The miscibility of poly(vinyl alcohol)/poly(N-vinylpyrrolidone) blends investigated in dilute solutions and solids

Poly(vinyl alcohol) (PVA) (polymer A) and poly(N-vinylpyrrolidone) (PVP) (polymer B) are known to form a thermodynamically miscible pair. In the present study the conclusion on miscibility of PVA/PVP solid blends, confirmed qualitatively (DMTA, FTIR) and quantitatively (DSC, χ_AB = − 0.69 at 503 K) is compared with the miscibility investigations of PVA/PVP solution blends by the technique of dilute solution viscometry. The miscibility of the ternary (polymer A/ polymer B/ solvent) system is estimated on the basis of experimental and ideal values of the viscosity parameters k, b and [η]. It is found that the conclusions on miscibility or nonmiscibility drawn from viscosity measurements in dilute solution blends depend: (i) on the applied extrapolation method used for the determination of the viscosity interaction parameters, (ii) on the assumed definition of the ideal values and (iii) on the thermodynamic quality of the solvent, which in the case of PVA depends on its degree of hydrolysis. Hence, viscometric investigations of dilute PVA/PVP solution blends have revealed that viscometry, widely used in the literature for estimation of polymer-polymer miscibility can not be recommended as a sole method to presume the miscibility of a polymer pair.     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

Thermal and photochemical stability of poly(vinyl alcohol)/modified lignin blends

A kraft lignin derivative (KLD) obtained by reaction with p-aminobenzoic acid/phthalic anhydride was blended with poly(vinyl alcohol) (PVA) by solution casting from DMSO. PVA and PVA/KLD films were exposed to ultraviolet radiation (24, 48, and 96 h) and analyzed by thermogravimetry (TG), differential scanning calorimetry (DSC), infrared spectroscopy (FTIR), hydrogen nuclear magnetic resonance (¹H NMR) spectroscopy, and scanning electron microscopy (SEM). PVA films show a loss of thermal stability due to irradiation. PVA/KLD reveals greater thermal stability than PVA and an increase in thermal stability after irradiation. These results suggest that the incorporation of KLD into PVA provides a gain in thermal and photochemical stability. FTIR, ¹H NMR, DSC, and TG results obtained for the blends suggest that intermolecular interactions between PVA and KLD chains are present. SEM micrographs revealed blend miscibility for a KLD blend content of up to 15 wt%, as observed at magnification of 1000 times.     

Synthesis and Characterization of Polyaniline/Partially Phosphorylated Poly（vinyl alcohol） Nanoparticles

The polyaniline/partially phosphorylated poly（vinyl alcohol）（PANI/P-PVA） nanoparticles were prepared by the chemical oxidative dispersion polymerization of aniline monomer in 0.5 mol/L HC1 aqueous media with the partially phosphorylated poly（vinyl alcohol） （P-PVA） as the stabilizer and co-dopant. The PANI/P-PVA nanoparticles were characterized by transmission electron microscopy （TEM）, Fourier transform infrared spectroscopy （FTIR）, thermal gravimetric analysis （TGA）, X-ray diffraction （XRD）, electrical conductivity measurements and re-dispersion stability testing. All the results were compared with the properties of the conventional polyaniline in the emeraldine salt form （PANI ES）. It was found that the feeding ratio of P-PVA obviously affected the morphology, re-dispersion stability and electrical conductivity of the PANI/P-PVA nanoparticles. When the feeding ratio of P-PVA ranged from 40 wt% to 50 wt%, the PANI/P-PVA nanoparticles showed spherical shape with good uniformity, significant re-dispersion stability in aqueous media and good electrical conductivity.     

Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998     

Thermal properties of poly(vinyl chloride)/polyurethane blends

Blends of poly(vinyl chloride) and a polyurethane elastomer were investigated by DSC and tensile testing. Up to 30 wt% single glass transition was found. It was concluded that the polyurethane forms partly a true blend and is partly disperged in the continuous blend phase.     

Electrospinning and characterization of medium-molecular-weight poly(vinyl alcohol)/high-molecular-weight poly(vinyl alcohol)/montmorillonite nanofibers

Submicron fibers of medium-molecular-weight poly(vinyl alcohol) (MMW-PVA), high-molecular-weight poly(vinyl alcohol) (HMW-PVA), and montmorillonite clay (MMT) in aqueous solutions were prepared by electrospinning technique. The effect of HMW-PVA and MMT on the morphology and mechanical properties of the MMW-PVA/HMW-PVA/MMT nanofibers were investigated for the first time. Scanning electron microscopy, viscometer, tensile strength testing machine, thermal gravimetric analyzer (TGA), and transmission electron microscopy (TEM) were utilized to characterize the PVA/MMT nanofibers morphology and properties. The MMW-PVA/HMW-PVA ratios and MMT concentration played important roles in nanofiber's properties. TEM data demonstrated that exfoliated MMT layers were well distributed within nanofibers. It was also found that the mechanical property and thermal stability were increased with HMW-PVA and MMT contents.     

聚乙烯醇／壳聚糖共混膜优先透醇性能的研究

聚乙烯醇／壳聚糖共混膜优先透醇性能的研究王新平，沈之荃，张富尧，林荣轩（浙江大学高分子系，化学系，杭州，３１００２７）关键词渗透蒸发，聚乙烯醇／壳聚糖共混物膜，乙醇水溶液本文首次报道利用亲水性的聚乙烯醇和壳聚糖制得具有很高的乙醇优先透过选择性的透醇型...     

Solid‐state 13C and 129Xe NMR study of poly(vinyl alcohol) and poly(vinyl alcohol)/lactosilated chitosan gels

Dry and hydrated poly(vinyl alcohol) (PVA) gels with 55% (a‐PVA) and 61% (s‐PVA) syndiotacticity and related PVA/lactyl chitosan (LC) blends have been investigated with ¹²⁹Xe and cross‐polarization/magic‐angle‐spinning ¹³C NMR techniques. Although the dry gels exhibit two broad ¹²⁹Xe resonances in the slow‐to‐intermediate exchange limit, both hydrated gels show three resonances. The corresponding dry blends exhibit two signals, the chemical shifts and line widths of which change with respect to those of pure PVA, whereas one (a‐PVA/LC) or two (s‐PVA/LC) signals appear in the spectra of the hydrated blends. A comparative analysis of the data demonstrates that LC rearranges the domains of the polymeric matrix in both the dry and hydrated blends according to the syndiotacticity of the PVA chains. Information on the molecular motions of the amorphous and swollen polymeric domains in the kilohertz range has been obtained from an analysis of the spin‐lattice relaxation times. These data indicate that the dynamics and arrangement of the PVA chains in the gels are strongly affected by their tacticity and the addition of the copolymer LC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3123–3131, 2003     

Preparation and Properties of Poly（vinyl alcohol）/Chitosan Blend Bio-nanocomposites Reinforced by Cellulose Nanocrystals

The aim of this paper is to report the effect of the addition of cellulose nanocrystals（CNCs） on the mechanical, thermal and barrier properties of poly（vinyl alcohol）/chitosan（PVA/Cs） bio-nanocomposites films prepared through the solvent casting process. The characterizations of PVA/Cs/CNCs films were carried out in terms of X-ray diffraction（XRD）, transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, thermogravimetric analysis（TGA and DTG）, oxygen transmission rate（OTR）, and tensile tests. TEM and SEM results showed that at low loading levels, CNCs were dispersed homogenously in the PVA/Cs matrix. The tensile strength and modulus in films increased from 55.1 MPa to 98.4 MPa and from 395 MPa to 690 MPa respectively, when CNCs content went from 0 wt% to 1.0 wt%. The thermal stability and oxygen barrier properties of PVA/Cs matrix were best enhanced at 1.0 wt% of CNCs loading. The enhanced properties attained by incorporating CNCs can be beneficial in various applications.     

Fully-biodegradable poly(3-hydroxybutyrate)/poly(vinyl alcohol) blend films with compositional gradient

Fully-biodegradable bacterial poly(3-hydroxybutyrate) (PHB)/chemosynthetic poly(vinyl alcohol) (PVA) blend films with compositional gradient from one surface to the other surface of the films were prepared by a dissolution-diffusion technique. Three kinds of PVA samples, high- and low-molecular weight atactic PVA and highly syndiotactic PVA (s-PVA), were used in order to investigate the effects of molecular weight and tactic structure on the generation of compositional gradient. The solution of PHB in 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP), which is also a good solvent for PVA, was cast on the PVA film and then the solvent HFIP was evaporated. By selecting the optimum volume of solvent and the evaporation rate, the PHB/PVA blend film with compositional gradient was obtained. The formation of compositional gradient was confirmed by FT-IR microscopy and ATR-FT-IR analysis. The 50%/50% PHB/s-PVA blend film with a nearly ideal compositional gradient, that is, the composition of PHB (or PVA) in the film changing gradually from 100% at one surface to 0% at the other surface of the film was obtained by casting PHB/HFIP solution on to the s-PVA film. Positional dependence of the absorbance of C==O and OH stretching bands along the film thickness direction for the PHB/S-PVA cast films.     

Thermal degradation of copolymers from vinyl acetate and vinyl alcohol

The thermal degradation of poly(vinyl acetate) (PVA), poly(vinyl alcohol) (PVAL), vinyl acetate-vinyl alcohol (VAVAL), vinyl acetate-vinyl-3,5-dinitrobenzoate (VAVDNB) and vinyl alcohol-3,5-dinitrobenzoate (VALVDNB) copolymers have been studied using differential thermal analysis (DTA) and thermogravimetry (TG) under isothermal and dynamic conditions in nitrogen. Thermal analysis indicates that PVA and PVAL are thermally more stable than VAVAL copolymers, being PVAL the most stable polymer. The presence of small amounts of vinyl-3,5-dinitrobenzoate (VDNB) in PVA or PVAL produces a marked decrease in the thermal stability of both homopolymers, being VALVDNB copolymers the less stable materials. The apparent activation energy of the degradative process was determined by the Kissinger and Flynn-Wall methods which agree well.     

Grafting reactions of vinyl acetate onto poly[(vinyl alcohol)-co-(vinyl acetate)]

The grafting preference of vinyl acetate onto the methine carbon of poly(vinyl alcohol) (PVOH) versus the acetate group of poly(vinyl acetate) (PVAc) was determined as part of an attempt to prepare novel branched PVOH from partially hydrolyzed PVAc. The results showed long chain grafting on the acetate groups of the PVAc units rather than the methine carbons of the PVOH or PVAc units. Decreasing the monomer or initiator concentration decreased the molecular weight of the graft copolymer formed. Of the initiators studied, ammonium persulfate gave the largest increase in copolymer molecular weight. Both hydrolysis and reacetylation combined with gel permeation chromatography (GPC) and ¹³C-NMR of the fully hydrolyzed material were used to estimate the number and location of grafts. © 1996 John Wiley & Sons, Inc.     

Viscoelastic behaviors and molecular motions of highly syndiotactic poly(vinyl alcohol) fibers

The viscoelastic behavior and molecular motion of highly syndiotactic poly(vinyl alcohol) (S‐PVA) fibers with a dyad syndiotacticity (r) of 69% were studied by dynamic mechanical thermal analysis and wide‐angle X‐ray diffraction and compared with those of atactic poly(vinyl alcohol) (A‐PVA) fibers with r = 54%. The β_c dispersion, based on the molecular motion of the chain molecules in the crystalline regions, was observed for A‐PVA around 120–140 °C, and the only primary (α_c) dispersion was observed for S‐PVA around 180 °C. The thermal expansion coefficients for the a and c axes of the A‐PVA crystal changed discontinuously around 120 °C, which corresponded to the β_c dispersion. For S‐PVA, the coefficient for the (002) plane changed discontinuously around 100 °C, similarly to A‐PVA, but that for the (100) plane remained unchanged between 20 and 220 °C. These results showed that the intermolecular hydrogen bonding of S‐PVA was stronger in the direction of the a axis than in the other directions, suppressing the β_c dispersion. The storage modulus and thermal expansion coefficient of the (020) plane (molecular axis) of S‐PVA decreased markedly around 180 °C, and this indicated that the α_c dispersion was due to the torsional motion of the molecular chains in the crystalline regions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 800–808, 2004     

Structure and thermal behaviors of poly(vinyl alcohol)/surfactant composites: Investigation of molecular interaction and mechanism

Poly(vinyl alcohol) (PVA) is a promising biocompatible polymer, whose applicability is limited by its narrow processing window. Here, we adopted a facile approach to broaden the processing windows of PVA based on phosphoric ester of poly(ethylene oxide) (10) nonylphenyl (NP‐10P). Thermal analysis shows that both the melting temperature (T_m) and the glass transition temperature (T_g) of PVA decrease noticeably as NP‐10P content increases, indicating good miscibility of NP‐10P with PVA. The thermal degradation kinetics suggests composites display excellent thermal stability compared with neat PVA. The pyrolysis mechanism of PVA before and after modification with NP‐10P varies from chain unzipping degradation followed by chain random scission to chain random scission. The processing window of PVA is broadened from 9°C to 98°C with low content NP‐10P (5 wt%). Moreover, the composites maintain significant mechanical performance and transparency. This work provides an environmentally friendly and economical method to improve the possibility of thermal melt processing for PVA.     

Structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SA) blend films

The structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SF) blend films were analyzed by differential scanning calorimetry (DSC), thermomechanical (TMA) and thermogravimetric (TGA) analysis, x-ray diffractometry, and scanning (SEM) and transmission (TEM) electron microscopy. DSC curves of PVA/SF blend films showed a major endothermic peak at 220°C, along with a peak at 280°C. These endotherms were assigned to the thermal decomposition of the ordered PVA elements and to the thermal degradation of silk fibroin, respectively. The PVA/SF blends behaved in a manner intermediate to the pure components, as suggested by both contraction expansion and sample weight retention properties recorded by TMA and TGA measurements. The IR absorption spectra of the blends were identified as purely a composite of the absorption bands characteristic of both PVA and SF pure polymers. The X-ray diffraction patterns of PVA/SF blends showed overlapping spacing due to PVA and SF. A dispersed phase formed by spherical particles of 3–7 μm diameter was observed by SEM and TEM. All these findings suggest that PVA and SF are incompatible. © 1994 John Wiley & Sons, Inc.     

Alignment effect of attapulgite on the mechanical properties of poly(vinyl alcohol)/attapulgite nanocomposite fibers

Poly(vinyl alcohol) (PVA)/attapulgite (AT) nanocomposite fibers have been prepared by wet spinning. The morphology and mechanical properties of the modified PVA fibers have been characterized with transmission electron microscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), birefringence measurements, and mechanical testing. The PVA/AT nanocomposite fibers show much higher tensile strength, initial modulus, and work to break than pure PVA fibers with the same draw ratio. SEM observations demonstrate that the AT nanorods can align orderly along the fiber axis by stretching and have good adhesion to the fiber matrix. The results of birefringence measurements prove that the modified fibers have higher orientation than pure PVA fibers after stretching. The results of DSC analysis indicate that the crystallinity of the PVA fibers can be increased by the addition of AT. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1995–2000, 2006     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.     

氧化石墨烯对聚乙烯醇/硼酸水凝胶流变性能的影响

研究了氧化石墨烯(GO)对聚乙烯醇(PVA)/硼酸(borate)水凝胶线性及非线性流变性能的影响。 通过扫描电子显微镜、硼谱核磁共振波谱以及流变研究了水凝胶的流变性能。 结果表明,GO质量浓度在稀溶液区时,GO片层与PVA链间通过硼酸根离子形成了具有弹性活性的缔合点,有效地提高了水凝胶的平台模量、松弛时间和零切粘度;当GO进一步增加到亚浓溶液区,部分的交联剂被GO的团聚体捕获并处于非弹性活性的缔合状态,处于有效缔合状态的交联剂变少,导致平台模量、松弛时间和零切粘度降低。 稳态剪切测试下,样品在剪切增稠区的粘度增加随着GO添加量的增加明显加强,这与剪切场下取向的氧化石墨烯片层参与网络结构的重排有关。     

Study of the Drying Behavior of Poly(vinyl alcohol) Aqueous Solution

This paper deals with the drying behavior of poly(vinyl alcohol) aqueous solution containing an active substance and placed into a Petri box. The objective is to reduce the drying time while respecting some constraints. To succeed, it is important to understand complex mechanisms governing heat and mass transfers. During the drying, the product thickness shrinks and its properties evolve. Drying kinetics in convective and infrared radiation are presented.