CaO-MgO-Fe2O3-Al2O3-SiO2玻璃晶化机理

玻璃晶化动力学对于理解玻璃的稳定性和制备微晶玻璃十分重要．目前，通过DTA或DSC等简单技术去研究非等温过程和等温过程的动力学已取得一定的进展[1]．这些方法虽然方便，但需要事先知道晶化机理或借助XRD等技术确定Avrami参数[2]才能得到活化能．根据动力学理论，晶体生长速度与晶体生长活化能尽有直接关系[3]，通过理论计算晶体生长速度（U）可以确定玻璃体系的活化能，再结合DTA技术和Kissinger修正方程就可能确定晶体生长机理，这方面研究还未见报导．CaO－MgO－Fe2O3－AI2O3－SiO2（CMFAS）是本文综合利用废渣和尾矿制…     

静态水热晶化法高效合成MCM-22分子筛

 采用静态水热晶化法，在Na2O－Al2O3－SiO2－HMI－H2O（HMI：六亚甲基亚胺）体系中，在HMI／SiO2摩尔比为0．09，H2O／SiO2摩尔比为12，晶化时间为60～80h的条件下，合成了MCM－22分子筛．利用固体硅胶表面的吸附性能提高模板剂的局部浓度，从而实现了分子筛的高效合成．对合成条件的研究结果表明，以比表面积（486m2／g）大、反应性能好的硅胶为硅源是静态水热晶化法高效合成MCM－22分子筛的关键，而成胶老化方式对MCM－22分子筛的晶化影响不大．产物的晶相和转晶的类型取决于合成凝胶的初始硅铝比．当SiO2／Al2O3摩尔比＝18～80时可以合成出MCM－22，当SiO2／Al2O3＝13～17时可以合成出MCM－49．硅铝比较低（如SiO2／Al2O3＝20）时，MCM－22分子筛易转晶为MOR分子筛，而在硅铝比较高（如SiO2／Al2O3＝50）时，可转晶为ZSM－5分子筛．     

B2O3/TiO2-ZrO2催化环己酮肟气相Beckmann重排反应研究 Ⅰ.B2O3含量的影响

 制备了不同B2O3含量（0～20％）的B2O3／TiO2－ZrO2固体酸催\r\n化剂，用XRD，FT－IR，N2吸附及NH3－TPD等方法测定了其结构、比表\r\n面积、孔分布和表面酸性．结果表明，当B2O3含量较低（≤5％）时，\r\n催化剂呈无定形态，样品中的B2O3主要以BO4结构存在．当B2O3含量较\r\n高（≥8％）时，催化剂中的TiO2－ZrO2以ZrTiO4晶相存在，分散于Ti\r\nO2－ZrO2表面的B2O3主要以玻璃体形式和BO3结构存在．随着B2O3含量\r\n的增加，催化剂的比表面积减小，孔径增大．300℃下的环己酮肟气相\r\nBeck－mann重排反应结果表明，随着B2O3含量的增加，己内酰胺的选择\r\n性逐渐增大，而己内酰胺的收率在B2O3含量为12％时达到最大值．讨论\r\n了B2O3／TiO2－ZrO2的催化性能与其表面酸性及孔径大小的关系．     

二乙炔桥连苯并菲盘状液晶二聚体的合成及其介晶性

通过桥链将2个盘状介晶基元相连,不仅可以稳定盘状液晶柱状相,还有利于玻璃态柱状相的形成,提高盘状液晶作为有机半导体材料的实用性．为此,通过铜盐催化的Eglinton偶联反应合成了8个二乙炔桥连的苯并菲盘状液晶二聚体化合物[C18H6（OCnH2n＋1）4（OMe）O2C—C8H16-C--C-]2,3（n）,（n=4-8）,[C18H6（OC6H13）5O2C—C8H16-C-C-]2,（6）和[C18H6（oc6H13）5O-（CH2）m-C-=C-]2,8（m）,（m=1,3）．差示扫描量热法（DSC）和热台偏光显微镜（POM）对其介晶性进行研究发现：（1）苯并菲周边柔链长度对液晶二聚体化合物的介品性有影响;（2）二聚体化合物3（n）和6具有玻璃态柱状相,并且所有苯并菲二聚体化合物在降温至-50℃均未出现结晶现象;（3）与二聚体3（6）相比,分子对称性较高的化合物6具有较稳定的柱状相,及较宽的介晶温度范围;（4）连接基、中心桥链的长度和刚性对苯并菲盘状液晶二聚体介晶性有重要影响．     

铒硼硅酸盐稀土玻璃的析晶行为

高含量稀土玻璃在激光防护材料方面具有重要的应用,通过对稀土玻璃析品行为的研究.有助于制备出透明的高稀土含量稀土玻璃.分别制备了透明的铒硼硅酸盐稀土玻璃和富B2O3、富SiO2、富Al2O3的铒硼硅酸盐稀土玻璃,并在1100℃下对各种玻璃样品进行热处理.采用XRD,SEM等分析测试方法对Er2O3-B2O3-SiO2-Al2O3系玻璃的析晶行为进行研究,并探讨了玻璃组成对析晶产物的影响.结果表明,铒硼硅酸盐稀土玻璃的局部结构与ErBO3晶相的结构具有一定的相似性;富B2O3,富SiO2、富Al2O3的铒硼硅酸盐稀土玻璃会发生失透现象.稀土玻璃发生失透是由玻璃析晶引起的,其中铒硼硅酸盐稀土玻璃中最易析出的晶相是ErBO3.     

Na2O-SiO2-Al2O3-NaCl-H2O体系中ANA和SOD沸石膜的水热合成

Na2O-SiO2-Al2O3-NaCl-H2O体系中，以水玻璃和准一水软铝石为原料，分别在 堇青石和玻璃载体上水热合成方沸石（ANA）和方钠石（SOD）沸石膜。研究水含量 、反应温度、反应时间与多次合成对膜结晶的影响。用XRD，SEM，EDX表征膜的晶 相、形貌和化学组成。堇青石负载方沸石膜在对95％（wt.)乙醇水溶液的渗透蒸发 实验中，水优先透过沸石膜的选择性显示了晶间孔的醇／水分离作用。非计量的 NaCl进入到在玻璃载体上成膜的方钠石笼中，致使该膜显示光致变色效应。     

BaFeO3和BaCeO3钙钛矿型氧化物的储氮性能

 采用改进的溶胶－凝胶法制备了Ba－Fe－O（Ba／Fe原子比为0．5），Ba－Ce－O（Ba／Ce原子比为1）和Ba－Sn－O（Ba／Sn原子比为1）氧化物，并考察了其储氮性能．结果表明，750℃焙烧的Ba－Fe－O样品，在400℃下的NOx储存容量（NSC）最大，其次为900℃焙烧的Ba－Ce－O样品；相同温度焙烧的样品，在400℃下的NSC均大于200℃下的NSC．XRD测试结果表明，750℃焙烧的Ba－Fe－O样品的缺陷钙钛矿BaFeO3－δ可能是储存NOx的主要活性相，而Ba－Ce－O和Ba－Sn－O样品储存NOx的活性相分别为钙钛矿型BaCeO3和BaSnO3．BET测定结果表明，样品的比表面积均较小．用FT－IR分析了Ba－Fe－O样品上储存的NOx物种．讨论了NSC大小与吸收温度、NOx吸收物种及样品物相之间的关系．     

SA耐火材料多晶结构与性能的研究

本实验采用磨具废砂和炉皮SiC废砂生产SA耐火材料，通过XRD分析和计算机处理确定各试样中的晶相（4H－SiC，33R－SiC，3C－SiC，α－Al2O3，β-石英和Al6Si2O13）及其各相的含量。通过材料性能与结构综合分析，确定较好的配方，其含量：磨具废砂50％，炉皮砂45％，结合剂5％，外加矿化剂2％。     

水热老化对含钯La0．9Sr0．1CoO3－δ／α－Al2O3催化性能的影响

 以浸渍法制备了α－Al2O3负载的含钯La0．9Sr0．1CoO3－δ钙钛矿样品，探讨了水热老化对样品催化CO－NO反应性能的影响，并以XRD，TPR和XPS等对样品在水热老化前后的结构进行了表征．结果表明，钯的引入方式直接影响样品的水热性能．掺钯样品（LaSrCoPd）具有良好的水热性能，经水热老化后，其催化活性显著提高，显示出最好的催化性能；样品中钯离子位于钙钛矿晶相内，形成α－Al2O3负载的La0．9Sr0．1Co0．95Pd0．05O3－δ．La0．9Sr0．1CoO3－δ／α－Al2O3负载钯的样品（Pd／LaSrCo）具有最高的初活性，但经水热老化后，其催化活性明显降低．在水热老化过程中，La0．9Sr0．1CoO3－δ钙钛矿的结构稳定，但含钯钙钛矿晶相中的钯离子迁移聚集成独立的PdO颗粒，较小的PdO颗粒聚集成较大的颗粒．水热老化后，Pd／LaSrCo样品表面裸露的钯原子数目减少，导致其催化活性降低；而LaSrCoPd样品表面裸露的钯原子数目增多，导致其催化活性升高．     

用醇还原VOPO4·2H2O制备的VOHPO4·0.5H2O的择优取向性能

 研究了用醇还原VOPO4·2H2O制备的VOHPO4·0．5H2O的晶面择优\r\n取向现象及其在正丁烷和空气混合气体中活化后,产物（VO）2P2O7的\r\n晶面择优暴露对正丁烷氧化制顺酐性能的影响．以伯醇还原VOPO4·2H\r\n2O制备的VOHPO4·0．5H2O晶体,晶面择优取向于（220）面,晶型为玫\r\n瑰状或扭曲的片状聚集体;活化后的产物仅含（VO）2P2O7相,其（02\r\n0）晶面择优暴露．以仲醇还原VOPO4·2H2O制备的VOHPO4·0．5H2O晶\r\n体,晶面择优取向于（001）面,晶型为平板片状体;活化后的产物由\r\n（VO）2P2O7,VOPO4和无定形相组成,其中（VO）2P2O7相含量低,其\r\n（020）晶面暴露少．由苄醇、环己醇和3－甲基－3庚醇还原VOPO4·2\r\nH2O制备的VOHPO4·0．5H2O的XRD谱与用仲醇制备的相似．用一般方法\r\n（V2O5／异丁醇／H3PO4）制备的VOHPO4·0．5H2O晶体不具有晶面择优\r\n取向性质,活化后得到的（VO）2P2O7的结晶度较低．由正辛醇还原VO\r\nPO4·2H2O制备的VOHPO4·0．5H2O经活化后,对正丁烷氧化制顺酐的催\r\n化性能优于用仲辛醇和一般方法制备的VOHPO4·0．5H2O．     

氧化钆对铁磷酸盐玻璃结构的影响

为探究Gd2O3含量对40Fe2O3-60P2O5(mol%)基础玻璃结构的影响,采用传统熔融-冷却法制备xGd2O3-(100-x)(40Fe2O3-60P2O5)(0≤x≤12mol%)系列玻璃。利用XRD、SEM、FTIR和Raman等手段对玻璃结构进行表征,并测试了玻璃密度和维氏硬度。结果表明,在Gd2O3含量小于等于4mol%时,易形成均质玻璃,在此范围内,玻璃密度和硬度都随Gd2O3含量的增加而增加,玻璃结构以焦磷酸盐结构为主,并伴随少量的正磷酸盐和偏磷酸盐结构。在磷酸盐玻璃结构中,Gd3+作为网络修饰离子,位于玻璃网络结构间隙。     

Sm3+掺杂CaO-SiO2-B2O3发光玻璃的制备、表征及性质

用高温固相法合制备了以CaO-SiO₂-B₂O₃为基质，Sm³⁺为激活离子的发光玻璃。对Sm³⁺的淬灭浓度、基质中的硼硅比例、其他稀土离子的敏化作用以及基质组成等因素对玻璃发光特性的影响进行了探讨，并用红外和X-衍射分析对样品的结构进行了表征。结果表明：当Sm^3＋掺杂的物质的量分数为1.2%,激发波长λ ＝ 404 nm时,玻璃体60CaO-20SiO₂-20B₂O₃∶1.2Sm^3＋的发光强度为4 838 A.U.( λ ＝ 606 nm );这种发光玻璃具有将紫外及近紫外光转换为橙红色光的特点。少量的Eu^3＋的掺入，对玻璃体的发光起敏化作用；玻璃体中的组分CaO可被ZnO替代。     

Preparation process and upconversion luminescence of Er3+-Doped glass ceramics containing Ba2LaF7 nanocrystals

The preparation process and upconversion luminescence of the Er(3+)-doped glass ceramics containing Ba(2)LaF(7) nanocrystals were investigated. The formation of Ba(2)LaF(7) nanocrystals in the glass ceramics was confirmed by X-ray diffraction. Er(3+)-doped glass ceramics containing Ba(2)LaF(7) nanocrystals exhibited highly efficient upconversion luminescence in comparison with glasses. With the increase of heat treatment temperature the upconversion luminescence intensity increased gradually. The composition of glasses was also found to have significant influence on the crystallization process of glass ceramics. The mixture of Ba(2)LaF(7) and La(2)O(3) nanocrystals and the mixture of La(2)F(3) and La(2)O(3) nanocrystals in the glass ceramics could be obtained by controlling different compositions of glasses. The upconversion luminescence intensity also varied significantly with different nanocrystals in the glass ceramics.     

Dynamics of lithium ions in calcium bismuthate glasses

Ion transport in Li(2)O-CaO-Bi(2)O(3) glasses has been studied in the frequency range from 10 Hz to 2 MHz and in the temperature range from 293 to 543 K. The variation of the dc conductivity and the activation energy of these glasses with composition have been compared with those of binary lithium bismuthate glasses. It has been observed that the introduction of CaO in small amount does not effect the dc conductivity and the corresponding activation energy, but the larger amount of CaO changes them to some extent. The frequency-dependent conductivity has been studied using both conductivity and modulus formalisms. The values of the nonexponential parameter and frequency exponent are found to differ for the Li(2)O-CaO-Bi(2)O(3) glasses from those for the binary Li(2)O-Bi(2)O(3) glasses. The concentration of mobile Li(+) ions does not change appreciably with the change in the Li(2)O as well as CaO content in the compositions. The increasing amount of CaO in the glass compositions for fixed Li(2)O content points out that CaO dilates the glass network, enhancing the migration of Li(+) ions.     

Effect of Ga2O3 on the spectroscopic properties of erbium-doped boro-bismuth glasses

The spectroscopic properties and thermal stability of Er3+-doped Bi2O3-B2O3-Ga2O3 glasses are investigated experimentally. The effect of Ga2O3 content on absorption spectra, the Judd-Ofelt parameters Omega t (t=2, 4, 6), fluorescence spectra and the lifetimes of Er3+:4I 13/2 level are also investigated, and the stimulated emission cross-section is calculated from McCumber theory. With the increasing of Ga2O3 content in the glass composition, the Omega t (t=2, 4, 6) parameters, fluorescence full width at half maximum (FWHM) and the 4I 13/2 lifetimes of Er3+ first increase, reach its maximum at Ga2O3=8 mol.%, and then decrease. The results show that Er3+-doped 50Bi2O3-42B2O3-8Ga2O3 glass has the broadest FWHM (81nm) and large stimulated emission cross-section (1.03 x1 0(-20)cm2) in these glass samples. Compared with other glass hosts, the gain bandwidth properties of Er+3-doped Bi2O3-B2O3-Ga2O3 glass is better than tellurite, silicate, phosphate and germante glasses. In addition, the lifetime of 4I 13/2 level of Er(3+) in bismuth-based glass, compared with those in other glasses, is relative low due to the high-phonon energy of the B-O bond, the large refractive index of the host and the existence of OH* in the glass. At the same time, the glass thermal stability is improved in which the substitution of Ga2O3 for B2O3 strengthens the network structure. The suitability of bismuth-based glass as a host for a Er3+-doped broadband amplifier and its advantages over other glass hosts are also discussed.     

The spectroscopic properties of Er(3+)-doped TeO(2)-Nb(2)O(5) glasses with high mechanical strength performance

(100-x)TeO(2)-xNb(2)O(5) (x=5-20) niobic tellurite glasses doped with 0.5 mol.% Er(2)O(3) were synthesized, and their thermal, mechanical, and spectroscopic properties were measured and compared to the properties of the typical 75TeO(2)-20ZnO-5Na(2)O (TZN) tellurite glass. The refractive index (n(d)), density (rho), and glass transition temperature (T(g)) of bulk glasses increase with the Nb(2)O(5) content. The Vickers microhardness (H(v)) of bulk glass in niobic tellurite glasses also increases with the Nb(2)O(5) content. The values (2.5-3.2GPa) of H(v) in the niobic tellurite glasses are 47-88% larger than that (1.7GPa) in TZN glass. The effect of Nb(2)O(5) content on absorption spectra, the Judd-Ofelt parameters Omega(t) (t=2, 4, 6), fluorescence spectra and the lifetimes of Er(3+):I(13/2) level were also investigated, and the stimulated emission cross-section was calculated from McCumber theory. With increasing Nb(2)O(5) content in the glass composition, the Omega(t) (t=2, 4, 6) parameters, fluorescence full width at half maximum (FWHM) of I(13/2) of Er(3+) increase, while the (4)I(13/2) lifetimes of Er(3+) decreases. Compared with TZN glass, the gain bandwidth properties of Er(3+)-doped TeO(2)-Nb(2)O(5) glass is much larger than in tellurite glass based TeO(2)-ZnO-Na(2)O system, bismush-based glass, germanate, and silicate glasses, which indicates that TeO(2)-Nb(2)O(5) glasses are better choice as a practical available host material for broadband Er(3+)-doped amplifier.     

Glasses in the CuNbOF<Subscript>5</Subscript>-BaF<Subscript>2</Subscript> and CuNbOF<Subscript>5</Subscript>-PbF<Subscript>2</Subscript> systems

Nonhygroscopic, colored glasses have been synthesized in the CuNbOF₅-BaF₂ and CuNbOF₅-PbF₂ systems proceeding from crystals of the complex compound CuNbOF₅ · 4H₂O. The glasses have been studied structurally and thermally. The crystallization resistance of the glasses has been studied as a function of glass composition. Lead difluoride glasses are more stable than barium difluoride glasses of the same composition. These glasses have lower glass-transition temperatures than the binary glasses formed in the NbO₂F-BaF₂ system. The glass structure is built of Nb(O,F)₆ polyhedra, which are linked in glass networks through oxygen bridges. Modifier cations influence both the structure of glass networks and the linkage of polyhedra.     

Nephelauxetic effect of low phonon antimony oxide glass in absorption and photoluminescence of rare-earth ions

An antimony oxide based monolithic glass with very high Sb2O3 content (70 mol%) in the system K2O-B2O3-Sb2O3 (KBS) has been prepared for the first time. Its phonon energy (602 cm(-1)), evaluated by infrared reflection spectroscopy, is found to be very close to that of fluoride glasses (500-600 cm(-1)). After doping with different rare-earth ions, their UV-vis absorption and photoluminescence properties have been explored, compared with those observed in other hosts and justified with quantitative calculation of nephelauxetic parameter and covalent bonding characteristics. It is been proposed that tunable laser or new color visible light sources may be obtained by controlling these fundamental properties of the glass host. The results also suggest that KBS glass may be used as hosts in the place of fluoride glasses. The Judd-Ofelt parameters, Ωt=2,4,6 for Nd3+, Ho3+, and Er3+ doped in KBS glass have been evaluated and compared with other glasses. It is established that Ωt=2 value follow a direct relationship with covalent character of the hosts which not only supports the above calculation but also provides a generalized evidence for the sensitivity of this parameter to their bonding characteristics.     

Structural, optical, physical and electrical properties of V2O5.SrO.B2O3 glasses

The present work aims to study the structure and variation of optical band gap, density and dc electrical conductivity in vanadium strontium borate glasses. The glass systems xV2O5.(40-x)SrO.60B2O3 and xV2O5.(60-x)B2O3.40SrO with x varying from 0 to 20 mol% were prepared by normal melt quench technique. Structural studies were made by recording IR transmission spectra. The fundamental absorption edge for all the glasses was analyzed in terms of the theory proposed by Davis and Mott. The position of absorption edge and hence the value of the optical band gap was found to depend on the semiconducting glass composition. The absorption in these glasses is believed to be associated with indirect transitions. The origin of Urbach energy is associated with the phonon-assisted indirect transitions. The change in both density and molar volume was discussed in terms of the structural modifications that take place in the glass matrix on addition of V2O5. dc conductivity of the glass systems is also reported. The change of conductivity and activation energy with composition indicates that the conduction process varies from ionic to polaronic one.     

Thermal and optical properties of Tm3+ doped tellurite glasses

Ultraviolet, visible (UV/VIS) and differential thermal analysis (DTA) measurements were carried out in order to investigate the optical and thermal properties of various 0.5 mol.% Tm2O3 containing (1 - x)TeO2 + xLiCl glasses in molar ratio. The samples were prepared by fusing the mixture of their respective reagent grade powders in a platinum cricuble at 750 degrees C for 30 min. DTA curves taken in the 23-600 degrees C temperature range with a heating rate of 10 degrees C/min reveal a change in the value of the glass transition temperature, Tg, while melting was not observed for the glasses containing LiCl content less than 50 mol.%. These glasses were found to be moisture-resistant. However, the glasses with LiCl content higher than 50 mol.%, in which a melting peak was observed at Tc = 401 degrees C, were moisture-sensitive. Absorption measurements in the UV/VIS region of the glasses without Tm2O3 content show that the Urbach cutoff occurs at about 320 nm and, is relatively independent of the LiCl content. Six absorption bands were observed in the Tm2O3 doped glasses corresponding to the absorption of the 1G4, 3F2, 3F3 and 3F4, 3H5 and 3H4 levels from the 3H6 ground level of Tm3+ ions. The spectra also show that the integrated absorption cross-section of each band depends on the glass composition. Judd-Ofelt theory was used to determine the Judd-Ofelt parameters as well as the radiative transition probabilities for the metastable levels of Tm3+ ions in (0.3)LiCl + (0.7) TeO2: 0.01 Tm2O3 glass which is moisture-resistant.