉扎中心的引入方法及提高YBCO超导块材的性能有重大意义.     

银催化合成Tb(BO2)3纳米棒

采用固相反应银作催化剂成功合成出棒状结构的稀土硼酸盐Tb(BO₂)₃发光材料. 利用X射线衍射和区域电子衍射研究了产物的结构特性,在700 oC煅烧时,Tb(BO₂)₃纳米棒具有良好晶形. 透射电镜分析表明,Tb(BO₂)₃纳米棒直径为100～200 nm,厚度为30～50 nm,长约3 μm. 基于Ag纳米颗粒附在Tb(BO₂)₃纳米棒的顶端和中部的事实,探讨了Tb(BO₂)₃纳米棒的生长机理. 荧光光谱研究表明,在369 nm紫外光激发下,Tb(BO₂)₃能发出Tb³⁺的特征绿色荧光,发射主峰位于546 nm,归属于⁵D₄→⁷F₅跃迁. 同时,也探讨了煅烧温度对产物的结构、形貌以及发光性质的影响.     

纳米CaF2离子电导率和介电常数与流体静压力的关系

 采用惰性气体蒸发和真空原位加压方法，制备了具有清洁界面的平均粒度为14 nm的纳米固体CaF₂，并在0.1 MPa～2.2 GPa压力范围内52个不同的静水压下，分别详细测量出其离子电导率σ和相对介电常数随压力变化的规律。讨论指出：（1）离子迁移通道受压后的变化（大于、等于或小于最佳值），是影响离子电导率-压力曲线峰值的主要因素；（2）当压力从0.66 GPa再增加时，lg σ分三段线性下降，可归因于纳米晶体的三种自由体积；（3）界面层空间电荷极化是造成纳米CaF₂相对介电常数较大的原因，由此可理解介电常数的压力效应，了提高产品的氟离子电导率，用真空原位加压法制备纳米材料时，应当采用高于0.66 GPa的压力。     

Tm3+/Yb3+ ∶LaF3纳米体系中掺杂Yb3+ 离子对Tm3+ 离子荧光发射的影响

为研究Yb³⁺离子浓度变化对Tm³⁺离子在蓝色波段荧光强度的影响,以NaF和La(NO₃)₃为原料,采用水热法制备了Tm³⁺和Yb³⁺共掺的Tm³⁺/ Yb³⁺∶LaF₃纳米颗粒.用X射线衍射对LaF₃纳米颗粒进行表征的结果显示,纳米晶体结构呈六方相.透射电镜的观测结果显示,纳米颗粒样品大小均匀、分散性良好.在波长为800 nm的激光激发下,观测到了上转换蓝光发射,其中包括波长为474 nm和479 nm的较强的荧光辐射(相应的跃迁为1G4→3H6)和波长位于450 nm的强度较弱的荧光发射(相应的跃迁为1D2→3F4).通过观测不同Yb³⁺离子浓度条件下共掺Tm³⁺/Yb³⁺∶LaF₃样品的荧光光谱,研究了Yb³⁺离子掺杂浓度对于Tm³⁺离子的荧光发射的影响,并探讨了产生这种现象的原因.研究结果显示,对于1G4→3H6跃迁产生的荧光发射(474 nm),当Yb³⁺离子浓度增大时,反向能量传递速率的增加导致了荧光强度的增大.然而,当Yb³⁺离子浓度增大到一定程度时,Yb³⁺离子激发态能级寿命的减少将引发荧光强度的下降.相比较而言,Yb³⁺离子的浓度的变化对于1D2→3F4跃迁产生的位于450 nm处荧光强度的影响较弱.     

Ti+(CO2)2Ar和Ti+(CO2)n(n=3-7)络合物离子的红外光解离光谱 (cited: 1)

利用脉冲激光溅射-超声分子束载带方法制备了气相Ti⁺(CO₂)₂Ar和Ti⁺(CO₂)_n(n=3-7)络合物离子．采用红外光解离光谱研究了这些选定的质量离子的振动光谱． 对于每一种络合物离子, 在CO伸缩振动频率范围都观察到了振动峰,表明这些离子具有插入的OTi⁺CO(CO₂)_n-1结构． 对于n≦5的OTi⁺CO(CO₂)_n-1离子,其CO振动和CO₂的反对称伸缩振动频率都比自由的CO和CO₂的频率要高,表明CO和CO₂配体与中心金属离子之间主要是静电相互作用．实验结果还表明TiO⁺可以直接络合五个配体(1个CO和4个CO₂分子)．对于n=2络合物体系,除了插入的OTi⁺CO(CO₂)结构以外,还观察到了具有弯曲结构的OCO-Ti⁺-OCO异构体的存在     

Yb:CaF2-SrF2激光晶体光谱性能以及热学性能的研究

采用坩埚下降法生长了Yb: CaF₂-SrF₂晶体,测试了该晶体的吸收和荧光光谱 以及在不同温度下晶体的热扩散系数和热膨胀系数,并且计算了晶体的热膨胀系数以及在常温下的热导率. 采用对比的方法,对晶体的吸收光谱,荧光光谱,热学性能进行了分析.从吸收和荧光光谱结果表明: 在掺杂相对较高浓度的SrF₂的混晶中, Yb³⁺吸收截面和发射截面比较大. Yb: CaF₂-SrF₂ (19%)晶体在1040 nm附近的发射截面比较大,光谱也比较宽. 这说明在掺杂相同浓度Yb时,混晶中CaF₂, SrF₂的比例不同,晶体的光谱性质不同, 主要原因是在混晶中晶体的无序度不同,晶体对称性降低,形成低对称光学中心. 从热扩散系数计算的热导率结果看出晶体具有比较好的热导率.     

Conductivity enhancement in fluorite-structured Ba1−xLaxF2+x solid solutions

The ionic conductivity of single crystals of the fluorite-structured solid solutions Ba_1?xLa_xF_2+x(10^?3 <×<0.45) has been studied as a function of temperature and composition in the range 300–900 K. Three regions can be discerned in the concentration dependence of the ionic conductivity: a dilute concentration region (x<10^?3), where classic relations between solute content and ionic conductivity hold; an intermediate concentration region (10^?3<x?5×10^?2), where large changes occur in the conductivity activation enthalpy and the magnitude of the conductivity; and a concentrated solid solution region (x?5×10^?2) characterized by enhanced ionic motion. In the dilute region the migration enthalpy for interstitial fluoride ions is determined to be 0.714 eV, while a value of 0.39 eV is found for the (La_BaF_i)^X association enthalpy. The defect chemistry in the intermediate concentration region is shown to be controlled by a superlinear increase of the concentration of mobile defects, while in the concentrated solid solution region a composition-independent amount of ≈1 mole% of interstitial fluoride ions with enhanced mobility, carry the current.     

氧离子导体La1.9Y0.1Mo2O9细晶粒陶瓷的制备和电学性质研究

采用溶胶凝胶法合成的La_1.9Y_0.1Mo₂O₉纳米晶粉体, 结合微波烧结技术制备出不同晶粒度的La_1.9Y_0.1Mo₂O₉块体样品. 利用X射线衍射仪(XRD)、高分辨透射显微镜(HRTEM)、场扫描显微镜(SEM)对粉体及陶瓷块体的物相、 形貌进行了表征, 利用交流阻抗谱仪测试了样品不同温度下的电导率. 实验结果表明, 掺Y的La_1.9Y_0.1Mo₂O₉能将高温立方β 相稳定到室温; 块体样品致密均匀, 平均晶粒度范围在60 nm–4 μm之间; 致密度高的样品表现出高的电导率, 其中900 ℃烧结样品的电导率600 ℃时高达0.026 S/cm, 比固相反应法制备的La_1.9Y_0.1Mo₂O₉样品高出约1倍. 总结认为样品的致密性对电导率影响较大, 是通过影响晶界电导率来影响总电导率的, 样品的晶粒度(在60 nm–4 μm范围内)对电导率的影响还不能确定. 关键词： 氧离子导体 1.9Y_0.1Mo₂O₉')" href="#">La_1.9Y_0.1Mo₂O₉ 细晶粒陶瓷 微波烧结     

Li2SO4—Li2B2O4,Li2SO4—(NH4)2SO4赝二元系相图及离子导电性研究

本文用差热分析和X射线衍射方法对Li₂SO₄-Li₂B₂O₄和Li₂SO₄-[NH₄]₂SO₄两个赝二元系相图进行了研究。Li₂SO₄-Li₂B₂O₄是共晶体系,共晶温度为720℃ 关键词：     

非晶锂离子导体P2O5-0.7Li2O-0.4LiCl-0.1Al2O3的离子导电性与结构研究

本文研究了非晶锂离子导体P₂O₅-0.7Li₂O-0.4LiCl-0.1Al₂O₃的60目、120目、200目粉末、粉末压片和整片非晶在60至380℃的离子电导率和激活能。发现颗粒度减小能使离子电导率提高四倍以上,但不影响激活能,它归因于同一非晶相的界面效应。各样品在380℃等温热处理76h内的离子电导率和X射线衍射研究表明:颗粒度越小,晶化就越容易。整片非晶比粉末压片不仅电导率提高两个数量级,激 关键词：     

非晶态离子导体Li2B2O4晶化前期的离子导电性

本文研究了非晶态离子导体Li₂B₂O₄的离子电导率与温度的关系,特别着重于晶化前期的离子迁移特性。当温度低于T_K(≈310℃)时,离子电导率遵从Arrhenius关系。当高于晶化温度(≈411℃)时,以晶态中的离子迁移为主。在T_kc时,电导率偏离热激活机制呈反常增高。我们把这一过程称为晶化前期过程。可以用自由体积模型进行描述。晶化前期又可分为两部分:当温度低于、T_p(≈380℃)时,由于自由体积的重新分布,导致了电导率的增高;当T>T_p时,出现了少量微晶,但晶化量小于5%,由于非晶母体与微晶之间的界面效应使得离子导电性显著增强。可以通过室温淬火,把晶化前期非晶态的状态保持到室温,从而有可能制备出离子电导率高于纯非晶态的材料。 关键词：     

含碳Na-β(β")-Al2O3的导电性能

本文研究了含碳(1—10)wt％的Na-β(β″)-Al₂O₃,指出含碳6wt％以下仍是良好的快离子导体,而且由于混入了碳,离子电导率比纯的Na-β(β″)-Al₂O₃提高一到两个数量级。样品的体电阻,晶界电阻,双电层电容及其漏电阻等参量都随含碳量的不同而变化。文中详细地讨论了碳的影响。在-40℃到80℃温度范围测量了纯样品与含碳样品的电导温度特性,指出含碳的Na-β(β″)-Al₂O₃是做双电层电容器的良好材料。 关键词：     

Thermal conductivity of La0.67(CaxSr1−x)0.33MnO3 (x=0, 0.5, 1) and La0.6Y0.07Ca0.33MnO3 pellets between 10 and 300 K

Thermal conductivity (λ) of nanocrystalline La_0.67(Ca_xSr_1−x)_0.33MnO₃ (x=0, 0.5, 1) and La_0.6Y_0.07Ca_0.33MnO₃ pellets prepared by a novel ‘pyrophoric’ method have been studied between the temperature range 10 and 300 K. Our data show that the magnitude of thermal conductivity is strongly influenced by the ion substitutions at La-site. The analysis of the thermal conductivity data indicates that the thermal transport is governed largely by phonons scattering in these systems and the electronic contribution is as small as 0.2-1% of total thermal conductivity (λ_total). At low temperatures (<90 K) 2D like lattice defects contribute to the phonon scattering dominantly and its strength increases with increasing Sr content and also with partial substitution of La by Y. Depending upon the composition of the samples, the magnon thermal conductivity contributes 2-15% of λ_total close to T_C. In the paramagnetic regime the unusual increase in λ_total keeps signature of large dynamic lattice distortion.     

Ionic conductivity in tysonite-type solid solutions La1−xBaxF3−x

The ionic conductivity of single crystals of tysonite-type solid solutions La_1?xBa_xF_3?x(0?x?0.095) has been studied parallel and perpendicular to the crystallographic c axis in the temperature range 293–1300 K. Three regions can be discerned in the compositional dependence of the ionic conductivity: (i) the “pure” crystal, in which at room temperature no exchange occurs between different types of anion sites in the tysonite structure; (ii) an intermediate region(0 < x < 7 × 10^-2) which reveals changes in both the conductivity activation enthalpy and the magnitude of the conductivity; (iii) a concentrated solid-solution region (x > 7 × 10^-2), where fluoride ions interchange easily among the different anion sublattices. Diffusion coefficients calculated from ionic conductivity results, are in good agreement with those calculated from ¹⁹F NMR measurements. Using the present data, along with ¹⁹F NMR data, dielectric relaxation data and structural considerations, mechanisms governing the ionic conductivity are proposed.     

Ionic conductivity in the single crystals of non-stoichiometric fluorite phases M1−xRxF2+x (M=Ca,Sr, Ba; R=Y,La-Lu)

The ionic conductivity has been measured of single crystals of rare earth fluoride solid solutions in Ca, Sr and Ba fluorides described by the formula M_1?xR_xF_2+x (M=Ca, Sr, Ba; R=Y, La-Lu). The measurements have been done using dc and ac within the temperature range 300–850 K. With the increase of RF₃ concentration up to x=0.05–0.15 (in different systems) conductivity steeply increases. With the further concentration growth the conductivity increases only slightly, reaching saturation value for the solid solution Ba_1?xR_xF_2+x. The dependence of solid solution conductivity on the chemical composition has been studied for isoconcentrates M_0.9R_0.1F_2.1. It has been established that in CaF_2- based series the crystals with R=Gd, Tb possess maximum conductivity and minimum activation energy. For SrF₂ and BaF₂-based series the highest conductivity was observed for crystals containing LaF₃. It has been established that for all the crystals, independent of the chemical composition and defect concentration, the conductivity logarithm at definite temperature linearly depends on the activation energy. Within the investigated class of substances the optimum composition for solid electrolytes is Sr_0.69La_0.31F_2.31.     

Studies of defect clustering in CaF2: Y3+ by ionic conductivity and thermal depolarization

Measurements of the ionic conductivity σ of yttrium-doped calcium fluoride reveal a complex and highly unusual dependence of logσT on T^?1, where T denotes the temperature. This conductivity curve has been interpreted in terms of a model that assumes frozen-in defects on the cation sub-lattice together with charge-compensating interstitial fluoride ions and anion vacancies. At low temperatures the conductivity is dominated by mobile interstitial fluoride ions (F_i^?) in equilibrium with trapping centres that may include substitutional yttrium ions (Y_s³⁺), Y_s³⁺?F_i^? complexes (monomers) and larger clusters. At intermediate temperatures the charge-carrying F_i^? are considered to arise by ionization from dimers (the 2:2:2 complexes) and at higher temperatures still from larger clusters which are probably tetramers, although the possibility that the mobile F_i^? in these two temperature regions are those that had formerly been trapped by dimers and tetramers cannot be excluded. The thermal depolarization spectrum of CaF₂: Y³⁺ is very complicated and reveals six different relaxations. One of these is associated with the type I (nn) and type II (nnn) Y_s³⁺?F_i^? complexes and a second with 2:2:2 clusters. The remaining four relaxations were not identified but almost certainly provide evidence for the existence of polarizable defect clusters in CaF₂: Y³⁺.