巯基-烯光点击反应辅助合成多官能度蓖麻油基聚氨酯丙烯酸酯

研究巯基-烯光点击反应辅助合成多官能度蓖麻油基聚氨酯丙烯酸酯。首先通过光引发的巯基-烯点击反应,于蓖麻油分子上引入巯基乙醇,形成多羟基化合物,然后加入丙烯酸羟丙酯与异佛尔酮二异氰酸酯,以物质的量为1:1反应得到端异氰酸酯丙烯酸酯,最终得到蓖麻油基聚氨酯丙烯酸酯。通过调节羟基含量可以得到不同官能度的丙烯酸酯。采用红外光谱、核磁氢谱、热重分析等手段表征其结构和性能,并测试了合成的聚氨酯丙烯酸脂的吸水率、附着力等性能,同时考察了它的热稳定性。结果表明, 在紫外光照射下,巯基和不饱和双键之间发生了加成反应;该聚合物的固化膜性能得到提高,尤其是硬度和热稳定性。由本文快速合成方法得到的树脂性能良好,具有较好的应用前景,扩大了巯基-烯光点击反应在高性能UV固化材料方面的应用范围。     

丙烯酸酯/聚氨酯三层核壳复合乳液的合成与表征

以自制的聚酯多元醇(PPMBA)、甲苯二异氰酸酯(TDI)、1,6-六亚甲基二异氰酸酯(HDI)、二羟甲基丙酸(DMPA)合成聚氨酯预聚体,再用丙烯酸酯类单体代替有机溶剂对预聚体降黏,封端预聚体后中和分散乳化得包含丙烯酸酯类单体的聚氨酯乳液.向乳液中加入引发剂引发自由基聚合得到复合乳液,最后再加入乙烯基类单体及引发剂合成三层核壳结构的聚丙烯酸酯/聚氨酯复合乳液.研究表明,二异氰酸酯的-NCO与聚酯多元醇中的-OH的物质的量之比(R值)为1.6~4之间时,随R值增加,乳液稳定性增强;DMPA含量在4%~7%的范围内,随DMPA含量的降低,乳胶膜的耐水性提高.通过红外光谱对所合成聚酯多元醇及复合乳液结构进行表征.     

巯基/(甲基)丙烯酸(甲基)烯丙酯光固化特性

通过对羧酸盐法改进后合成同时含有高活性的丙烯酸酯型C=C和低自由基活性的烯丙基型C=C的烯类单体(甲基)丙烯酸(甲基)烯丙酯,以实现(甲基)丙烯酸酯类紫外光固化与巯/烯光聚合结合在二元体系中;并以1173为光引发剂,利用实时红外(RT-IR)跟踪此类烯烃与三羟甲基丙烷三(3-巯基丙酸酯)(TMMP)光固化过程,探究烯烃结构、光强和引发剂用量对含有两类碳碳双键的烯类单体与巯基化合物二元体系的光固化行为的影响.研究发现,这类二元巯-烯光聚合反应中均有(甲基)丙烯酸酯双键的反应活性最大,(甲基)烯丙基次之,巯基的反应活性最小;甲基取代在烯烃的不同C=C上,对巯-烯光固化特性影响不同,甲基取代在烯丙基C=C上比甲基取代在丙烯酸基C=C上对巯-烯光固化行为影响更大;巯基最终转化率随甲基取代基数目增多而减少;丙烯酸甲基烯丙酯体系中两类双键(丙烯酸型/甲基烯丙基型)反应活性几乎相同且均具有高的转化率.     

基于二氧化碳共聚物的紫外光固化高分子材料的制备与性能

普通低分子量的二氧化碳共聚物由于预聚体中含有较多的亲水性端羟基, 在紫外光辐照下不能交联而降低材料的耐水性. 为降低亲水性端羟基对材料耐水性的影响, 本文利用锌钴双金属氰化物(Zn-Co DMC)催化剂实现了CO₂与4-乙烯基环氧环己烷、 环氧环己烷的三元无规共聚, 制备出分子量在40000以上, 含C=C双键的脂环族聚碳酸酯; 采用四(3-巯基丙酸)季戊四醇酯为固化剂, 基于紫外光诱导的双键-巯基点击反应制备了紫外光固化高分子材料. 研究发现, 在5.0 mJ/cm²的紫外光辐照剂量下即可制备出高透明硬化涂层, 在可见光(400~750 nm)波段内透光率达到97.5%, 铅笔硬度达到3H, 对马口铁等基体附着力达到0级. 值得指出的是, 该紫外光固化薄膜的玻璃化转变温度超过110 ℃, 与双酚A型环氧树脂相当, 而且不含苯环等结构, 具有更优异的耐紫外光老化性能.     

多官能团单体对超支化聚酰胺酯光固动力学及其固化膜热性能的影响

以1,1,1-三羟甲基丙烷为核,4-N,N-（2-羟乙基）-4-酮丁酸为单体,按照 一定比例,合成理论上第二代羟端基超支化聚酰胺酯,再与丙烯酰氯反应获得丙烯 酸化超支化聚酰胺酯预聚物（HAPAE-2-A）,它在光引发剂存在下经紫外光辐照可 以快速固化成膜。根据~1H NMR 谱测定所得产物的反应程度为85%。采用凝胶渗透 色谱和气相渗透法测定所得产物的分子量分布和数均分子量分别为2.16和1620 g/mol,与其理论分子量相比,其反应程度为89%,从而估算产物实际端基丙烯酸 酯双键数为10左右。采用光-差热分析仪研究HAPAE-2-A的反应动力学,发现当体系 中加入多官能团单体,如三羟甲基丙烷三丙烯酸酯、己二醇二丙烯酸酯和乙氧基一 缩二乙二醇丙烯酸酯时,多官能团单体的官能度及含量会对体系的最大光聚合反应 速率和不饱和双键的反应程度产生较大的影响。通过动态力学热性能测试发现 HAPAE-2-A光固化膜的玻璃态转化温度随多官能团单体的加入而提高。     

水性可紫外光固化的硫代聚氨酯分散体的制备

本文利用巯基-点击化学制备了一系列水性可光固化的硫代聚氨酯分散体,即通过连续的巯基-异氰酸酯和巯基-迈克尔加成反应分别合成硫代聚氨酯和聚硫醚：首先,二异氰酸酯与过量的二元硫醇反应生成端基为巯基的硫代聚氨酯低聚物,然后与合成的二丙烯酸酯单甲基丙烯酸酯进行巯基-迈克尔加成反应,得到侧基为甲基丙烯酸酯的硫代聚氨酯树脂,最后,巯基乙酸与端基上的丙烯酸酯反应,提供树脂的亲水基团。将树脂分散在水中后,得到半透明的可光固化硫代聚氨酯分散体。树脂的主链上含有硫醚键,可以有效克服氧阻聚效应,得到较高的转化率;侧基上带有很多可光聚合的甲基丙烯酸酯基团,光聚合后固化膜的交联密度非常高,因而也具有较高的玻璃化转变温度。     

新型苯甲酰甲酸酯光引发剂的合成及其性能

以苯甲酰甲酸和二缩三乙二醇为原料,经酯化反应合成了一种新型的光引发剂苯甲酰甲酸二缩三乙二酯(2),其结构和性能经¹H NMR, ¹³C NMR, FT-IR, HR-MS,元素分析和TG表征。紫外光谱分析显示2的最大吸收峰位于251.1 nm和298.8 nm。2能有效引发含双键的聚氨酯丙烯酸酯与单体的光聚合反应,光固化时间小于1 min,固化膜性能良好。     

可聚合二苯甲酮类光引发剂的合成及其光聚合性能研究

以4-(2,3-环氧丙氧基)二苯甲酮(EBP)和丙烯酸为原料,通过开环反应合成了含有不饱和双键的可聚合光引发剂4-(丙烯酸-2-羟基丙酯-3-氧基)二苯甲酮(AEBP).采用红外光谱(FT-IR)、核磁共振氢谱(¹HNMR)对其结构进行表征,利用紫外吸收光谱对AEBP的紫外吸收波长进行表征,通过实时红外(RT-IR)研究了AEBP引发丙烯酸酯单体的光聚合动力学.采用萃取法对比了BP与AEBP引发固化体系后的迁移性.结果表明,随AEBP浓度增加,单体最终转化率增加;当助引发剂N,N-二甲氨基苯甲酸-乙酯(EDAB)浓度为1.2%时,单体最终双键转化率最高;AEBP对双官能度单体的引发效率较之三官能度单体的好;聚合速率随光照强度的增强而变快;固化后AEBP的迁移性比传统的BP大大降低.     

ε-己内酯改性聚氨酯丙烯酸酯的制备及电子束固化涂料性能研究

本文以甲基丙烯酸羟乙酯、ε-己内酯及异氟尔酮二异氰酸酯为原料制备了己内酯改性聚氨酯丙烯酸酯。使用傅里叶变换红外光谱(FT-IR)和核磁共振氢谱(~1HNMR)表征了产物结构。探究了ε-己内酯链段含量对改性聚氨酯丙烯酸酯树脂黏度的影响,并进一步对比研究了其电子束(EB)固化膜和紫外光(UV)固化膜的热机械性能、拉伸性能和涂层基本性能的差异。     

2-(4-甲氧基苯基)-4,6-双(三氯甲基)-S-三嗪光引发剂的合成及其光聚合动力学性能研究

以对甲氧基苯甲腈和三氯乙腈为原料合成了光引发剂2-(4-甲氧基苯基)-4,6-双(三氯甲基)-S-三嗪(MBTT),通过傅里叶红外光谱仪、核磁共振仪和紫外吸收光谱对所合成的产物结构进行了表征.并利用实时红外(RT-IR)对该引发剂进行了光聚合反应动力学研究,考察了单体、引发剂浓度和光强对引发速率及单体转化率的影响.结果表明,MBTT是一种高效的紫外光引发剂,在引发剂用量为0.1%时光聚合的单体转化率就能达到90%;随着光强的增大,单体的双键转化率和最大反应速率都增大,诱导期缩短;双丙烯酸酯类单体的双键转化率比三丙烯酸酯类单体的双键转化率要高.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.