Optimization of HPLC-ICP-AES for the determination of arsenic species

High performance liquid chromatography coupled to ICP-AES detection provides a rapid, reliable and sensitive method for arsenic speciation. The separation of As(III), As(V), DMA and MMA was achieved with ion exchange chromatography coupled to an axially-viewed sequential ICP-AES. After optimization of the chromatographic parameters (pH and concentration of the mobile phase), a careful study of the interface was conducted. Five nebulizers associated to three spray chambers were tested. Response of the ICP to each arsenic species was strongly affected by the selection of the nebulizer and spray chamber, however similar responses were obtained for each arsenic species. Best signal-to-noise ratios were obtained by using a microconcentric nebulizer and a cyclone spray chamber and did not affect the chromatographic resolution. Detection limits better than 10 microg L(-1) were obtained for As(III), DMA, MMA and 20 microg L(-1) for As(V), which is a significant improvement over previously published results.     

Elemental speciation by liquid chromatography-inductively coupled plasma mass spectrometry with direct injection nebulization.

A new version of the direct injection nebulizer (DIN) is used to interface liquid chromatographic (LC) separations with element-selective detection using inductively coupled plasma mass spectrometry (ICP-MS). The DIN injects all of the sample into the ICP and has a dead volume of less than 1 microliter. Charged species of arsenic and tin are separated as ion pairs on a micro-scale (1 mm i.d.), packed, reversed-phase column. Detection limits are 0.2-0.6 pg for arsenic and 8-10 pg for tin. For methanol + water eluents, the signal is highest at 25% methanol and stays within 25% of this maximum as the methanol fraction is varied from 20 to 80%. Compared with LC-ICP-MS with conventional nebulizers, the absolute detection limits and chromatographic resolution are substantially superior, and the dependence of analyte signal on solvent composition is somewhat less severe with the DIN.     

Characterization of a nebulizer interface for flame atomic absorption spectroscopy

In this paper we describe and characterize a nebulizer “interface” for flame atomic absorption spectroscopy (FAAS). A nebulizer interface should provide for optimum coupling of analytical liquid flow techniques, e.g. flow injection analysis and liquid chromatography, to FAAS instruments. When the interface is used instead of one of the conventional nebulizer systems together with a FAAS instrument, a 3–5 times better characteristic concentration and detection limit were obtained for the test element Mn. The interface facilitates the coupling of analytical low-flow rate devices to FAAS instruments and simplifies the optimization of flame stoichiometry. The nebulizer interface provides for complete utilization of the sample (no waste). When the interface is used to connect a high performance liquid chromatography system to a FAAS instrument, the resulting increase in peak width is approximately 1 s.     

Capillary electrophoresis-inductively coupled plasma-mass spectrometry: a report on technical principles and problem solutions, potential, and limitations of this technology as well as on examples of application

This paper summarizes some basic principles of capillary electrophoresis (CE), inductively coupled plasma-mass spectrometry (ICP-MS), and coupling of both devices. Especially the interfacing is described in detail. A special focus is drawn to various interface developments reported in literature and technical problems, i.e., requirements to the interface setup and respective solutions. Nowadays, typically sheath flow-based interfaces are used. The sheath flow fulfills two requirements of hyphenation, (i) the closing of the electrical circuit of CE and (ii) the feeding of the used nebulizer with an adequate flow rate. In the beginning of CE-ICP-MS coupling predominantly home-made interface-nebulizer constructions were developed and tested for various speciation problems. Now increasingly such laboratory-constructed interfaces are left. Mostly commercial nebulizers are employed being combined with commercially available tee or cross fittings to connect the CE capillary to the electrode, the additional sheath flow, and the nebulizer. Due to the low sample amounts and low flow rates from CE, such nebulizers are typically low-flow nebulizers like, e.g., the microconcentric nebulizer (MCN) and the direct injection nebulizer (DIN). However, there are also reports on couplings using standard Meinhard systems. Still the control and reduction of a siphoning sucting flow and sufficient detection limits are the major problems in hyphenating CE to ICP-MS. Different solutions are reported on these problems and summarized here. Finally numerous applications are reported. Mostly, applications are performed on speciation of selenium, arsenic, metallothionein isoforms, mercury, or cobalt.     

Determination of seven arsenic compounds in urine by HPLC-ICP-DRC-MS: a CDC population biomonitoring method

A robust analytical method has been developed and validated by use of high-performance liquid chromatography inductively coupled plasma mass spectrometry with Dynamic Reaction Cell? (DRC) technology that separates seven arsenic (As) species in human urine: arsenobetaine (AB), arsenocholine, trimethylarsine oxide (TMAO), arsenate (As(V)), arsenite (As(III)), monomethylarsonate, and dimethylarsinate. A polymeric anion-exchange (Hamilton PRP® X-100) column was used for separation of the species that were detected at m/z 75 by ICP-DRC-MS (PerkinElmer? SCIEX® ELAN DRCII?) using 10% hydrogen–90% argon as the DRC gas. The internal standard (As) is added postcolumn via an external injector with a sample loop. All analyte peaks were baseline-separated except AB and TMAO. Analytical method limits of detection for the various species ranged from 0.4 to 1.7 μg L^?1 as elemental As. As(III) conversion to As(V) was avoided by adjusting the urine sample to 相似文献   

Comparison of several spray chambers operating at very low liquid flow rates in inductively coupled plasma atomic emission spectrometry

Four different spray chambers were evaluated in ICP-AES at very low liquid flow rates: a double-pass (Scott type), a conventional cyclonic, and two low-volume cyclonic-type spray chambers (i.e., Cinnabar and Genie). A glass concentric pneumatic micro nebulizer (Atom Mist) was used in conjunction with all four chambers. The liquid flow rate was varied from 10 to 160 microL min(-1). The conventional cyclonic spray chamber gave rise to coarser tertiary aerosols, higher analyte and solvent transport rates, higher sensitivity and lower limits of detection than the remaining ones. The low-volume spray chambers afforded analytical figures of merit similar to the double-pass one, despite their very different designs. However, these spray chambers exhibited shorter wash-out times. The matrix effects were significant only for the double-pass. This fact allowed the analysis of reference samples by employing aqueous standards at a minimum level of sample consumption. The recoveries obtained for the cyclonic spray chambers and several certified samples were close to 100%, being always lower in the case of the double-pass spray chamber.     

Stability studies of arsenic, selenium, antimony and tellurium species in water, urine, fish and soil extracts using HPLC/ICP-MS

The stability of arsenic, selenium, antimony and tellurium species in water and urine (NIST SRM 2670n) as well as in extracts of fish and soil certified reference materials (DORM-2 and NIST SRM 2710) has been investigated. Stability studies were carried out with As(III), As(V), arsenobetaine, monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), phenylarsonic acid (PAA), Se(IV), Se(VI), selenomethionine, Sb(III), Sb(V) and Te(VI). Speciation analysis was performed by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Best storage of aqueous mixtures of the examined species was achieved at 3 degrees C whereas at -20 degrees C species transformation especially of selenomethionine and Sb(V) took place and a new selenium species appeared within a period of 30 days. Losses and species transformations during extraction processes were investigated. Extraction of the spiked fish material with methanol/water led to partial conversion of Sb(III), Sb(V) and selenomethionine to two new antimony and one new selenium species. The other arsenic, selenium and tellurium species were almost quantitatively extracted. For soil spiked with MMA, PAA, Se(IV) and Sb(III), recoveries after extraction with water and sulfuric acid (0.01 mol/L) were below 20%.     

Determination of arsenic species by inductively coupled plasma mass spectrometry with ion chromatography

Five arsenic species, trimethylarsine oxide, dimethylarsenic acid, monomethylarsonic acid, arsenobetaine and sodium arsenite, in urine were analysed by inductively coupled plasma mass spectrometry with ion chromatography (IC ICP MS). Since the toxicities of different arsenic compounds are different, speciation of arsenic compounds is very important in the investigation of metabolisms. In this paper, we applied ion chromatography (IC) as a separation device and inductively coupled plasma mass spectrometry (ICP MS) as a detection device. For separation of the five arsenic compounds, an anion-exchange column and, as mobile phase, tartaric acid were used. The eluent from the IC column was introduced directly into the nebulizer of the ICP MS and analysed at 75 amu. Detection limits were from 4 to 9 pg as arsenic.     

Development of a low-flow multiplexed interface for capillary electrophoresis/electrospray ion trap mass spectrometry using sequential spray

A multiplexed CE-MS interface using four low-flow sheath liquid ESI sprayers has been developed. Because of the limited space between the low-flow sprayers and the entrance aperture of the ESI source, multichannel analysis is difficult using conventional rotating plate approaches. Instead, a multiplexed low-flow system was achieved by applying an ESI potential sequentially to the four low-flow sprayers, resulting in only one sprayer being sprayed at any given time. The synchronization of the scan event and the voltage relays was accomplished by using the data acquisition signal from the IT mass spectrometer. This synchronization resulted in the ESI voltage being sequentially applied to each of the four sprayers according to the corresponding scan event. With this design, a four-fold increase in analytical throughput was achieved. Because of the use of low-flow interfaces, this multiplexed system has superior sensitivity than a rotating plate design using conventional sheath liquid interfaces. The multiplexed design presented has the potential to be applied to other low-flow multiplexed systems, such as multiplexed capillary LC and multiplexed CEC.     

Effect of nebulizer/spray chamber interfaces on simultaneous,axial view inductively coupled plasma optical emission spectrometry for the direct determination of As and Se species separated by ion exchange high-performance liquid chromatography

Different nebulizer/expansion chamber combinations were evaluated to assess their performance for sample introduction in the direct coupling with an axial view inductively coupled plasma multielement spectrometer for on-line determination of As and Se species previously separated by ion exchange–high performance liquid chromatography. The column effluents were injected into the plasma without prior derivatization. The instrument operation software was adapted for data acquisition and processing to allow multi-wavelength recording of the transient chromatographic peaks. After optimization of the chromatographic operating conditions, separation of mixtures of inorganic As and Se species, and of inorganic and two organic As species (monomethylarsonic and dimethylarsinic acids), was achieved with excellent resolution. Species discrimination from mixtures of As and Se oxyanions was further improved by the simultaneous element detection at specific analytical wavelengths. Three nebulizers and three spray chambers, employed in seven combinations, were tested as interfaces. Concentric nebulizers associated to a glass cyclonic chamber appear most suitable regarding sensitivity and signal to noise ratio. Measured element detection limits (3 σ) were around 10 ng ml^− 1 for all the species considered, making the method a viable alternative to similar procedures that employ volatile hydride generation previous to sample injection into the plasma. Analytical recoveries both for inorganic and organic species ranged between 92 and 107%. The method was demonstrated to be apt for the analysis of surface waters potentially subjected to natural contamination with arsenic.     

Speciation of arsenic in chicken meat by anion-exchange liquid chromatography with inductively coupled plasma-mass spectrometry

A method was developed for speciation analysis of arsenic in chicken meat. Different procedures were optimized for the recovery of arsenic compounds without destroying the original compounds, and 2 anion-exchange liquid chromatography columns were compared for the separation of arsenic species prior to on-line detection by inductively coupled plasma-mass spectrometry. The 2 species found were dimethylarsinic acid (106 +/- 5 ng/g) and arsenobetaine (37 +/- 4 ng/g). The stability of arsenic species in a chicken meat candidate reference material for at least 12 months was demonstrated.     

Flow injection analysis with inductively coupled plasma-atomic emission spectroscopy: critical comparison of conventional pneumatic, ultrasonic and direct injection nebulization

The analytical figures of merit observed under flow injection analysis (FIA) conditions of a direct injection nebulizer (DIN) interfaced to an inductively coupled plasma-atomic emission spectroscopy (ICP-AES) facility were found to be comparable to or better than conventional pneumatic nebulization in terms of limits of detection, reproducibility and interelement effects. The DIN offered clog-free operation and part per billion limits of detection for 30μl sample injection volumes and carrier stream consumption rates in the range of 100–200μl min ⁻¹. The relative detection limits observed were generally comparable to those obtained for: (a) FIA introduction of 200μl or continuous sample introduction into a conventional cross flow nebulizer; and (b) FIA introduction of 500μl or continuous sample introduction into an ultrasonic nebulizer. Absolute and relative detection limits were comparable to or within the range of values reported for electrothermal vaporization-ICP-AES and comparable or superior to those reported for the graphite cup, direct insertion-ICP-AES. The reported absolute detection limits for the graphite-rod direct insertion approach ranged from comparable values to superior by a factor of 30. At the normal compromise observation height (20 mm), the interelement effects, to the extent they were observable, were comparable in magnitude for both the DIN and conventional cross-flow pneumatic nebulizer.     

Arsenic species analysis in freshwater using liquid chromatography combined to hydride generation atomic fluorescence spectrometry

A novel pretreatment system and method for arsenic species continuous analysis of arsenite, arsenate, monomethylarsenate (MMA) and dimethylarsonate (DMA) in freshwater using liquid chromatography combined to hydride generation atomic fluorescence spectrometry (LC-HG-AFS) was designed. Arsenic species of As(III), As(V), MMA and DMA in freshwater samples can be well separated, and the analytical time using the developed method is shortened twice compared to the conventional analytical procedure. Besides, the signal of As(V) can be increased by about 50% and the sensitivity to As(V) has been enhanced. The common coexisting ions in freshwater samples have no interferences with arsenic speciation analysis. A sensitive, low cost and interference-free procedure was developed and successfully applied to arsenic speciation in freshwater with the recoveries of four arsenic species within 89.2–106.2%. LC-HG-AFS has good prospects for speciation analysis of trace and ultra trace elements allowing for hydride generation.     

Speciation analysis of arsenic compounds in edible oil by ion chromatography-inductively coupled plasma mass spectrometry

An inductively coupled plasma mass spectrometer (ICP-MS) was used as an ion chromatographic (IC) detector for the speciation analysis of arsenic in edible oil. The arsenic species studied include arsenite, arsenate, monomethylarsonic acid, dimethylarsinic acid, arsenobetaine and arsenocholine. Gradient elution using (NH(4))(2)CO(3) and methanol at pH 8.5 allowed the chromatographic separation of all species in less than 8 min. Effluents from the IC column were delivered to the nebulizer of ICP-MS for the determination of arsenic. The concentrations of arsenic species have been determined in several used and fresh vegetable oil samples. In this study, a microwave-assisted extraction method was used for the extraction of arsenic species from oil samples. The extraction efficiency was better than 92% and the recoveries from spiked samples were in the range of 90-105%. The precision between sample replicates was better than 8% for all determinations. The limits of detection were in the range of 0.008-0.024 ng mL(-1) for various arsenic species based on peak height, which corresponded to 0.08-0.24 ng g(-1) in the original oil sample. The major arsenic species in the used oil samples varied based on the food items cooked.     

Comparison of several spray chambers operating at very low liquid flow rates in inductively coupled plasma atomic emission spectrometry

Four different spray chambers were evaluated in ICP-AES at very low liquid flow rates: a double-pass (Scott type), a conventional cyclonic, and two low-volume cyclonic-type spray chambers (i.e., Cinnabar and Genie). A glass concentric pneumatic micro nebulizer (Atom Mist) was used in conjunction with all four chambers. The liquid flow rate was varied from 10 to 160 μL min^–1. The conventional cyclonic spray chamber gave rise to coarser tertiary aerosols, higher analyte and solvent transport rates, higher sensitivity and lower limits of detection than the remaining ones. The low-volume spray chambers afforded analytical figures of merit similar to the double-pass one, despite their very different designs. However, these spray chambers exhibited shorter wash-out times. The matrix effects were significant only for the double-pass. This fact allowed the analysis of reference samples by employing aqueous standards at a minimum level of sample consumption. The recoveries obtained for the cyclonic spray chambers and several certified samples were close to 100%, being always lower in the case of the double-pass spray chamber.     

Use of a parallel path nebulizer for capillary-based microseparation techniques coupled with an inductively coupled plasma mass spectrometer for speciation measurements

A low flow, parallel path Mira Mist CE nebulizer designed for capillary electrophoresis (CE) was evaluated as a function of make-up solution flow rate, composition, and concentration, as well as the nebulizer gas flow rate. This research was conducted in support of a project related to the separation and quantification of cobalamin (vitamin B-12) species using microseparation techniques combined with inductively coupled plasma mass spectrometry (ICP-MS) detection. As such, Co signals were monitored during the nebulizer characterization process. Transient effects in the ICP were studied to evaluate the suitability of using gradients for microseparations and the benefit of using methanol for the make-up solution was demonstrated. Co signal response changed significantly as a function of changing methanol concentrations of the make-up solution and maximum signal enhancement was seen at 20% methanol with a 15 μl/min flow rate. Evaluation of the effect of changing the nebulizer gas flow rates showed that argon flows from 0.8 to 1.2 l/min were equally effective. The Mira Mist CE parallel path nebulizer was then evaluated for interfacing capillary microseparation techniques including capillary electrophoresis (CE) and micro high performance liquid chromatography (μHPLC) to inductively coupled plasma mass spectrometry (ICP-MS). A mixture of four cobalamin species standards (cyanocobalamin, hydroxocobalamin, methylcobalamin, and 5′ deoxyadenosylcobalamin) and the corrinoid analogue cobinamide dicyanide were successfully separated using both CE-ICP-MS and μHPLC-ICP-MS using the parallel path nebulizer with a make-up solution containing 20% methanol with a flow rate of 15 μl/min.     

Fast determination of arsenosugars in algal extracts by narrow bore high-performance liquid chromatography-inductively coupled plasma mass spectrometry

The potential of narrow bore high-performance liquid chromatography (HPLC) with detection by inductively coupled plasma mass spectrometry (ICP-MS) for fast determination of arsenosugars in algal extracts was explored. The retention behavior of four naturally occurring dimethylarsinoylribosides on an anion-exchange microbore column was investigated, with the mobile phase flow rate ranging from 60 to 200μLmin(-1). A low sample consumption system consisting of a micronebulizer and a low inner volume cyclonic spray chamber was used as the interface between the micro-column and the ICP mass spectrometer. Both the high efficiency nebulizer, HEN, and the PFA micronebulizer were tested, with the former providing 20-50% greater sensitivity than PFA (depending on the liquid flow rate), but comparable limits of detection and slightly lower chromatographic resolution. With the setup employed and under the optimal conditions, a satisfactory separation of the arsenosugars was achieved in less than 5min. The instrumental limit of detection was 0.20μgAsL(-1) and the precision was better than 3% (RSD%, n=5). The accuracy of the determination was verified by the analysis of a reference algal extract, obtaining values in good agreement with the reference ones.     

Metal speciation by means of microbore columns with direct-injection nebulization by inductively coupled plasma atomic emission spectroscopy

Ion chromatography can be used to perform speciation of several elements. This paper examines the use of ion chromatography with inductively coupled plasma atomic emission spectroscopy detection. A new type of nebulizer, the direct-injection nebulizer, was used to introduce the sample into the plasma. Columns were developed to interface with the direct-injection nebulizer at a flow-rate of 80–100 μl/min. The speciation of arsenic, selenium and chromium is discussed.     

Arsenic speciation: HPLC followed by ICP-MS or INAA

Sensitivities for the measurement of four arsenic species, As^III, As^V, monomethylarsonic acid (MMA) and dimethylarsinic acid (DMA), in environmental waters and rice extracts by a new neutron activation analysis (NAA) method using pre-separation of the species by liquid chromatography were determined. A manual fraction collection was used to isolate the species, followed by instrumental neutron activation analysis procedures. The sensitivities determined for arsenic species in the samples varied from 1.21 to 1.47 ng per vial or about 30 μg·L⁻¹ in sample solutions which translates to about 900 ng arsenic per gram of rice for our HPLC-NAA experiments.     

Separation and Detection of Arsenic and Selenium Species in Environmental Samples by HPLC-ICP-MS

A method is presented for arsenic speciation analysis of an oyster sample using ion chromatography coupled with an inductively coupled plasma mass spectrometry (ICP-MS) instrument. A strong anion exchange resin was employed with a step gradient elution of 0.1 mM/0.1 M K 2 SO 4 at pH 10.2. Arsenobetaine and dimethylarsinic acid were determined following extraction based on trypsin enzymolysis with 95-100% extraction efficiency. Limits of detection in the range 0.1-0.3 mg kg m 1 of arsenic were obtained for organic arsenic species. No inorganic arsenic was detected. Validation was performed using TORT-2 as a certified reference material. Although high performance liquid chromatography (HPLC) coupled to ICP-MS is an effective method for speciation analysis it is not always necessary to obtain such a detailed picture. A simple liquid chromatographic separation technique based upon mini-column technology is presented. It was developed to obtain a fast, efficient and reliable separation of inorganic from organic, i.e. assumed toxic from non-toxic, arsenic and selenium species suitable for use as an initial screening method for environmental analysis. Two types of strong anion exchange resin were tested. Excellent separation was obtained for both min-column resins and analysis times were within 7 min. Limits of detection obtained for inorganic arsenic, organic arsenic, selenomethionine, Se IV and Se VI were 1.6, 1.8, 66, 32 and 22 µg kg m 1 , respectively.