Realizing Complete Solid‐Solution Reaction in High Sodium Content P2‐Type Cathode for High‐Performance Sodium‐Ion Batteries

P2‐type layered oxides suffer from an ordered Na⁺/vacancy arrangement and P2→O2/OP4 phase transitions, leading them to exhibit multiple voltage plateaus upon Na⁺ extraction/insertion. The deficient sodium in the P2‐type cathode easily induces the bad structural stability at deep desodiation states and limited reversible capacity during Na⁺ de/insertion. These drawbacks cause poor rate capability and fast capacity decay in most P2‐type layered oxides. To address these challenges, a novel high sodium content (0.85) and plateau‐free P2‐type cathode‐Na_0.85Li_0.12Ni_0.22Mn_0.66O₂ (P2‐NLNMO) was developed. The complete solid‐solution reaction over a wide voltage range ensures both fast Na⁺ mobility (10^?11 to 10^?10 cm² s^?1) and small volume variation (1.7 %). The high sodium content P2‐NLNMO exhibits a higher reversible capacity of 123.4 mA h g^?1, superior rate capability of 79.3 mA h g^?1 at 20 C, and 85.4 % capacity retention after 500 cycles at 5 C. The sufficient Na and complete solid‐solution reaction are critical to realizing high‐performance P2‐type cathodes for sodium‐ion batteries.     

Lithium‐Rich Layered Oxide Li1.18Ni0.15Co0.15Mn0.52O2 as the Cathode Material for Hybrid Sodium‐Ion Batteries

Li‐rich layered oxide Li_1.18Ni_0.15Co_0.15Mn_0.52O₂ (LNCM) is, for the first time, examined as the positive electrode for hybrid sodium‐ion battery and its Na⁺ storage properties are comprehensively studied in terms of galvanostatic charge–discharge curves, cyclic voltammetry and rate capability. LNCM in the proposed sodium‐ion battery demonstrates good rate capability whose discharge capacity reaches about 90 mA h g^?1 at 10 C rate and excellent cycle stability with specific capacity of about 105 mA h g^?1 for 200 cycles at 5 C rate. Moreover, ex situ ICP‐OES suggests interesting mixed‐ions migration processes: In the initial two cycles, only Li⁺ can intercalate into the LNCM cathode, whereas both Li⁺ and Na⁺ work together as the electrochemical cycles increase. Also the structural evolution of LNCM is examined in terms of ex situ XRD pattern at the end of various charge–discharge scans. The strong insight obtained from this study could be beneficial to the design of new layered cathode materials for future rechargeable sodium‐ion batteries.     

Towards Highly Stable Storage of Sodium Ions: A Porous Na3V2(PO4)3/C Cathode Material for Sodium‐Ion Batteries

A porous Na₃V₂(PO₄)₃ cathode material coated uniformly with a layer of approximately 6 nm carbon has been synthesized by the sol–gel method combined with a freeze‐drying process. The special porous morphology and structure significantly increases the specific surface area of the material, which greatly enlarges the contact area between the electrode and electrolyte, and consequently supplies more active sites for sodium ions. When employed as a cathode material of sodium‐ion batteries, this porous Na₃V₂(PO₄)₃/C exhibits excellent rate performance and cycling stability; for instance, it shows quite a flat potential plateau at 3.4 V in the potential window of 2.7–4.0 V versus Na⁺/Na and delivers an initial capacity as high as 118.9 and 98.0 mA h g^?1 at current rates of 0.05 and 0.5 C, respectively, and after 50 cycles, a good capacity retention of 92.7 and 93.6 % are maintained. Moreover, even when the discharge current density is increased to 5 C (590 mA g^?1), an initial capacity of 97.6 mA h g^?1 can still be achieved, and an exciting capacity retention of 88.6 % is obtained after 100 cycles. The good cycle performance, excellent rate capability, and moreover, the low cost of Na₃V₂(PO₄)₃/C suggest that this material is a promising cathode for large‐scale sodium‐ion rechargeable batteries.     

长循环高电压钠离子电池正极材料P2-Na2/3Mn1/3Bi1/3Ni1/3O2的合成及性能

镍基层状氧化物NaNiO₂钠离子电池材料具有高电压和高容量的特性,且制备方法较为简单,但姜-泰勒(Jahn-Teller)效应使其在高倍率循环下容量较低以及在高电压(4.5 V)下无法稳定循环。通过调节溶胶-凝胶工艺的条件,设计、合成了Na_2/3Mn_1/3Bi_1/3Ni_1/3O₂片层状金属氧化物,并将其作为正极活性材料,在空气环境中组装成钠离子电池,进行电化学测试,考察Bi、Mn掺入量对电池电化学影响。研究结果表明:当金属Mn和Bi共掺时,在1.2~4.5 V宽电压范围内,电池在循环50周后容量为90.39 mAh·g^-1。在2.0~4.0 V电压范围内1.0C (115 mA·g^-1)倍率下恒流充放电50周后的容量保持率为96.96%,循环850周后的保持率为80.15%,具有良好的循环稳定性和安全性。     

长循环高电压钠离子电池正极材料P2-Na2/3Mn1/3Bi1/3Ni1/3O2的合成及性能

镍基层状氧化物NaNiO₂钠离子电池材料具有高电压和高容量的特性,且制备方法较为简单,但姜-泰勒(Jahn-Teller)效应使其在高倍率循环下容量较低以及在高电压(4.5 V)下无法稳定循环。通过调节溶胶-凝胶工艺的条件,设计、合成了Na_2/3Mn_1/3Bi_1/3Ni_1/3O₂片层状金属氧化物,并将其作为正极活性材料,在空气环境中组装成钠离子电池,进行电化学测试,考察Bi、Mn掺入量对电池电化学影响。研究结果表明：当金属Mn和Bi共掺时,在1.2~4.5 V宽电压范围内,电池在循环50周后容量为90.39 mAh·g^-1。在2.0~4.0 V电压范围内1.0C (115 mA·g^-1)倍率下恒流充放电50周后的容量保持率为96.96%,循环850周后的保持率为80.15%,具有良好的循环稳定性和安全性。     

长循环高电压钠离子电池正极材料P2-Na2/3Mn1/3Bi1/3Ni1/3O2的合成及性能

镍基层状氧化物NaNiO₂钠离子电池材料具有高电压和高容量的特性,且制备方法较为简单,但姜-泰勒(Jahn-Teller)效应使其在高倍率循环下容量较低以及在高电压(4.5 V)下无法稳定循环。通过调节溶胶-凝胶工艺的条件,设计、合成了Na_2/3Mn_1/3Bi_1/3Ni_1/3O₂片层状金属氧化物,并将其作为正极活性材料,在空气环境中组装成钠离子电池,进行电化学测试,考察Bi、Mn掺入量对电池电化学影响。研究结果表明：当金属Mn和Bi共掺时,在1.2~4.5 V宽电压范围内,电池在循环50周后容量为90.39 mAh·g^-1。在2.0~4.0 V电压范围内1.0C (115 mA·g^-1)倍率下恒流充放电50周后的容量保持率为96.96%,循环850周后的保持率为80.15%,具有良好的循环稳定性和安全性。     

P2‐NaCo0.5Mn0.5O2 as a Positive Electrode Material for Sodium‐Ion Batteries

As a promising positive electrode material for sodium‐ion batteries (SIBs), layered sodium oxides have attracted considerable attention in recent years. In this work, stoichiometric P2‐phase NaCo_0.5Mn_0.5O₂ was prepared through the conventional solid‐state reaction, and its structural and physical properties were studied in terms of XRD, XPS, and magnetic susceptibility. Furthermore, the P2‐NaCo_0.5Mn_0.5O₂ electrode delivered a discharge capacity of 124.3 mA h g^?1 and almost 100 % initial coulombic efficiency over the potential window of 1.5–4.15 V. It also showed good cycle stability, with a reversible capacity and capacity retention reaching approximately 85 mA h g^?1 and 99 %, respectively, at the 5 C rate after 100 cycles. Additionally, cyclic voltammetry and ex situ XRD were employed to explain the electrochemical behavior at the different electrochemical stages. Owing to the applicable performances, P2‐NaCo_0.5Mn_0.5O₂ can be considered as a potential positive electrode material for SIBs.     

Coating of Al2O3 on layered Li(Mn1/3Ni1/3Co1/3)O2 using CO2 as green precipitant and their improved electrochemical performance for lithium ion batteries

Li(Mn_1/3Ni_1/3Co_1/3)O₂ cathode materials were fabricated by a hydroxide precursor method. Al₂O₃ was coated on the surface of the Li(Mn_1/3Ni_1/3Co_1/3)O₂ through a simple and effective one-step electrostatic self-assembly method. In the coating process, a NHCO₃-H₂CO₃ buffer was formed spontaneously when CO₂ was introduced into the NaAlO₂ solution. Compared with bare Li(Mn_1/3M_1/3Co_1/3)O₂, the surface-modified samples exhibited better cycling performance, rate capability and rate capability retention. The Al₂O₃-coated Li(Mn_1/3Ni_1/3Co_1/3)O₂ electrodes delivered a discharge capacity of about 115 mAh·g^?1 at 2 A·g^?1, but only 84 mAh·g^?1 for the bare one. The capacity retention of the Al₂O₃-coated Li(Mn_1/3Ni_1/3Co_1/3)O₂ was 90.7% after 50 cycles, about 30% higher than that of the pristine one.     

A Facile Synthesis of High‐Surface‐Area Sulfur–Carbon Composites for Li/S Batteries

Small‐grained elemental sulfur is precipitated from sodium thiosulfate (Na₂S₂O₃) in a carbon‐containing oxalic acid (HOOC?COOH) solution through a novel spray precipitation method. Surface area analysis, elemental mapping, and transmission electron micrographs revealed that the spray‐precipitated sulfur particles feature 11 times higher surface area compared to conventional precipitated sulfur, with homogeneous distribution in the carbon. Moreover, the scanning electron micrographs show that these high‐surface‐area sulfur particles are firmly adhered to and covered by carbon. This precipitated S–C composite exhibits high discharge capacity with about 75 % capacity retention. The initial discharge capacity was further improved to 1444 mA h g^?1 by inserting a free‐standing single‐walled carbon nanotube layer in between the cathode and the separator. Moreover, with the help of the fixed capacity charging technique, 91.6 % capacity retention was achieved.     

Electrochemical Properties and Sodium‐Storage Mechanism of Ag2Mo2O7 as the Anode Material for Sodium‐Ion Batteries

Silver molybdate, Ag₂Mo₂O₇, has been prepared by a conventional solid‐state reaction. Its electrochemical properties as an anode material for sodium‐ion batteries (SIBs) have been comprehensively examined by means of galvanostatic charge–discharge cycling, cyclic voltammetry, and rate performance measurements. At operating voltages between 3.0 and 0.01 V, the electrode delivered a reversible capacity of nearly 190 mA h g^?1 at a current density of 20 mA g^?1 after 70 cycles. Ag₂Mo₂O₇ also demonstrated a good rate capability and long‐term cycle stability, the capacity reaching almost 100 mA h g^?1 at a current density of 500 mA g^?1, with a capacity retention of 55 % over 1000 cycles. Moreover, the sodium storage process of Ag₂Mo₂O₇ has been investigated by means of ex situ XRD, Raman spectroscopy, and HRTEM. Interestingly, the anode decomposes into Ag metal and Na₂MoO₄ during the initial discharge process, and then Na⁺ ions are considered to be inserted into/extracted from the Na₂MoO₄ lattice in the subsequent cycles governed by an intercalation/deintercalation mechanism. Ex situ HRTEM images revealed that Ag metal not only remains unchanged during the sodiation/desodiation processes, but is well dispersed throughout the amorphous matrix, thereby greatly improving the electronic conductivity of the working electrode. The “in situ” decomposition behavior of Ag₂Mo₂O₇ is distinct from that of chemically synthesized, metal‐nanoparticle‐coated electrode materials, and provides strong supplementary insight into the mechanism of such new anode materials for SIBs and may set a precedent for the design of further materials.     

P2‐Na0.67AlxMn1−xO2: Cost‐Effective,Stable and High‐Rate Sodium Electrodes by Suppressing Phase Transitions and Enhancing Sodium Cation Mobility

Sodium layered P2‐stacking Na_0.67MnO₂ materials have shown great promise for sodium‐ion batteries. However, the undesired Jahn–Teller effect of the Mn⁴⁺/Mn³⁺ redox couple and multiple biphasic structural transitions during charge/discharge of the materials lead to anisotropic structure expansion and rapid capacity decay. Herein, by introducing abundant Al into the transition‐metal layers to decrease the number of Mn³⁺, we obtain the low cost pure P2‐type Na_0.67Al_xMn_1?xO₂ (x=0.05, 0.1 and 0.2) materials with high structural stability and promising performance. The Al‐doping effect on the long/short range structural evolutions and electrochemical performances is further investigated by combining in situ synchrotron XRD and solid‐state NMR techniques. Our results reveal that Al‐doping alleviates the phase transformations thus giving rise to better cycling life, and leads to a larger spacing of Na⁺ layer thus producing a remarkable rate capability of 96 mAh g^‐1 at 1200 mA g^‐1.     

P2‐Na0.67AlxMn1−xO2: Cost‐Effective,Stable and High‐Rate Sodium Electrodes by Suppressing Phase Transitions and Enhancing Sodium Cation Mobility

Sodium layered P2‐stacking Na_0.67MnO₂ materials have shown great promise for sodium‐ion batteries. However, the undesired Jahn–Teller effect of the Mn⁴⁺/Mn³⁺ redox couple and multiple biphasic structural transitions during charge/discharge of the materials lead to anisotropic structure expansion and rapid capacity decay. Herein, by introducing abundant Al into the transition‐metal layers to decrease the number of Mn³⁺, we obtain the low cost pure P2‐type Na_0.67Al_xMn_1?xO₂ (x=0.05, 0.1 and 0.2) materials with high structural stability and promising performance. The Al‐doping effect on the long/short range structural evolutions and electrochemical performances is further investigated by combining in situ synchrotron XRD and solid‐state NMR techniques. Our results reveal that Al‐doping alleviates the phase transformations thus giving rise to better cycling life, and leads to a larger spacing of Na⁺ layer thus producing a remarkable rate capability of 96 mAh g^‐1 at 1200 mA g^‐1.     

High Crystalline Prussian White Nanocubes as a Promising Cathode for Sodium‐ion Batteries

Prussian blue and its analogues (PBAs) have been recognized as one of the most promising cathode materials for room‐temperature sodium‐ion batteries (SIBs). Herein, we report high crystalline and Na‐rich Prussian white Na₂CoFe(CN)₆ nanocubes synthesized by an optimized and facile co‐precipitation method. The influence of crystallinity and sodium content on the electrochemical properties was systematically investigated. The optimized Na₂CoFe(CN)₆ nanocubes exhibited an initial capacity of 151 mA h g^?1, which is close to its theoretical capacity (170 mA h g^?1). Meanwhile, the Na₂CoFe(CN)₆ cathode demonstrated an outstanding long‐term cycle performance, retaining 78 % of its initial capacity after 500 cycles. Furthermore, the Na₂CoFe(CN)₆ Prussian white nanocubes also achieved a superior rate capability (115 mA h g^?1 at 400 mA g^?1, 92 mA h g^?1 at 800 mA g^?1). The enhanced performances could be attributed to the robust crystal structure and rapid transport of Na ions through large channels in the open‐framework. Most noteworthy, the as‐prepared Na₂CoFe(CN)₆ nanocubes are not only low‐cost in raw materials but also contain a rich sodium content (1.87 Na ions per lattice unit cell), which will be favorable for full cell fabrication and large‐scale electric storage applications.     

A Superior Na3V2(PO4)3‐Based Nanocomposite Enhanced by Both N‐Doped Coating Carbon and Graphene as the Cathode for Sodium‐Ion Batteries

A superior Na₃V₂(PO₄)₃‐based nanocomposite (NVP/C/rGO) has been successfully developed by a facile carbothermal reduction method using one most‐common chelator, disodium ethylenediamintetraacetate [Na₂(C₁₀H₁₆N₂O₈)], as both sodium and nitrogen‐doped carbon sources for the first time. 2D‐reduced graphene oxide (rGO) nanosheets are also employed as highly conductive additives to facilitate the electrical conductivity and limit the growth of NVP nanoparticles. When used as the cathode material for sodium‐ion batteries, the NVP/C/rGO nanocomposite exhibits the highest discharge capacity, the best high‐rate capabilities and prolonged cycling life compared to the pristine NVP and single‐carbon‐modified NVP/C. Specifically, the 0.1 C discharge capacity delivered by the NVP/C/rGO is 116.8 mAh g^?1, which is obviously higher than 106 and 112.3 mAh g^?1 for the NVP/C and pristine NVP respectively; it can still deliver a specific capacity of about 80 mAh g^?1 even at a high rate up to 30 C; and its capacity decay is as low as 0.0355 % per cycle when cycled at 0.2 C. Furthermore, the electrochemical impedance spectroscopy was also implemented to compare the electrode kinetics of all three NVP‐based cathodes including the apparent Na diffusion coefficients and charge‐transfer resistances.     

One‐Step Pyro‐Synthesis of a Nanostructured Mn3O4/C Electrode with Long Cycle Stability for Rechargeable Lithium‐Ion Batteries

A nanostructured Mn₃O₄/C electrode was prepared by a one‐step polyol‐assisted pyro‐synthesis without any post‐heat treatments. The as‐prepared Mn₃O₄/C revealed nanostructured morphology comprised of secondary aggregates formed from carbon‐coated primary particles of average diameters ranging between 20 and 40 nm, as evidenced from the electron microscopy studies. The N₂ adsorption studies reveal a hierarchical porous feature in the nanostructured electrode. The nanostructured morphology appears to be related to the present rapid combustion strategy. The nanostructured porous Mn₃O₄/C electrode demonstrated impressive electrode properties with reversible capacities of 666 mAh g^?1 at a current density of 33 mA g^?1, good capacity retentions (1141 mAh g^?1 with 100 % Coulombic efficiencies at the 100^th cycle), and rate capabilities (307 and 202 mAh g^?1 at 528 and 1056 mA g^?1, respectively) when tested as an anode for lithium‐ion battery applications.     

A High‐Voltage and Ultralong‐Life Sodium Full Cell for Stationary Energy Storage

Recently, there has been great interest in developing advanced sodium‐ion batteries for large‐scale application. Most efforts have concentrated on the search for high‐performance electrode materials only in sodium half‐cells. Research on sodium full cells for practical application has encountered many problems, such as insufficient cycles with rapid capacity decay, low safety, and low operating voltage. Herein, we present a layered P2‐Na_0.66Ni_0.17Co_0.17Ti_0.66O₂, as both an anode (ca. 0.69 V versus Na⁺/Na) and as a high‐voltage cathode (ca. 3.74 V versus Na⁺/Na). The full cell based on this bipolar electrode exhibits well‐defined voltage plateaus near 3.10 V, which is the highest average voltage in the symmetric cells. It also shows the longest cycle life (75.9 % capacity retention after 1000 cycles) in all sodium full cells, a usable capacity of 92 mAh g^?1, and superior rate capability (65 mAh g^?1 at a high rate of 2C).     

Environmentally compatible dimethyl sulfoxide: an alternative to N-methylpyrrolidone for electrochemical performance of recycled LiMn1/3Ni1/3Co1/3O2 in lithium-ion battery

The effect of recycling and doping LiMn_1/3Ni_1/3Co_1/3O₂ of lithium-ion battery with dimethyl sulfoxide (DMSO) instead of N-methylpyrrolidone (NMP) on the electrochemical performance of the battery has been investigated for the first time. Observation shows that preparing the cathode active materials with dimethyl sulfoxide will increase the conductivity of the battery. The results show that the as-recovered LiMn_1/3Ni_1/3Co_1/3O₂ modified with LiOH · H₂O calcined at 450°C delivers discharge capacities of about 247 mA h g^?1 in the first cycle with discharge efficiency of 83.1% in sample doped with dimethyl sulfoxide, and 189 mA h g^?1 with discharge efficiency of 82.7% in N-methylpyrrolidone at the rate of 0.2 C. The asrecovered samples calcined at 800 and 850°C deliver 149 and 217 mA h g^?1 in the fourth cycles respectively in dimethyl sulfoxide. The capacity loss observed in dimethyl sulfoxide faded with increase in cycle numbers. In general, for the samples doped with dimethyl sulfoxide, better performances were evident with high discharge capacities in powders calcined at a lower temperature than higher temperature in accordance with particle sizes shown by the SEM images. On the basis of better cyclic performance of lithium metal cathode and environmental safety, it is evident that relatively cheap dimethyl sulfoxide could replace N-methylpyrrolidone in battery formulations. The X-ray diffraction patterns revealed that LiMn_1/3Ni_1/3Co_1/3O₂ was successfully recycled by dimethyl sulfoxide.     

Regulating Cation Interactions for Zero-Strain and High-Voltage P2-type Na2/3Li1/6Co1/6Mn2/3O2 Layered Oxide Cathodes of Sodium-Ion Batteries

Deep sodium extraction/insertion of sodium cathodes usually causes undesired Jahn–Teller distortion and phase transition, both of which will reduce structural stability and lead to poor long-cycle reliability. Here we report a zero-strain P2- Na_2/3Li_1/6Co_1/6Mn_2/3O₂ cathode, in which the lithium/cobalt substitution contributes to reinforcing the host structure by reducing the Mn³⁺/Mn⁴⁺ redox, mitigating the Jahn–Teller distortion, and minimizing the lattice change. 94.5 % of Na⁺ in the unit structure can be reversibly cycled with a charge cut-off voltage of 4.5 V (vs. Na⁺/Na). Impressively, a solid-solution reaction without phase transitions is realized upon deep sodium (de)intercalation, which poses a minimal volume deviation of 0.53 %. It attains a high discharge capacity of 178 mAh g⁻¹, a high energy density of 534 Wh kg⁻¹, and excellent capacity retention of 95.8 % at 1 C after 250 cycles.     

Effects of complexants on [Ni1/3Co1/3Mn1/3]CO3 morphology and electrochemical performance of LiNi1/3Co1/3Mn1/3O2

LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials for the application of lithium ion batteries were synthesized by carbonate co-precipitation routine using different ammonium salt as a complexant. The structures and morphologies of the precursor [Ni_1/3Co_1/3Mn_1/3]CO₃ and LiNi_1/3Co_1/3Mn_1/3O₂ were investigated through X-ray diffraction, scanning electron microscope, and transmission electron microscopy. The electrochemical properties of LiNi_1/3Co_1/3Mn_1/3O₂ were examined using charge/discharge cycling and cyclic voltammogram tests. The results revealed that the microscopic structures, particle size distribution, and the morphology properties of the precursor and electrochemical performance of LiNi_1/3Co_1/3Mn_1/3O₂ were primarily dependent on the complexant. Among all as-prepared LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials, the sample prepared from Na₂CO₃–NH₄HCO₃ routine using NH₄HCO₃ as the complexant showed the smallest irreversible capacity of 19.5 mAh g⁻¹ and highest discharge capacity of 178.4 mAh g⁻¹ at the first cycle as well as stable cycling performance (98.7% of the initial capacity was retained after 50 cycles) at 0.1 C (20 mA g⁻¹) in the voltage range of 2.5–4.4 V vs. Li⁺/Li. Moreover, it delivered high discharge capacity of over 135 mAh g⁻¹ at 5 C (1,000 mA g⁻¹).     

Cu3V2O8 Nanoparticles as Intercalation‐Type Anode Material for Lithium‐Ion Batteries

Cu₃V₂O₈ nanoparticles with particle sizes of 40–50 nm have been prepared by the co‐precipitation method. The Cu₃V₂O₈ electrode delivers a discharge capacity of 462 mA h g^?1 for the first 10 cycles and then the specific capacity, surprisingly, increases to 773 mA h g^?1 after 50 cycles, possibly as a result of extra lithium interfacial storage through the reversible formation/decomposition of a solid electrolyte interface (SEI) film. In addition, the electrode shows good rate capability with discharge capacities of 218 mA h g^?1 under current densities of 1000 mA g^?1. Moreover, the lithium storage mechanism for Cu₃V₂O₈ nanoparticles is explained on the basis of ex situ X‐ray diffraction data and high‐resolution transmission electron microscopy analyses at different charge/discharge depths. It was evidenced that Cu₃V₂O₈ decomposes into copper metal and Li₃VO₄ on being initially discharged to 0.01 V, and the Li₃VO₄ is then likely to act as the host for lithium ions in subsequent cycles by means of the intercalation mechanism. Such an “in situ” compositing phenomenon during the electrochemical processes is novel and provides a very useful insight into the design of new anode materials for application in lithium‐ion batteries.