Heat capacity of poly(butylene terephthalate)

The low‐temperature heat capacity of poly(butylene terephthalate) (PBT) was measured from 5 to 330 K. The experimental heat capacity of solid PBT, below the glass transition, was linked to its approximate group and skeletal vibrational spectrum. The 21 skeletal vibrations were estimated with a general Tarasov equation with the parameters Θ₁ = 530 K and Θ₂ = Θ₃ = 55 K. The calculated and experimental heat capacities of solid PBT agreed within better than ±3% between 5 and 200 K. The newly calculated vibrational heat capacity of the solid from this study and the liquid heat capacity from the ATHAS Data Bank were applied as reference values for a quantitative thermal analysis of the apparent heat capacity of semicrystalline PBT between the glass and melting transitions as obtained by differential scanning calorimetry. From these results, the integral thermodynamic functions (enthalpy, entropy, and Gibbs function) of crystalline and amorphous PBT were calculated. Finally, the changes in the crystallinity with the temperature were analyzed. With the crystallinity, a baseline was constructed that separated the thermodynamic heat capacity from cold crystallization, reorganization, annealing, and melting effects contained in the apparent heat capacity. For semicrystalline PBT samples, the mobile‐amorphous and rigid‐amorphous fractions were estimated to complete the thermal analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4401–4411, 2004     

Reversible and irreversible heat capacity of poly(trimethylene terephthalate) analyzed by temperature‐modulated differential scanning calorimetry

The heat capacity of poly(trimethylene terephthalate) (PTT) has been analyzed using temperature‐modulated differential scanning calorimetry (TMDSC) and compared with results obtained earlier from adiabatic calorimetry and standard differential scanning calorimetry (DSC). Using quasi‐isothermal TMDSC, the apparent reversing and nonreversing heat capacities were determined from 220 to 540 K, including glass and melting transitions. Truly reversible and time‐dependent irreversible heat effects were separated. The extrapolated vibrational heat capacity of the solid and the total heat capacity of the liquid served as baselines for the analysis. As one approaches the melting region from lower temperature, semicrystalline PTT shows a reversing heat capacity, which is larger than that of the liquid, an observation that is common also for other polymers. This higher heat capacity is interpreted as a reversible surface or bulk melting and crystallization, which does not need to undergo molecular nucleation. Additional time‐dependent, reversing contributions, dominating at temperatures even closer to the melting peak, are linked to reorganization and recrystallization (annealing), while the major melting is fully irreversible (nonreversing contribution). © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 622–631, 2000     

Polymer crystalline structure and morphology changes in nylon‐6/ZnO nanocomposites

The influence of ZnO nanoparticles on the crystalline structures of nylon‐6 under different crystallization conditions (annealing at different temperatures from the amorphous solid, isothermal crystallization from the melt at different temperatures, and crystallization from the solution) has been examined with differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction, field emission scanning electron microscopy, and Fourier transform infrared. ZnO nanoparticles can induce the γ‐crystalline form in nylon‐6 when it is cooled from the melted state and annealed from the amorphous solid. This effect of ZnO nanoparticles increases with decreasing particle size and changes under different crystallization conditions. The effects of ZnO nanoparticles on the crystallization kinetics of nylon‐6 have also been studied with DSC. The results show that ZnO nanoparticles have two competing effects on the crystallization of nylon‐6: inducing the nucleation but retarding the mobility of polymer chains. Finally, the melting behavior of the composites has been investigated with DSC, and the multiple melting peaks of composites containing ZnO nanoparticles and pure nylon‐6 are ascribed to the reorganization of imperfect crystals. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1033–1050, 2003     

(2‐Hydroxy isobutyric) acid containing poly(glycolic acid): Structure–properties relationship

Poly(glycolic acid) (PGA) and a series of novel random copolymers of PGA containing 2‐hydroxyisobutyrric acid (PGAPHIB) (HIB unit content from 1.5 to 7.4 mol %) were synthesized and characterized in terms of chemical structure and molecular weight. Afterward, the polyesters were examined by thermogravimetric analysis, differential scanning calorimetry, and X‐ray diffraction techniques. The copolymers, which displayed a better thermal stability than PGA, at room temperature appeared as semicrystalline materials: the main effect of copolymerization was a lowering in the amount of crystallinity and a decrease of the melting temperature with respect to homopolymer PGA. Baur's equation described well the T_m‐composition data. X‐ray diffraction measurements allowed the identification of the PGA crystalline structure in all cases. After melt quenching, semicrystalline samples were obtained with the exception of PGAPHIB7.4 copolymer. The introduction of HIB units decreased the crystallization rate compared with pure PGA. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1901–1910, 2010     

Crystallization in PHB/DGEBA blends

Real‐time experiments using small‐angle X‐ray scattering and differential scanning calorimetry on blends of the semicrystalline polyester poly(3‐hydroxybutyrate) (PHB) and amorphous monomer epoxy DGEBA (diglycidyl ether of bisphenol A) were performed. Differences in the processes of melting and re‐crystallization were observed in blends relative to pure PHB. The results obtained in this study indicated that re‐crystallization is more important in blends with 50% DGEBA than in pure PHB. Moreover, segregation toward the interfibrillar region would facilitate re‐crystallization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 882–886     

Synthesis and characterization of poly(benzobisthiazole)s derived from halogenated phthalic acid and isophthalic acid

Poly(benzobisthiazole)s containing tetrafluorophenyl and bromophenyl moieties were synthesized via the polycondensation of 2,5‐diamino‐1,4‐benzenedithiol dihydrochloride with tetrafluorophthalic acid and 4‐bromoisophthalic acid under a nitrogen atmosphere. The polymers were characterized by X‐ray diffraction, spectroscopy (infrared and solid‐state ¹³C NMR), and thermal analysis, including differential scanning calorimetry and thermogravimetric analysis. The thermogravimetric analysis showed that the thermal stability of the polymers was 490–515 °C under a nitrogen atmosphere. The synthesized polymers showed good solubility in organic solvents. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3959–3966, 2002     

Poly(ethylene terephthalate) copolymers containing nitroterephthalic units. II. Crystallization and conformational studies

The effect of incorporating a nitro side group into the phenylene units of poly(ethylene terephthalate) (PET) on the conformation and crystallizability of this polyester was evaluated. Random poly(ethylene terephthalate‐co‐nitroterephthalate) (PETNT) copolymers containing 5, 10, and 15 mol % nitroterephthalic units were investigated with reference to PET. All the examined copolymers were semicrystalline and were found to adopt the triclinic crystal structure of PET, with the nitrated units being excluded from the crystallites. Both the crystallinity and crystallization rate of PETNT largely decreased with the content of nitrated units, and the O? CH₂? CH₂? O trans‐to‐gauche conformational ratio increased with crystallization, attaining comparable values for all the compositions. The conformation and crystallinity of isothermally crystallized PET and PETNT samples could be correlated with the size of the crystallites generated in each case. However, a different crystal perfecting mechanism seemed to operate for PET and for the PETNT copolymers when they were subjected to annealing. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2759–2771, 2002     

Compatibility and thermal properties of poly(3‐hydroxybutyrate)/poly(glycidyl methacrylate) blends

Poly(3‐hydroxybutyrate) (PHB)/poly(glycidyl methacrylate) (PGMA) blends were prepared by a solution‐precipitation procedure. The compatibility and thermal decomposition behavior of the PHB/PGMA blends was studied with differential scanning calorimetry, thermogravimetric analysis, and differential thermal analysis (DTA). The blends were immiscible in the as‐blended state, but for the blends with PGMA contents of 50 wt % or more, the compatibility was dramatically changed after 1 min of annealing at 200 °C. In addition, PHB/PGMA blends showed higher thermal stability, as measured by maximum decomposition temperatures and residual weight during thermal degradation. This was probably due to crosslinking reactions of the epoxide groups in the PGMA component with the carboxyl chain ends of PHB fragments during the degradation process, and the occurrence of such reactions can be assigned to the exothermic peaks in the DTA thermograms. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 351–358, 2002     

Differential scanning calorimetry,small‐angle X‐ray scattering,and wide‐angle X‐ray scattering on homogeneous and heterogeneous ethylene‐α‐copolymers

The objective of this work was to use both X‐ray and differential scanning calorimetry techniques in a comparative study of the lamellar and crystalline structures of heterogeneous and homogeneous ethylene‐α‐copolymers. The samples differed in the comonomer type (1‐butene, 1‐hexene, 1‐octene, and hexadecene), comonomer content, and catalyst used in the polymerizations. Step crystallizations were performed with differential scanning calorimetry, and the crystallinity and lamellar thicknesses of the different crystal populations were determined. Wide‐angle X‐ray scattering was used to determine crystallinities, average sizes of the crystallites, and dimensions of the orthorhombic unit cell. The average thickness, separation of the lamellae, and volume fractions of the crystalline phase were determined by small‐angle X‐ray scattering (SAXS). The results revealed that at densities below 900 kg/m³, polymers were organized as poorly organized crystal bundles. The lamellar distances were smaller and the lamellar thickness distributions were narrower for the homogeneous ethylene copolymers than for the heterogeneous ones. Step‐crystallization experiments by SAXS demonstrated that the long period increased after annealing. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1860–1875, 2001     

Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

Annealing‐induced increase of permeability and amorphous‐phase mobility in an ethylene–vinylacetate copolymer

The 50% increased permeability after annealing of semicrystalline poly(ethylene/vinylacetate) containing 3 mol % vinylacetate is linked to increased mobility in the amorphous phase, as identified by line‐narrowing of ¹H wideline nuclear magnetic resonance (NMR) spectra and by reduced cross‐polarization efficiency in ¹³C NMR. Other morphological parameters, such as crystallinity, measured as 30 to 35% by differential scanning calorimetry (DSC) and NMR, are hardly changed by annealing. Small‐angle X‐ray scattering and NMR studies, using spin diffusion as well as T_1ρ and T₁ relaxation, detected only a small increase in crystallite thickness. The annealing‐induced enhancement in segmental mobility in the amorphous regions corresponds to a temperature shift of about 10 K, from which an increase of the motional rate by a factor of 2 is estimated, and which can account for the enhancement in the permeability. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2774–2780, 2001     

Diffusion of oxygen and carbon dioxide in thermally crystallized syndiotactic polystyrene

The diffusion, solubility, and permeability behavior of oxygen and carbon dioxide were studied in amorphous and semicrystalline syndiotactic polystyrene (s‐PS). The crystallinity was induced in s‐PS by crystallization from the melt and cold crystallization. Crystalline s‐PS exhibited very different gas permeation behavior depending on the crystallization conditions. The behavior was attributed to the formation of different isomorphic crystalline forms in the solid‐state structure of this polymer. The β crystalline form was virtually impermeable for the transport of oxygen and carbon dioxide. In contrast, the α crystalline form was highly permeable for the transport of oxygen and carbon dioxide. High gas permeability of the α crystals was attributed to the loose crystalline structure of this crystalline form containing nanochannels oriented parallel to the polymer chain direction. A model describing the diffusion and permeability of gas molecules in the composite permeation medium, consisting of the amorphous matrix and the dispersed crystalline phase with nanochannels, was proposed. Cold crystallization of s‐PS led to the formation of a complex ordered phase and resulted in complex permeation behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2519–2538, 2001     

Solid‐state NMR analyses of the crystalline–noncrystalline structure and its thermal changes for ethylene ionomers

The crystalline–noncrystalline structure and its structural changes from thermal treatments for ethylene ionomers have been investigated with solid‐state ¹³C and ²³Na NMR spectroscopy. ¹³C spin–lattice relaxation time (T_1C) measurements reveal that as‐received ethylene ionomers have much enhanced molecular mobility in the crystalline region in comparison with conventional polyethylene samples. By appropriate annealing, however, polyethylene‐like morphological features reflecting T_1C behavior can also be observed. ¹³C spin–spin relaxation time (T_2C) measurements for the noncrystalline region reveal the existence of two components with different T_2C values, and these two components have been assigned to the crystalline–amorphous interfacial and rubbery–amorphous components. These results indicate that the structure of the major part of the noncrystalline region in the ethylene ionomers is similar to that of bulk‐crystallized polyethylene samples, regardless of possible ionic aggregates. The origin of the lower temperature endothermic peak in the heating process of the differential scanning calorimetry curve observed for the as‐received sample has also been examined somewhat in detail. As a result, it is proposed that the melting of smaller crystallites produced during storage at room temperature is the origin of the lower temperature peak. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1142–1153, 2002     

Crystallinity changes in plastically deformed isotactic polypropylene evaluated by x‐ray diffraction and differential scanning calorimetry methods

The crystallinity of isotactic polypropylene (iPP), when deformed with plastic plane‐strain compression, was studied with wide‐angle X‐ray scattering (WAXS) and differential scanning calorimetry (DSC) techniques. A comparison of the obtained crystallinity data with annealed iPP samples was performed. The material used in this study was commercial iPP (weight‐average molecular weight = 117.400 g/mol; number‐average molecular weight = 17.300 g/mol). A significant decrease in the crystallinity was observed with increasing deformation pressure when the X‐ray method was employed, whereas only a small decrease was registered when the DSC method of crystallinity determination was used. However, the annealed iPP samples demonstrated a slight crystallinity increase when evaluated by both techniques. The reason for the difference between WAXS and DSC crystallinity results is discussed. This study of iPP specimens subjected to large deformation led us to the conclusion that the WAXS method provides accurate crystallinity values for the deformed material, whereas the values obtained by the DSC method do not reproduce the real crystallinity of the deformed material. This is due to the inherent heating process of the method, which causes a relaxation process and a significant change in the crystallinity of the deformed material, providing values nearer to its intrinsic equilibrium state. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 896–903, 2002     

Water‐vapor permeation in semicrystalline and molten poly(octadecyl acrylate)

The water‐vapor permeability of poly(octadecyl acrylate) (PA‐18) was measured as a function of temperature in the region traversing its melting point (50 °C). The molten‐state permeability of PA‐18 is comparable to that of shorter side‐chain methacrylate polymers. Water permeability in the semicrystalline state of PA‐18 is similar to that of polyethylene at comparable crystallinity levels. The permeation switch, or change in permeability with the traversing of the melting point, for water is discussed in the context of previous results for other penetrants in this and other side‐chain crystalline polymers. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 979–984, 2001     

Melting and crystallization of poly(butylene terephthalate) by temperature‐modulated and superfast calorimetry

Quantitative temperature‐modulated differential scanning calorimetry (TMDSC) and superfast thin‐film chip calorimetry (SFCC) are applied to poly(butylene terephthalate)s (PBT) of different thermal histories. The data are compared with those of earlier measured heat capacities of semicrystalline PBT by adiabatic calorimetry and standard DSC. The solid and liquid heat capacities, which were linked to the vibrational and conformational molecular motion, serve as references for the quantitative analyses. Using TMDSC, the thermodynamic and kinetic responses are separated between glass and melting temperature. The changes in crystallinity are evaluated, along with the mobile–amorphous and rigid–amorphous fractions with glass transitions centered at 314 and 375 K. The SFCC showed a surprising bimodal change in crystallization rates with temperature, which stretches down to 300 K. The earlier reported thermal activity at about 248 K was followed by SFCC and TMDSC and could be shown to be an irreversible endotherm and is not caused by a glass transition and rigid–amorphous fraction, as assumed earlier. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1364–1377, 2006     

Two‐dimensional Fourier transform infrared spectroscopy study of biosynthesized poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐ co‐hydroxyvalerate)

Generalized two‐dimensional (2D) Fourier transform infrared correlation spectroscopy was used to investigate the effect of the comonomer compositions on the crystallization behavior of two types of biosynthesized random copolymers, poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐co‐hydroxyvalerate). The carbonyl absorption band around 1730 cm^?1 was sensitive to the degree of crystallinity. 2D correlation analysis demonstrated that the 3‐hydroxyhexanoate units preferred to remain in the amorphous phase of the semicrystalline poly(hydroxybutyrate‐co‐hydroxyhexanoate) copolymer, resulting in decreases in the degree of crystallinity and the rate of the crystallization process. The poly(hydroxybutyrate‐co‐hydroxyvalerate) copolymer maintained a high degree of crystallinity when the 3‐hydroxyvalerate fraction was increased from 0 to 25 mol % because of isodimorphism. The crystalline and amorphous absorption bands for the carbonyl bond for this copolymer, therefore, changed simultaneously. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 649–656, 2002; DOI 10.1002/polb.10126     

Thermal properties and influence of orientation on crystalline morphologies in stereoblock polypropylene and related elastomers

Atomic force microscopy (AFM), small angle X‐ray scattering (SAXS), temperature modulated differential scanning calorimetry (TMDSC), variable heating rate DSC, an independent rapid heating rate method for melting points, and cyclic mechanical testing were used to study semicrystalline thermoplastic elastomeric polypropylenes (ELPPs) and related semicrystalline polyolefins including ethylene copolymers. Low crystallinity (ca., 9 and 15%) ELPP samples were studied by AFM in the nonoriented and melt‐oriented states. AFM images taken as a function of time after quenching of a melt‐drawn and highly nucleated film resolved details of secondary crystallization involving lateral growth on the ordered row‐nucleated structures. For nonoriented films, isothermal melt crystallization at high temperatures (110 °C) led to similar features for the two ELPPs. The dominant crystalline morphology studied by AFM consisted of small (several nm in width) granular crystallites organized into immature but large spherulites spanning tens of microns. A striking cross‐hatch morphology was detected in regions of the surface in 110 °C crystallized samples, which is contrasted with melt‐drawn films where row nucleated structures dominated the morphology in the film under no external stress. AFM was also used to monitor the morphological changes that occurred as the films were stretched at 25 °C. Break‐down of lamellae was observed, resulting in oriented narrow fibrils. Cyclic stress‐strain curves showed the expected result where lower crystallinity ELPPs had higher recoverable levels of set after both 100 and 500% elongation. TMDSC was used to resolve the broad melting and recrystallization regions in these low to medium crystallinity ELPP systems, and to contrast the results with ethylene copolymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Copolymerization: A new tool to selectively induce poly(butylene naphthalate) crystal form

Poly(butylene/diethylene naphthalate) copolymers (PBN‐PDEN) were synthesized in bulk according to the polycondensation procedure and examined by NMR, GPC, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and XRD. At room temperature they appeared as semicrystalline materials; the copolymerization caused a lowering in the T_g value, a decrement of T_m and of the crystallization rate. Pure α or β′ form was obtained at low and high DEN unit content, respectively; crystalline form transition never occurred in the solid state, analogously to PBN. After cooling from the melt, the pure α form was always evidenced in PBN‐PDEN10 and PBN‐PDEN20, whereas the pure β′ crystal phase develops in the copolymer containing 40 mol % DEN units, independently on the cooling rate. In the case of PBN‐PDEN30 a pure α or β′ form was obtained at low and high cooling rate, respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1356–1367, 2009     

Topochemical polymerisation of assembled diacetylene macrocycle bearing dibenzylphosphine oxide in solid state

Novel diacetylene macrocycles 1 and 2 bearing dibenzylphosphine oxide were synthesised via Eglinton acetylenic intramolecular coupling. The X-ray analysis of crystals of macrocycles 1 and 2 demonstrated that the better-aligned tubular supramolecular structure was formed in macrocycle 1 than in macrocycle 2, which provided the possibility of diacetylene topochemical polymerisation in solid state of macrocycle 1. UV–vis, Raman spectroscopy and X-ray analysis indicated that the crystals of macrocycle 1 could undergo topochemical diacetylene polymerisation only on their surface by light irradiation; differential scanning calorimetry, solid-state ¹³C NMR spectroscopy and solubility test demonstrated that the crystals of macrocycle 1 could undergo diacetylene topochemical polymerisation inside solid by heat. As expected, based on the topological analysis of crystal structure, the crystals of macrocycle 2 could not undergo diacetylene topochemical polymerisation either by light irradiation or heat.