等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

煤的缔合结构研究Ⅱ溶液黏度变化

采用Pal-Rhodes方程描述了一种煤可溶组分PI-1溶液黏度随时间的变化关系,并计算得到了缔合物的缔合维数。25 ℃下PI-1在NMP和CS2/NMP混合溶剂中缔合物的缔合维数分别为2.08和2.19,表明其在低温下缔合属于反应控制机理。随着温度的提高,缔合维数趋于减小,表明在较高温度下,PI-1具有较快的缔合动力学过程,在50 ℃时PI-1在NMP中的缔合维数大于在CS2/NMP混合溶剂中的缔合维数,表明PI-1在NMP的缔合速率相对低于CS2/NMP混合溶剂。     

Study of ε-caprolactone polymerization by NIR spectroscopy

Near-infrared (NIR) spectroscopy is proposed for the in-line quantitative and kinetic study of the polymerization of ε-caprolactone and eventually to facilitate real-time control of the manufacturing process. Spectra were acquired with a fibre-optic probe operating in transflectance mode immersed in the reactor. The NIR data acquired were processed using a multivariate curve resolution alternating least squares (MCR-ALS) algorithm. The proposed method allows calculation of the concentration and spectral profiles of the species involved in the reaction. The key point of this method is the lack of reference concentrations needed to perform the MCR-ALS method. The use of an extended spectral matrix using both process and pure analyte spectra solves the rank deficiency. The concentration profiles obtained were used to calculate a kinetic fitting of the reaction, but the method was improved by applying kinetic constraints (hard modelling). The rate constants of batches at different temperatures and the energy of activation for this reaction were calculated. Whenever possible, the hard modelling combined with the MCR-ALS method improves the fit of the experimental data: the results show good correlation between the NIR and reference data and allow the collection of high-quality kinetic information on the reaction (rate constants and energy of activation).     

自由基引发的凝胶化反应的Monte Carlo模拟

基于自由基凝胶化反应的基本原理,在一个具有周期性边界条件的二维网络上,利用动态ＭｏｎｔｅＣａｒｌｏ 方法模拟了聚合物凝胶的自由基凝胶化反应,得到了凝胶的具体结构,研究了总单体浓度（ 单体浓度和交联剂浓度之和） 对凝胶的分形结构和孔径分布的影响．模拟中首次考虑了聚合后单体的运动对凝胶结构的影响．结果表明：考虑聚合后单体的运动,可使所得凝胶网络的分形维数和凝胶化所需的最低浓度均显著小于动力学凝胶化模型和ＤＬＡ 模型的相应值．用移动气泡法得到了凝胶网络的孔径分布,发现凝胶网络中大孔所占百分率明显多于随机纤维网络模型．     

Phase-field modeling of two-dimensional solute precipitation∕dissolution: solid fingers and diffusion-limited precipitation

Two-dimensional dendritic growth due to solute precipitation was simulated using a phase-field model reported earlier [Z. Xu and P. Meakin, J. Chem. Phys. 129, 014705 (2008)]. It was shown that diffusion-limited precipitation due to the chemical reaction at the solid-liquid interface has similarities with diffusion-limited aggregation (DLA). The diffusion-limited precipitation is attained by setting the chemical reaction rate much larger compared to the solute diffusion to eliminate the effect of the interface growth kinetics. The phase-field simulation results were in reasonable agreement with the analytical solutions. The fractal solid fingers can be formed in the diffusion-limited precipitation and have a fractal dimension measured d(f)=1.68, close to 1.64, the fractal dimensionality of large square lattice DLA clusters.     

New strategy to identify radicals in a time evolving EPR data set by multivariate curve resolution-alternating least squares

Electron paramagnetic resonance (EPR) spectroscopy is a powerful technique that is able to characterize radicals formed in kinetic reactions. However, spectral characterization of individual chemical species is often limited or even unmanageable due to the severe kinetic and spectral overlap among species in kinetic processes. Therefore, we applied, for the first time, multivariate curve resolution-alternating least squares (MCR-ALS) method to EPR time evolving data sets to model and characterize the different constituents in a kinetic reaction. Here we demonstrate the advantage of multivariate analysis in the investigation of radicals formed along the kinetic process of hydroxycoumarin in alkaline medium. Multiset analysis of several EPR-monitored kinetic experiments performed in different conditions revealed the individual paramagnetic centres as well as their kinetic profiles. The results obtained by MCR-ALS method demonstrate its prominent potential in analysis of EPR time evolved spectra.     

Extent-based kinetic identification using spectroscopic measurements and multivariate calibration

Extent-based kinetic identification is a kinetic modeling technique that uses concentration measurements to compute extents and identify reaction kinetics by the integral method of parameter estimation. This article considers the case where spectroscopic data are used together with a calibration model to predict concentrations. The calibration set is assumed to be constructed from reacting data that include pairs of concentration and spectral data. Alternatively, one can use the concentration- and spectral contributions of the reactions and mass transfers, which are obtained by pretreatment in reaction- and mass-transfer-variant form. The extent-based kinetic identification using concentrations predicted from spectroscopic data is illustrated through the simulation of both a homogeneous and a gas–liquid reaction system.     

分形表面上CO氧化反应的蒙特卡罗模拟

众所周知,人们在理想完好的单晶表面上的动力学研究已取得了很大的成功[1],然而对许多实际催化剂来说,传统催化理论和实验之间不符的情况仍然俯拾皆是．现在人们对造成这种情况的原因已经有了更加深入的认识：大量的实验事实表明,在表面催化反应体系中,不但催化剂表面具有复杂的分形结构,而且催化剂表面上的活性中心分布也具有复杂的分形特性[2]．“分形”是指那些具有分数维数的几何对象．这些对象往往是不规则的,不能用通常的欧氏几何来描述[3]．将分形引入催化科学中最早的是Pfeifer和Avnir等[4]人,至今已有近二十年的历史,现…     

Multi-component kinetic-spectrophotometric analysis. Selection of wavelength and time ranges

An empirical method for the selection of the best wavelength and time ranges which can be used in the quantification of binary mixtures, in a kinetic-spectrophotometric system, is proposed. It is based on finding those ranges which provide the least correlation between the kinetic profiles and the spectra of the products of reaction. The method was applied to the analysis of binary mixtures using simulated data with different rate constant ratios and in the presence of an interference that shows spectral overlap with the analytes. Subsequently, the proposed method was applied to the resolution of dyphylline and proxyphylline mixtures. The system studied was characterized by an elevated similarity in the kinetic behavior of the analytes under pseudo-first-order conditions and an elevated degree of spectral overlap of the products of reaction. In spite of this, satisfactory results were obtained in the quantification of the two analytes. The standard error of prediction (SEP) and the standard deviation between replicates (SDBR) did not show significant differences, being of the order of 4 and of 3% for dyphylline and proxyphylline, respectively.     

Simulation of diffusion-limited aggregation and reactions over its surfaces

Modifications of Witten–Sander diffusion-limited aggregation (DLA ) were proposed. Effects caused by releasing boundary shape, nonfixed seed, and rotating biased drift on the morphology of the resulting DLA were examined. The diffusion-limited reaction on surfaces of DLA were also studied by performing a multifractal scaling analysis. © 1994 John Wiley & Sons, Inc.     

Extraction of the contribution of kinetic profile for reaction of a chemical species in unknown matrices by standard addition method

A new and simple strategy is applied to resolve kinetic profile for the reaction of an analyte in unknown matrices, using standard addition method (SAM). The proposed method uses kinetic spectrophotometric data obtained by standard addition of analyte into unknown mixtures followed by the reaction of analyte with a proper reagent. The proposed method extracts kinetic profile for the reaction of an analyte by averaging the kinetic profiles obtained by subtraction of kinetic profiles after and before standard addition. The rate constant can be obtained using computational curve fitting. The performance of method was evaluated by using synthetic data as well as several experimental data sets. The proposed method can be applied to obtain kinetic profiles of the reactions in the presence of additive interference as well as multiplicative interferences. Hydroxylation reaction of diphenylcarbazide (DPCI) in the presence of diphenylcarbazone (DPCO) as a real system at various pHs was also studied by the present method. The rate constant and the order of the hydroxylation reaction were determined from extracted kinetic profiles.