中国散裂中子源大功率可编程脉冲电源设计

在中国散裂中子源大功率可编程脉冲电源设计中,主回路采用绝缘栅双极型晶体管(IGBT)H桥串并联拓扑,错相工作方式,利用IGBT功率放大的特性,实现了电源高功率(60 MW)、高频率(1.843 2MHz)、高压(3.319 kV)和大电流(18 kA)的要求,并通过电源反馈控制系统,实现了电源的快速响应时间,使电源跟踪精度达到1.5%,满足指标要求。在电源研制中,解决了IGBT高压、大电流的均压和均流问题;由于IGBT工作在开关状态,为了消除谐波,利用多重化技术,得到了光滑的输出脉冲电流曲线;采用电流互感器的并联,实现了输出大电流的检测;电源的反馈控制策略采用比例和前馈运算,实现了电源输出波形对给定波形的快速跟踪。     

Antenna phase pattern measurements at millimeter wave frequencies using the differential phase method with only one power meter

The differential phase measurement method has been improved to need the use of only one power meter instead of three power meters. This enables accurate antenna phase pattern measurements with a simplified set-up, accompanied by the reduction in cost. All advantages of the differential phase measurement method are still also available, e.g. there is no need to phase lock oscillators or to use rotary joints. The measurement results for an antenna at 110 GHz are presented. A good agreement with earlier data was obtained.     

锁频锁相的高功率微波器件技术研究

综述了中国工程物理研究院应用电子学研究所锁频锁相的高功率微波器件最新研究成果,主要包括稳频稳相的相对论速调管放大器和注入锁相的相对论返波管振荡器.针对高功率长脉冲相对论速调管研究中遇到的问题,介绍了该放大器的束波互作用特点、杂频振荡抑制、脉冲缩短、高频段高功率运行、高增益等物理、设计与实验中的关键技术研究概况,使其功率、相位稳定性、增益等性能有了显著提高,S波段环形单注相对论速调管实现了高功率稳相输出,重频25 Hz运行时输出功率大于1 GW,脉宽大于150 ns、相位波动18°,高增益运行时在注入微波功率数kW条件下也实现类似功率和相位水平;采用同轴多注器件结构,突破了速调管高频段运行条件下高效率电子束引入和高功率束波转换技术等难题,使X波段相对论速调管在注入功率30 kW条件下实现了功率大于1 GW的放大输出,效率为34%,相位波动为15°.在掌握相对论返波管技术的基础上,利用返波管的高效率和结构紧凑的优点,开展了注入调制电子束锁相的相对论返波管研究,采用百kW级的种子微波实现了对GW量级输出微波的相位锁定.该研究结果对功率合成、粒子加速和多功能雷达等技术具有重要的推动作用.     

Coexistence of Self-pumped Phase Conjugation and Mutual-pumped Phase Conjugation in Ce:BaTiO3

Ｓｉｎｃｅｔｈｅｄｉｓｃｏｖｅｒｙｏｆｍｕｔｕａｌｐｕｍｐｅｄｐｈａｓｅｃｏｎｊｕｇａｔｉｏｎｉｎｐｈｏｔｏｒｅｆｒａｃｔｉｖｅｃｒｙｓｔａｌｓ,ａｎｕｍｂｅｒｏｆｄｉｆｆｅｒｅｎｔｔｙｐｅｓｏｆｍｕｔｕａｌｐｕｍｐｅｄｐｈａｓｅｃｏｎｊｕｇａｔｏｒｓｈａｖｅｂｅｅｎｆｏｕｎｄ,ｎａｍｅｌｙ,ｔｈｅｄｕａｌｐｈａｓｅｃｏｎｊｕｇａｔｅｍｉｒｒｏｒ(ＰＣＭ)[1],ｂｒｉｄｇｅＰＣＭ[2,3],ｉｎｃｏｈｅｒｅｎｔｂｅａｍｃｏｕｐｌｅｒ[4],ｂｉｒｄｗｉｎｇＰＣＭ[5],ｆｒｏｇｌｅｇＰＣＭ[6],ｆｉｓｈｈｅａｄＰＣＭ[…     

Coexistence of Self-pumped Phase Conjugation and Mutual-pumped Phase Conjugation in Ce∶BaTiO3

Self-pumped phase conjugation(SPPC) and mutual-pumped phase conjugation (MPPC) have been found to coexist in Ce∶BaTiO3 by using two coherent beams of 514.5nm wavelength from an argon ion laser. Both phase conjugations are of the stimulated backscattering and four-wave mixing type. For 7/6 incident power ratio and 26 mW total incident power,he shortest phase conjugate mirror formation time is 10s . Phase conjugate reflectivity of one the beams can reach 70%,hich is ～20% higher than the SPPC reflectivity using only one beam. When the total incident power is increased to 40 mW and the incident power ratio remains constant,a maximum phase conjugatate reflectivity of as much as 88% is obtained.     

湍流大气中斜程传输光场的相位特性

运用功率谱反演法对斜程传输大气湍流扰动相位屏进行了数值模拟。通过建立激光束初始畸变相位模型,从波前峰谷值和波前功率谱密度函数两个方面,对激光束通过大气湍流后的相位特性进行了研究,重点分析了湍流传输距离和天顶角对激光束波前相位分布的影响。研究结果表明:激光束在湍流大气斜程传输后,其波前相位会发生明显畸变,且空间高频相位较低频相位所占比例明显增加;通过湍流后的波前相位与传输距离及天顶角密切相关,传输距离越长,天顶角越大,相位畸变程度越大,高频相位所占比例越多。     

Optical phase conjugation by degenerate four-wave mixing in basic green 1 dye-doped gelatin film using He–Ne laser

Optical phase conjugation in gelatin film doped with basic green 1 has been measured using CW laser radiation (λ=632.8 nm) generated by He–Ne laser of total power 35 mW. The degenerate four-wave mixing (DFWM) experiment allowed for measurement of phase conjugate reflectivity as a function of dye concentration, backward beam intensity, forward beam intensity, probe beam intensity, mean pumping beam intensity and angle between the forward pumping beam and probe beam. For 1 mM concentration of basic green 1-doped gelatin film, 0.1% phase conjugate reflectivity has been observed.     

HIGH CONVERSION EFFICIENCY TANDEM KTP FREQUENCY DOUBLER

The two-piece tandem KTP frequency doubler with mutually perpendi-oular KZ planes has been studied both theoretically and experimentally.Its conversionefficiency of second harmonic generation(SHG)exceeds 80% and the dynamic range ismuch greater than that of monolithic KTP doubler at the laser power used in theexperiments.The experimental result shows that this doubler has excellent performancesand the second harmonic beam is elliptically polarized.     

Order parameter and its critical exponent for some binary mixtures showing induced nematic phase

Refractive index measurements as a function of temperature have been performed for an induced nematic binary system by means of thin prism technique. The temperature dependence of the birefringence (Δn) has been assessed from the measured refractive index data. A direct extrapolation method has been employed to determine the orientational order parameter for the investigated mixtures and the order parameter so obtained has also been compared with the mean field values. The Haller type fitting expression results in a relatively lower value of the order parameter critical exponent (β) compared to the theoretically predicted values. Therefore, a four-parameter power law expression, consistent with the mean field theory as well as the first-order character of the nematic–isotropic (N-I) phase transition have been used to explore the critical behavior of the order parameter near the N-I transition.     

Posterior capsular opacification and intraocular lens surface micro-roughness characteristics: an atomic force microscopy study

ObjectiveSurface roughness parameters of various intraocular lenses (IOLs) biomaterials using atomic force microscopy (AFM) are compared. Variation, if any, in the micro-roughness properties of different IOLs made up of the same biomaterial is also explored. Retrospective analysis of posterior capsular opacification (PCO) incidence has been followed up for a period of four years post IOL implantation to evaluate the correlation of PCO formation with surface roughness of IOLs.DesignExperimental materials study.Materials and participantsSurface characteristics of 20 different IOL models were assessed using AFM. These IOL models were made up of PMMA or HEMA or acrylic hydrophobic or acrylic hydrophilic or silicone. Retrospective analysis of PCO incidence in 3629 eyes of 2656 patients implanted with the same IOL models was performed.MethodsTopological characteristics of 20 different IOLs made up of 5 different biomaterials including (i) PMMA, (ii) HEMA, (iii) acrylic hydrophobic, (iv) acrylic hydrophilic and (v) silicone were evaluated using AFM in the tapping mode. Images were acquired with a resolution of 256 × 256 data points per scan at a scan rate of 0.5 Hz per line and a scan size of 10 × 10 μm. Rate of PCO formation in 3629 eyes of 2656 patients implanted with the five different IOL biomaterials was retrospectively analyzed.ResultsAFM images of IOL optic surfaces showed a collection of pores, grooves, ridges and surface irregularities. Surface roughness parameters of the IOL optics were significantly different on comparing lenses of different materials. Acrylic hydrophobic IOLs had minimum surface roughness while acrylic hydrophilic IOLs showed the highest surface roughness. Different IOL models of the same biomaterial showed varied topological roughness characteristics. Retrospective analyses of PCO formation rate after IOL implantation was carried out, which revealed that rate of PCO incidence, was directly proportional to the increase in surface micro-roughness of IOLs.ConclusionsAFM is a powerful technique for the topological characterization of IOLs. Acrylic hydrophobic IOLs showed minimum surface roughness properties as well as minimum PCO incidence over a period of four years post implantation. It is, therefore, tempting to consider acrylic hydrophobic IOLs over other IOL biomaterials as the ideal biocompatible material for lowering PCO incidence. These results suggest an urgent need for manufacturers to optimize the various steps involved in the fabrication of IOLs.     

Ag‐doped TiO2 enhanced photocatalytic oxidation of 1,2‐cyclohexanediol

The superiority of silver‐doped titania for photocatalytic oxidation (PCO) of organic compounds inspired us to investigate PCO of 1,2‐cyclohexanediol. Ag/TiO₂ was prepared, characterized (nanosize 19–24 nm) and used for oxidation of 1,2‐cyclohexanediol (1) in acetonitrile. The photolysate was analyzed using GC and GC/MS techniques. The PCO products are 2‐hydroxylcyclohexanone (2), 1,2‐cyclohexandione (3), 2‐cyclohexenone(4), cyclohexanone (5), and adipic acid (6).The formation of electron–hole pair at the surface of the catalyst followed by oxidation reactions was the suggested mechanism. Kinetic studies revealed first‐order mechanism for PCO of 1 and rate constant (k) = ?0.145 h^–1. Copyright © 2012 John Wiley & Sons, Ltd.     

高功率激光通过有中心遮拦透镜的聚焦

用广义惠更斯－菲涅耳衍射积分对有振幅调制和位相畸变的高功率激光束通过有中心遮拦透镜的聚焦特性作了详细研究，并对焦面处光束的可聚焦性进行了讨论。数值计算结果表明，功率集中度与光阑的遮拦比，光束截断参数以及振幅调制和位要畸变参数等有关。     

LHCD系统微波激励源性能优化设计

使用数字锁相环技术实现一定带宽内高精度可调节的频率输出,解决了速调管长期工作后响应频率发生偏移,模拟锁相环无法工作在系统最佳频率的问题;在移相器后增加功率幅度控制电路,保证了线性放大器的输出功率不会受到相位调节的影响;设计了一种基于数模转换(D/A)技术与微波电调技术相结合的波形控制单元,解决了激励源输出波形不可控的问题。通过以上三方面的改进,完成了HL-2M装置LHCD系统微波激励源的性能优化设计。     

角锥棱镜阵列谐振腔的输出特性

 角锥棱镜阵列具有溯源反射和准相位共轭两大特点,可在一定程度上补偿高平均功率固体激光器的热畸变。但由于这种角锥棱镜阵列自身的缺陷和由它构成的谐振腔输出激光模式众多的特点,限制了其在谐振腔中的应用。分析了角锥棱镜阵列谐振腔产生多模输出的原因,提出了采用腔内滤波的方法实现单模输出。理论模拟和实验研究结果表明：利用该方法可较好地改善阵列角锥棱镜谐振腔的输出特性,获得了近5倍衍射极限的输出。     

Improved analysis of dispersion compensation using differential time delay for high-speed long-span optical link

A dispersion-compensation technique using differential time delay has been analyzed for a high bit rate dispersive limited system using higher order dispersion terms. The technique is based on splitting the power spectrum into upper and lower parts, corresponding to the two modulation sidebands, and delaying one of these with respect to the other. RMS, phase deviation, dimension free chirp parameter, and figure of merit have been evaluated due to higher order dispersion terms for ideal and realistic optical communication systems. It has been shown that the transmission distance could be enhanced to fourfold, sixfold, and eightfold when the compensation has been performed using second-, third-, and fourth-order dispersion (20D, 30D, and 40D) terms.     

Bulk viscous cosmology in early Universe

The effect of bulk viscosity on the early evolution of Universe for a spatially homogeneous and isotropic Robertson-Walker model is considered. Einstein’s field equations are solved by using ‘gamma-law’ equation of state p = (γ − 1)ρ, where the adiabatic parameter gamma (γ) depends on the scale factor of the model. The ‘gamma’ function is defined in such a way that it describes a unified solution of early evolution of the Universe for inflationary and radiation-dominated phases. The fluid has only bulk viscous term and the coefficient of bulk viscosity is taken to be proportional to some power function of the energy density. The complete general solutions have been given through three cases. For flat space, power-law as well as exponential solutions are found. The problem of how the introduction of viscosity affects the appearance of singularity, is briefly discussed in particular solutions. The deceleration parameter has a freedom to vary with the scale factor of the model, which describes the accelerating expansion of the Universe.      

Study on optical characterization of TGB and reentrant smectic-A phases in binary mixture of two liquid crystals

In this work, our investigation is to study the optical and thermal properties of the binary mixture of cholesteric and nematic compounds, namely, cholesteryl nonanoate and p-methoxybenzylidene-p-ethylaniline, which exhibits a very interesting liquid crystalline twisted grain boundary (TGB) phase and reentrant smectic-A phase. The chiral liquid crystalline TGB phases and reentrant smectic-A phases have been observed at different concentrations and at different temperatures. The existence of TGB and reentrant smectic-A phases is confirmed by differential scanning calorimetry and optical microscopic studies. The variation of optical anisotropy has been discussed. The helical pitch of the cholesteric phase has also been discussed.     

高精度大功率双向可调电源设计

为满足ITER传感器测试平台对电源高稳态精度、高压及大电流性能需求,通过H桥级联载波移相方式对大功率电源进行设计,并进行谐波分析,有效地提高变流器等效开关频率,改善输出波形。经实验验证,取得较好效果。     

基于外差法的光纤激光器相干合成

采用波长1064 nm,功率为1 W的种子激光实现了两路光纤激光的相干合成,采用了两只保偏光纤准直器接收两路光干涉信号,与利用透镜直接把干涉信号会聚在探测器上相比,这种耦合方式得到的光干涉信号的条纹对比度更高。对相位噪声以及相位噪声的带宽进行了研究,结果表明,相位噪声由电信号串扰以及环境扰动产生。通过人为拨动光纤来增加相位噪声带宽,当相位噪声带宽增加时,相位控制精度下降。提出了提高相位控制精度的方法,实验获得了桶中功率为21.3%、斯特列尔比为79%、相位控制精度为0.008的相干合成效果。     

Improved analysis of dispersion compensation using differential time delay for high-speed long-span optical link

Abstract

A dispersion-compensation technique using differential time delay has been analyzed for a high bit rate dispersive limited system using higher order dispersion terms. The technique is based on splitting the power spectrum into upper and lower parts, corresponding to the two modulation sidebands, and delaying one of these with respect to the other. RMS, phase deviation, dimension free chirp parameter, and figure of merit have been evaluated due to higher order dispersion terms for ideal and realistic optical communication systems. It has been shown that the transmission distance could be enhanced to fourfold, sixfold, and eightfold when the compensation has been performed using second-, third-, and fourth-order dispersion (20D, 30D, and 40D) terms.