Luminescent phosphors, based on rare earth substituted oxyfluorides in the A(1)3−x A(2)xMO4F family with A(1)/A(2)=Sr, Ca, Ba and M=Al, Ga

A new family of UV-activated phosphors made by substituting rare-earth activators such as trivalent Eu, Tb, Tm and Er into A(1)_3−xA(2)_xMO₄F host lattices (A(1)/A(2)=Sr, Ca, Ba; M=Al, Ga) are introduced and their activation and emission spectra as well as their CIE values reported. The Tm-substituted system can be activated using light with a wavelength of 360 nm. Relative intensities of a family of Tb-substituted green phosphors activated at 254 nm and with emissions centered near 548 nm are discussed.     

机械合金化Fe100-xCux体系的X射线吸收精细结构研究

利用X射线吸收精细结构(XAFS)方法研究机械合金化制备的Fe_100-xCu_x(x=0,10,20,40,60,70,80,100,x为原子百分比)合金中Fe和Cu原子的局域环境结构.对于Fe_100-xCu_x(x≥40)二元混合物,球磨160h后,Fe原子的近邻配位结构从bcc转变为fcc,但Cu原子的近邻结构保持其fcc不变.与之相反,在Fe₈₀Cu₂₀和Fe₉₀Cu₁₀(x≤20)合金中,Fe原子的近邻配位保持其bcc结构而Cu原子的近邻配位结构从fcc转变为bcc结构.XAFS结果还表明,fcc结构的Fe_100-xCu_x样品中Fe的无序因子σ(0.0099nm)比bcc结构的Fe_100-xCu_x中的σ(0.0081nm)大得多;并且在机械合金化Fe_100-xCu_x(x≥40)样品中Fe原子的σ(0.0099nm)比其Cu原子的σ(0.0089nm)大.这表明机械合金化Fe_100-xCu_x样品中Fe和Cu原子可以有相同的局域结构环境但不是均匀的过饱和固溶体,而是由Fe富集区和Cu富集区组成的合金.我们提出互扩散和诱导相变机理来解释在球磨过程中Fe_100-xCu_x合金产生从bcc到fcc和从fcc到bcc变化的结构相变 关键词： XAFS 100-xCu_x合金')" href="#">Fe_100-xCu_x合金 机械合金化     

金属有机分解法制备的SrTiO3薄膜的光学特性

采用金属有机分解法（MOD）在石英衬底上沉积了SrTiO3薄膜。所制备的薄膜是晶格常数为a=b=c=3.90?的多晶结构。通过测量190—1100nm波段内的透射光谱，采用包络方法计算了薄膜的光学常数（折射率n和消光系数k）。结果表明，采用MOD方法制备的薄膜的折射率大于采用射频磁控溅射、溶胶—凝胶和化学气相沉积方法制备的薄膜的折射率；薄膜的折射率色散关系满足单振子模型，其中振子强度S0为0.88′1014m-2，振子能量E0为6.40eV；薄膜的禁带宽度为3.68eV。     

钙钛矿型纳米BaFeO3的制备、结构表征及铁磁性研究

采用溶胶-凝胶法制备出钙钛矿型纳米BaFeO₃粉末,利用X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)分析研究了其微观结构及形貌,结果表明：胶体试样经800℃退火处理后,形成了20nm左右的钙钛矿型BaFeO₃粉末,其(110)面晶面间距为0.280nm左右,(100)面晶面间距为0.401nm左右.利用振动样品磁强计(VSM)研究了纳米BaFeO₃粉末的室温铁磁性能,测量结果表明：在室温条件下,纳米BaFeO关键词： 溶胶-凝胶法 3')" href="#">钙钛矿型纳米BaFeO₃ 铁磁性 氧空位     

XAFS和XRD研究高能球磨对Fe70Cu30合金结构的影响

利用XRD和XAFS方法研究机械合金化Fe₇₀Cu₃₀二元金属合金随球磨时间的结构变化.XRD结果表明，球磨2 h后，部分金属Fe与Cu生成Fe-Cu合金；球磨20h后，金属Fe与Cu已完全合金化生成Fe-Cu合金，并只在2θ=44°处出现一个宽化的弱衍射峰，认为是在球磨20h后的Fe₇₀Cu₃₀合金中共存着fcc和bcc结构的Fe-Cu合金相.XAFS结果进一步表明，在球磨的初始阶段(2h)，fcc结构的Cu颗粒的晶 关键词： XAFS XRD 70Cu₃₀合金')" href="#">Fe₇₀Cu₃₀合金 机械合金化     

Synthesis and photoluminescence properties of Nd2O3 nanoparticles modified by sodium bis 2-ethylhexyl sulfosuccinate

This paper reports that Nd₂O₃ nanoparticles modified by AOT(sodium bis(2-ethylhexyl) sulfosuccinate) were prepared using microemulsion method in the system of water and propanol/AOT/toluene. Transmission electron microscopy shows that the Nd₂O₃ nanoparticles take the shape of sphere with 18\,nm and 31nm with different preparation. The organic sol of Nd₂O₃ nanoparticles is very stable at room temperature. X-ray diffraction results show that the product has hexagonal phase structure. Two ultraviolet emission band at 344\,nm and 361\,nm corresponding to the transition of ⁴D_3/2→4I_9/2 and 2P_3/2→⁴I₁₁₂ or ⁴D_3/2 →⁴I_13/2 were observed.     

VUV luminescence of Er<Superscript>3+</Superscript> ions in LiYF<Subscript>4</Subscript> and BaY<Subscript>2</Subscript>F<Subscript>8</Subscript> crystals

Vacuum ultraviolet luminescence of Er³⁺ ions in LiYF4 and BaY₂F₈ crystals has been investigated. It is revealed that under excitation by 193 nm radiation from an ArF excimer laser the interconfigurational 5d–4f radiative transitions in Er³⁺ ions are observed. It is shown that from the LiYF₄:Er crystal only the spin-forbidden luminescence (λ = 165 nm) is detected, whereas both the spin-forbidden (λ = 169 nm) and spin-allowed (λ = 160.5 nm) components are observed from the BaY₂F₈:Er crystal.     

氧流量对热蒸发CVD法生长β-Ga2O3纳米材料的结构及发光特性的影响

用热蒸发CVD法制备了β-Ga₂O₃纳米材料, 并用光致发光(PL)方法研究了其发光特性. Ｘ射线衍射分析显示, 产物为单斜结构的β-Ga₂O₃. 扫描电子显微镜测试表明: 在较小氧流量条件下制备的产物为β-Ga₂O₃纳米带, 宽度小于100nm, 长度有几微米; 较大氧流量时制备出β-Ga₂O₃纳米晶粒结构, 晶粒尺度在80—15 关键词： 光致发光 氧流量 纳米结构 2O₃')" href="#">Ga₂O₃     

Co:BaTiO3/Si(100)纳米复合薄膜制备、微结构及其紫外光电子能谱研究

采用脉冲激光气相沉积(PLD)方法,在Si(100)晶面上制备了Co:BaTiO₃纳米复合薄膜.采用X射线衍射(XRD)结合透射电镜(TEM)方法研究了两种厚度Co:BaTiO₃纳米复合薄膜的晶体结构,当薄膜厚度约为30 nm时,薄膜为单一择优取向;当薄膜厚度约为100nm时,薄膜呈多晶结构.原子力显微镜(AFM)分析表明,当膜厚为30nm时,薄膜呈现明显的方形晶粒.采用紫外光电子能谱(UPS)研究了Co的价态和Co:BaTiO₃纳米复合薄 关键词： 3')" href="#">BaTiO₃ 纳米复合薄膜 紫外光电子能谱     

Co:BaTiO3/Si(100)纳米复合薄膜制备、微结构及其紫外光电子能谱研究

采用脉冲激光气相沉积(PLD)方法，在Si(100)晶面上制备了Co:BaTiO₃纳米复合薄膜.采用X射线衍射(XRD)结合透射电镜(TEM)方法研究了两种厚度Co:BaTiO₃纳米复合薄膜的晶体结构，当薄膜厚度约为30 nm时，薄膜为单一择优取向；当薄膜厚度约为100nm时，薄膜呈多晶结构.原子力显微镜(AFM)分析表明，当膜厚为30nm时，薄膜呈现明显的方形晶粒.采用紫外光电子能谱(UPS)研究了Co的价态和Co:BaTiO₃纳米复合薄     

Ca2SiO4:Dy3+材料的制备及其发光特性

采用高温固相法制备了Ca₂SiO₄:Dy³⁺发光材料.在365nm紫外光激发下,测得Ca₂SiO₄:Dy³⁺材料的发射光谱为一多峰宽谱,主峰分别位于486nm,575nm和665nm处;监测575nm发射峰,测得材料的激发光谱为一多峰宽谱,主峰分别位于331nm,361nm,371nm,397nm,435nm,461nm和478nm处.研究了Dy³⁺掺杂浓度对Ca₂SiO₄:Dy³⁺材料发射光谱及发光强度的影响,结果显示,随Dy³⁺浓度的增大,黄、蓝发射峰强度比(Y/B)逐渐增大,利用Judd-Ofelt理论解释了其原因;随Dy³⁺浓度的增大,Ca₂SiO₄:Dy³⁺材料发光强度先增大,在Dy³⁺浓度为4 mol%时到达峰值,而后减小,根据Dexter理论其浓度猝灭机理为电偶极-电偶极相互作用.研究了电荷补偿剂Li⁺,Na⁺和K⁺对Ca₂SiO₄:Dy³⁺材料发射光谱的影响,结果显示,不同电荷补偿剂下,随电荷补偿剂掺杂浓度的增大,Ca₂SiO₄:Dy³⁺材料发射光谱强度的演化趋势相同,即Ca₂SiO₄:Dy³⁺材料发射峰强度先增大后减小,但不同电荷补偿剂下,材料发射峰强度最大处对应的补偿剂浓度不同,对应Li⁺,Na⁺和K⁺时,浓度分别为4mol%,4mol%和3mol%. 关键词： 白光LED 2SiO₄:Dy³⁺')" href="#">Ca₂SiO₄:Dy³⁺ 发光特性 电荷补偿     

Absorption Spectrum of Manganese Formate Dihydrate at Liquid Nitrogen Temperature

The absorption spectrum of manganese formate dihy-drate has been studied at liquid nitrogen temperature (80 K) in the region λ 650 nm to 300 nm. Three bands of the spectrum resolved themselves exhibiting fine structure. The splitting of the ⁴E_g (G) band is explained as due to exciton-magnon interaction. Weak bands on either side of ⁴A_1g (G) band are assigned to phonon progressions with = 0.12 kK. The fine structure of the ⁴T_2g (D) band is explained as due to spin-orbit interaction. The observed band positions are fitted to four parameters B, C, ηq and α the best fit being obtained with B = 0.82 kK; C = 3.02 kK; Dq = 0.81 kK; α = 0.076 kK.     

BH2和AlH2分子的结构及其解析势能函数

运用二次组态相关(QCISD)方法，分别选用6-311++G(3df,3pd)和D95(3df,3pd)基组，对BH₂和AlH₂分子的结构进行了优化计算，得到BH₂分子的稳态结构为C_2v构型，电子态为²A₁、平衡核间距R_BH=0.1187nm、键角∠HBH=128.791°、离解能D_e=3.65eV、基态振动频率ν₁(a₁)=1020.103cm^-1,ν₂(a₁)=2598.144cm^-1,ν₃(b₂)=2759.304cm^-1.AlH₂分子的稳态结构也为C_2v构型，电子态为²A₁、平衡核间距R_AlH=0.1592nm、键角∠HAlH=118.095°、离解能D_e=2.27eV、基态振动频率ν₁(a₁)=780.81cm^-1,ν₂(a₁)=1880.81cm^-1，ν₃(b₂)=1910.46cm^-1.采用多体项展式理论推导了基态BH₂和AlH₂分子的解析势能函数，其等值势能图准确再现了BH₂和AlH₂分子的结构特征及其势阱深度与位置.分析讨论势能面的静态特征时得到BH+H→BH₂反应中存在鞍点，活化能为150.204kJ/mol；AlH+H→AlH₂反应中也存在鞍点，活化能为54.8064kJ/mol. 关键词： 2')" href="#">BH₂ 2')" href="#">AlH₂ Murrell-Sorbie函数 多体项展式理论 解析势能函数     

AlO2和Al2O分子的结构与解析势能函数

运用密度泛函理论的B3LYP方法在6-311++G^**水平上,对AlO₂,Al₂O分子的结构进行了优化计算,得到AlO₂,Al₂O分子的稳定结构都为D_∞h构型.　AlO₂电子态为X²Π_u,平衡核间距R_Al-O关键词： 2')" href="#">AlO₂ 2O')" href="#">Al₂O Murrell-Sorbie函数 多体项展式理论     

Spectroscopy and Kinetics of HgBr (B-X) Formation Due to Collisions of Helium Ions with Methyl Mercury Bromide Molecules

Abstract

Emission resulting from collisions of 100–1000 eV He· and He₂· ions with CH₃HgBr molecules has been characterized in the 244–580 nm region. Emission bands due to HgBr (B-X), CH(A-X), and CH(B-X) transitions were observed besides atomic mercury lines. Emission cross-sections as a function of energy of helium ions for the strongest band of HgBr radical at 502 nm corresponding to the transition (v' = 0 ? v′ = 22) were determined.     

Absorption spectra of benzene-isooctane mixtures in the wavelength range 1620–1820 nm

Experimental absorption spectra of benzene, isooctane, and their mixtures are obtained in the wavelength range λ = 1620–1820 nm in which the first overtones of vibrational frequencies of CH, CH₂, and CH₃ hydrocarbon groups are located. Positions of fundamental absorption bands of benzene are refined. Absorption spectra of benzene-isooctane mixtures are shown to intersect in a narrow area near λ ≈ 1695 nm. The main maximum of benzene absorption at λ = 1671.5 ± 0.5 nm, where the influence of isooctane absorption is practically absent, is proposed for determining the content of benzene in benzene-isooctane mixtures. A linear calibration curve for λ = 1671.5 nm that encompasses the full range of benzene concentrations (0–100%) is presented. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 75, No. 5, pp. 631–634, September–October, 2008.     

垂直取向FePt/Ag纳米颗粒薄膜的结构和磁性

用磁控溅射法在单晶MgO(100)基片上制备了［FePt 2 nm/Ag dnm］₁₀多层膜， 经真空热处理后，得到具有高矫顽力的垂直取向L1₀-FePt/Ag颗粒膜.x射线衍射结 果表明，在250 ℃的热基片上溅射，当Ag层厚度d=3—11 nm时，FePt颗粒具有很好的［001］取向，随着Ag层厚度的增加，FePt颗粒尺寸减小.［FePt 2 nm/Ag 9 nm］₁₀经过6 00 ℃真空热处理15 min后，颗粒大小仅约8 nm，垂直矫顽力达到692 kA/m.这种无磁耦合作用的颗粒膜，适合用作超高密度的垂直磁记录介质. 关键词： 磁控溅射 垂直磁记录 纳米颗粒膜 0-FePt/Ag')" href="#">L1₀-FePt/Ag     

Cu掺杂对FexPt1－x薄膜有序化的影响

利用磁控溅射制备了薄膜厚度为50nm的系列(Fe_xPt_1-x)_100-yCu_y(x=0.46—0.56,y=0,0.04,0.12) 样品.利用直流共溅射方法精确控制Fe和Pt的原子比.实验结果表明，当x>0.52时，样品中添加Cu不能促进FePt的有序化，但是对于FePt化学原子定比或富Pt的样品，添加Cu可以促进FePt有序化，而且随着Fe含量的减少，需要更多的Cu添加才能实现较低温度下FePt薄膜的有序化.实验结果表明，原子比(FeCu)/Pt达到1.1—1.2的范围时，即可实现较低温度的有序化. 关键词： 0-FePt有序相')" href="#">L1₀-FePt有序相 磁控溅射 有序度 Cu掺杂     

Enhanced Photoelectrochemical Property of Zn Loaded TiO2 Nanotube Arrays Electrode

采用计时电流法制备了负载Zn纳米粒子的TiO₂纳米管阵列电极．通过阳极氧化法制备TiO₂纳米管阵列电极,然后通过控制计时电流沉积时间来控制负载在TiO₂纳米管上Zn纳米颗粒的沉积量和 沉积尺寸．SEM和XRD分析结果显示,沉积时间为3～5 s时,负载在TiO₂纳米管上的Zn粒子的直径为15～25 nm．UV漫反射光谱发现负载Zn的TiO₂纳米管阵列电极比没有负载的样品吸收487～780 nm的光更强;在高压汞灯照射下,前者比后者的光电流响应提高了50%．