A heated electrospray source for mass spectrometry of analytes from aqueous solutions

An electrospray interface is described that provides high sensitivity and signal stability for mass spectrometric detection of analytes in solvents with high water content including 100% water. The electrospray capillary tip section is heated close to the boiling point of the solvent. An approximately 20°C hotter airstream, with flow coaxial to the electrospray tip and codirectional to the electrospray.. is also used. With this arrangement, the analyte signal sensitivity and stability obtained with neat water is equal to that obtained with neat methanol. The heated electrospray also affords the use of a wide range of flow rates: 1–100 μL/min.     

Organotin speciation in textile and plastics by microwave-assisted extraction HPLC-ESI-MS

The HPLC coupled with electrospray ionization mass spectrometry (ESI-MS) was applied for the determination of tributyltin chloride (TBT), triphenyltin chloride (TPhT), triethyltin chloride (TET) in textile and plastic samples. The separation was performed in the isocratic mode on ion exchange SCX column with a mobile phase containing methanol-ammonium acetate (50 mmol l(-1))-acetic acid (90/9.98/0.02, v/v/v). Sensitive detection of three organotin compounds by ESI-MS was performed on the basis of multiple reaction monitoring (MRM) mode. Limits of detection were 0.4, 20, 4 ng ml(-1) for TBT, TPhT, and TET, respectively. Microwave-assisted extraction (MAE) of organotin compounds was finished in 60% (v/v) methanol aqueous solution. Under the experimental conditions used, recoveries of three organotin compounds obtained for spiked textile and plastic samples are in the range of 55-95% and the R.S.D.s are 3-9%.     

A liquid chromatography-mass spectrometric method for the determination of oak moss allergens atranol and chloroatranol in perfumes

This paper describes a validated liquid chromatographic-tandem mass spectrometric method for quantitative analysis of the potential oak moss allergens atranol and chloroatranol in perfumes and similar products. The method employs LC-MS-MS with electrospray ionization (ESI) in negative mode. The compounds are analysed by selective reaction monitoring (SRM) of 2 or 3 ions for each compound in order to obtain high selectivity and sensitivity. The method has been validated for the following parameters: linearity; repeatability; recovery; limit of detection; and limit of quantification. The limits of detection, 5.0 ng/mL and 2.4 ng/mL, respectively, for atranol and chloroatranol, achieved by this method allowed identification of these compounds at concentrations below those causing allergic skin reactions in oak-moss-sensitive patients. The recovery of chloratranol from spiked perfumes was 96+/-4%. Low recoveries (49+/-5%) were observed for atranol in spiked perfumes, indicating ion suppression caused by matrix components. The method has been applied to the analysis of 10 randomly selected perfumes and similar products.     

On-line hyphenation of capillary electrophoresis with flame-heated furnace atomic absorption spectrometry for trace mercury speciation

Capillary electrophoresis (CE) was directly interfaced to flame-heated furnace atomic absorption spectrometry (FHF-AAS) via a laboratory-made thermospray interface for nanoliter trace element speciation. The CE-FHF-AAS interface integrated the superiorities of stable CE separation, complete sample introduction, and continuous vaporization for AAS detection without the need of extra external heat sources and any post-column derivation steps. To demonstrate the usefulness of the developed hybrid technique for speciation analysis, three environmentally significant and toxic forms of methylmercury (MeHg), phenylmercury (PhHg), and inorganic mercury (Hg(II)) were taken as model analytes. Baseline separation of the three mercury species was achieved by CE in a 60 cm long x 75 microm inner diameter fused-silica capillary at 20 kV and using a mixture of 100 mM boric acid and 10% v/v methanol (pH 8.30) as running electrolyte. The precision (relative standard deviation, RSD, n = 7) of migration time, peak area and peak height for the mercury species at 500 microg x L(-1) (as Hg) level were in the range of 0.9-1.2%, 1.5-1.9%, and 1.4-2.0%, respectively. The detection limit (S/N = 3) of three mercury species was 3.0 +/- 0.15 pg (as Hg), corresponding to 50.8 +/- 2.4 microg x L(-1) (as Hg) for 60 nL sample injection, which was almost independent on specific mercury species. The developed hybrid technique was successfully applied to the speciation analysis of mercury in a certified reference material (DORM-2, dogfish muscle).     

Determination of flavonoids and stilbenes in red wine and related biological products by HPLC and HPLC-ESI-MS-MS

To investigate probable health benefits of flavonoids and stilbenes in red wine a new reversed-phase (RP) high-performance liquid-chromatographic (HPLC) method with enhanced separation efficiency and improved selectivity, sensitivity, and speed has been established for determination of the flavonoids quercetin, myricetin and kaempferol and the stilbenes cis- and trans-resveratrol, in a single run . UV-absorbance, fluorescence (FLD), and mass-spectrometric (MS) detection were also evaluated. UV-absorbance detection at 320 nm for stilbenes and 377 nm for flavonoids enables their determination up to the nanogram range with a linearity of R2>0.9999 (linear range 50 ng mL(-1)-50 microg mL(-1)). Calculated values of average recoveries were between 95 and 105% for all analytes. For resveratrol, fluorescence detection was highly selective and twice as sensitive as UV detection, and linearity was satisfactory (R2>0.9996; linear range see UV detection). For the detection of the hydrophilic glycosidic compounds piceid and rutin, which are coeluted with other hydrophilic ingredients, the validated RP HPLC system was coupled to a quadrupole ion-trap mass-spectrometer (MS) via an electrospray interface (ESI) with 25% ammonia solution as sheath liquid. MS detection was, highly linear (R2>0.9878; linear range 50 ng mL(-1)-50 microg mL(-1)) for all investigated analytes and the limits of detection were in the low nanogram range. Compared with UV detection MS detection resulted in a 200% increase in signal intensity for myricetin and 400% increases for quercetin and kaempferol, but equal signal intensity for resveratrol. Calculated values of average recoveries were 102% for myricetin and 79% for piceid. Collision induced dissociation (CID) was also used to obtain characteristic fragmentation fingerprints to facilitate qualitative and quantitative analysis even in complex matrices. Finally, this hyphenated HPLC-ESI-MS method was highly suitable and an essential improvement compared with UV- and fluorescence detection.     

Development of a method for simultaneous determination of eflucimibe and its three major metabolites in rat plasma by liquid chromatography/electrospray tandem mass spectrometry: a preliminary study

A high-performance liquid chromatography/electrospray ionisation tandem mass spectrometry (HPLC/ESI-MS/MS) method has been developed for the simultaneous determination of eflucimibe, a powerful acyl-coenzyme A cholesterol O-acyltransferase (ACAT) inhibitor, and its main metabolites, in plasma. The ESI and MS/MS parameters were investigated and optimised for each of the four compounds in the positive ion mode. Plasma samples were deproteinised by precipitation with acetonitrile and directly analysed by HPLC/ESI-MS/MS in less than 4 min. Quantitation was performed in the multiple reaction monitoring (MRM) mode for highest sensitivity, selecting the protonated molecules [M+H](+) as precursor ions. The method was demonstrated to be specific and sensitive, and a linear response was observed within a 1-25 ng/mL concentration range. Correlation coefficients (r(2)) greater than 0.9960 were obtained by least-squares regression, and limits of detection down to 0.2 ng/mL were calculated. Therefore, this HPLC/ESI-MS/MS method appears to be an efficient tool, able to provide valuable information for a pharmacological purpose.     

Quantification of the bisphosphonate alendronate using capillary electrophoresis mass spectrometry with dynamic pH barrage junction focusing

A quantitative method was developed for the direct identity confirmation and quantification of alendronate using CE-MS combined with a pH-assisted focusing technique, dynamic pH barrage junction focusing. A pH-induced variation in electrophoretic mobility led to online focusing of alendronate at the sample/pH barrage boundary, significantly improving the detection sensitivity. In addition, the use of a flow-through microvial CE electrospray interface and the multiple reaction monitoring mode of MS further improved the specificity and quantification capability of this technology. This quantitative method presented a wide linear dynamic range over 8–2000 ng/mL and an LOD of 2 ng/mL. A 460-fold improvement in sensitivity was obtained when pH barrage junction focusing was applied during the CE process, in comparison to when normal CE was conducted without online sample stacking. The superior detection sensitivity over previously reported methods enables direct analysis of bisphosphonate compounds, eliminating tedious pre-column sample enrichment and derivatization. Validation of alendronate content in a commercial drug tablet further proved the reliability and power of this method. This simple method with no sample derivatization, superior sensitivity, and short run time (<8 min) is a promising alternative for accurate quantification of alendronate and other types of bisphosphonate compounds in both drug formulations and plasma samples.     

Reagent injection FIA system for lead determination by hydride generation - quartz-tube atomic absorption spectrometry

A method is proposed for the determination of lead by generation of its hydride and detection by quartz-tube AAS using a reagent injection FIA system based on the injection of sodium tetrahydroborate. Lead hydride generation was carried out using a combination of 0.5 M nitric acid, 10% m/ v hydrogen peroxide and 10% m/ v sodium tetrahydroborate. The characteristic concentration obtained was 3.1 ng mL(-1) and the detection limit was 2.6 ng mL(-1) for an injected volume of 0.125 mL of tetrahydroborate.     

High performance liquid chromatography/electrospray tandem mass spectrometry for phenothiazines with heavy side chains in whole blood

Eleven phenothiazine derivatives with heavy side chains contained in human whole blood have been analyzed by high-performance liquid chromatography (HPLC)/electrospray (ES) tandem mass spectrometry (MS). All compounds gave the base peaks due to [M + 1](+) by HPLC/ES single MS. The product ions formed from each quasi-molecular ion by HPLC/ES tandem MS showed the base peaks due to side chains liberated. The mass chromatography of HPLC/ES tandem MS showed much higher sensitivity than that of HPLC/ES single MS for phenothiazines spiked to whole blood. Therefore, regression equations, detection limits, recovery rates and reproducibility were studied for thiethylperazine, clospirazine and flupentixol spiked to human whole blood by means of mass chromatography of HPLC/ES tandem MS. The three compounds showed good linearity in the range of 2-40 ng/mL with a detection limit of about 0.5 ng/mL. Recoveries of the three compounds spiked to whole blood (2 and 8 ng added to 1 mL whole blood) were 43.4-72.5 %; the coefficients of intraday and interday variations were 3.7-9.3 and 12.6-17.9 %, respectively. Thiethylperazine, clospirazine and flupentixol in whole blood could actually be determined with sufficient sensitivity 3 and 6 h after oral administration of 5-10 mg of each compound in a volunteer.     

Interface for coupling nonaqueous wide-bore capillary electrophoresis with mass spectrometry

A liquid-junction-type interface where a thin spraying capillary is inserted inside the separation capillary was constructed for coupling nonaqueous wide-bore capillary electrophoresis (CE) to mass spectrometry (MS). The robust structure of the interface provided fairly easy capillary handling. The study was carried out with uncoated CE capillaries of 200 and 320 microm inner diameter (ID). 1-Propanol-acetonitrile (80:20 v/v) with acetate electrolyte provided a low conducting medium for CE and good spraying conditions for electrospray ionization (ESI) without sheath-flow and drying gas. Methamphetamine, alprenolol, and levorphanol served as model compounds. Approximate detection limits with the 200 microm ID capillary were 35-265 ng/mL.     

Liquid chromatography and tandem mass spectrometry: a powerful approach for the sensitive and rapid multiclass determination of pesticides and transformation products in water

In this paper we will show the results of our research on the direct simultaneous determination of multi-class pesticides and transformation products with different polarities and acid-base properties by applying an on-line trace enrichment coupled to the chromatographic system supplied with electrospray interface (SPE-LC-MS/MS method). The specific chromatographic separation allows the correct determination of almost fifty compounds (37 pesticides and 10 transformation products) using very low sample volume and very little sample handling. Recoveries between 70-120% were obtained for all compounds in drinking and groundwater, meanwhile in surface water 44 compounds were correctly quantified. Relative standard deviations lower than 15% were obtained for all compounds. Even at the lowest concentration level tested (25 ng L(-1)) 40 compounds presented satisfactory recoveries and repeatability. The use of methanol as organic modifier and the increase of injection volume are also studied. The applicability of the developed method to a monitoring programme is demonstrated by applying it to the analysis of hundreds of samples.     

Determination of organotins in natural waters by toluene extraction and graphite furnace AAS

The determination of tributyltin in natural waters by extraction into toluene and graphite-furnace AAS measurement of tin has been investigated. The effect of pH on the extraction of mono-, di- and tributyltin and triphenyltin has been examined and the optimum conditions for the estimation of tributyltin assessed. The AAS performance is greatly improved by using furnace tubes pretreated by soaking in sodium tungstate solution. Such pretreatment is essential if low detection limits are to be attained. Extraction of the tributyltin from aqueous media resulted in a marked signal enhancement (irrespective of the type of furnace tube), which varied according to the nature of the aqueous solution. The enhancement is believed to result from water in the toluene extract activating the tube surface. Methods for the estimation of tributyltin in waters, appropriate for screening samples as part of routine monitoring programmes, are described. With a 1-litre sample, a limit of detection of approximately 4 ng/l. was attained for tin. The relative standard deviation of six replicate analyses of sea-water containing 170 ng/l. tin (present as tributyltin) was 1.5%.     

Development of a rapid and specific assay for detection of busulfan in human plasma by high-performance liquid chromatography/electrospray ionization tandem mass spectrometry

A sensitive and specific assay for detection of busulfan in human plasma was developed. The assay is based on rapid isolation of busulfan by liquid-liquid extraction with ethyl acetate, and detection by high-performance liquid chromatography with electrospray ionization and tandem mass spectrometry. 1,6-Bis(methanesulfonyloxy)hexane, a synthesized analogue of busulfan, was used as the internal standard (IS). The acquisition was performed in the multiple reaction monitoring mode; busulfan and the IS were detected with no interferences from plasma matrix. The method was linear over the range 5-2500 ng mL(-1), with r2 > 0.99 and a run time of only 3.5 min. The intra- and inter-assay precisions were in the ranges 2.1-11.9% and 3.2-10.1%, respectively, and the intra- and inter-assay accuracies were 92.2-107.6% and 94.7-104.1%, respectively. The absolute recoveries were 82.0% (20 ng mL(-1)), 90.6% (1000 ng mL(-1)) and 80.0% (2000 ng mL(-1)) for busulfan, and 89.1% for the IS (1000 ng mL(-1)). The limits of detection and quantification were 2 and 5 ng mL(-1), respectively. The validated method was successfully applied to analyze plasma samples obtained from six adults receiving doses of 1 mg kg(-1) in a conditioning regimen prior to bone marrow transplantation. A marked intra-patient variation in busulfan concentrations during the steady state was observed, which limits the application of pharmacokinetic modeling and suggests that continuous therapeutic monitoring is necessary for adequate individualized dosing. In this regard, the present assay brings important advantages relative to other methods described in the literature, i.e., it is highly specific and simple to perform, with a rapid chromatographic run time (3.5 min), and the whole procedure can be completed in 4-5 h, which would permit dose corrections after the third dose allowing earlier and better dosing adjustments towards the target level of busulfan.     

The quantitative determination of tinalkylates in sediments

A procedure has been developed for the determination of dibutyltin and tributyltin cations in sediments at the ng/g level. The extraction using butylacetate/methanol has been given the best recovery. Sufficient separation has been obtained with a cation exchange column and a acetonitrile/water/acetic acid buffer solvent system for the determination of the species using thermospray MS and selected ion monitoring. Detection limits of 1.3 ng/g for DBT and 1.7 ng/g for TBT have been obtained. The procedure is robust and the sensitivity is stable over a long time.Dedicated to Prof. Dr. Dieter Klockow on the occasion of his 60th birthday     

Determination of Tributyltin in Sea Water by Hydride Generation-Atomic Absorption Spectrometry

A hydride generation-atomic absorption spectrometry (HG-AAS) procedure is described for the analysis of tributyltin (TBT) in sea water. TBT is first converted to its volatile hydride form by reaction with sodium borohydride, followed by cryogenic trapping at ?196°C, and finally detection by atomic absorption spectrometry using an electrically heated quartz atomization cell. The linear range of calibration is 5-250 ng TBT (as tin). At the 5-ng level, the relative standard deviation (RSD) is 13%. The absolute detection limit (3σ) is 1.8 ng. Based on a sample volume of 500 mL, this value corresponds to a concentration detection limit 3.6 ng L^?1 TBT This method has been successfully applied to the analysis of TBT in sea water collected from Keelung and Kaohsiung harbors.     

Occurrence and analysis of estrogens and progestogens in river sediments by liquid chromatography-electrospray-mass spectrometry

In this study, an analytical procedure for the determination in sediment of the most abundant and/or physiological active estrogens (estradiol, estriol, estrone, ethynyl estradiol, and diethylstilbestrol) and progestogens (progesterone, norethindrone. and levonorgestrel) is described. The procedure includes ultrasonic extraction of the lyophilized sediment, clean-up with octadecylsilica cartridges, and analysis by liquid chromatography-diode array detection-mass spectrometry (LC-DAD-MS). MS detection is performed with an electrospray interface in the positive ion mode for determination of the progestogens and in the negative ion mode for determination of the estrogens. The method was applied to the determination of the target compounds in river sediments from the area of Catalonia. Estrogens and progestogens were found at concentrations usually in the low ng g(-1) range. Estriol and norethindrone were the compounds most frequently found whereas maximum concentrations in all sediment samples were obtained for ethynyl estradiol (22.8 ng g(-1)) and estrone (11.9 ng g(-1)). Detection limits were in the range of 0.04-1.00 ng g(-1). Preliminary conjectures with regards to the environmental behavior and impact of estrogens and progestogens in rivers are made. To the authors' knowledge, this is the first work reporting a detailed method for the analysis of estrogens and progestogens in river sediments and data on the environmental occurrence of both groups of compounds.     

Sheath liquid interface for the coupling of normal-phase liquid chromatography with electrospray mass spectrometry and its application to the analysis of neoflavonoids

A novel interface that allows normal-phase liquid chromatography to be coupled with electrospray ionization (ESI) is reported. A make-up solution of 60 mM ammonium acetate in methanol, infused at a 5 microl min(-1) flow-rate at the tip of the electrospray probe, provides a sheath liquid which is poorly miscible with the chromatographic effluent, but promotes efficient ionization of the targeted analytes. Protonated molecules generated in the ESI source were subjected to tandem mass spectrometric experiments in a triple-quadrupole mass spectrometer. The main fragmentation reactions were characterized for each analyte and specific mass spectral transitions were used to acquire chromatographic data in the multiple reaction monitoring detection mode. Results obtained during optimization of the sheath liquid composition and flow-rate suggest that the electrospray process was mainly under the control of the make-up solution, and that it forms an external charged layer around a neutral chromatographic mobile phase core. This sheath liquid interface was implemented for the analysis of some neoflavonoid compounds and its performance was evaluated. Limits of detection were established for calophillolide, inophyllum B, inophyllum P and inophyllum C at 100, 25, 15 and 100 ng ml(-1), respectively.     

Capillary high-performance liquid chromatography with mass spectrometry for simultaneous determination of major flavonoids, iridoid glucosides and saponins in Flos Lonicerae

Flos Lonicerae, a traditional herbal medicine, has been used in China to treat some inflammatory disease. Several different classes of compounds have been separated from the herb to assess their pharmacological activities. Among these classes, flavonoids, iridoid glycosides and saponins have been well studied and may be responsible for its clinical application. Therefore, quality control of Flos Lonicerae is an important issue for drug safety and validity evaluations. A quantitative method consisting of solid phase extraction followed by capillary high-performance liquid chromatography-diode array detection/electrospray ionization mass spectrometry (capillary HPLC-DAD/ESI-MS) was developed for simultaneously assay of 24 compounds in Flos Lonicerae. Under optimized capillary HPLC-DAD/ESI-MS conditions, these compounds, including nine flavonoids, eight iridoid glucosides and seven saponins, were separated with high efficiency in the selected-ion monitoring (SIM) mode. Linearity of the method was good with correlation coefficients (r(2)) in the range of 0.9935-0.9998 and detection limits were lower than 2.57 ng/mL for most of analytes. The obtained recoveries varied between 91.0 and 108.7% with the relative standard deviations (RSDs) within 8.74% (n=3). The capillary HPLC-DAD/ESI-MS method was also successfully applied to the analysis of these compounds in five species of Flos Lonicerae. It was demonstrated to be a powerful tool for comprehensive analysis of herbal medicines, owing to its exclusive selectivity and excellent sensitivity.     

Investigation of HfO(+) interference in the determination of platinum in a catalytic converter (cordierite) by inductively coupled plasma mass spectrometry

The determination of Pt in cordierite is subject to strong interference by spectral overlap from HfO(+) ions with all Pt isotopes. Two mathematical correction methods based on the HfO(+)Hf(+) ratio and a method for the chemical separation of Hf based on adsorption chromatography and isotope dilution were investigated to correct for this interference. Flow infection was used to prevent clogging of the cone orifice. To enhance the sensitivity and thus lower the detection limit, thermospray nebulization was used for sample introduction and the method was compared with pneumatic nebulization. In addition, the memory effects were evaulated for both systems. Analysis of artificial solutions (1 ng Pt ml(-1)) yielded results within 3% of the true value. Th Pt content (ca. 50 ng g(-1)) of a cordierite sample, previously exposed to exhaust gases, could be determined with precisions of about 10-25% and the results agreed with earlier determinations by other workers.     

Determination of huperzine A in human plasma by liquid chromatography-electrospray tandem mass spectrometry: application to a bioequivalence study on Chinese volunteers

A simple, sensitive and selective LC-MS-MS method has been developed for the quantification of huperzine A in human plasma. Huperzine A and pseudoephedrine hydrochloride (internal standard) were isolated from human plasma by extraction with ethyl acetate, chromatographed on a C(18) column with a mobile phase consisting of 0.2% formic acid-methanol (15:85, v/v) and detected using a tandem mass spectrometer with an electrospray ionization interface. The lower limit of quantification was 0.0508 ng/mL, and the assay exhibited a linear range of 0.0508-5.08 ng/mL (r = 0.9998). The method was successfully applied to investigate the bioequivalence between two kinds of tablets (test vs reference product) in 18 healthy male Chinese volunteers. After a single 0.2 mg dose for the test and reference product, the resulting means of major pharmacokinetic parameters such as AUC(0-24), AUC(0-infinity), C(max), T(max) and t(1/2) of huperzine A were 16.35 +/- 3.42 vs 16.38 +/- 3.61 ng h/mL, 17.53 +/- 3.80 vs 17.70 +/- 3.97 ng h/mL, 2.47 +/- 0.49 vs 2.51 +/- 0.51 ng/mL, 1.3 +/- 0.4 vs 1.2 +/- 0.3 h and 5.92 +/- 0.75 vs 6.18 +/- 0.66 h, respectively, indicating that these two kinds of tablets were bioequivalent.