Electrospun fiber mats of poly(3‐hydroxybutyrate), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate), and their blends

Electrospinning of poly(3‐hydroxybutyrate) (PHB), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV), and their blends was first carried out in chloroform at 50 °C on a stationary collector. The average diameter of the as‐spun fiber from PHB and PHBV solutions decreased with increasing collection distance and increased with increasing solution concentration and applied electrical potential. In all of the spinning conditions investigated, the average diameter of the as‐spun pure fibers ranged between 1.6 and 8.8 μm. Electrospinning of PHB, PHBV, and their blends was carried out further at a fixed solution concentration of 14% w/v on a homemade rotating cylindrical collector. Well‐aligned, cross‐sectionally round fibers without beads were obtained. The average diameter of the as‐spun pure and blend fibers ranged between 2.3 and 4.0 μm. The as‐spun fiber mats appeared to be more hydrophobic than the corresponding films and much improvement in the tensile strength and the elongation at break was observed for the blend fiber mats over those of the pure fiber ones. Lastly, indirect cytotoxicity evaluation of the as‐spun pure and blend fiber mats with mouse fibroblasts (L929) indicated that these mats posed no threat to the cells. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2923–2933, 2006     

Studies on Binary Blends of Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) and Natural Polyphenol Catechin: Specific Interactions and Thermal Properties

The existence of a specific intermolecular hydrogen‐bonding interaction between poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(3HB‐co‐3HH)] and (+)‐catechin in their blends was demonstrated by Fourier‐transform infrared spectroscopy (FT‐IR). It was found that the experimentally estimated fraction of hydrogen‐bonded carbonyl groups was much lower than the theoretically predicted maximum fraction. Only one glass transition temperature (T_g) occurred in the blends with the compositions detected by differential scanning calorimetry (DSC), being further confirmed by the results of dynamic mechanical thermal analysis (DMTA). The decrease of the melting point (T_m) and the increase of the glass transition temperature of the blends observed by the DSC measurements also suggested the existence of a strong intermolecular interaction. It was interesting to note that, as a low‐molecular‐weight compound, catechin showed a glass transition, which arises from strong self‐association. As expected, the crystalline structure of P(3HB‐co‐3HH) in the blends showed no change, but the crystallinity of the copolymer component in the blends, calculated by wide‐angle X‐ray diffraction, decreased with the increase of catechin weight content. Investigated by tensile experiments, the maximum strength and modulus decreased sharply with the increase of catechin content; on the contrary, the elongation changed slowly.

The FT‐IR spectra in the wave‐number 1 680–1 780 cm^?1 region for blends of P(3HB‐co‐3HH)/catechin. A: HBH; B: HBHC10; C: HBHC20; D: HBHC30; E: HBHC40; F: HBHC50; and G: catechin.     

Influence of multiple processing on selected properties of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)

The effect of multiple (up to 10 times) injection molding of processed poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P(3,4HB)) on its phase transition temperatures, degree of crystallinity, degradation temperature, mass flow rate, mechanical properties, dynamic mechanical properties, and Charpy's impact strength is presented. The studies have shown that the multiple injection lowers the degree of crystallinity and the thermal stability of P(3,4HB). The mass flow rate values increased with increasing the injection number. It was found that the multiple injections had no substantial effect on the tensile strength up to 10 injection cycles and the tensile strength at break, tensile strain at tensile strength, and tensile strain at break up to 6 injection cycles. The maximum value of storage modulus at 30 °C and impact strength were recorded for sample after 4 cycles of injection, while the values of storage modulus at 120 °C increased with increase of the injection cycles. Copyright © 2015 John Wiley & Sons, Ltd.     

Antibacterial poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) fibrous membranes containing quaternary ammonium salts

In this study, antimicrobial membranes based on biodegradable material poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐4HB)] and quaternary ammonium salts (QASs) by two methods have been performed. Three QASs with varied alkyl chain lengths have been synthesized successfully and characterized by ¹H nuclear magnetic resonance and Fourier transform infrared. The synthesized QASs were blended with P(3HB‐4HB) and electrospun into composite fibrous membranes or casted into conventional membranes. Electrospun fibrous membranes with large surface areas are a superior type of antimicrobial biomaterials, and they exhibit preferable properties than solution casting membranes. Specifically, electrospun fibrous membranes are tougher and can inactivate both Gram‐positive Staphylococcus aureus and Gram‐negative Escherichia coli O157:H7 in a contact time of 30 min, whereas the solution casting membranes cannot. The length of alkyl chain in the quaternary ammonium groups on the modified P(3HB‐4HB) membranes is able to influence the antimicrobial activity. This type of antimicrobial material may have potential applications in biomaterial field. Copyright © 2016 John Wiley & Sons, Ltd.     

Attenuated total reflectance/fourier transform infrared studies on the phase‐separation process of aqueous solutions of poly(n‐isopropylacrylamide)

Temperature‐induced phase separation of poly(N‐isopropylacrylamide) in aqueous solutions was studied by attenuated total reflectance (ATR)/Fourier transform infrared spectroscopy. The main objectives of the study were to understand, on a molecular level, the role of hydrogen bonding and hydrophobic effects below and above the phase‐separation temperature and to derive the scenario leading to this process. Understanding the behavior of this particular system could be quite relevant to many biological phenomena, such as protein denaturation. The temperature‐induced phase transition was easily detected by the ATR method. A sharp increase in the peaks of both hydrophobic and hydrophilic groups of the polymer and a decrease in the water‐related signals could be explained in terms of the formation of a polymer‐enriched film near the ATR crystal. Deconvolution of the amide I and amide II peaks and the O? H stretch envelope of water revealed that the phase‐separation scenario could be divided, below the phase‐separation temperature, into two steps. The first step consisted of the breaking of intermolecular hydrogen bonds between the amide groups of the polymer and the solvent and the formation of free amide groups, and the second step consisted of an increase in intramolecular hydrogen bonding, which induced a coil–globule transition. No changes in the hydrophobic signals below the separation temperature could be observed, suggesting that hydrophobic interactions played a dominant role during the aggregation of the collapsed chains but not before. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1665–1677, 2001     

Nonisothermal crystallization kinetics of poly(ε‐caprolactone) blocks in double crystalline triblock copolymers containing poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) and poly(ε‐caprolactone) units

The poly(3‐hydroxbutyrate‐co‐3‐hydroxyvalerate)/poly(ε‐caprolactone) block copolymers (PHCLs) with three different weight ratios of PCL blocks (38%, named PHCL‐38; 53%, named PHCL‐53; and 60%, named PHCL‐60) were synthesized by using PHBV with two hydroxyl end groups to initiate ring‐opening polymerization of ε‐caprolactone. During DSC cooling process, melt crystallization of PHCL‐53 at relatively high cooling rates (9, 12, and 15 °C min^?1) and PHCL‐60 at all the selected cooling rates corresponded to PCL blocks so that PHCL‐53 and PHCL‐60 were used to study the nonisothermal crystallization behaviors of PCL blocks. The kinetics of PCL blocks in PHCL‐53 and PHCL‐60 under nonisothermal crystallization conditions were analyzed by Mo equation. Mo equation was successful in describing the nonisothermal crystallization kinetics of PCL blocks in PHCLs. Crystallization activation energy were estimated using Kissinger's method. The results of kinetic parameters showed that both blocks crystallized more difficultly than corresponding homopolymers. With the increase of PCL content, the crystallization rate of PCL block increased gradually. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Morphology of poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) segmented copolyesters

Segmented copolyesters, namely, poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) (PBT‐PETIS), were synthesized with the melting transesterification processing in vacuo condition involving bulk polyester produced on a large scale (PBT) and ternary amorphous random copolyester (PETIS). Investigations on the morphology of segmented copolyesters were undertaken. The two‐phase morphology model was confirmed by transmission electron microscopy and dynamic mechanical thermal analysis. One of the phases was composed of crystallizable PBT, and the other was a homogeneous mixture of PETIS and noncrystallizable PBT. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2257–2263, 2003     

Blends of poly(3‐hydroxybutyrate)/4,4′‐thiodiphenol and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ 4,4′‐thiodiphenol: Specific interaction and properties

The specific interaction between poly(3‐hydroxybutyrate) [P(3HB)] and 4,4′‐thiodiphenol (TDP) and between poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) and TDP was investigated by Fourier transform infrared (FTIR) spectroscopy. Interassociated hydrogen bonds were found between the polyester chains and the TDP molecules in the binary blends. The fractions of associated carbonyl groups, F_b 's, in the blends first increased and then decreased as the TDP content increased. The thermal and dynamic mechanical properties of P(3HB)–TDP and PHBV–TDP blends were investigated by differential scanning calorimetry and dynamic mechanical thermal analysis, respectively. Thermal analysis revealed that the P(3HB)–TDP blends possessed eutectic phase behavior. Furthermore, it was found that the thermal and dynamic mechanical properties of P(3HB) and PHBV were greatly modified through blending with TDP. Environmental degradability in river water was evaluated by a biochemical oxygen demand tester, and it was clarified that TDP lowered the degradation rate of P(3HB). The results suggest that TDP is effective in modifying the physical properties as well as the biodegradability of polyesters. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2891–2900, 2000     

Fourier transform infrared study of poly (2-hydroxyethyl methacrylate) PHEMA

 Fourier transform infrared spectra in the wave number range 450–4500 cm^-1 of poly (2-hydroxy-ethyl methacrylate) PHEMA have been studied as functions of water content in the range 38–2.6 wt% and of temperature in the range 300–373 K. The results show changes in the intensities of the stretching frequencies of the carbonyl band, H–O–H bending vibration and O–H stretching vibration with a change in water content and temperature. The results confirm two types of water in the hydrogel polymer system, tightly bound water and loosely bound water. At low concentrations, water is mainly hydrogen-bonded to the polymer and is described as tightly bound water. However, at water concentrations greater than 18% by weight, part of the water exists in a different form and behaves as loosely bound water. For concentrations over 30%, there is some evidence that excess water behaves more loosely bound somewhat like bulk water. Infrared spectroscopic results supplement those obtained by means of NMR by Smyth et al. and by dielectric spectroscopy. Our results also show that some of the water continues to be hydrogen bonded to the polymer until at least a temperature of 373 K when the bulk water should have evaporated. FTIR is found to yield greater site-specific insight into the local behaviour of water in hydrated PHEMA. Received: 22 August 1996 Accepted: 11 November 1996     

Phase Behavior and Thermal Properties for Binary Blends of Bacterial Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s with Narrow‐Comonomer‐Unit Compositional Distribution

The miscibility and the effect of compositional distribution on physical properties were investigated for binary blends of biosynthesized poly(3‐hydroxybutyrate) [P(3HB)] and comonomer compositionally fractionated poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s [P(3HB‐co‐3HH)] with narrow compositional distribution. Biosynthesized P(3HB‐co‐3HH) samples were compositionally fractionated using solvent (chloroform)/nonsolvent (n‐heptane) mixtures. The binary blends of fractionated P(3HB‐co‐3HH)s with different 3HH unit content were prepared by casting from solution in chloroform. The miscibility and the thermal properties of these blends were analyzed by differential scanning calorimetry (DSC). It was found that the two components are miscible in the amorphous phase when the difference in 3HH unit content between the two component polymers of these blends is less than 20 mol‐%, subsequently they are immiscible when the difference is larger than 30 mol‐%. By comparing the thermal properties of the binary blends of fractions, with those for the fractions themselves, and with those for the bacterially as‐produced unfractionated copolyesters, the effects of compositional distribution on the properties of copolyesters were discussed.

Glass transition temperatures of blends PHB/H10, H10/H20, and PHB/H20 versus total 3HH unit content in the blends. The solid lines are the best fits of the experimental results of the P(3HB‐co‐3HH) fractions with narrow compositional distribution.     

Two‐dimensional Fourier transform infrared correlation spectroscopy and evolving factor analysis in the study of cationic curing of DGEBA and γ‐valerolactone mixtures

Generalized two‐dimensional (2D) correlation spectroscopy and evolving factor analysis (EFA) have been applied to the study of cationic curing reaction of mixtures of diglycidyl ether of bisphenol A (DGEBA) and γ‐valerolactone (γ‐VL). The reaction has been monitored by Fourier transform infrared spectroscopy. The reaction periods in which a chemical change takes place are identified using EFA and then the sequence of changes are established by means of the interpretation of the synchronous and asynchronous spectra obtained with 2D correlation spectroscopy. By combining this information, in the curing process, four reactions have been detected: (1) DGEBA and γ‐VL reaction to obtain a spiroorthoester intermediate, (2) homopolymerization of DGEBA, (3) copolymerization of DGEBA with the spiroorthoester intermediate, and (4) homopolymerization of the spiroorthoester. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3886–3899, 2008     

A thermodynamic analysis of specific interactions in homoblends of poly(styrene‐co‐4‐vinylpyridine) and poly(styrene‐co‐methacrylic acid)

Miscibility and strong specific interactions that occurred within homoblends of poly(styrene‐co‐4‐vinylpyridine) containing 15 mol % of 4‐vinylpyridine (PS4VP15) and poly(styrene‐co‐methacrylic acid) containing 15 mol % of methacrylic acid (PSMA15) have been examined by Fourier Transform infrared spectroscopy and DSC. The observed positive deviation of the glass transition temperature of the blends from the linear average line, was analyzed by the frequently used theoretical conventional approaches including the one very recently proposed by Brostow. A better fit was obtained when this latter is used. A reasonable agreement with experimental values was also obtained when the theoretical fitting parameter free method developed by Coleman, is applied to predict the composition dependence of the T_g of this system. A thermodynamic analysis of hydrogen bonding in this system was carried using the Painter‐Coleman association model and the variation of the Gibbs function of mixing and its different contributions and corresponding phase diagrams as a function of temperature and composition were estimated. This analysis predicted PSMA15 to be miscible with PS4VP15 in the whole composition range up to 150 °C. Above this temperature, a partial miscibility is predicted when the PS4VP15 is in excess. The DSC results are in agreement with these predictions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 923–931, 2009     

Miscibility,specific interactions,and self‐assembly behavior of phenolic/polyhedral oligomeric silsesquioxane hybrids

The miscibility of a phenolic resin with polyhedral oligomeric silsesquioxane (POSS) hybrids and the specific interactions between them were investigated with Fourier transform infrared (FTIR) spectroscopy and wide‐angle X‐ray diffraction (WAXD). An analysis of the morphology and microstructure was performed with polarized optical microscopy and atomic force microscopy (AFM). The interassociation equilibrium constant between the phenolic resin and POSS (38.7) was lower than the self‐association equilibrium constant of pure phenolic (52.3) according to the Painter–Coleman association model. This result indicated that POSS was partially miscible with the phenolic resin. A polarized optical microscopy image of a phenolic/POSS hybrid material (20 wt % POSS) indicated that the crystals of POSS were arranged evenly in the phenolic matrix; the self‐assembled array of POSS crystals was also confirmed by AFM. This phenomenon was consistent with the FTIR spectroscopy and WAXD analyses. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1127–1136, 2004     

Synthesis and non‐isothermal crystallization kinetics of poly(ethylene terephthalate)‐co‐poly(propylene glycol) copolymers

Poly(ethylene terephthalate)‐co‐poly(propylene glycol) (PET‐co‐PPG) copolymers with PPG ratio ranging from 0 to 0.90 mol% were synthesized by the melt copolycondensation. The intrinsic viscosity, structure, non‐isothermal crystallization behavior, nucleation and spherulitic growth of the copolymers were investigated by Ubbelohde viscometer, Proton Nuclear Magnetic Resonance (¹H‐NMR), differential scanning calorimetry, and polarized optical microscopy, respectively. The non‐isothermal crystallization process of the copolymers was analyzed by Avrami, Ozawa, Mo's, Kissinger, and Dobreva methods, respectively. The results showed that the crystallizability of PET was apparently enhanced with incorporating a small amount of PPG, which first rose and then reduced with increasing amount of PPG in the copolymers at a given cooling rate. The crystallization mechanism was a three‐dimensional growth with both instantaneous and sporadic nucleation. Particularly, PET‐co‐PPG containing 0.60 mol% PPG exhibited the highest crystallizability among all the copolymers. Copyright © 2015 John Wiley & Sons, Ltd.     

Electrospray micro liquid chromatography – Fourier transform infrared micro spectrometry

Microcolumn liquid chromatography has been interfaced with infrared microspectrometry by means of a novel technique involving electrospray nebulization. The eluent from the LC column is subjected to a high positive potential relative to the surroundings and the electric field generated charges the surface of the emerging liquid causing it to disintegrate into charged droplets which are attracted to an earthed, infrared-transparent, zinc selenide deposition plate. Nitrogen sheath gas is used to evaporate the solvent in the droplets, and the separated components are deposited on the zinc selenide plate for subsequent analysis by means of a Fourier transform infrared microscope and spectrometer. Provided low flow rates (～4 μl/min) are used, total elimination of the solvent is achieved and easily identifiable infrared spectra can be measured from less than 500 pg of sample (caffeine).     

An in situ Fourier transform infrared spectroscopy method for collecting real-time data for the liquid-phase reaction of CO2 and mono-ethanolamine in alcoholic solvent systems

A novel Fourier transform infrared (FTIR) spectroscopy method of analysis was developed to study the industrially important reaction of CO₂ with the primary amine, mono-ethanolamine (MEA), in n-propanol as representative alcoholic solvent. A semi-batch reactor with a piston like ‘floating’ head was specifically designed in order to study the reaction in the liquid phase, thereby eliminating the mass transfer limitations of a gas-liquid system. An attenuated total reflectance (ATR) probe was used to monitor the change in reagent and product concentrations in-situ. Successful spectral peak identification and calibrations were performed in order to collect real time, reaction kinetic data. Data analysis confirmed that the zwitterion reaction mechanism most accurately describes the reaction in non-aqueous systems.     

Water‐disintegrative and biodegradable blends containing poly(L‐lactic acid) and poly(butylene adipate‐co‐terephthalate)

In this study, novel biodegradable materials were successfully generated, which have excellent mechanical properties in air during usage and storage, but whose structure easily disintegrates when immersed in water. The materials were prepared by melt blending poly(L ‐lactic acid) (PLLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) with a small amount of oligomeric poly(aspartic acid‐co‐lactide) (PAL) as a degradation accelerator. The degradation behavior of the blends was investigated by immersing the blend films in phosphate‐buffered saline (pH = 7.3) at 40 °C. It was shown that the PAL content and composition significantly affected morphology, mechanical properties, and hydrolysis rate of the blends. It was observed that the blends containing PAL with higher molar ratios of L ‐lactyl [LA]/[Asp] had smaller PBAT domain size, showing better mechanical properties when compared with those containing PAL with lower molar ratios of [LA]/[Asp]. The degradation rates of both PLLA and PBAT components in the ternary blends simultaneously became higher for the blends containing PAL with higher molar ratios of [LA]/[Asp]. It was confirmed that the PLLA component and its decomposed materials efficiently catalyze the hydrolytic degradation of the PBAT component, but by contrast that the PBAT component and its decomposed materials do not catalyze the hydrolytic degradation of the PLLA component in the blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Nanofibrosis of uncrystallizable poly(lactide‐co‐glycolide) via phase separation

Poly(lactide‐co‐glycolide) (PLGA) copolymers are a kind of biocompatible and biodegradable materials being widely used in tissue engineering. However, phase separation had not been reported successfully in fabricating these amorphous polymers into nanofibrous matrix, although this technique had shown advantages over electrospinning in producing a nanofiber network. In this study, tetrahydrofuran (THF)/H₂O solvent pairs were found suitable solvents to induce the formation of uniform PLGA gel at selected gelation temperatures. The results indicated that fine nanofibrous structures with fiber diameter around 40–60 nm could be obtained following the steps of gel formation, solvent extraction, and freeze‐drying, by controlling the concentration of PLGA/THF/H₂O solution, THF/H₂O ratio, and gelation temperature. Copyright © 2009 John Wiley & Sons, Ltd.