Preparation and characterization of melt‐compounded polyethylene/vermiculite nanocomposites

Polyethylene (PE)‐layered vermiculite (VMT) nanocomposites were fabricated via direct melt compounding in a twin‐screw extruder followed by injection molding. Exfoliated PE/VMT nanocomposites were readily prepared via in situ melt mixing of maleic anhydride modified VMT with PE. Maleic anhydride acts as either the intercalation agent for VMT or as a compatibilizer for the PE and VMT phases. X‐ray diffraction and transmission electron microscopic observations revealed the formation of exfoliated PE/VMT nanocomposites. The experimental results showed that the storage modulus and strength of nanocomposites tend to increase with an increasing VMT content. Nearly 25.35% increment in the tensile strength and 50% increment in the storage modulus were achieved by incorporating 4 wt % VMT into PE. The thermal properties of the nanocomposites were investigated by dynamic mechanical analysis and differential scanning calorimetry. The glass‐transition temperature of PE/VMT nanocomposites appeared to increase upon the introduction of VMT into the PE matrix. The effects of maleic anhydride addition on the formation of the PE/VMT nanocomposites are discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1476–1484, 2003     

Structure–property relationships in polyamide 6/multi‐walled carbon nanotubes nanocomposites

Polyamide 6 (PA6)/multi‐walled carbon nanotubes (MWCNT) nanocomposites were produced by diluting a masterbach containing 20 wt % nanotubes using melt mixing. The influence of the addition of well dispersed MWCNT (as indicated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM)) on the thermal transitions, and crystallization behavior of the PA6 matrix is investigated. Differential scanning calorimetry (DSC) results show a reduction in heat capacity jump at the glass transition which is interpreted by an immobilized interfacial layer near the nanotubes. Furthermore, both DSC and X‐ray diffraction (XRD) measurements indicate that nanotubes favor the formation of the α crystalline form of PA6. These findings are correlated with the observed improvement of the storage modulus as revealed by dynamic mechanical thermal analysis (DMTA). Additionally, a new crystallization peak appears when MWCNT are added, and is attributed to the formation of a different morphology of the same type crystallite around the nanotubes walls (trans‐crystallinity). Finally, water sorption measurements show an increase of water content, normalized to the amorphous polymer fraction, in the nanocomposites. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 764–774, 2009     

Impact‐modified polypropylene/vermiculite nanocomposites

Impact‐modified polypropylene (PP)/vermiculite (VMT) nanocomposites toughened with maleated styrene–ethylene butylene–styrene (SEBS‐g‐MA) were compounded in a twin‐screw extruder and injection‐molded. VMT was treated with maleic anhydride, which acted both as a compatibilizer for the polymeric matrices and as a swelling agent for VMT in the nanocomposites. The effects of the impact modifier on the morphology and the impact, static, and dynamic mechanical properties of the PP/VMT nanocomposites were investigated. Transmission electron microscopy revealed that an exfoliated VMT silicate layer structure was formed in ternary (PP–SEBS‐g‐MA)/VMT nanocomposites. Tensile tests showed that the styrene–ethylene butylene–styrene additions improved the tensile ductility of the (PP–SEBS‐g‐MA)/VMT ternary nanocomposites at the expense of their tensile stiffness and strength. Moreover, Izod impact measurements indicated that the SEBS‐g‐MA addition led to a significant improvement in the impact strength of the nanocomposites. The SEBS‐g‐MA elastomer was found to be very effective at converting brittle PP/VMT organoclay composites into tough nanocomposites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2332–2341, 2003     

Compatibilization level effects on the structure and mechanical properties of rubber‐modified polyamide‐6/clay nanocomposites

Exfoliated polyamide‐6 (PA6)/organically modified montmorillonite clay (OMMT) nanocomposites (PNs) were modified with partially maleinized styrene–ethylene/butadiene–styrene triblock copolymers (SEBS) at three maleinization levels in an attempt to link in these materials high toughness with appropriate small‐strain and fracture tensile properties. OMMT stayed only in the PA6 matrix, and no preferential location in the matrix/rubber interphase was observed. The increased dispersed phase size upon the addition of OMMT was attributed to interactions between maleic anhydride (MA) functionalized SEBS and the surfactant of OMMT. The rubber particle size generally decreased when the MA content of SEBS increased, and this indicated compatibilization. The subsequent good adhesion led to tough nanocomposites across a wide range of both strain rates and fracture modes. As the critical interparticle distance (τ_c) decreased with the MA content, and the other parameters that could influence the surface‐to‐surface mean interparticle distance did not change, it is proposed that in these PNs higher adhesion leads to a smaller τ_c value. Finally, the presence in the matrix of a nanostructured clay makes the rubber content necessary for the toughness jump to increase and τ_c to decrease. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3611–3620, 2005     

Thermal studies on polypropylene/polyamide‐6 blends modified by succinic anhydride and succinyl fluorescein grafted polypropylenes

This study investigates the role played by two different interface agents on the basis of atactic polypropylene in the continuous/disperse phase polypropylene/polyamide‐6 (PP/PA6) system. The two agents used were obtained at the authors' laboratories from an atactic polypropylene byproduct derived from industrial polymerization reactors and consist of two grafted polymers containing either succinic anhydride (a‐PP‐SA) or both succinyl‐fluorescein and succinic anhydride grafted groups (a‐PP‐SF/SA). The role of these grafted polymers as compatibilizers in PP/PA6 polymer blends has been confirmed in previous investigations on the basis of their macroscopic behavior. This work investigates the thermal study of these blends where polypropylene acts as the polymer matrix and polyamide as the dispersed phase. Under isothermal conditions, thermal analysis agrees with the changes in the overall system behavior caused by the presence of the interface agents. These aspects were confirmed by polarized light microscopy that showed the morphology of the blends before and after modification with a‐PP‐SA or a‐PP‐SF/SA. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1307–1315, 2002     

Reinforcement of solid‐melt interfaces for semicrystalline polymers in a sequential two‐staged injection molding process

The solid‐melt interfaces between polyethylene (PE) and polyamide 6 (PA6) reinforced by in situ reactive compatibilization in a sequential two‐staged injection molding process has been studied in this work. The effects of the maleic anhydride grafted PE content and processing parameters, such as injection pressure, injection speed, melt temperature, and mold temperature, on the interfacial adhesion were investigated experimentally. The results of the interfacial adhesion characterized by lap shear measurement showed that the interfacial temperature and heat transfer between PE and PA6 interfaces play a very significant role in the bonding process. The fracture surfaces of the specimens prepared at different calculated interfacial temperature were investigated by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC), which suggested that the fracture failure changes from adhesive to cohesive failure with increasing interfacial temperature. The contribution of crystalline parts of the in situ formed copolymers to the enhancement in interfacial adhesion also was determined by DSC analysis. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1112–1124, 2009     

Effect of PPO‐g‐MA on structures and properties of PPO/PA6/short glass fiber composites

Poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6) blends were reactively compatibilized by maleic anhydride (MA) grafted PPO (PPO‐g‐MA) and reinforced by short glass fibers (SGF) via melt extrusion. An observation of the SGF‐polymer interface by scanning electronic microscope (SEM) together with etching techniques indicated that the PPO‐g‐MA played a decisive role in the adhesion of polymers to SGF. The rheological behavior was investigated by capillary rheometer, and the addition of PPO‐g‐MA, and SGF could increase the viscosity of the PPO/PA6 blends. The analysis of fiber orientation and distribution in the PPO/PA6/SGF composites showed PPO‐g‐MA favored to the random dispersion of SGF. The statistic analysis of SGF length showed that PPO‐g‐MA was helpful to maintain the fiber length during melt‐processing. For the composites at a given SGF content of 30 wt %, the addition of PPO‐g‐MA increased the tensile strength from 59.4 MPa to 97.1 MPa and increased SGF efficiency factor from 0.028 to 0.132. The experimental data were consistent with the theoretical predictions of the extension of Kelly‐Tyson model for tensile strength. The fracture toughness of the composites was investigated by single edge notch three‐point bending test. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2188–2197, 2009     

Characterization,morphology, thermal and mechanical properties of conductive polyaniline‐functionalized EPDM elastomers obtained by casting

Conductive elastomeric blends based on ethylene–propylene–5‐ethylidene–2‐norbornene terpolymer (EPDM) and polyaniline doped with 4‐dodecylbenzenesulfonic acid [PAni(DBSA)] were cast from organic solvents. Functionalization of the elastomer was promoted by grafting with maleic anhydride. Vulcanization conditions were optimized with an oscillating disk rheometer. The conductivity, morphology, thermal stability, compatibility, and mechanical behavior of the obtained mixtures were analyzed by in situ direct current conductivity measurements, atomic force microscopy, transmission electron microscopy, wide‐angle X‐ray scattering, thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical thermal analysis, stress–strain and hysteresis tests. The vulcanization process was affected by temperature, the PAni content, and maleic anhydride. A reinforcement effect was promoted by the vulcanizing agent. The formation of links between the high‐molar‐mass phases and oligomers of PAni(DBSA) in the elastomeric matrix enhanced the thermal stability and ultimate properties of the blends. By the appropriate control of the polymer blends' composition, it was possible to produce elastomeric materials with conductivities in the range of 10^?5–10^?4 S · cm^?1 and excellent mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1767–1782, 2004     

A study on melt grafting of maleic anhydride onto low‐density polyethylene and its blend with polyamide 6

Graft copolymerization of low‐density polyethylene (LDPE) with a maleic anhydride (MAH) was performed using intermeshing corotating twin‐screw extruder in the presence of benzoyl peroxide (BPO). The LDPE/polyamide 6 (PA6) and LDPE‐g‐MAH/PA6 blends were prepared in a corotating twin‐screw extruder. The melt viscosity of the grafted LDPE was measured by a capillary rheometer. The grafted copolymer was characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microcopy (SEM). The influence of the variation in temperature, BPO and MAH concentration, and temperature on the grafting degree and on the melt viscosity was studied. The grafting degree increased appreciably up to about 0.45 phr and then decreased continuously with an increasing BPO concentration. According to the FTIR analysis, it was found that the amount of grafted MAH on the LDPE chains was ～5.1%. Thermal analysis showed that melting temperature of the graft copolymers decreases with increasing grafting degree. In addition to this, loss modulus (E″) of the copolymers first increased little with increasing grafting and then obviously decreased with increasing grafting degree. Furthermore, the results revealed that the tensile strength of the blends increased linearly with increasing PA6 content. The results of SEM and mechanical test showed that the blends have good interfacial adhesion and good stability of the phase structure, which is reflected in the mechanical properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 267–275, 2010     

Preparation and nonisothermal crystallization behavior of polyamide 6/montmorillonite nanocomposites

Polyamide 6 (PA6)/montmorillonite (MMT) nanocomposites were prepared via melt intercalation. The structure, mechanical properties, and nonisothermal crystallization kinetics of PA6/MMT nanocomposites were investigated by X‐ray diffraction (XRD), tensile and impact tests, and differential scanning calorimetry (DSC). Before melt compounding, MMT was treated with an organic surfactant agent. XRD traces showed that PA6 crystallizes exclusively in γ‐crystalline structure within the nanocomposites. Tensile measurements showed that the MMT additions are beneficial in improving the strength and the stiffness of PA6, at the expense of tensile ductility. Impact tests revealed that the impact strength of PA6/MMT nanocomposites tended to decrease with increasing MMT content. The nonisothermal crystallization DSC data were analyzed by Avrami, Ozawa, modified Avrami‐Ozawa, and Nedkov methods. The validity of these empirical equations on the nonisothermal crystallization process of PA6/MMT nanocomposites is discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2878–2891, 2004     

Polyamide‐6/natural clay mineral nanocomposites prepared by solid‐state shear milling using pan‐mill equipment

The polyamide‐6 (PA6)/natural clay mineral nanocomposites were successfully prepared by solid‐state shear milling method without any treatment of clay mineral and additives. PA6/clay mixture was pan‐milled to produce PA6/clay compounding powder, using pan‐mill equipment. The obtained powder as master batch was diluted with neat PA6 to prepare composites by a twin‐screw extruder. The clay silicate layers were found to be partially exfoliated and dispersed homogeneously at nanometer level in PA6 matrix. The rheological measurements and mechanical properties of nanocomposites were characterized. The shear viscosities of nanocomposites were higher than that of pure PA6, and tensile strength and tensile modulus increased, but Izod impact strength decreased, with increasing concentration of clay. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 249–255, 2006     

Synthesis of well‐defined copolymer of acrylonitrile and maleic anhydride via RAFT polymerization

Well‐defined copolymer of acrylonitrile (AN) and maleic anhydride (MAn) has been successfully synthesized via reversible addition‐fragmentation chain transfer polymerization. The polymerization kinetics and “living”/controlled features were thoroughly studied and confirmed. The thermal properties and spinnability of the prepared copolymers were investigated via differential scanning calorimetry, thermogravimetric analyzer, and electrospinning subsequently. When PAN‐co‐PMAn was used as precursors, nonwoven with “crosslinked” structures was obtained during electrospinning. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5263–5269     

Polypropylene/layered double hydroxide nanocomposites: Synergistic effect of designed filler modification and compatibilizing agent on the morphology,thermal, and mechanical properties

This work addresses the optimization of the morphology, thermal, and mechanical properties of polypropylene/layered double hydroxide (LDH) nanocomposites. For this, the nanofillers were modified by a calcination rehydration process using two surfactants, sodium dodecylsulfate (SDS) and sodium dodecylbenzenesulfonate, respectively. The nanofillers were characterized at each step of the modification process by thermal gravimetry, X‐ray diffraction, and Infra red spectroscopy. Furthermore, the impact of anionic modifiers on the filler surface energy and on the interactions toward water was analyzed. Polypropylene (PP)/LDH nanocomposites were then prepared by a melt intercalation process and a high molar mass maleic anhydride functionalized polypropylene (PPgMA) was introduced as a compatibilizer. The dispersion of LDH in the PP matrix was characterized and the thermal and mechanical properties of the corresponding nanocomposites were determined and discussed as a function of the filler modification, of the nanocomposite morphology, and of the filler/matrix interfacial properties. The nanocomposites prepared from SDS modified LDH and PPgMA exhibited superior properties thanks to an optimized filler dispersion state and improved interfacial interactions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 782–794     

Impact fracture toughness of polyamide‐6/montmorillonite nanocomposites toughened with a maleated styrene/ethylene butylene/styrene elastomer

Polyamide‐6 (PA6)/montmorillonite (MMT) nanocomposites toughened with maleated styrene/ethylene butylene/styrene (SEBS‐g‐MA) were prepared via melt compounding. Before melt intercalation, MMT was treated with an organic surfactant agent. Tensile and impact tests revealed that the PA6/4% MMT nanocomposite fractured in a brittle mode. The effects of SEBS‐g‐MA addition on the static tensile and impact properties of PA6/4% MMT were investigated. The results showed that the SEBS‐g‐MA addition improved the tensile ductility and impact strength of the PA6/4% MMT nanocomposite at the expenses of its tensile strength and stiffness. Accordingly, elastomer toughening represents an attractive route to novel characteristics for brittle clay‐reinforced polymer nanocomposites. The essential work of fracture (EWF) approach under impact drop‐weight conditions was used to evaluate the impact fracture toughness of nanocomposites toughened with an elastomer. Impact EWF measurements indicated that the SEBS‐g‐MA addition increased the fracture toughness of the PA6/4% MMT nanocomposite. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 585–595, 2005     

Preparation and properties of isobutylene–isoprene rubber–clay nanocomposites

Isobutylene isoprene rubber (IIR)‐clay nanocomposites have been prepared successfully by melt intercalation with maleic anhydride‐grafted IIR (Ma‐g‐IIR) and organophilic clay. In IIR‐clay nanocomposites, the silicate layers of the clay were exfoliated and dispersed into the monolayer. The nanocomposites exhibited greater gas barrier properties compared with those of Ma‐g‐IIR. When 15 phr clay was added, gas barrier properties were 2.5 times greater than those of Ma‐g‐IIR. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1182–1188, 2006     

Influence of SEBS-g-MA on morphology, mechanical, and thermal properties of PA6/PP/organoclay nanocomposites

Polyamide 6/polypropylene (PA6/PP = 70/30 parts) blends containing 4 phr (parts per hundred resin) of organically modified clay (organoclay) toughened with maleated styrene-ethylene-butylene-styrene (SEBS-g-MA) were prepared by melt compounding using co-rotating twin-screw extruder followed by injection molding. X-ray diffraction (XRD) and transmission electron microscope (TEM) were used to characterize the structure of the nanocomposites. The mechanical properties of the nanocomposites were determined by tensile, flexural, and notched Izod impact tests. The single edge notch three point bending test was used to evaluate the fracture toughness of SEBS-g-MA toughened PA6/PP nanocomposites. Thermal properties were studied by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). XRD and TEM results indicated the formation of the exfoliated structure for the PA6/PP/organoclay nanocomposites with and without SEBS-g-MA. With the exception of stiffness and strength, the addition of SEBS-g-MA into the PA6/PP/organoclay nanocomposites increased ductility, impact strength and fracture toughness. The elongation at break and fracture toughness of PA6/PP blends and nanocomposites were increased with increasing the testing speed, whereas tensile strength was decreased. The increase in ductility and fracture toughness at high testing speed could be attributed to the thermal blunting mechanism in front of crack tip. DSC results revealed that the presence of SEBS-g-MA had negligible effect on the melting and crystallization behavior of the PA6/PP/organoclay nanocomposites. TGA results showed that the incorporation of SEBS-g-MA increased the thermal stability of the nanocomposite.     

The role of interfacial compatibilization upon the microstructure and electrical conductivity threshold in polypropylene/expanded graphite nanocomposites

Attempts have been made to evaluate the effect of interface and degree of interfacial interaction upon electrical conductivity threshold in polypropylene/expanded graphite (PP/EG) nanocomposites, and dispersion state of graphite nanosheets. For this purpose, maleic anhydride grafted polypropylene (PPgMA) and maleic anhydride grafted EPDM (EPDMgMA) were used as compatibilizer. Nanocomposite samples containing 1–5 vol% of EG were prepared by melt mixing method using laboratory scale internal mixer. Characterization was carried out by using X‐ray diffraction (XRD), differential scanning calorimeter (DSC), thermo‐gravimetric analysis (TGA), scanning electron microscope (SEM), transmission electron microscope (TEM), and rheo‐mechanical spectroscopy (RMS). The conductivity measurements were carried out by using four point probe method according to ASTM D991. Results showed that the conductivity threshold is controlled by the extent of interfacial interaction between PP and EG. So, better conductivity was obtained using PPgMA as compatibilizer which causes higher level of interaction between PP and EG, and therefore better dispersion of the EG nanolayers in the polymer matrix. On the other hand, high levels of compatibilizers, especially EPDMgMA, caused formation of separated aggregates of EG shelled with the compatibilizer, which results in the reduction of conductivity of the nanocomposites. This finding has been verified by SEM, RMS, and conductivity measurements. Effects of EG nanolayers on crystalline structure and thermal decomposition temperature of the nanocomposites have also been investigated by DSC and TGA, respectively. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of poly(styrene‐maleic anhydride)‐montmorillonite nanocomposite

Poly(styrene‐maleic anhydride)‐montmorillonite nanocomposites were prepared by intercalation of layered montmorillonite with the polymer ions. Synthetic approaches including polymerization and phosphonium salt formation have been used for polymer intercalation and dispersion of the host layers in the polymer matrix. The ratio of the mineral in the composites ranged 30–50%. Wide‐angle X‐ray diffraction (WAXD) disclosed that the d₍₀₀₁₎ spacing between the internal lamellar surface were only expanding to about 13 and 15 Å according to the type of phosphonium salt suggesting packing of polymer molecules between the layers. Examination of these materials by scanning and transmission electron microscopy showed spherical nano size particles of average diameter, 350 nm. Copyright © 2002 John Wiley & Sons, Ltd.     

Extruder‐made TPO nanocomposites. II. Effect of maleated poly(propylene)/organoclay ratio on morphology and thermal expansion behavior

Coefficients of linear thermal expansion (CTE) for poly(propylene)/ poly(propylene)‐grafted‐maleic anhydride/montmorillonite ethylene‐co‐octene elastomer (PP/PP‐g‐MA/MMT/EOR) blend nanocomposites were determined as a function of MMT content and various PP‐g‐MA/organoclay masterbatch ratios. The nanocomposites were prepared in a twin‐screw extruder at a fixed 30 wt % elastomer, 0–7 wt % MMT content, and various PP‐g‐MA/organoclay ratio of 0, 0.5, 1.0, and 1.5. The organoclay dispersion facilitated by the maleated PP helps to reduce the size of the dispersed phase elastomer particles in the PP matrix. The elastomer particle size decreased significantly as the PP‐g‐MA/organoclay ratio and MMT content increased; the elastomer particles viewed // to flow direction (FD) are smaller and less deformed compared to those viewed // to transverse direction (TD). The elastomer particle shape based on the view along the three orthogonal directions of the injection molded sample is similar to a prolate ellipsoid. The CTE decreased significantly in the FD and TD, whereas a slight increase is observed in the normal direction in the presence of MMT and PP‐g‐MA. The Chow model based on a two population approach showed better fit to experimental CTE when the effect of MMT and elastomer are considered individually. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B Polym. Phys. 2013 , 51, 952–965     

Influence of the type of epoxy hardener on the structure and properties of interpenetrated vinyl ester/epoxy resins

The morphology–toughness relationship of vinyl ester/cycloaliphatic epoxy hybrid resins of interpenetrating network (IPN) structures was studied as a function of the epoxy hardening. The epoxy was crosslinked via polyaddition reactions (with aliphatic and cycloaliphatic diamines), cationic homopolymerization (via a boron trifluoride complex), and maleic anhydride. Maleic anhydride worked as a dual‐phase crosslinking agent by favoring the formation of a grafted IPN structure between the vinyl ester and epoxy. The type of epoxy hardener strongly affected the IPN morphology and toughness. The toughness was assessed by linear elastic fracture mechanics, which determined the fracture toughness and energy. The more compact the IPN structure was, the lower the fracture energy was of the interpenetrated vinyl ester/epoxy formulations. This resulted in the following toughness ranking: aliphatic diamine > cycloaliphatic diamine ≥ boron trifluoride complex > maleic anhydride. For IPN characterization, the width of the entangling bands and the surface roughness parameters were considered. Their values were deduced from atomic force microscopy scans taken on ion‐etched surfaces. More compact, less rough IPN‐structured resins possessed lower toughness parameters than less compact, rougher structured ones. The latter were less compatible according to dynamic mechanical thermal and thermogravimetric analyses. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5471–5481, 2004