Structure‐property relationships in exfoliated polyisoprene/clay nanocomposites

Structure‐property relationships in exfoliated polyisoprene (PI)/clay nanocomposites have been studied as a function of the clay concentration with rheometry, X‐ray diffraction, small‐angle X‐ray scattering, and transmission electron microscopy. The results presented here indicate that the interlayer spacing of layered silicates increases from 2 to at least approximately 14 nm because of the penetration of polymer molecules into the spacing between the silicate layers. The average aspect ratio (width/thickness) of the dispersed nanoplates is also estimated to be at least approximately 80. Additionally, the storage modulus of the nanocomposite exhibits frequency‐independent pseudo‐solidlike behavior above the percolation threshold [volume fraction of clay at the percolation threshold (?_p) = 0.02] and shows large enhancements (up to approximately six orders of magnitude) in comparison with the storage modulus of PI when the volume fraction of clay (?) is greater than ?_p. For the shear‐aligned PI/clay nanocomposites, an increase in the storage modulus with shear alignment is observed at ? < ?_p, whereas a decrease in the storage modulus is observed for ? > ?_p. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1000–1009, 2004     

Polymorphic behavior in syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods were used in an investigation of the structural changes in syndiotactic polystyrene (sPS)/clay nanocomposites. sPS/clay was prepared by the intercalation of sPS polymer into layered montmorillonite. Both X‐ray diffraction data and transmission electron microscopy micrographs of sPS/clay nanocomposites indicated that most of the swellable silicate layers were exfoliated and randomly dispersed in the sPS matrix. The X‐ray diffraction data also showed the presence of polymorphism in the sPS/clay nanocomposites. This polymorphic behavior was strongly dependent on the thermal history of the sPS/clay nanocomposites from the melt and on the content of clay in the sPS/clay nanocomposites. Quenching from the melt induced crystallization into the α‐crystalline form, and the addition of montmorillonite probably increased heterophase nucleation of the α‐crystalline form. The effect of the melt crystallization of sPS and sPS/clay nanocomposites at different temperatures on the crystalline phases was also examined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 736–746, 2002     

Poly(1‐butene)/clay nanocomposites: Preparation and properties

The preparation and properties of poly(1‐butene) (PB)/clay nanocomposites are described for the first time. Nanocomposites were prepared with the melt‐intercalation technique, using organically modified clay. The X‐ray diffraction patterns portrayed well‐defined diffraction peaks at higher d‐spacing than pristine clay, confirming the intercalation of polymer in silicate layers. Because PB exhibits time‐dependent polymorphism, the effect of clay on the phase transformation of PB was examined with thermal analysis. The phase transformation from a metastable tetragonal form to a stable hexagonal form was enhanced because of incorporation of layered silicates in the polymer matrix. The nanocomposites exhibited about a 40–140% increase in storage modulus depending on the clay content and significantly lower coefficient of thermal expansion. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1014–1021, 2003     

Mechanical properties of clay‐reinforced polyamide

Intercalated and exfoliated nanocomposites were prepared by extrusion and injection of polyamide‐6 and highly swollen or slightly swollen montmorillonite, respectively. The microstructure of the nanocomposites has been studied previously. In this article, we investigated the influence of the preferential orientation of the montmorillonite sheets on the mechanical properties of the nanocomposites. Dynamic mechanical analysis and tensile tests showed that the elastic modulus depends mainly on the filler loading. A parallel coupling could well account for the behavior of the nanocomposites. The calculated elastic and storage moduli of montmorillonite were set to 140 and 40 GPa, respectively. Compression tests were performed to study the anisotropy of the mechanical properties. The elastic modulus and flow strain were sensitive to the filler orientation. A Tandon–Weng approach was applied to consider the geometry of the filler. In all low‐deformation tests, no significant difference between intercalated and exfoliated systems was observed. Finally, the influence of the dispersion and exfoliation state of the filler on the ultimate properties of the nanocomposites (tensile tests) is discussed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 272–283, 2002     

Phase transition in polyamide‐66/montmorillonite nanocomposites on annealing

The crystalline‐phase transition in polyamide‐66/montmorillonite nanocomposites before melting was investigated by in situ X‐ray diffraction and is reported for the first time in this work. The phase‐transition temperature in the nanocomposites was 170 °C, 20 °C lower than that in polyamide‐66. The lower phase‐transition temperature of the nanocomposites could be attributed to the γ‐phase‐favorable environment caused by silicate layers. Meanwhile, the addition of silicate layers changed the crystal structure of the polyamide‐66 matrix and influenced the phase‐transition behavior. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 63–67, 2003     

Polyamide‐6/natural clay mineral nanocomposites prepared by solid‐state shear milling using pan‐mill equipment

The polyamide‐6 (PA6)/natural clay mineral nanocomposites were successfully prepared by solid‐state shear milling method without any treatment of clay mineral and additives. PA6/clay mixture was pan‐milled to produce PA6/clay compounding powder, using pan‐mill equipment. The obtained powder as master batch was diluted with neat PA6 to prepare composites by a twin‐screw extruder. The clay silicate layers were found to be partially exfoliated and dispersed homogeneously at nanometer level in PA6 matrix. The rheological measurements and mechanical properties of nanocomposites were characterized. The shear viscosities of nanocomposites were higher than that of pure PA6, and tensile strength and tensile modulus increased, but Izod impact strength decreased, with increasing concentration of clay. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 249–255, 2006     

Rheology of (±)‐camphor‐10‐sulfonic acid doped polyaniline‐m‐cresol conducting gel nanocomposites

The rheological behavior of polyaniline‐(±champhor‐10‐sulfonic acid)_0.5‐m‐cresol [PANI‐CSA_0.5‐m‐cresol] gel nanocomposites (GNCs) with Na‐montmorillonite clay (intercalated tactoids) is studied. The shear viscosity exhibits Newtonian behavior for low shear rate (<2 × 10^?4 s^?1) and power law variation for higher shear rate. The zero shear viscosity (η₀) and the characteristic time (λ) increase but the power law index (n) decrease with increase in clay concentration. In the GNCs storage modulus (G′) and loss modulus (G″) are invariant with frequency in contrast to the pure gel. The G′ and G′ exhibit the gel behavior of the GNCs up to 105 °C in contrast to the melting for the pure gel at 75.7 °C. The percent increase of G′ of GNCs increases dramatically (619% in GNC‐5) with increasing clay concentration. The conductivity values are 10.5, 5.65, 5.51, and 4.75 S/cm for pure gel, GNC‐1, GNC‐3, and GNC‐5, respectively, promising their possible use in soft sensing devices. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 28–40, 2008     

Synthesis,rheology, and morphology of nylon‐11/layered silicate nanocomposite

Exfoliated nylon‐11/layered silicate nanocomposites were prepared via in situ polymerization by dispersing organoclay in 11‐aminoundecanoic acid monomer. The original clay was modified by a novel method with 11‐aminoundecanoic acid. In situ Fourier transform infrared spectroscopy results show that stronger hydrogen bonds exist between nylon‐11 and organoclay than that of between nylon‐11 and original clay. The linear dynamic viscoelasticity of organoclay nanocomposites was investigated. Before taking rheological measurements, the exfoliated and intercalating structures and the thermal properties were characterized using X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and thermogravimetric analysis. The results show that the clay was uniformly distributed in nylon‐11 matrix during in situ polymerization of clay with 4 wt % or less. The presence of clay in nylon‐11 matrix increased the crystallization temperature and the thermal stability of nanocomposites prepared. Rheological properties such as storage modulus, loss modulus, and relative viscosity have close relationship with the dispersion favorably compatible with the organically modified clay. Comparing with neat nylon‐11, the nanocomposites show much higher dynamic modulus and stronger shear thinning behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2161–2172, 2006     

Synthesis and characterization of polyethylene/clay–silica nanocomposites: A montmorillonite/silica‐hybrid‐supported catalyst and in situ polymerization

A novel approach to the preparation of polyethylene (PE) nanocomposites, with montmorillonite/silica hybrid (MT‐Si) supported catalyst, was developed. MT‐Si was prepared by depositing silica nanoparticles between galleries of the MT. A common zirconocene catalyst [bis(cyclopentadienyl)zirconium dichloride/methylaluminoxane] was fixed on the MT‐Si surface by a simple method. After ethylene polymerization, two classes of nanofillers (clay layers and silica nanoparticles) were dispersed concurrently in the PE matrix and PE/clay–silica nanocomposites were obtained. Exfoliation of the clay layers and dispersion of the silica nanoparticles were examined with transmission electron microscopy. Physical properties of the nanocomposites were characterized by tensile tests, dynamic mechanical analysis, and DSC. The nanocomposites with a low nanofiller loading (<10 wt %) exhibited good mechanical properties. The nanocomposite powder produced with the supported catalyst had a granular morphology and a high bulk density, typical of a heterogeneous catalyst system. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 941–949, 2004     

Polymer/clay nanocomposites through multiple hydrogen‐bonding interactions

An 2‐ureido‐4[1H]pyrimidinone (UPy) motif with self‐association capability (through quadruple hydrogen bonds) was successfully anchored onto montmorillonite clay layers. Polymer/clay nanocomposites were prepared by specific hydrogen bonding interactions between surface functionalized silica nanoclays and UPy‐bonded supramolecular poly(ethylene glycol) or poly(?‐caprolactone). The mixed morphologies including intercalated layers with a non‐uniform separation and exfoliated single layers isolated from any stack were determined by combined X‐ray diffraction and transmission electron microscopic measurements. Thermal analyses showed that all nanocomposites had higher decomposition temperatures and thermal stabilities compared with neat polymer. The differential scanning calorimetric data implied that the crystallinity of polymers did not show essential changes upon introduction of organomodified UPy clays. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 650–658     

Synthesis and characterization of organosoluble,thermoplastic elastomer/clay nanocomposites

We synthesized organosoluble, thermoplastic elastomer/clay nanocomposites by making a jelly like solution of ethylene vinyl acetate containing 28% vinyl acetate (EVA‐28) and blending it with organomodified montmorillonite. Sodium montmorillonite (Na⁺‐MMT) was made organophilic by the intercalation of dodecyl ammonium ions. X‐ray diffraction patterns of Na⁺‐MMT and its corresponding organomodified dodecyl ammonium ion intercalated montmorillonite (12Me‐MMT) showed an increase in the interlayer spacing from 11.94 to 15.78 Å. However, X‐ray diffraction patterns of the thermoplastic elastomer and its hybrids with organomodified clay contents up to 6 wt % exhibited the disappearance of basal reflection peaks within an angle range of 3–10°, supporting the formation of a delaminated configuration. A hybrid containing 8 wt % 12Me‐MMT revealed a small hump within an angle range of 5–6° because of the aggregation of silicate layers in the EVA‐28 matrix. A transmission electron microscopy image of the same hybrid showed 3–5‐nm 12Me‐MMT particles dispersed in the thermoplastic elastomer matrix; that is, it led to the formation of nanocomposites or molecular‐level composites with a delaminated configuration. The formation of nanocomposites was reflected through the unexpected improvement of thermal and mechanical properties; for example, the tensile strength of a nanocomposite containing only 4 wt % organophilic clay was doubled in comparison with that of pure EVA‐28, and the thermal stability of the same nanocomposite was higher by about 34 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2065–2072, 2002     

Solidlike transition of melt‐intercalated biodegradable polymer/clay nanocomposites

Synthetic biodegradable aliphatic polyester (BAP) intercalated into organoclay was prepared by melt compounding, and its solidlike characteristics were investigated via several rheological test modes: steady shear rotation, oscillation, and creep testing. Structural investigations with X‐ray diffraction and transmission electron spectroscopy were also performed for a better understanding of the characteristic rheological behaviors. The creep, recovery, and stress modulus exhibited a solidlike transition of BAP/clay nanocomposites that depended on the clay content. An increase in the zero shear rate viscosity and a shifting of the crossover point (storage modulus vs loss modulus) to a lower frequency were also observed with increasing clay contents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2052–2061, 2003     

Effects of melt‐processing conditions on the quality of poly(ethylene terephthalate) montmorillonite clay nanocomposites

Organically modified montmorillonite was synthesized with a novel 1,2‐dimethyl‐3‐N‐alkyl imidazolium salt or a typical quaternary ammonium salt as a control. Poly(ethylene terephthalate) montmorillonite clay nanocomposites were compounded via melt‐blending in a corotating mini twin‐screw extruder operating at 285 °C. The nanocomposites were characterized with thermal analysis, X‐ray diffraction, and transmission electron microscopy to determine the extent of intercalation and/or exfoliation present in the system. Nanocomposites produced with N,N‐dimethyl‐N,N‐dioctadecylammonium treated montmorillonite (DMDODA‐MMT), which has a decomposition temperature of 250 °C, were black, brittle, and tarlike resulting from DMDODA degradation under the processing conditions. Nanocomposites compounded with 1,2‐dimethyl‐3‐N‐hexadecyl imidazolium treated MMT, which has a decomposition temperature of 350 °C, showed high levels of dispersion and delamination. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2661–2666, 2002     

Morphology and gas barrier properties of polyethylene‐based nanocomposites

Nanocomposites were processed by melt blending two reference matrices, a metallocene polyethylene and a low density maleic anhydride‐grafted polyethylene with an organo‐modified montmorillonite. It was shown that the introduction of a maleated polyethylene compatibilizer was required to improve the clay nanoplatelet dispersion in the metallocene polyethylene‐based nanocomposites. Increasing the montmorillonite content led to a significant increase of the barrier properties. Interfacial agents such as oxidized paraffins were shown to be more effective to reduce the gas permeability than maleated polyethylene and the dependence of the gas transport properties was discussed not only as a function of the clay dispersion but also as a function of the clay/compatibilizer and compatibilizer/matrix interactions. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 431–440, 2006     

Morphology and elastic modulus of novel poly[oligo(ethylene glycol) diacrylate]‐montmorillonite nanocomposites

Novel thermosetting poly[oligo(ethylene glycol) diacrylate]‐sodium montmorillonite nanocomposites containing a range of clay volume fractions were prepared by an in situ polymerization method. X‐ray diffraction showed that the basal plane spacing of the clay was increased to approximately 1.7 nm regardless of clay volume fraction. Transmission electron microscopy confirmed the basal spacing and intercalated structure. The elastic moduli of the composites were measured using ultrasonic pulse‐echo equipment. The results show that the Young's modulus and shear modulus increase with nominal clay volume fraction up to 0.22, and are in good agreement with the well‐established Christensen method and derived Hashin–Shtrikman bounds for conventional composites provided that the true volume fraction of clay reinforcement filler is calculated. At low clay volume fractions, the composites were transparent. When the nominal clay volume fraction was further increased, cracks and porous surfaces appeared, as observed by scanning electron microscopy. These defects decreased the elastic modulus, indicating an upper limit for clay additions in this preparation route. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1785–1793, 2005     

Preparation and characterization of poly(ethyl acrylate)/bentonite nanocomposites by in situ emulsion polymerization

Transparent poly(ethyl acrylate) (PEA)/bentonite nanocomposites containing intercalated–exfoliated combinatory structures of clay were synthesized by in situ emulsion polymerizations in aqueous dispersions containing bentonite. The samples for characterization were prepared through direct‐forming films of the resulting emulsions without coagulation and separation. An examination with X‐ray diffraction and transmission electron microscopy showed that intercalated and exfoliated structures of clay coexisted in the PEA/bentonite nanocomposites. The measurements of mechanical properties showed that PEA properties were greatly improved, with the tensile strength and modulus increasing from 0.65 and 0.24 to 11.16 and 88.41 MPa, respectively. Dynamic mechanical analysis revealed a very marked improvement of the storage modulus above the glass‐transition temperature. In addition, because of the uniform dispersion of silicate layers in the PEA matrix, the barrier properties of the materials were dramatically improved. The permeability coefficient of water vapor decreased from 30.8 × 10^?6 to 8.3 × 10^?6 g cm/cm² s cmHg. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1706–1711, 2002     

Shear‐induced change of exfoliation and orientation in polypropylene/montmorillonite nanocomposites

For the improved dispersion of montmorillonite (MMT) in a polypropylene (PP) matrix, PP/MMT nanocomposites prepared via direct melt intercalation were further subjected to oscillating stress achieved by dynamic packing injection molding. The shear‐induced morphological changes were investigated with an Instron machine, wide‐angle X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The original nanocomposites possessed a partly intercalated and partly exfoliated morphology. A transformation of the intercalated structure into an exfoliated structure occurred after shearing, and a more homogeneous dispersion of MMT in the PP matrix was obtained. However, the increase of the exfoliated structure was accompanied by the scarifying of the orientation of MMT layers along the shear direction. Some bended or curved MMT layers were found for the first time by TEM after shearing. However, the orientation of PP chains in the PP/MMT nanocomposites became very difficult under an external shear force; this indicated that the molecular motion of PP chains intercalated between MMT layers was highly confined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1–10, 2003     

Morphology and physical properties of polyethylene/silicate nanocomposite prepared by melt intercalation

Maleated polyethylene (PEMA)/silicate nanocomposites with a different aspect ratio of silicate and maleated PEMA/SiO₂ composite were prepared by melt intercalation. The nanocomposites with a high aspect ratio silicate (montmorillonite) showed a faster decrease in the terminal slope of the storage modulus and a steeper increase in complex viscosity than those with a low aspect ratio silicate (laponite) and SiO₂. The addition of montmorillonite increases the crystallization and the melting temperature of PEMA but decreases above 3 vol % of the silicate content because of the increased viscosity. The nanocomposite with montmorillonite showed the highest yield strength and secant modulus among the composites because of the highest aspect ratio of the filler. It also revealed strong interfacial adhesion with the matrix and orientation during tensile deformation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1454–1463, 2002     

Preparation and characterization of PP/clay nanocomposites based on modified polypropylene and clay

X‐ray diffraction and differential scanning calorimeter (DSC) methods have been used to investigate the crystallization behavior and crystalline structure of hexamethylenediamine (HMDA)‐modified maleic‐anhydride‐grafted polypropylene/clay (PP‐g‐MA/clay) nanocomposites. These nanocomposites have been prepared by using HMDA to graft the PP‐g‐MA (designated as PP‐g‐HMA) and then mixing the PP‐g‐HMA polymer in hot xylene solution, with the organically modified montmorillonite. Both X‐ray diffraction data and transmission electron microscopy images of PP‐g‐HMA/clay nanocomposites indicate that most of the swellable silicate layers are exfoliated and randomly dispersed into PP‐g‐HMA matrix. DSC isothermal results revealed that introducing 5 wt % of clay into the PP‐g‐HMA structure causes strongly heterogeneous nucleation, which induced a change of the crystal growth process from a three‐dimensional crystal growth to a two‐dimensional spherulitic growth. Mechanical properties of PP‐g‐HMA/clay nanocomposites performed by dynamic mechanical analysis show significant improvements in the storage modulus when compared to neat PP‐g‐HMA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3242–3254, 2005     

Poly(vinylidene fluoride)/clay nanocomposites prepared by melt intercalation: Crystallization and dynamic mechanical behavior studies

The preparation and properties of poly(vinylidene fluoride) (PVDF)/clay nanocomposites are reported for the first time. PVDF/clay nanocomposites were prepared by melt intercalation with organophilic clay. The composites were characterized with X‐ray diffraction, differential scanning calorimetry, and dynamic mechanical analysis. X‐ray diffraction results indicated intercalation of the polymer into the interlayer spacing. PVDF in the nanocomposites crystallized in the β form. Differential scanning calorimetry nonisothermal curves showed an increase in the melting and crystallization temperatures along with a decrease in crystallinity, as evidenced by the melting and crystallization peaks. Isothermal crystallization studies showed an enhanced rate of crystallization with the addition of clay, as evidenced by a reduction in the crystallization time. Dynamic mechanical analysis indicated significant improvements in the storage modulus over a temperature range of ?100 to 150 °C. The tan δ peak signifying the glass‐transition temperature of PVDF shifted to higher temperatures. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1682–1689, 2002