Preparation and characterization of poly(acrylic acid)-based nanoparticles

The present investigation describes the synthesis and characterization of nanoparticles based on poly(acrylic acid) (PAA) intramolecularly cross-linked with diamine, 2,2′-(ethylenedioxy)bis(ethylamine), using water-soluble carbodiimide. The aqueous colloid dispersions of nanoparticles were clear or mildly opalescent depending on the ratio of cross-linking, pH of the solution, and the molecular weight of PAA, finding consistent with values of transmittance between 3% and 99%. The structure was determined by nuclear magnetic resonance spectroscopy, and the particle size was identified by dynamic light scattering (DLS) and transmission electron microscopy (TEM) measurements. It was found that particle size depends on the pH, and at a given pH, it was caused by the ratio of cross-linking and the molecular weight of PAA. Particle size measured by TEM varied in the range of 20 and 80 nm. In the swollen state, the average size of the particles measured by DLS was in the range of 35–160 nm.     

Cellulose II nanoelements prepared from fully mercerized, partially mercerized and regenerated celluloses by 4-acetamido-TEMPO/NaClO/NaClO2 oxidation

A softwood bleached kraft pulp (SBKP) and cotton lint cellulose were fully or partially mercerized, and these along with celluloses and commercially available regenerated cellulose fiber and beads were oxidized by 4-acetamido-TEMPO/NaClO/NaClO₂ at 60 °C and pH 4.8. Weight recovery ratios and carboxylate contents of the oxidized celluloses were 65–80% and 1.8–2.2 mmol g⁻¹, respectively. Transparent and viscous dispersions were obtained by mechanical disintegration of the TEMPO-oxidized celluloses in water. These aqueous dispersions showed birefringence between cross-polarizers, indicating that mostly individualized cellulose nanoelements dispersed in water were obtained by these procedures. Transmission electron microscopy observation showed that the cellulose nanoelements prepared from mercerized SBKP, repeatedly mercerized SBKP, mercerized cotton lint cellulose, regenerated cellulose beads and 18% NaOH-treated SBKP, i.e. partially mercerized SBKP, had similar morphologies and sizes, 4–12 nm in width and 100–200 nm in length. The 18% NaOH-treated SBKP was converted to cellulose nanoelements consisting of both celluloses I and II.     

Synthesis, polymerization, and dispersion copolymerization of poly(ethylene oxide) macromonomers carrying methacryloyloxyalkyl end groups

 Poly(ethylene oxide) macromonomers carrying methoxy group on the one (α-) end and methacryloyloxyhexyl or methacryloyloxydecyl group on the other (ω-) end were prepared, homopolymerized in water, and dispersion-copolymer-ized with styrene or methyl methacrylate in a methanol–water mixture. They were found to polymerize more rapidly and to produce stable polystyrene dispersions more effectively, as compared to the corresponding macromonomers carrying either α-methoxy and or α-dodecyloxy and ω-methacryloyloxy end groups. Thus, the amphiphilic constitution of the macromonomers such that favors the polymerizing methacrylate end groups to locally concentrate into the micelle core or to the particle surface while the poly(ethylene oxide) chains extending to the medium appears to be most important in enhancing their polymerizability and effectiveness as reactive steric stabilizers. On the other hand, stable poly(methyl methacry-late) particles with a number of craters or pleats on the surface were produced with a PEO macromono-mer with α-methoxy and ω-methacryl-oyloxy end groups. Received: 4 September 1996 Accepted: 18 October 1996     

Preparation of monomodal polyelectrolyte complex nanoparticles of PDADMAC/poly(maleic acid-alt-alpha-methylstyrene) by consecutive centrifugation

We report on the refinement of anionic and cationic nanoparticles of nonstoichometric polyelectrolyte complexes (PEC) by consecutive centrifugation, which was studied by dynamic light scattering (DLS), atomic force microscopy (AFM), colloid titration and infrared spectroscopy (IR). PEC dispersions were prepared by mixing poly(diallyldimethylammonium chloride) (PDADMAC) and sodium poly(maleic acid-alt-alpha-methylstyrene) (PMA-MS) at the monomolar mixing ratio of n-/n+ = 1.50 (anionic PEC) and 0.66 (cationic PEC), respectively, and the polymer concentration of c(POL) = 0.002 M. The particle size (Rh), titrable charge amount, and IR spectra were determined for both dispersions in the original state, after the first centrifugation and after the second centrifugation. Freshly prepared PEC dispersions contained two different particle sizes: around 10-25 nm (small particles) and around 100 nm (large particles). Consecutive centrifugation of freshly prepared PEC dispersions resulted in the separation of highly charged excess polyelectrolyte (PEL) and small PEC particles from a low charged coacervate phase of the desired larger PEC particles. After the second centrifugation, the coacervate phase of both dispersions PEC-1.50 and PEC-0.66 consisted of monomodal particles sizing around 100 nm. These results were supported by AFM measurements on the respective dispersions deposited on glass plates. PEC-1.50 particles tended to adopt slightly smaller sizes ( approximately 90 nm) in comparison to PEC-0.66 ones (approximately 110 nm). No significant influence of the PDADMAC molecular weight on the particle size was found. IR spectroscopy showed changes in the environment of the carboxylate groups of PMA-MS by consecutive centrifugation. The centrifuged PEC-1.50 dispersions showed remarkable long-term stability over more than a year. The high macroscopic stability of the studied PEC dispersions is presumably due to repulsive electrostatic interparticle interactions and attractive hydrophobic intraparticle interaction. The introduced monomodal PEC particles might be projected as latex analogues or as nanocarriers for drugs and proteins.     

Structure–property study of waterborne,polyurethane acrylate dispersions based on hyperbranched aliphatic polyester for UV-curable coatings

A series of waterborne, hyperbranched polyurethane acrylates for aqueous dispersions (WHPUDs) based on hydroxy-functionalized hyperbranched aliphatic polyester Boltorn H20 were synthesized and characterized by Fourier transform infrared spectroscopy (FTIR). The aqueous dispersions were electrostatically stabilized with carboxyl groups incorporated into their structures, which were neutralized by triethylamine (TEA). The effects of chemical structures of end groups on various properties of WHPUDs, such as particle size, interfacial tension, and rheological behavior were investigated. The average particle sizes of aqueous dispersions, 43–237 nm, were determined by laser light scattering. Owing to the enlargement of the stabilization site, the particle size decreased as the content of carboxyl group, degree of neutralization, and dielectric constant of the dispersion medium increased. Moreover, the surface tension of aqueous dispersions of WHPUDs decreased as the TEA/COOH mole ratio and degree of neutralization increased. The investigations of the rheological behavior of the WHPUDs suggested that all the dispersions belong to pseudoplastic fluids, and each of them has viscosity much lower compared with the commercial water-based resin EB 2002.     

Preparation and characterization of waterborne poly(urethane urea) with well‐defined hard segments

A series of polyester‐based poly(urethane urea) (PUU) aqueous dispersions with well‐defined hard segments were prepared from polyester polyol, 4,4′‐diphenylmethane diisocyanate, dimethylolpropionic acid, 1,4‐butanediol, isophorone diisocyanate, and ethylenediamine. These anionic‐type aqueous dispersions had good dispersity in water and were stable at the ambient temperature for more than 1 year. For these aqueous dispersions, the particle size decreased as the hard‐segment content increased, and the polydispersity index was very narrow (<1.10). Films prepared with the PUU aqueous dispersions exhibited excellent waterproof performance: the amount of water absorption was as low as 5.0 wt %, and the contact angle of water on the surface of this kind of film was as high as 103° (this led to a hydrophobic surface). The water‐resistant property of these waterborne PUU films could be well correlated with some crystallites and ordered structures of the well‐defined hard segments formed by hydrogen bonding between the urethane/urethane groups and urethane/ester groups, as well as the degree of microphase separation between the hard and soft segments in the PUU systems. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2606–2614, 2005     

Restricted self-diffusion in an aqueous solution of poly(ethylene oxide) poly(propylene oxide) poly(ethylene oxide) triblock copolymer

 The self-diffusion behavior of a triblock copolymer (PEO–b– PPO–b–PEO) in an aqueous solution of 20% (m/m) was investigated during a temperature-induced phase transition from liquid to gel state using pulsed field gradient NMR and static light scattering. The measured self-diffusivity shows a strong dependence on the observation time in the gel phase indicating the existence of diffusion barriers in the size range of about 0.6 μm. Additional static light-scattering measurements show a structure in the same size range of several hundred nanometers, which is far above molecular or micellar sizes and thus, has to be caused by larger clusters. The similarity in the space scales suggests that the restriction of molecular propagation is correlated with the grain boundaries between the domains of the poly-crystalline structure formed by the arranged micelles. Received: 28 October 1996 Accepted: 21 March 1997     

Role of surface modification of colloidal CdSe quantum dots on the properties of hybrid organic–inorganic nanocomposites

In this work, tri-octyl phosphine/tri-octyl phosphine oxide (TOPO)-capped cadmium selenide (CdSe) quantum dots (QDs) of varied sizes (5–9 nm), prepared by varying the input Cd:Se precursor ratio using chemical route, were dispersed in conducting polymer matrices viz. poly[2-methoxy, 5-(2-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) and poly(3-hexylthiophene) (P3HT). By using a binary solvent mixture (pyridine–chloroform), homogeneous dispersion of CdSe nanocrystals in polymers (MEH-PPV, P3HT) could be realized. The properties of the resulting dispersions could be tailored by the composition and concentration of QDs in polymer. The emission and structural properties of polymer–CdSe nanocomposites are found to be dependent on the crystallite size and morphology of CdSe nanocrystallites. An effective quenching of photoluminescence emission in the polymer nanocomposite was observed for smaller CdSe quantum dots (size ∼6 nm) as compared to larger CdSe quantum dots (size ∼9 nm), thus ensuring efficient charge transfer process across the polymer–CdSe interface in the former case. The incomplete quenching, particularly for MEH-PPV:CdSe nanocomposites, could be as a result of insufficient coverage of polymers on the surface of CdSe nanocrystallites, mainly due to phase segregation for TOPO-stripped CdSe nanocrystallites. The superior morphology and optical properties of polymer nanocomposite (P3HT:CdSe QDs) could play a pivotal role for the realization of effective charge separation and transport in hybrid solar cells.     

Preparation and characterization of cross-linked hyaluronan nanoparticles

The present investigation describes the synthesis and characterization of novel biodegradable nanoparticles based on hyaluronic acid (HA). The diamine, 2,2′(ethylenedioxy)bis(ethylamine) was used for cross-linking of the HA linear chains. The condensation reaction of amino groups and pendant carboxyl groups of HA was performed in aqueous media at room temperature using water-soluble carbodiimide. The prepared nanosystems, aqueous solutions, or dispersions of nanoparticles were stable, transparent, or mildly opalescent systems depending on the ratio of cross-linking, findings consistent with values of transmittance above 77%. The structure of products was determined by nuclear magnetic resonance spectroscopy, and the particle size was identified by laser light scattering (DLS) and transmission electron microscopy (TEM) measurements. Particle size measured by TEM varied less than 130 nm; in the swollen state, the average size of the particles measured by DLS was in the range of 30–140 nm depending on the ratio of cross-linking and the molecular weight of HA. Formation of cross-linked nanoparticles results in a viscosity drop compared to the viscosity of the corresponding solution of the HA, and this trend becomes decreasingly appreciable as the molecular weight of HA decreases.     

Preparation of nanostructure hydroxyapatite scaffold for tissue engineering applications

Hydroxyapatite due to its good biocompatibility and similar chemical composition to the mineral part of bone has found various applications in tissue engineering. Porous hydroxyapatite has high surface area, which leads to excellent osteoconductivity and resorbability, providing fast bone ingrowth. In this study, highly porous body of nanostructure hydroxyapatite was successfully fabricated via gelcasting method. The pure phase of hydroxyapatite was confirmed by X-ray diffraction. The result of scanning electron microscopy analysis showed that the prepared scaffold has highly interconnected spherical pores with a size in the range 100–400 μm. The crystallite size of the hydroxyapatite scaffold was measured in the range 30–42 nm. The mean values of true (total) and apparent (interconnected) porosity were calculated in the range 84–91 and 70–78%, respectively. The maximum values of compressive strength and elastic modulus of the prepared scaffold were found to be about 1.5 MPa and 167 MPa, respectively, which were achieved after sintering at 1,000 °C for 4 h. Transmission electron microscopy analysis showed that the particle sizes are smaller than 80 nm. In vitro test showed good bioactivity of the prepared scaffold. The mentioned properties could make the hydroxyapatite scaffold a good candidate for tissue engineering applications, especially applications that did not need to stand any loading.     

Preparation and optical properties of blue-emitting colloidal CdS nanocrystallines by the solvothermal process using poly (ethylene oxide) as the stabilizer

Blue-emitting colloidal CdS nanocrystals have been synthesized through the solvothermal reaction of cadmium acetate and thiourea in N,N-dimethylformamide using poly(ethylene oxide; PEO) as the stabilizing polymer. The as-prepared CdS colloids were stable at ambient conditions for several weeks. The PEO-stabilized CdS colloids showed a narrow fluorescence band with the maximum at about 420 nm and thus emitting blue fluorescence under the ultraviolet (UV) lamp. A common red shift of fluorescence band is not detected for the prepared CdS colloids in the study, indicating that PEO-stabilized CdS NCs possess few crystalline defects on their surface. In addition, transmission electron microscope micrographs reveal that the sizes of CdS NCs are between 4.4 to 5.4 nm with small standard deviations from 0.5 to 0.7 nm. The particle growth kinetics was studied by monitoring UV-visible absorption onsets versus the reaction time and was found to nearly follow the Lifshitz–Slyozov–Wagner theory for the Ostwald ripening mechanism.     

Soluble poly (aryl ether)s containing naphthalene pendant group: synthesis, characterization and electrospinning

Two soluble poly(aryl ether)s were prepared conveniently from bis(4-hydroxy-3,5-dimethylphenyl)naphthylmethane (1) and two activated dihalide monomers including 4,4′-difluorobenzophenone and bis(4-chlorophenyl)sulfone by an aromatic nucleophilic substitution. The bulky naphthyl and tetramethyl pendant groups in the polymer backbone could decrease the packing density and intermolecular interaction of macromolecular chain and make these poly(aryl ether)s show a good solubility. They all could be dissolved in CHCl₃, CH₂Cl₂ and tetrahydrofuran at room temperature with a dissolvability of more than 10 wt%. Furthermore, the poly(aryl ether)s could be electrospun into microfiber (10–15 μm) with nanopores (200–350 nm). The morphologies of these fibers were characterized by scanning electron microscopy. The porous morphology on the fiber surface was also investigated using scanning probe microscope.     

Surfactant assisted preparation and characterization of carboxymethyl cellulose Sn(IV) phosphate composite nano-rod like cation exchanger

Carboxymethyl cellulose Sn(IV) phosphate composite nano-rod like cation exchanger with diameter in the range of 20–40 nm, length in the range of 100–150 μm and particle size in the range of 21–38 nm have been successfully prepared by surfactant assisted sol–gel method. Scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, fourier transform infra red spectroscopy and thermogravimetric analysis-differential thermal analysis studies were carried out to study the structure and morphology of this composite nano-rod like cation exchanger. Freundlich adsorption isotherm is well fitted for the adsorption of pyridine on the surface of this composite nano-rod like cation exchanger. The thermodynamic parameters such as Freundlich constant, thermodynamic equilibrium constant (K ₀), standard free energy changes (ΔG ⁰), standard enthalpy changes (ΔH ⁰) and standard entropy changes (ΔS ⁰) have been evaluated. These parameters indicated that the adsorption of pyridine on the surface of composite nano-rod like cation exchanger was feasible, spontaneous and exothermic in nature which suggests for the potential application of pyridine removal from water.     

Morphological characteristics of modified freeze-dried poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) microspheres studied by optical microscopy,SEM, and DLS

Influence of the initiator and additional hydrophobic copolymer on the morphology of thermosensitive poly(N-isopropylacrylamide) (pNIPAM) microspheres, and their presumed application for the stabilization of biologically active molecules were evaluated in this study. Three different types of pNIPAM were synthesized, applying various components: PN1 is a polymer with terminal anionic groups resulting from potassium persulfate initiator; PN2 was synthesized with a 2,2′-azobis(2-methylpropionamidine) dihydrochloride initiator introducing cationic amidine terminal groups; in the PN3 polymer, anionic terminals were implemented, however, increased hydrophobicity was maintained using N-tert-butyl functional groups. Turbidity measurements of the obtained dispersions confirmed specific thermosensitivity of synthesized microspheres in the range of 32–33°C. The polymerization course was proved by infrared spectroscopy and ¹H NMR assessments, whereas the size of the synthesized microspheres, expressed as planar area, was evaluated by dynamic light scattering (DLS), scanning electron microscopy (SEM) and optical microscopy (OM). The respective surface patterns of the freeze-dried microspheres were evaluated by SEM. Planar area of the synthesized macromolecules was in the range between 0.41–3.22 μm, depending on the substrates composition and the method applied for the measurements. The assessments performed in the dry stage gave higher values of the diameter and planar area of the observed microspheres. The measured diameter and planar area increased in the following order for the PN3 microspheres: DLS, OM, SEM. In the case of PN1 and PN2, the observed diameters were positioned as: DLS, SEM, OM. These differences were assigned both to varied intramolecular hydrophobic-hydrophilic interactions of the polymer chains and to the environment, i.e. low pressure in the SEM conditions and aqueous solvent in the DLS measurements. The observed gaps in the freeze-dried PN2 polymer resulted in an attempt to evaluate the application of this polymer for mechanical stabilization of certain macromolecules or nanocrystals in the size range between 10 nm and 20 nm.     

Preparation of hollow poly(divinyl benzene) particles with multiple holes in the shell by microsuspension polymerization with the SaPSeP method

Hollow polymer particles with multiple holes in the shell were prepared by aqueous microsuspension polymerization of micrometer-sized, monodisperse divinylbenzene/n-hexadecane droplets in the presence of sodium dodecyl sulfate (SDS) at concentrations above 4 mM utilizing the Self-assembling Phase-Separated Polymer (SaPSeP) method developed by the authors. The total surface area of the holes per particle increased with an increase in the SDS concentration. At [SDS] = 10 mM, “flower-like” non-spherical particles were formed. Part CCCXV of series “Studies on Suspension and Emulsion”     

Synthesis of large-pore SBA-15 silica using poly(ethylene oxide)-poly(methyl acrylate) diblock copolymers

Poly(ethylene oxide)-poly(methyl acrylate) diblock copolymers with narrow molecular weight distributions were synthesized using atom transfer radical polymerization. The copolymers were used as micellar templates for the synthesis of mesoporous silicas. The products were characterized using small-angle X-ray scattering, transmission electron microscopy (TEM) and nitrogen adsorption. The obtained silicas exhibited two-dimensional hexagonal structures of cylindrical mesopores, and thus can be classified as SBA-15 silicas. In some cases, the size of ordered domains was very small. The (100) interplanar spacings were 13–17 nm, depending on the size of the diblock copolymer used and on the synthesis conditions. Nitrogen adsorption showed that the silicas exhibited specific surface areas of 350–800 m² g⁻¹, pore volumes ∼1 cm³ g⁻¹, and narrow pore size distributions. The BJH (nominal) pore diameters were up to ∼20 nm, but actual diameters of cylindrical pores are expected to be somewhat smaller. In many cases, the mesopores exhibited constrictions.     

Thermosensitive phase behavior and drug release of in situ gelable poly(N-isopropylacrylamide-co-acrylamide) microgels

In situ gelable poly(N-isopropylacrylamide-co-acrylamide) microgels were prepared by precipitation polymerization in the presence of various amounts of N,N′-methlenebisacrylamide as a crosslinker. The diameters of microgels were in the range of 200–300 nm with narrow distributions as determined by photo correlation spectroscopy. The equilibrium swelling ratio and thermosensitive properties of the microgels increased with decreasing crosslinker content. The volume phase transition of microgels dispersions at high concentrations were investigated by phase diagrams. The microgels dispersions experienced four phases when the temperature was increased: semitranslucent swollen gel, clear flowable suspension, cloud flowable suspension, and white shrunken gel. The related phase transition temperatures were influenced by crosslinker content and the concentration of the microgel dispersions. Herein, the gelation temperature was changed by more than 20 °C, shrinking temperatures were slightly changed by about 3 °C, and cloud point temperatures showed almost no change. The three phase transition temperatures of microgels dispersed in phosphate-buffered saline solutions were lower than that in water. As drug carriers, the release rates of bleomycin from bleomycin-loaded microgel dispersions exhibited diffusion control at human body temperature.     

Non-isothermal decomposition kinetics of NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles synthesized using egg white solution route

The thermal decomposition kinetics of nickel ferrite (NiFe₂O₄) precursor prepared using egg white solution route in dynamical air atmosphere was studied by means of TG with different heating rates. The activation energy (E _α) values of one reaction process were estimated using the methods of Flynn–Wall–Ozawa (FWO) and Kissinger–Akahira–Sunose (KAS), which were found to be consistent. The dependent activation energies on extent of conversions of the decomposition reaction indicate “multi-step” processes. XRD, SEM and FTIR showed that the synthesized NiFe₂O₄ precursor after calcination at 773 K has a pure spinel phase, having particle sizes of ~54 ± 29 nm.     

Magnetically loaded poly(methyl methacrylate-co-acrylic acid) nano particles

Magnetically loaded polymeric nano-particles carrying functional groups on their surface were prepared by a two-stage process. In the first stage, super-paramagnetic magnetite (Fe₃O₄) nano-particles were produced by a co-precipitation method from the aqueous solutions of FeCl₂·4H₂O and FeCl₃·6H₂O using a NaOH solution. The smallest size obtained was 40.9 nm with poly-dispersity index of 0.194 obtained by using a Zeta Sizer. The effects of Fe²⁺/Fe³⁺ molar ratio, stirring rate, temperature, base concentration, and pH on the particle size/size distribution and stability of the dispersions were examined. Increasing the relative concentration of Fe²⁺ ion and decreasing the stirring rate and pH increased the particle size, while the concentration of NaOH and temperature did not change the particle size significantly. Polymer coating was achieved by emulsion polymerization at high surfactant to monomer ratio of methyl methacrylate (MMA) and acrylic acid which were used as comonomers (comonomer ratio: 90/10 weight) with high surfactant to monomer ratio. The surfactant and initiator were SDS and KPS, respectively. Nano-particles in the range of 115 and 300 nm in diameter were produced depending on recipe. Increasing the Fe₃O₄/monomer and surfactant/monomer ratios, the KPS concentration caused a decrease in the average diameter. Magnetic properties of the nano-particles were obtained by electron spin resonance and vibrating-sample magnetometer. Most of the polymer-coated nano-particles exhibited super paramagnetic behavior.An erratum to this article can be found at     

Use of Gemini surfactants to stabilize TiO2 P25 colloidal dispersions

Photocatalytically active TiO₂ P25 nanoparticles, widely used for practical applications, were investigated. The nominal size of TiO₂ P25 nanoparticles is 21 nm, but they easily agglomerate in aqueous media, depending on pH and ionic strength. TiO₂ P25 aqueous dispersions were stabilized by alkanediyl-α,ω-bis-N-dodecyl-N, N′-dimethyl-ammonium bromide, cationic Gemini surfactant. The optimal conditions required to obtain stable dispersions, without formation of large agglomerates, were experienced. The stabilization of TiO₂ P25 nanoparticles by cationic Gemini surfactant was investigated in some details. Different amounts of Gemini surfactant were used, at concentrations between 1.0 and 250 × 10⁻⁶ mol L⁻¹, well below the critical micelle concentration. Dynamic light scattering and zeta potential analyses estimated the particle size and the dispersions stability. When the proper amount of Gemini surfactant was used, the resulting nanoparticles were still poly-disperse, but large agglomerates disappeared and were remarkably redispersible.