Characterization of volume strain of poly(vinylidene fluoride) under creep test

Poly(vinylidene fluoride) (PVDF) was subjected to a creep test performed at constant true stress. The use of an original method to control and adjust, in real time, the stress allowed the assessment of volume changes occurring during the test. The adaptation of Bucknall's model enabled us to excerpt the component related to microstructural modifications from the whole volume strain. Mechanisms inducing volume strain are temperature dependent. Above ?40 °C and below 80 °C, that is, in between both glass transitions of PVDF, a linear increase of volume strain was observed as a result of polymer damage via the crazing phenomenon. In addition, this region is characterized by the presence of two distinct domains that could be attributed to either nucleation and propagation of voids or to an increase of the number of potential sites for nucleation resulting from microstructural modifications taking place during the test. On the contrary, above the secondary glass transition, a regular decrease of volume strain was observed. It was assigned to a material densification as a result of molecular orientation of the amorphous chain segments. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1754–1759, 2002     

Components of microstrain in polyethylene

Tensile microstrain was measured in high‐density polyethylene with a precision of 2 × 10^?7 for strains up to 10^?4 in the temperature range of 17–28 °C over a range of strain rates. The total strain was partitioned into three of the following components: (1) elastic, (2) amorphous, and (3) dislocation. Also, their respective dependence on stress was determined. Measurements of the area of the hysteresis loops gave the energy loss per cycle from which the frictional stress on the amorphous flow and the dislocations was determined. Although the amorphous strain originated at zero stress and was dependent on the temperature and strain rate, the dislocation motion was activated above acritical stress and independent of temperature and strain rate within the scope of these experiments. The viscosity of the amorphous flow was determined. The effect of 5 Mrd γ irradiation on the micro‐deformation behavior was not appreciable. About 80 Mrd reduced the amorphous flow by about 30% and increased the stress to activate the motions of the dislocations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2693–2701, 2002     

Bimodal molecular weight distribution formed in the emulsion polymerization of ethylene

It is known that the molecular weight distribution (MWD) formed in an emulsion polymerization of ethylene can be bimodal. However, the origin of the bimodality has not been elucidated. In this article, a Monte Carlo simulation is conducted, mostly with parameters reported in the literature. The simulated MWDs are bimodal because of the limited volume effect; that is, the high molecular weight profiles are distorted by the small particle size, which is comparable to the size of the largest branched polymer molecule in a particle. The simulated MWDs agree reasonably well with the experimentally obtained MWDs. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3426–3433, 2002     

Volume changes under strain resulting from the incorporation of rubber granulates into a rubber matrix

The strength of an elastomer is in part determined by the size of the intrinsic flaws that are present. It has been observed that the incorporation of rubber granulates into a virgin matrix results in a reduction in strength and this has previously been attributed to an increase in the intrinsic flaw size. The precise nature of this intrinsic flaw is the subject of this investigation. Fundamental questions concerning the change in flaw size with strain and the reduction in strength resulting from a weaker interface have been investigated using volume change experiments. Initial experiments on carbon black filled rubber with no granulates incorporated have shown no significant volume change under strain. This contrasts with granulate filled materials whose experimentally measured volume changes with strain were seen to be substantially greater. Microstructural finite element analysis has revealed how this change in volume might result from a net increase in the flaw size with increasing strain. This work suggests that flaw size increases in a characteristic way with strain for materials where the matrix and granulates have a similar modulus, whereas a modulus mismatch between the matrix and the recycled granulate results in much larger volume changes and hence greater flaw size which also appears to increase with strain. This work emphasizes the importance in practical applications of matching the modulus of recycled granulate materials to that of the new virgin material in the matrix. This article introduces a novel technique for examining small changes in the interfacial bonding mechanisms under strain such as that caused by surface modification techniques. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3169–3180, 2007     

Oxygen‐barrier properties of cold‐drawn polyesters

The improvement of oxygen‐barrier properties of glassy polyesters by orientation was examined. Poly(ethylene terephthalate) (PET), poly(ethylene naphthalate), and a copolymer based on PET in which 55 mol % of the terephthalate was replaced with bibenzoate (PET‐BB55) were oriented by constrained uniaxial stretching. In a fairly narrow window of stretching conditions near the glass‐transition temperature, it was possible to achieve uniform extension of the polyesters without crystallization or stress whitening. The processes of orientation and densification correlated with the conformational transformation of glycol linkages from gauche to trans. Oxygen permeability, diffusivity, and solubility decreased with the amount of orientation. A linear relationship between the oxygen solubility and polymer specific volume suggested that the cold‐drawn polyester could be regarded as a one‐phase densified glass. This allowed an analysis of oxygen solubility in accordance with free‐volume concepts of gas permeability in glassy polymers. Orientation was seen as the process of decreasing the amount of excess‐hole free volume and bringing the nonequilibrium polymer glass closer to the equilibrium (zero‐solubility) condition. Cold drawing most effectively reduced the free volume of PET‐BB55. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 862–877, 2002     

Phase equilibrium and diffusion of solvents in polybutadiene: A capillary‐column inverse gas chromatography study

The capillary‐column inverse gas chromatography method was used to measure the diffusion and partition coefficients of ethylbenzene, styrene, and acrylonitrile in polybutadiene (PBD) at infinite dilution of the solvents. Experiments were performed over a temperature range of 50–125 °C. At temperatures well above the glass‐transition temperature of PBD, the diffusivities were correlated using an Arrhenius expression. The Arrhenius parameters in turn were intercorrelated and shown to be a function of the occupied volume, thus providing a method for predicting the diffusion of other solvents in the same polymer. Further, the activation energy was predicted using the Duda‐Vrentas free‐volume approach. The activation energy thus obtained was compared with the activation energy of the Arrhenius approach. The weight‐fraction activity coefficient data were compared to the predictions of the group contribution, lattice‐fluid equation‐of‐state, and the UNIquac Functional‐group Activity Coefficient (UNIFAC) free‐volume models. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1046–1055, 2002     

Large tensile deformation behavior of oriented high‐density polyethylene: A correlation between cavitation and lamellar fragmentation

Oriented high‐density polyethylene (HDPE), prepared by melt extrusion drawing, has been employed to address the correlation between cavitation and lamellar fragmentation at large strain. This has been done by investigating the volume strain, elastic recovery properties, and microscopic morphology. The results indicate that the reversible volume strain becomes saturation at a true strain of about 0.3, which is essentially consistent with the critical one related to lamellar fragmentation (point C). Morphological observations on the deformed samples provide structural insights into above deformation behaviors. Enlarged voids are hard to recover due to dominant plastic deformation of crystals once lamellar fragmentation sets in and thus a transition of reversible volume strain with strain is presented. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1202–1206, 2008     

Modeling the failure of an adhesive layer in a peel test

The failure of an adhesive layer in a 180° peel test is analyzed by the modeling of the peel as an elastica. The adhesive is assumed to fail by a process of cavitation and fibrillation. The resistance of the fibrillated material to deformation gives rise to a rate‐dependent peel force F. Governing equations, which take into account the large deformation of the fibrillated materials, are derived. Numerical solutions are obtained for the special case of a linear, viscous adhesive. Assuming a critical strain failure criterion for the fibrils, we show that the peel rate is inversely proportional to the square root of the adhesive thickness and directly proportional to F^3/4. The connection between the peel test and the tack test is also discussed. The maximum traction on the peel arm is found to be directly proportional to the peel force and inversely proportional to the adhesive thickness. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2277–2291, 2002     

Effects of humidity on Young's modulus in poly(methyl methacrylate)

Tensile tests on poly (methyl methacrylate) (PMMA) were conducted to clarify the effects of humidity and strain rate on tensile properties, particularly Young's modulus. Prior to the tensile tests, specimens were kept under various humidity conditions at 293 K, which were the same as the test conditions, for a few months to adjust the sorbed water content in the specimens. The tensile tests were performed under each humidity condition at three different strain rates (approximately 1.4 × 10^?3, 1.4 × 10^?4, and 1.4 × 10^?5 s^?1). Stress‐strain curves changed with humidity and strain rate. Young's moduli were also measured at small applied stresses (below 6.7 MPa) under various humidity conditions at 293 K. Young's modulus decreases linearly with increasing humidity and a decreasing logarithm of strain rate. These results suggest that Young's modulus of PMMA can be expressed as a function of two independent parameters that are humidity and strain rate. A constitutive equation for Young's modulus of PMMA was proposed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 460–465, 2002; DOI 10.1002/polb.10107     

Positron annihilation studies of poly(N‐isopropyl acrylamide) gel in mixed solvents

Positron annihilation lifetime spectroscopy was used to characterize the reentrant volume‐phase‐transition behavior of poly(N‐isopropyl acrylamide) hydrogel in an ethanol/water mixed solvent. The polymer gel was synthesized with γ irradiation. The ortho‐positronium lifetime (τ₃) in the gel slowly increased with an increase in the ethanol content in the mixed solvent. τ₃ was not influenced by the volume phase transition. The ortho‐positronium intensity decreased with the collapse of the gel in an approximately 10% ethanol/water mixture. When swelled in pure ethanol, τ₃ initially increased with the solvent amount in the gel, showing the destruction of intramolecular hydrogen bonding and the relaxation of polymer chains. The lower critical solution temperature of the gel in the 10% ethanol/water mixture was lower than that in pure water, and τ₃ for various solvent contents showed behavior similar to that seen in pure solvent. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1028–1036, 2002     

Friction and damage in the scratching of poly(n‐butyl acrylate) films

Scratch testing was performed on poly(n‐butyl acrylate) (PnBA) films with a sapphire indenter with a spherical tip (76 μm in radius). For uncrosslinked PnBA film, the surface of which is sticky, the horizontal or scratching force decreases with decreasing normal load and has a residual value (～ 6 mN) as the normal load approaches zero. The relation between the scratching force and normal load can be understood by finite element computation based on the Johnson–Kendall–Roberts theory under the assumption that the scratching force is proportional to the contact area, which depends on the normal load. With increasing driving speed, the scratching force shows a power relation with speed indicating a rate process. For crosslinked PnBA film, which behaves as an elastomer, the horizontal force approaches zero at zero normal load. Below a critical normal load, which depends on the thickness of the film, the crosslinked film recovers elastically after being scratched. Above the critical load, the film is damaged and, depending on its thickness, shows two distinct damage mechanisms. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 585–592, 2002; DOI 10.1002/polb.10117     

Complex formation of polyethyleneimine with copper(II), nickel(II), and cobalt(II) ions

An influence of the structure of a globule of polyethyleneimine on the complex formation of one with the copper(II), nickel(II), and cobalt(II) ions is described. A change of the coordination number from the pH of solution for complexes of ethylenediamine, diethylenetriamine, and polyethyleneimine with metal ions was found. The fraction of monomer links, bound with metal ions, depends on the volume of the globule of macromolecule as well as the condition of the proceeding reaction. The reaction of complex formation is controlled by the diffusion of metal ions into the polymer globule in solution. The effective equilibrium constants of complex formation were found. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 914–922, 2002; DOI 10.1002/pola.10157     

Effect of the tail‐group length and degree of polymerization on the order parameter of side‐chain liquid‐crystalline polymethacrylates containing phenylbenzoate mesogenic groups

The orientation of the side‐chain liquid‐crystalline polymers (LCP) containing phenylbenzoate mesogenic groups in the magnetic field was examined with ²H NMR spectroscopy. The influence of the degree of polymerization as well as the length of the methylene tail group (n = 1–4) have been established. The decrease of the order parameter S of the LCPs with an increased length of the tail group was found. The order parameter S of LCPs does not depend on the degree of polymerization. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2044–2048, 2002     

Morphology and orientation during the deformation of segmented elastomers studied with small‐angle X‐ray scattering and atomic force microscopy

Small‐angle X‐ray scattering (SAXS), atomic force microscopy (AFM), and other techniques were combined in a study of segmented thermoplastic elastomers (Pebax) containing poly(tetramethylene oxide) soft segments and hard blocks of nylon‐12. AFM was used to provide real‐space resolution of the morphology during tensile elongation and after subsequent relaxation. Nanofibril formation, starting at strains of about 1.5×, was characterized in detail, showing the evolution of the number, orientation, and size of these highly stressed load‐bearing fibrils that dominated the mechanical properties. AFM results were combined with two‐dimensional SAXS data to develop a model considering the breakup of the original ribbonlike nylon‐12 lamellae in combination with progressive reformation and orientation of highly stressed fibrils. The complex changes in the two‐dimensional SAXS images included a distorted arc pattern due to increased spacing of the lamellae in the stretch direction at low strains, with an evolution to completely different patterns dominated mainly by intrafibrillar and interfibrillar scattering contributions. Between stretch ratios of 1.5 and 2.3× original lamellae were progressively broken up, and by 3.2×, all lamellae independent of the initial orientation were broken into smaller crystals with low aspect ratios. The results were combined with differential scanning calorimetry and birefringence data taken on films under strain to obtain insight into the microscopic basis for strain softening and plastic deformation in Pebax and related segmented polymers. Birefringence cycling with strain provided a consistent picture with the other techniques for understanding the redistribution of stress on a nanoscopic scale during deformation and relaxation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1727–1740, 2002     

Ultimate tensile behavior of linear polyethylene solids

The influence of the elongation rate and temperature on the ultimate tensile properties of melt‐crystallized linear polyethylene solids was investigated, with a double‐edge‐notched specimen to avoid necking, in which uniform deformation could be assumed throughout the experiment. The data on ultimate properties such as the tensile strength and elongation at break for different temperatures could be superimposed, by shifts along the elongation rate axis, to give a master curve as a function of the time to rupture. The shift factors obtained from the superpositioning of both the tensile strength and ultimate strain took the form of the Williams–Landel–Ferry equation. As a result, the ultimate data provided a failure envelope curve that made it possible to predict rupture times when the tensile tests were conducted under any experimental conditions. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2018–2026, 2002     

Preparation and characterization of a nanoscale poly(vinyl alcohol) fiber aggregate produced by an electrospinning method

Nanoscale poly(vinyl alcohol) (PVA) fiber (100–500 nm) aggregates were prepared with an electrospinning technique. Additionally, a chemical crosslinking method was used to crosslink the nanoscale PVA fiber aggregates. Differential scanning calorimetry, wide‐angle X‐ray diffraction, and scanning electron microscopy techniques were employed to characterize the PVA fiber aggregates. The different crosslinking densities of the PVA fiber aggregates were obtained through the control of the weight percentage of glyoxal to PVA. The crosslinking densities due to heat treatment and chemical crosslinking were studied. The influence of heat treatment could be neglected in contrast to chemical crosslinking when the curing temperature was 120 °C. The primary factor that affected the crosslinking density was the volume of the chemical crosslinking agent. The results showed that the properly crosslinked PVA fiber aggregates had better antiwater solubility and mechanical properties than the noncrosslinked PVA fiber aggregates. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1261–1268, 2002     

Athermal simulation of plastic deformation in amorphous solids at constant pressure

An algorithm is introduced for the molecular simulation of constant-pressure plastic deformation in amorphous solids at zero temperature. This allows to directly study the volume changes associated with plastic deformation (dilatancy) in glassy solids. In particular, the dilatancy of polymer glasses is an important aspect of their mechanical behavior. The new method is closely related to Berendsen's barostat, which is widely used for molecular dynamics simulations at constant pressure. The new algorithm is applied to plane strain compression of a binary Lennard-Jones glass. Conditions of constant volume lead to an increase of pressure with strain, and to a concommitant increase in shear stress. At constant (zero) pressure, by contrast, the shear stress remains constant up to the largest strains investigated (ε = 1), while the system density decreases linearly with strain. The linearity of this decrease suggests that each elementary shear relaxation event brings about an increase in volume which is proportional to the amount of shear. In contrast to the stress–strain behavior, the strain-induced structural relaxation, as measured by the self-part of the intermediate structure factor, was found to be the same in both cases. This suggests that the energy barriers that must be overcome for their nucleation continually grow in the case of constant-volume deformation, but remain the same if the deformation is carried out at constant pressure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2057–2065, 2004     

Influence of a mixing solvent with tetrahydrofuran and N,N‐dimethylformamide on electrospun poly(vinyl chloride) nonwoven mats

We evaluated the effects of the solvent composition with respect to the solution concentration, applied electric field, and tip‐to‐collector distance on the morphology of electrospun poly(vinyl chloride) (PVC) fibers. The solvent volume ratio was strongly correlated with the diameter of the electrospun fibers with respect to the other processing parameters. Electrospun PVC fibers dissolved in tetrahydrofuran (THF) had diameters ranging from 500 nm to 6 μm; those dissolved in N,N‐dimethylformamide (DMF) had an average diameter of 200 nm. The diameters of the electrospun fibers were obtained from narrow to broad distributions with the solvent composition. Also, the diameters of fibers electrospun from a mixed solvent of THF and DMF were less than 1 μm. The mechanical properties of electrospun PVC nonwoven mats depended on the fiber orientation and linear velocity of the drum surface. With increasing linear velocity of the drum surface, electrospun PVC fibers were arranged toward the machine direction, and the dimensions of the spiral path were shorter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2259–2268, 2002     

Effect of introduction mode of hydroxyl functionality on morphology and film properties of cycloaliphatic diepoxide crosslinkable core‐shell latex

Three series of core‐shell hydroxyl‐functionalized latexes were synthesized and then crosslinked with a cycloaliphatic diepoxide. The same amount of hydroxyl functional monomer was added during the core stage, shell stage, or partitioned equally between the core and the shell. The morphology of the latexes was examined with transmission electron microscopy and contact‐angle measurement. The stress‐strain behavior, viscoelastic properties, and water adsorption were evaluated for the latex films as a function of hydroxyl location. The location of hydroxyl groups within latex particles appeared to be dependent on the introduction mode of hydroxyl functional monomers. The introduction of hydroxyl groups during the shell polymerization resulted in a higher crosslinking density but a lower Tukon hardness and tensile properties. Not surprisingly, distribution of hydroxyl groups in both core and shell polymerization provided the lowest water adsorption and impact resistance as well as the highest tensile elongation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4256–4265, 2002     

Diffusion mobility of reactants,phase equilibrium,and specific features of radical copolymerization kinetics in the nonyl acrylate/2‐methyl‐5‐vinyltetrazole system

Combined analysis of experimental data on monomer diffusion, phase equilibrium, and copolymerization kinetics in systems of monomers (nonyl acrylate and 2‐methyl‐5‐vinyltetrazole) as well as their copolymers and homopolymers was carried out. The composition of the mixture in the vicinity of the growing macroradical can differ significantly from the average composition in the whole reactor volume because of consumption of the more‐reactive reactant 2‐methyl‐5‐vinyltetrazole. Nonyl acrylate exhibited limited compatibility with copolymers enriched in 2‐methyl‐5‐vinyltetrazole and its homopolymer. Phase diagrams were obtained for the latter homopolymer. The concentration plots of the diffusion coefficients of both monomers in their copolymers of various compositions were determined. Microphase separation was observed at specific conversions in the reaction system where the composition of a copolymer and its concentration in a monomer solution approached the binodal of the phase diagram. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1383–1389, 2002