含水状态对细菌纤维素/聚苯胺复合凝胶膜制备及性能的影响

以不同含水量细菌纤维素为模板,苯胺单体为原料原位聚合生成聚苯胺,制备出不同含水量细菌纤维素/聚苯胺(HBC/PANI、LBC/PANI及DBC/PANI)复合凝胶膜,系统研究了细菌纤维素凝胶膜含水量和反应时间对苯胺原位聚合以及复合凝胶膜微观形貌、电学性能和力学性能的影响.扫描电镜照片表明聚苯胺均匀包覆在BC纤维上形成导电网络结构;四探针测试表明聚合时间90 min时导电率最高;低含水量加快了聚合反应速度,提高了复合凝胶膜的电导率,而完全干燥则使电导率降低;交流阻抗测试也表明低含水量可以明显提高材料的离子导电性;力学性能测试结果表明了BC/PANI复合凝胶膜具有良好的机械性能,抗拉强度可达0.21 MPa,同时低含水量不会降低复合凝胶膜的力学性能.     

导电聚苯胺/钙基膨润土复合材料的制备

采用插层聚合法制备了导电聚苯胺/钙基膨润土、聚苯胺/有机化膨润土复合材料.以电导率为考核指标,通过正交设计优化了苯胺的加入量、反应温度和反应时间等参数.结果表明,苯胺的加入量影响较显著,反应温度对聚苯胺/有机化膨润土复合材料影响较聚苯胺/钙基膨润土体系明显,反应时间的延长,有利于聚苯胺/有机化膨润土复合材料电导率的提高.聚苯胺/钙基膨润土复合材料制备的最佳工艺条件为:苯胺加入量为70%,反应温度为0℃,反应时间为6 h;聚苯胺/有机化膨润土复合材料制备的最佳工艺条件为:苯胺加入量为70%,反应温度为室温,反应时间为8 h.利用红外光谱(FT-IR)、X射线衍射(XRD)和四探针技术表征了材料的组成、结构和性能.结果表明:膨润土经有机化后,晶面间距增大较多;苯胺单体与钙基膨润土插层聚合后,膨润土晶面间距增大不多;苯胺单体与有机化膨润土复合后,破坏了膨润土的晶格结构,形成了混杂复合体系,电导率达10-3S.cm-1.     

聚酰胺/聚苯胺导电复合材料制备方法的研究进展

聚酰胺材料是一种重要的工程塑料和合成纤维原料,解决材料使用过程中的表面静电堆积问题是提升材料性能、扩展其应用领域的重要研究方向,因此发展了多种通过物理与化学的方法研究制备抗静电聚酰胺材料的技术.聚苯胺以其单体原料易得、合成工艺简单、掺杂现象独特、电导率较高、在空气中具有良好的稳定性等特点,被认为是最有前途的导电高分子之一,但其缺点也很明显,即加工性能很差.以聚苯胺作为抗静电剂与聚酰胺复合,不但大大提高了聚酰胺材料在应用于织物、涂料、输油管等领域时的抗静电性能,还可以解决聚苯胺的加工问题.基于近年来聚酰胺/聚苯胺导电复合材料的制备方法和复合材料特性,综述了聚酰胺/聚苯胺复合纤维、复合薄膜、复合粉末、三相复合等导电复合材料体系的制备方法、研究进展及应用领域.     

聚苯胺/PA-6导电复合膜的电化学合成与性能

用电化学复合法，以聚己内酰胺为膜基，通过氟硼酸掺杂，使苯胺电解聚合，制成一种新型的聚苯胺／聚己内酰胺（ＰＡｎ／ＰＡ－６）复合膜，考察了电流密度、掺杂剂浓度及苯胺浓度等因素对导电复合膜的电导率、机械性能的影响。     

原位聚合法制备PANI/PET导电织物及其性能分析

在聚酯纤维基材及其织物表面,原位聚合形成厚度约1~2μm聚苯胺包覆层,制得聚苯胺(PANI)/聚酯(PET)导电织物.PANI层优异的导电性能使之成为有广阔发展前景的柔性电磁屏蔽材料.正交试验分析研究了苯胺单体浓度、氧化剂:苯胺摩尔比、掺杂酸浓度、反应时间对PANI包覆层外观形态、与基体结合牢度以及导电性的影响.实验表明:在经适当前处理的PET基材表面,以苯胺单体浓度为0.25mol/L、氧化剂与苯胺摩尔比为1∶1、掺杂酸浓度0.5 mol/L、反应时间60 min、反应温度为0~20℃时制备的PANI/PET导电织物方阻最小,导电性最好;掺杂酸酸性越强,导电性越好.SEM、FTIR及XRD测试表明涤纶织物表面有均匀连续的聚苯胺膜存在.分析表明聚苯胺分子链中氧化结构与还原结构含量基本相等,说明聚苯胺渗入纤维内部,使纤维无定形区面积增加,结晶度减小.     

盐酸掺杂制备导电性聚苯胺的工艺优化研究

掺杂是获得高导电性聚苯胺的重要手段.本文采用盐酸进行掺杂,通过实验研究了不同条件下盐酸掺杂对聚苯胺基本性能的影响,优化了制备聚苯胺的工艺条件.当过硫酸铵与苯胺比为1时,聚合产率高达66.14%;当盐酸浓度为1.5mol/L时,室温下反应12h导电性最好.制备了聚苯胺样品,并对样品进行了FT-IR、SEM、XRD测试.结果均表明盐酸掺杂聚苯胺的反应主要发生在醌环上,掺杂后聚苯胺有一定的结晶性,且呈微纳米颗粒状、分布均匀,电导率达到1.29S·cm~(-1).正交试验得出的优化工艺为:盐酸浓度为1.0mol·L~(-1),氧化剂与苯胺单体摩尔比为1∶1,室温条件下反应4h.     

复合酸掺杂导电聚苯胺的性能研究

以苯胺为单体、过硫酸胺为氧化剂,由化学氧化聚合法在磺基水杨酸和硫酸的复合酸的水溶液中合成导电聚苯胺,并通过压片法、激光粒度分析、扫描电镜、差热分析及红外光谱对掺杂态聚苯胺的电导率、表面形貌及结构进行了研究.结果表明,复合酸掺杂聚苯胺的热稳定性比仅用硫酸掺杂聚苯胺的有了很大的提高;所得导电聚苯胺的粒度分布比较均匀(平均粒径约15.4μm);复合酸掺杂使聚苯胺分子链上的电荷呈离域化,掺杂程度提高.     

炭黑/聚苯胺纳米复合粒子的制备与表征

用现场原位聚合法制备了炭黑/聚苯胺纳米复合粒子,讨论了聚合反应条件对产物电导率的影响,并表征了复合粒子的形态和耐热性能.结果表明,所得的炭黑/聚苯胺纳米复合粒子粒度约为50 nm并具有核-壳结构,其电导率达30 S.cm-1,热分解温度约为600℃.     

聚苯胺的合成及其摩擦学行为的研究

选择合适的ＳＤＢＳ／ 苯胺／ 水三组分Ｏ／Ｗ 微乳液与苯胺单体共存的两相体系,以单体相为单体源,在Ｏ／Ｗ 三组分微乳液中进行了苯胺聚合,成功地制备出了能够稳定分散于石腊油的聚苯胺微粒。并在四球试验机上研究合成条件、负荷、浓度对其摩擦学行为的影响。结果表明：聚苯胺有一定的减摩抗磨效果     

改性芳纶/聚苯胺复合导电纤维的制备

以聚对苯二甲酰对苯二胺(简称芳纶,PPTA)纤维为基材,使用环氧氯丙烷(ECP)对PPTA表面进行有机修饰,得到了ECP改性的PPTA纤维(ECP-PPTA),然后使苯胺单体在ECPPPTA表面接枝聚合,制备了ECP-PPTA/PANI复合导电纤维。用傅里叶变换红外分光光度计(FT-IR)、扫描电子显微镜(SEM)、热重分析仪(TGA)及X射线衍射分析仪(XRD)等分析测试方法对ECP-PPTA及ECP-PPTA/PANI复合导电纤维进行了表征。结果表明:PPTA经ECP改性后,PANI成功接枝在PPTA表面,制备的ECP-PPTA/PANI复合导电纤维的电阻率低于PPTA/PANI纤维的,其室温电阻率最低为0.32MΩ·m。     

Preparation and characterization of polyaniline-containing Na-AlMCM-41 as composite material with semiconductor behavior

Composite material formed from a mesoporous aluminosilicate, Na-AlMCM-41, with conducting polyaniline (PANI) has been synthesized by an in situ polymerization technique. Studies of aniline adsorption over mesoporous Na-AlMCM-41 synthesized in our laboratory allowed us to find the modes in which aniline interacts with the active sites of Na-AlMCM-41. In order to obtain the best reaction conditions to polymerize aniline onto Na-AlMCM-41, aniline was first polymerized to produce pure PANI. Hence, the oxidative in situ polymerization was carried out by two procedures, differing in the polymerization time and in static or stirring conditions. Studies of infrared spectroscopy and UV-vis spectroscopy indicated that higher polymerization time and static conditions allowed us to obtain mainly polyaniline in emeraldine form on the host. The N(2) isotherm of the polyaniline/Na-AlMCM-41 composite (PANI/MCM) indicated that the shape was similar to that of MCM, but the shift to saturation transition to lower partial pressure shows that the channels are occupied by PANI and they are now narrowed. The thermal properties of PANI, Na-AlMCM-41, and composite were investigated by TGA analyses and we found that the polymer shows higher thermal stability when it is forming the composite. Scanning electron microscopy indicated that PANI is not on the outer surface of the host. Conductivity studies show that PANI/Na-AlMCM-41 exhibits semiconductor behavior at room temperature and its conductivity was 7.0 x 10(-5) S/cm, smaller than that of pure polyaniline. PANI/Na-AlMCM-41 conductivity shows an increase as temperature increases. Magnetic measurements at room temperature confirmed that the composite has paramagnetic behavior; at lower temperatures the composite became diamagnetic.     

Enhancement of polyaniline’s electrical conductivity by coagulation polymerization

An effective and simple method was developed to prepare highly conductive polyaniline by coagulation polymerization. Depending on the coagulation reaction between aniline salts and lauryl sulfonate (SDS), not only was the polymerization rate of aniline monomers greatly decreased but also the doping efficiency of hydrochloric acid was effectively increased. Low polymerization rate provided enough time for the conformation adjustment of polyaniline chains and the diffusion of doping agent. Meanwhile, the doping efficiency of hydrochloric acid on polyaniline chains was effectively increased due to its easy diffusion among many vacancies, which were generated when SDS separated in the process of polymerization. Therefore, the electrical conductivity of polyaniline prepared by coagulation polymerization was increased more than ten times than that of polyaniline, which was prepared by conventional methods. In addition, the important factors to influence the preparation, such as SDS concentration, hydrochloride acid (HCl) concentration, content of ammonium persulfate (APS), and polymerization time were also investigated. When the molar ratio (aniline:SDS:HCl :APS) was set to 1.69:0.46:15.38:1, the conductivity of polyaniline reached 24.39 S/cm.     

聚苯胺/纳米二氧化锰复合材料Ⅰ.原位氧化合成制备

用固相合成法制备了纳米二氧化锰(nm-MnO2),并通过原位聚合法制备了聚苯胺／纳米二氧化锰复合材料。研究结果表明：在苯胺／nm-MnO2的盐酸反应体系中,nm-MnO2可以使苯胺氧化聚合。在一定的nm-MnO2用量下,聚苯胺的产率随苯胺添加量的增加而下降,nm-MnO2在产物中的含量也随之下降,且含量很低。在苯胺：／nm-MnO2／过硫酸铵的反应体系中,研究了Nm-MnO2通过两种不同的加料方式原位制备PA-NI／nm-MnO2复合材料的合成条件。第一种方式为nm-MnO2和过硫酸铵同时与苯胺混合,一起参与苯胺的氧化聚合。第二种方法是先将过硫酸铵和苯胺混合,3min后再将nm-MnO2加入反应体系中。研究表明：第一种加料方式得到的队NI／nm-MnO2中nm-MnO2的含量很低;第二种加料方式可以得到高nm-MnO2含量(w=0．14-0．73)的产物,其电导率约10^-4S／cm。     

电聚合苯胺过程的在线紫外-可见光谱

用在线紫外-可见光谱电化学的方法对0.5mol/L硫酸水溶液中苯胺在ITO导电玻璃电极上的电化学聚的过程进行了研究.结果表明在循环伏安条件下苯胺发生了电聚合,聚合速率与苯胺浓度成正关系;而且在线紫外-可见电化学光谱表明,在0.01mol/L苯胺溶液的电聚合过程的诱导期较长.恒电位条件下的在线紫外-可见电化学光谱显示苯胺浓度为0.05mol/L,电位为0.8V时,在ITO电极上苯胺低聚合物中间体可能产生于聚苯胺形成之前;而0.01mol/L苯胺在0.8V电位下不发生聚合,但在线紫外-可见光谱又显示此时在电极上可能存在小的苯胺低聚物的中间体;在线紫外-可见光谱表明这种中间体是可能产生并存在电极表面上的.     

用氧化偶联聚合法合成新型电活性聚酰胺及其结构表征

使用氧化偶联聚合的方法, 合成了一种新的电活性聚酰胺, 使其同时具有聚酰胺和聚苯胺性质. 该反应操作简便易行, 室温下即可进行. 通过红外光谱和核磁共振谱对其结构进行了表征, 用紫外-可见光谱和循环伏安法研究了氧化还原性质和电活性, 并测试了导电率.     

聚苯胺／聚乙烯醇导电复合膜的制备及性质研究

用较简单的化学氧化现场吸附聚合法（ｉｎ－ｓｉｔｕｐｏｌｙｍｅｒｉｚａｔｉｏｎ）制得了聚苯胺（ＰＡｎ）／聚乙烯醇（ＰＶＡ）导电复合膜．该膜具有较好的导电性和机械性能；其电导率可达５．８ｓ／ｃｍ，拉伸强度达１３ＭＰａ，断裂伸长率为１１０％左右．本文讨论了制备的各种条件对复合膜导电性能及力学性能的影响、稳定性及电化学活性；并采用循环伏安曲线、扫描电镜（ＳＥＭ）、ＦＴＩＲ谱及元素分析对该复合膜的结构和性能进行了表征．     

Plasma polymerization of aniline on different surface functionalized substrates

The plasma polymerization of aniline on different surface functionlized low-density polyethylene (LDPE) substrates was investigated, and the resulting polymer was characterized by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, and atomic force microscopy. The results showed that the structure of plasma-polymerized polyaniline was rather different from polyaniline synthesized by conventional chemical and electrochemical methods. This difference may be due to extensive coupling reactions and cross-linking reactions during the plasma polymerization process. The use of acrylic acid graft copolymerized LDPE substrate significantly enhanced the adhesion of the polyaniline to the substrate over that observed with pristine LDPE. The plasma polymerized polyaniline can be rendered electrically conductive if the polymerization is carried out on a polystyrenesulfonic acid-coated LDPE substrate. Conductivity can also be induced by acid protonation of the polyaniline by HClO(4). The reaction of the plasma-polymerized polyaniline with viologen grafted on the substrate under UV irradiation and with AuCl(3) and Pd(NO(3))(2) in acid solutions was also investigated.     

Electrochemical synthesis and characterization of solid-phase microextraction fibers using conductive polymers: application in extraction of benzaldehyde from aqueous solution

In this work, polyaniline, polypyrrole, and polyaniline/polypyrrole composite fibers were synthesized in the absence and presence of oxidized multiwalled carbon nanotubes using electrochemical cyclic voltammetry with CF₃COOH as dopant. Thermal stability of these fibers was studied by differential scanning calorimetry. Then, headspace solid-phase microextraction process coupled with gas chromatography and flame ionization detector was used for comparing extraction capability of benzaldehyde from aqueous solution. Since polyaniline fiber showed better extraction efficiency than the other fibers, its preparation conditions including acid concentration, aniline concentration, scan rate, and amount of multiwalled carbon nanotubes were studied by means of the “one-factor-at-a-time method”. The analytical performance of polyaniline fibers were investigated to determine benzaldehyde from the aqueous solution. The morphology and texture of polyaniline fibers were examined by field emission scanning electron microscopy and Fourier transform infrared spectroscopy analyses. The attained results revealed that the perfect conditions for acid concentration, aniline concentration, scan rate, and multiwalled carbon nanotubes content were 0.5 M, 0.2 M, 25 mV s^?1, and 0.02 wt%, respectively. The limit of detection for the proposed polyaniline fiber was 15 ng ml^?1.     

二磺酸掺杂高热稳定性导电聚苯胺的合成及性能

以有机二磺酸作为掺杂剂合成了具有高热稳定性的二磺酸掺杂导电聚苯胺。研究了反应时间、温度、酸/苯胺摩尔比等因素对产率、产物的导电率与分子量的影响。利用微波加热的方法测试有机二磺酸掺杂聚苯胺的热稳定性能，结果表明：有机二磺酸掺杂的导电聚苯胺在微波场中升温速率快，并且具有良好的反复升温性能。