高温燃煤钙基纳米金属氧化物复合吸附剂同时除砷脱硫研究

将纳米MgO、Al2O3和ZnO分别添加于超细CaCO3中制备出钙基纳米金属氧化物复合吸附剂,并进行燃煤过程中除砷脱硫的试验研究。结果表明,在Ca/S摩尔比为1.8,燃烧温度为1200℃,纳米金属氧化物的添加量为超细CaCO3质量的8%时,添加了纳米MgO的复合吸附剂除砷脱硫性能最好,比单一的超细CaCO3除砷率和脱硫率分别高出了28.73%和37.21%,表现出同时除砷脱硫的良好性能。     

喷涂法构筑二氧化硅纳米粒子涂层及其光学和润湿性质

采用Stöber方法,通过调节反应温度及乙醇和水的体积,合成了不同粒径的二氧化硅纳米粒子.以合成的粒径为20 nm的二氧化硅纳米粒子为原料,采用简单、方便的喷涂方法在玻璃片上构筑了纳米粒子涂层.在550 ℃煅烧二氧化硅纳米粒子涂层,增强了二氧化硅纳米粒子在玻璃片上的附着力.用1H, 1H, 2H, 2H-全氟辛基三乙氧基硅烷修饰之后,二氧化硅纳米粒子涂层的表面润湿性由亲水性转变为疏水性.通过喷涂法制备的二氧化硅纳米粒子涂层具有减反增透效果,当二氧化硅纳米粒子质量分数为0.48%、循环喷涂沉积数为3时,涂层在可见光范围内的最大透光率可达95.5%.用扫描电子显微镜观测涂层表面形貌发现,喷涂法制备的涂层是均匀的、可控的.喷涂技术构筑纳米粒子涂层具有简单快速、可大面积应用等优点.     

金属氧化物涂层钛阳极的研究*

金属氧化物涂层钛阳极是指在以钛为阳极的基体表面涂上金属氧化物的电极,简称DSA。本文综述了钛基金属氧化物涂层电极的研究进展,包括钛基钌系涂层电极、钛基锡系涂层电极、钛基铅系涂层电极,以及其它氧化物涂层电极。评述了多元化钛基涂层的性能、各种涂层制备方法的优势与不足,阐明了掺杂稀土以及添加中间层对钛阳极的影响,同时展望了钛基金属氧化物涂层电极的发展方向。     

锑掺杂二氧化锡(ATO)纳米颗粒:共沸蒸馏干燥法制备及隔热性能

以五水合四氯化锡、三氯化锑为原料,乙醇为溶剂,氨水为沉淀剂,乙酸异戊酯为共沸溶剂,共沸蒸馏干燥前驱体溶胶,650℃煅烧后制备了单分散不同锑掺杂量的掺锑二氧化锡(ATO)纳米颗粒。结果表明,锑含量对颗粒粒径、光电性质具有重要影响,10mol%锑掺杂量时,样品具有最低的电阻率以及最优良的光学性质(最高的可见光透过率与近红外屏蔽效果),电学性质。ATO与聚氨酯复合涂膜玻璃隔热测试表明,涂层薄膜具有优良的隔热效果,能够有效地减小热量的传递与扩散。     

锑掺杂二氧化锡（ATO）纳米颗粒：共沸蒸馏干燥法制备及隔热性能

以五水合四氯化锡、三氯化锑为原料,乙醇为溶剂,氨水为沉淀剂,乙酸异戊酯为共沸溶剂,共沸蒸馏干燥前驱体溶胶,650℃煅烧后制备了单分散不同锑掺杂量的掺锑二氧化锡（ATO）纳米颗粒。结果表明,锑含量对颗粒粒径、光电性质具有重要影响,10mol%锑掺杂量时,样品具有最低的电阻率以及最优良的光学性质（最高的可见光透过率与近红外屏蔽效果）,电学性质。ATO与聚氨酯复合涂膜玻璃隔热测试表明,涂层薄膜具有优良的隔热效果,能够有效地减小热量的传递与扩散。     

纳米锌/对氨基苯磺酸/环氧丙烯酸酯涂层的阻燃性能研究

为探讨纳米锌与对氨基苯磺酸对环氧丙烯酸酯(EA)涂层的阻燃效果,以乙酸锌和苜蓿粉为原料,利用植物还原法制备了纳米锌,将其与对氨基苯磺酸及EA配合,经紫外光固化制备纳米锌/对氨基苯磺酸/EA阻燃涂层。通过透射电镜、X-射线衍射仪、红外、紫外、差示扫描量热仪及力学分析仪对其纳米锌及上述阻燃涂层的结构、阻燃、透光率、热稳定性及硬度等性能进行测定。结果表明:合成的纳米锌的径粒为3. 8±0. 8 nm,其特征衍射峰与单质锌晶体的相吻合;当纳米锌添加量为1. 0 g时,纳米锌/对氨基苯磺酸/EA涂层阻燃性能最佳,涂层残炭率达19. 47%,极限氧指数达31。所有涂层硬度均大于5 H,涂层热稳定性随纳米锌添加量的增加而增加。涂层热降解分析表明纳米锌和对氨基苯磺酸能有效提高涂层阻燃和热稳定性。本实验为阻燃EA涂层提供了一种有效的阻燃改性方法。     

二氧化硅纳米颗粒/硅树脂复合超疏水功能涂层的制备和性能研究

将二氧化硅纳米颗粒和硅树脂制成混合液,采用喷涂法(spray-coating)制备出了具备超疏水性的复合涂层.研究了二氧化硅、硅树脂不同含量配比对涂层疏水性能的影响,结果表明复合涂层的接触角随二氧化硅含量的增加而增加.在二氧化硅含量大于3%(质量分数)时,涂层显现超疏水性;当二氧化硅含量为3%(质量分数)、硅树脂含量为7%(质量分数)时,涂层与水的接触角达到151.6°,滚动角接近0°.通过扫描电子显微镜(SEM)观察涂层表面的微观结构,发现超疏水性的涂层具备微-纳复合阶层结构,类球状突起粒径在5μm左右,类球状突起上分布纳米团聚颗粒,直径约为50 nm.这种类似荷叶表面的微(纳复合阶层结构,结合硅树脂的低表面能,使得复合涂层具备了超疏水性能.     

纳米氧化锡锑改性水性聚氨酯的制备与表征

以异佛尔酮二异氰酸酯(IPDI)、聚醚二醇（N-210）、二羟甲基丙酸（DMPA）、一缩二乙二醇（DEG）、三羟甲基丙烷（TMP）及纳米氧化锡锑（ATO）浆料为主要原料,制备了稳定的纳米ATO改性水性聚氨酯(APU)乳液。 粒径测试及透射电子显微镜（TEM）观察显示,纳米ATO在水性聚氨酯中分散较好,乳液粒径均小于100 nm; FTIR分析表明,纳米ATO粒子与水性聚氨酯(WPU)间可能存在化学键; 热重分析(TGA)测试显示,随纳米ATO添加量的增加,胶膜最大热分解温度逐渐提高,最大提高了约20 ℃;紫外-可见-近红外吸收及保温性能测试表明,随着纳米ATO添加量的提高,胶膜在800~2500 nm的透过率逐渐降低,但涂层在可见光区透过率均超过70%,热阻率由1.34×10-2 m2·℃/W提高至3.17×10-2 m2·℃/W。     

纳米金属氧化物：复合分散法制备及分散性

通过采用水热晶化与荷电复合分散法制备γ-AlOOH、R-TiO₂和α-Al₂O₃纳米晶体粉末,利用TEM和激光粒度分析仪等手段研究了纳米颗粒水热晶化与荷电复合分散的分散效果及其工艺条件,并探讨了金属氧化物纳米颗粒水热晶化与荷电复合分散机理。结果表明,晶化与荷电复合分散可明显改善金属氧化物纳米颗粒在液相中的分散稳定性,所制得的AlOOH、TiO₂和Al₂O₃纳米颗粒在水中分散放置24 h后的透光率的变化率D₂₄还可分别保持为94.1%、87.7%和82.2%;在水中分散后的粒径分布统计的平均粒径分别为67、70和143 nm。     

碳纳米粒子:合成及可见光催化降解萘酚绿

以酒石酸和酪氨酸为起始反应物,乙二醇为溶剂,采用溶剂热法一步合成了高发光强度的碳纳米粒子。利用XRD、TEM、FTIR和荧光光谱对碳纳米粒子的物相、形貌和粒径、表面基团及发光性能进行了表征。结果表明,合成的碳纳米粒子为粒径分布集中的球形,粒径10~30 nm,分散性好,表面富含-COOH、-OH等官能团,具有激发波长依赖的光致发光特性。考察了反应温度、酒石酸与酪氨酸质量比对碳纳米粒子发光性能的影响。研究了碳纳米粒子/H2O2催化体系对萘酚绿的降解性能,结果表明:130 mg·L-1的萘酚绿溶液,可见光照射3.5 h降解率可以达到96%。荧光光谱法表征指明降解过程中有羟基自由基生成。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.