乳液聚合法制备纳米金/聚苯乙烯复合粒子

以氯金酸为前驱体,十二烷基硫醇和硼氢化钠分别作为稳定剂和还原剂,采用相转移法制备了单分散的金纳米粒子.将金纳米粒子通过乳液聚合的方法制备了纳米金/聚苯乙烯复合粒子.通过紫外-可见吸收光谱(UV-Vis)研究了纳米金和纳米金/聚苯乙烯复合粒子的光吸收特性,使用傅立叶变换红外光谱(FT-IR)、X射线衍射(XRD)、透射电子显微镜(TEM)和动态光散射(DLS)对产物的组成、晶体结构、形貌、以及粒径进行了表征.结果表明,复合粒子为粒径分布较窄的球形,其中的金纳米粒子为面心立方结构.热失重分析(TGA)说明制备的纳米金/聚苯乙烯复合粒子具有很好的热稳定性.     

Fe3O4表面原位引发可控/“活性”聚合制备磁性聚苯乙烯纳米粒子

采用化学共沉淀方法合成了Fe3O4纳米粒子, 用3-甲基丙烯酰氧基丙基三甲氧基硅烷(3-MPS)对其进行表面接枝修饰, 然后以苯乙烯(St)为单体, 过氧化苯甲酰(BPO)为引发剂, 4-羟基-2,2,6,6-四甲基哌啶-1-氧化物自由基(HTEMPO·)为稳定自由基介质, 采用可控/“活性”自由基聚合技术在修饰后的Fe3O4纳米粒子表面原位引发聚合, 制备了粒径小、分布窄、磁含量高的磁性聚苯乙烯（PS）纳米粒子. X射线衍射(XRD)研究表明, 所合成的Fe3O4粒子为尖晶石结构. 凝胶渗透色谱(GPC)分析表明, 聚苯乙烯的分子量与反应时间呈较好的线性关系. 透射电镜(TEM)观察表明, 所制备的磁性聚苯乙烯纳米粒子的粒径在20-30 nm之间. 热重(TG)分析得到磁性聚苯乙烯纳米粒子的磁含量为62.6%. 振动样品磁强计(VSM)测试结果表明, 磁性聚苯乙烯纳米粒子的比饱和磁化强度为31.7 emu·g-1, 呈现单磁畴结构.     

静电层层自组装制备聚苯乙烯微球(核)/MCM-41纳米粒子(壳)阶层结构复合微粒

采用聚苯乙烯磺酸钠(PSS)和聚二烯丙基二甲基氯化铵(PDDA)两种聚电解质, 通过静电层层自组装成功地将MCM-41介孔二氧化硅纳米粒子包覆到聚苯乙烯(PS)微球表面. 实验结果表明, 当以尺寸为1.4 μm的PS微球为核时, 包覆了两个聚电解质双层(PDDA/PSS)2的PS(PDDA/PSS)2(PDDA/MCM-41)复合结构微粒与包覆了一个聚电解质双层(PDDA/PSS)的PS(PDDA/PSS)(PDDA/MCM-41)复合结构微粒相比, 复合结构微粒之间的交联程度降低, 但是MCM-41纳米粒子在聚苯乙烯微球表面的包覆都比较松散, 且产物中存在大量杂质. 而当以尺寸为5 μm的聚苯乙烯微球为核时, MCM-41纳米粒子紧密地包覆在聚苯乙烯微球表面, 复合结构微粒之间只有少量桥连物, 且产物中杂质很少.     

Pickering乳液聚合制备核-壳结构PS-SiO2复合微球

用二氯二甲基硅烷对纳米SiO2粒子进行疏水改性,当其表面Zeta电位由-54.8 mV变成-25.8 mV时,SiO2粒子就能在苯乙烯-水界面自组装,形成稳定的Pickering乳液,即以胶体粒子为乳化剂的乳液.利用Pickering乳液聚合制备了以聚苯乙烯(PS)为核、纳米SiO2为壳的PS-SiO2复合微球.用FT-IR、XPS、SEM、偏光显微镜等对复合微球进行了表征.结果表明:复合微球由聚苯乙烯和纳米二氧化硅粒子组成,二氧化硅粒子以单层、六方密排的方式分布在聚苯乙烯微球表面.     

用ATRP方法制备聚苯乙烯/纳米二氧化硅杂化粒子

采用过量的甲苯-2,4-二异氰酸酯(TDI)对SiO₂纳米粒子表面进行修饰, 将原子转移自由基聚合(ATRP)引发剂引入到SiO₂粒子表面合成大分子引发剂, 采用ATRP技术将聚苯乙烯(PS)大分子链接枝到SiO₂表面制备出以纳米二氧化硅为核, 聚苯乙烯为壳的PS/SiO₂杂化粒子. 利用红外光谱(FTIR)、核磁共振谱( NMR)、凝胶色谱(GPC)等实验手段对杂化粒子及表面接枝聚苯乙烯进行了表征分析.     

硫醇末端基聚合物对金纳米粒子配体置换

探讨了具有硫醇末端基的聚苯乙烯分子量对配体置换法制备聚合物接枝金纳米粒子的影响.通过可逆加成-断裂链转移(RAFT)聚合反应合成了一系列具有不同分子量的聚苯乙烯(PS),并以正丙胺为还原剂将双硫脂末端基还原成硫醇(—SH).通过用PS-SH配体置换将水相中金纳米粒子(Au NPs)转移至油相中,研究发现,PS分子量越大,进行配体置换得到单分散胶体粒子所需的PS-SH浓度越大.当PS-SH分子量达到59700时,即使增加溶液中PS-SH的浓度,仍无法在油相中得到单分散的稳定胶体粒子.     

苯乙烯在阴离子型聚氨酯纳米水分散液中聚合过程的研究

采用自乳化法制备出阴离子聚氨酯纳米水分散液,以其作为乳化剂使苯乙烯单体在其中进行聚合,制备出不同聚苯乙烯与聚氨酯质量比的阴离子型PS/PU纳米复合物水分散液;对苯乙烯单体的聚合过程进行了研究;采用光子相关谱仪和透射电镜对其微观结构、粒径及其分布进行了测试,结果表明,该方法能够制备出稳定的具有核壳结构的PS/PU纳米复合物水分散液,但当苯乙烯单体浓度增大到一定程度(PS/PU质量比为50∶100)时,粒子不稳定而发生聚集.     

Fe3O4/聚苯乙烯纳米复合材料的结构与性能

采用油酸(OA)表面改性的粒径均一的Fe3O4纳米粒子(OA-Fe3O4)与工业化聚苯乙烯(PS)通过溶液共混挥发干燥方法得到了具有超顺磁性的OA-Fe3O4/PS纳米复合材料.透射电子显微镜表征结果表明,在OA-Fe3O4质量分数为1%~10%时,OA-Fe3O4纳米粒子均匀分散在PS聚合物基体中.示差扫描量热分析表明,随着纳米粒子加入量的增加,纳米复合材料的玻璃化转变温度逐渐降低.热失重分析表明,OA-Fe3O4的存在显著提高了PS在空气条件下的热稳定性.流变分析表明,随着纳米粒子加入量的增加(0~10%),复合材料黏度逐渐降低.进一步研究了分子量双峰分布的PS与OA-Fe3O4纳米复合体系的流变行为,结果表明,当PS基体的平均分子量大于临界缠结分子量,且填充的纳米粒子的半径小于双峰分布PS的均方旋转半径时,加入纳米粒子仍然导致体系的复合黏度降低.     

纳米银碗阵列结构的高效制备及荧光增强性能

报道了一种以自组装单层聚苯乙烯纳米微球阵列为模板, 通过真空热蒸镀银纳米粒子高效制备大面积银碗阵列结构的方法. 测试结果表明, 制得的银碗阵列结构为微纳米复合分级结构, 银碗由平均粒径为10 nm的银纳米粒子组成. 紫外-可见吸收光谱测试结果表明, 银碗阵列结构表面具有银纳米粒子的局域表面等离子体共振吸收峰. 将荧光分子N,N'-二正丁基喹吖啶酮(DBQA)分别蒸镀到普通银膜和银碗阵列结构表面并测试了荧光光谱. 结果表明, 在银碗阵列结构表面的荧光分子强度得到了显著增强, 说明制备的银碗阵列结构是优良的荧光增强基底.     

核/壳纳米复合粒子填充聚苯乙烯的流变行为

采用细乳液聚合制备了以偶联剂改性纳米二氧化硅粒子(SiO2)为核、交联聚苯乙烯(PS)为壳的SiO2@PS复合纳米粒子(SCCSN).采用透射电子显微镜(TEM)、动态光散射(DIS)法考察了SCCSN的粒子形貌特征,发现SCCSN呈球形,粒径约90 nm,均匀分散;采用热失重(TG)、调制式差示扫描量热(MDSC)与动态力学分析(DMA)研究了SCCSN的结构特征,发现PS包覆率随交联剂含量增加而升高,且玻璃化转变温度(Tg)显著升高.交联壳层不仅能够将聚合物锚固在SiO2表面,屏蔽SiO2粒子与基体PS间相互作用,而且阻止PS壳层与基体PS分子链间的缠结.MDSC结果显示,SiO2与SCCSN填充可降低复合物Tg.动态流变结果表明,填充PS熔体非线性流变行为与PS分子链解缠结有关,SiO2与SCCSN均不影响填充熔体非线性流变机理.SCCSN的SiO2核对PS的增强效应略优于SiO2,且增强效应与壳层交联度有关.     

Modification of PP by blending with PS and reactive polymers

In this paper a polypropylene (PP) resin with controlled rheology was selected as polymer matrix and modified by melt mixing with polystyrene (PS) which has certain processing compatibility with PP. The effect of the addition of polyperoxide (PPX), peroxide modified PS particles (PS‐PPX), and maleic anhydride (MAH) to the PP/PS blend during melt mixing on the rheological behavior and morphology of the PP/PS blends has been carefully studied.     

The heat capacity of solid poly(p-xylylene) and polystyrene

The constant-pressure heat capacity C_p of poly(p-xylylene) (PPX) has been measured from 220 to 625 K by differential scanning calorimetry. The constant-volume heat capacities C_v of both, PPX and its isomer polystyrene (PS) have been interpreted in the light of literature data on full normal-mode calculations for PS and estimates from low-molecular-weight analogs for PPX for the 39 group vibrations. Nine skeletal vibrations were used in this discussion with characteristic temperatures θ₁ and θ₃ of 534.5 and 43.1 K for PS. It was also possible to calculate a heat capacity contribution of a phenylene group within a polymer chain. Single 48-vibration θ₁ temperatures of 3230 K for PS and 2960 K for PPX are sufficient to describe C_v above 220 K. Below 140 K, PS heat capacity shows deviations from the Tarasov treatment.     

The influence of nano‐PS particle on structure evolution and electrical properties of PP/PS

The polypropylene‐g‐polystyrene (PP‐g‐PS) copolymers with different grafting ratios are used as compatibilizers to control the size of polystyrene (PS) particles at nanometer scale in polypropylene (PP) matrix. Then the PP/PS insulating nanocomposites (containing 10 wt % PS calculated from PS and PP‐g‐PS) are manufactured. With the increase in grafting ratio of PP‐g‐PS, the size of PS particle is reduced and the interfacial adhesion is enhanced. Meanwhile, the dielectric properties, DC breakdown strength and volume resistivity are increased with the decreasing of PS particle size. The spherulite size of PP is decreased and the boundary between crystals and amorphous regions is blurred or even disappears due to the presence of PS nanoparticles. This evolution of PP structure is attributed to the serious entanglements of PP and PS molecular chains. Finally, the correlation between morphological structure and electrical properties is ultimately established based on the in‐depth understanding of the molecular chain movement, crystal structure, and phase morphology. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 706–717     

NETWORK ENCAPSULATION OF NANOMETER CaCO_3

The encapsulation of stearic acid coated nanometer CaCO3 by a polystyrene (PS) network via emulsion polymerization is described, where γ-methacryloxypropyltrimethoxysilane (MPS) was used as an efficient crosslinker. The important factors such as the type and amount of surfactant and initiator and the content of CaCO3 are investigated as well as the role of MPS. It has been shown that little PS was extractable with only 0.6 wt% of MPS (relative to styrene). The cationic surfactant cetyl trimethylammonium bromide (CTAB) proved more effective than the anionic surfactant sodium dodecyl sulfonate (SDS). The yield rises, particles become smaller and size distribution broadens with increased amount of CTAB. It is also found that either 2,2′-azobis(isobutyronitrile) (AIBN) or ammonium persulfate (APS) is suitable for attaining high monomer conversion. With increased amount of CaCO3, the encapsulation ratio can be varied from 17.9 to 3.6, while monomer conversion and yield decrease slightly. FT-IR spectra of the products after extraction indicate tight encapsulation between PS and CaCO3, and TEM photographs of composite particles with well-defined core-shell structure give direct evidence of encapsulation.     

St/交联剂乳液共聚包覆硬脂酸改性碳酸钙颗粒的研究

在硬脂酸改性的纳米碳酸钙存在下,通过苯乙烯(St)与多乙烯基单体的乳液共聚合,制备了以纳米碳酸钙为核,以交联聚苯乙烯(PS)为壳的交联型PS/碳酸钙复合纳米粒子.研究了多乙烯基单体的种类和用量以及碳酸钙的用量对聚合反应以及包覆的影响.结果表明,多乙烯基单体以及碳酸钙的引入会使聚合反应速率有不同程度的降低;使用1%~5%的TMPTMA或DVB,可实现PS对碳酸钙颗粒的牢固包覆,不可抽提的PS达94%以上;当碳酸钙用量改变时,需要适当调整乳化剂和多乙烯基单体的用量;IR和TGA的结果表明,随着碳酸钙用量增加,产物中的碳酸钙含量也相应增加;TEM照片和计算结果显示,当碳酸钙用量为14.8%时,绝大部分碳酸钙颗粒被包覆,且基本上每个乳胶粒中包覆一个碳酸钙颗粒,复合粒子具有清晰的核壳结构,壳层厚度约为10 nm,而当碳酸钙用量增加到29.3%和58.7%时,壳层厚度减小,并且出现较多裸露的碳酸钙颗粒.     

量子化尺寸纳米颗粒及其在生物体系中的作用

本文从胶体化学与物理化学的角度介绍了纳米颗粒的尺寸量子化效应。介绍了作者所进行的纳米颗粒在生物体系中的应用工作。纳米颗粒金和二氧化硅能显著地提高葡萄糖氧化酶的生物活性。纳米颗粒金能提高视黄醛仿生膜的光电响应电流和寿命。作者用纳米颗粒的吸附浓集效应、吸附定向效应、和量子尺寸效应来解释这些效应     

硫化锌纳米粒子的乳液合成

纳米材料被人们认为是新型的功能材料^[1]。作为过渡金属硫化物,硫化锌（ZnS)材料显示出许多特异光电性能,在许多领域有着广泛的应用^[2],因而一直被应用和研究。     

Ag-TiO2纳米催化剂的制备、表征及环氧化催化性能

环氧化合物是一类重要的有机合成中间体。工业上环氧乙烷是以Ａｇ ＳｒＯ ＣａＯ作催化剂 ,通过多相催化由乙烯和氧气氧化得到 ,其它的Ｃ2以上烯烃不能用该法生产 ,因为反应温度高 ,选择性很差。高温下的银催化乙烯的分子氧环氧化 ,选择性高于 80 % ,而用于丙烯的环氧化时 ,选择性大大降低[1] ,银多相催化分子氧环氧化烯烃的研究较活跃[2 5] 。本文合成了Ａｇ ＴｉＯ2 纳米催化剂 ,对其进行了表征 ,并初步研究了其环氧化催化性能。1　实验部分1 .1　仪器药品ＴｅｓｔｓｃａｎＳｈｉｍａｄｚｕＦＴＩＲ 80 0 0ｓｅｒｉｅｓ红外光谱仪 (ＫＢ…     

Probing molecules adsorbed at the surface of nanometer colloidal particles by optical second-harmonic generation

It is observed that optical second-harmonic generation from molecules adsorbed at the surface of nanometer size colloidal particles occurs at angles as large as 90 degrees away from the fundamental beam direction. This phenomenon can be rigorously described by the nonlinear Rayleigh-Gans-Debye theory and used for probing molecules adsorbed on nanometer size colloidal particles.     

Production of micron-sized polystyrene particles containing PEG near the particles surface

Polystyrene (PS) particles in the size range of 1-7 µm, containing poly(ethylene glycol) or PEG on the particles surface, were prepared by multi-step seeded polymerizations. Micron-sized PS particles were first prepared by dispersion polymerization using 2,2'-azobisisobutyronitrile as initiator and polyvinyl pyrrolidone as stabilizer. Conventional swelling method was then used to increase the size of the PS particles with a large amount of styrene in presence of oil soluble initiator, benzoyl peroxide. In the final step, the PS particles have been used to carry out seeded polymerization with small amount of styrene in presence of poly(ethylene glycol)-azo or PEGA initiator with average molecular weights of the PEG chains of 200 and 3000 g mol^-1 , respectively. The average size, size distribution, and surface morphology indicate that seeded polymerization in the final step with small amount of styrene in presence of PEGA is the best way to produce monodisperse polystyrene particles containing PEG near the particles surface.