Sensitive spectrophotometric determination of vanadium with 2-(5-bromo-2-pyridylazo)-5-diethyl-aminophenol (5-Br-PADAP)

A new sensitive and highly selective method is described for the spectrophotometric determination of microgram amounts of vanadium(V). First, vanadium is isolated by extraction withN-benzoyl-N-phenylhydroxylamine (BPHA) in chloroform from about 4M hydrochloric acid medium. Then, chloroform is evaporated and the residue mineralized with mixture of cone. perchloric and nitric acid. Finally, a colour reaction of vanadium(V) separated with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) in an acetate buffer (pH 4.5) gives a molar absorptivity of 5.48×10⁴l·mol^–1·cm^–1 at 585 nm. The proposed method was applied for the determination of traces of vanadium in aluminium samples. The results obtained show a good precision and accuracy of the method.     

Preconcentration and Determination of Trace Nickel Using 1-(2-Pyridylazo)-2-Naphtol (PAN) Immobilized on Surfactant-Coated Alumina

A microcolumn of alumina modified with sodium dodecyl sulfate (SDS) and 1-(2-pyridylazo)-2-naphthol (PAN) was prepared for the preconcentration of trace nickel from water samples for a flame atomic absorption spectrometry (FAAS) determination. Under optimized conditions (pH = 4.0; flow rate, 5 mL min^–1) nickel (II) was retained on the column. The nickel collected on the column was eluted with 5 mL of 0.5 M nitric acid. Recovery was greater than 96.7%. A concentration factor of 300 can be achieved by passing 1500 mL of sample through the microcolumn. The relative standard deviation (ten replicate analyses) at the 40 ng mL^–1 level for nickel was 2.4%, and the corresponding limit of detection (based on 3) was 0.06 ng mL^–1. The method was applied to the determination of Ni in waste and mineral waters.     

Spectrophotometric determination of vanadium(IV) in the presence of vanadium(V) using Br-PADAP

In the present paper, a simple and sensitive method is proposed for vanadium(IV) determination in the presence of vanadium(V). This is based on the oxidation of vanadium(IV) present in the sample to vanadium(V) by addition of iron(III) cation, followed by a complexation reaction of iron(II) with the spectrophotometric reagent 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP). The iron(II) reacts with Br-PADAP immediately, forming a stable complex with a large molar absorptivity. The vanadium(IV) determination is possible, with a calibration sensitivity of 0.549 g ml^–1, for an analytical curve of 18.8 ng ml^–1 to 2.40 g ml^–1, molar absorptivity of 2.80 × 10⁴ 1 mole^–1 cm^–1 and a detection limit of 5.5 ng ml^–1. Selectivity was increased with the use of EDTA as a masking agent. The proposed method was applied for the vanadium(IV) determination in the presence of several amounts of vanadium(V). The results revealed that 200 g of vanadium(V) do not interfere with determination of 5.00 g of vanadium(IV). The precision and the accuracy obtained were satisfactory (R. S. D.<2%).     

Extraction-spectrophotometric determination of trace iron (II) in sea water with 2-[2-(3,5-dibromopyridyl)azo]-5-diethylaminobenzoic acid

An extraction-spectrophotometric method is described for the determination of traces of iron(II) with 2-[2-(3,5-dibromopyridyl)azo]-5-diethyl-aminobenzoic acid. The reagent forms a stable and blue 12 iron/reagent complex that can be extracted into chloroform. The apparent molar absorptivity of the iron(II) complex is 1.09 × 10⁵ 1 mol^–1 cm^–1 at 624 nm in chloroform. The reagent is relatively selective; interferences from cobalt, copper, nickel and vanadium can be removed by using dimethylglyoxime and EDTA. The method is applied to the determination of iron (II) in sea water and aluminium alloys with good precision and accuracy.     

Spectrophotometic Determination Of Tin In Steels With2-(5-Nltro-2-Pyridylazo)-5-[N-n-Propyl-N-(3-Sulfopropyl)Amino]phenol

ABSTRACT

A highly sensitive azo dye, 2-(5-nitro-2-pyridylazo)-5-[N-n-propyl-N-(3-sulfopropyl)amino]phenol (Nitro-PAPS), is used as a colorimetric reagent for the determination of tin(IV) content. Nitro-PAPS reacts with tin(IV) to form a water-soluble complex in 1.0 M acetic acid. Full color development is attained within 5 minutes, and maintains constant absorbance for at least 24 hours. The apparent molar absorptivity is 7.7 x 10⁴ dm³ mol^?1 cm^?1 at a maximum wavelength of 580 ran. Beer's law is obeyed for tin(IV) in the range of 0-1.2 μg ml^?1. The proposed method is successfully applied to the determination of trace amounts of tin in steels.     

Determination of V(V), Nb(V) and Ta(V) as their 2-(5-nitro-2-pyridylazo)-5-diethylaminophenol complexes by reversed-phase high performance liquid chromatography

A method for the reversed-phase liquid chromatographic separation and determination of V(V), Nb(V) and Ta(V) as 2-(5-nitro-2-pyridylazo)-5 diethylaminophenol (5-NO₂-PADAP) complexes is reported. The metal complexes were eluted in 9 min with a mobile phase of methanol-water (54 : 46, v/v) containing 10 mmol L^–1 acetate buffer (pH 3.0) on an ODS column. The detection limits for V, Nb and Ta were 0.09, 0.13 and 1.41 ng mL^–1, respectively, with S/N=3. The analysis of a reference sample of a mineral is discussed. The results corresponded to the certified values, and recoveries of 98.3–101.4% have been obtained.     

Determination of 6-amino-2,2-dimethyl-1,3-dioxepan-5-ol by postcolumn derivatization witho-phthalaldehyde/2-mercapto-ethanol after ion-pair chromatography

Summary A high-performance liquid chromatographic method is discribed for the determination of 6-amino-2,2-dimethyl-1,3-dioxepan-5-ol using Spherisorb ODS II stationary phase and mobile phase 30:70 (v/v) methanol: aqueous 1-octane sulfonic acid. Detection was fluorimetric following postcolumn derivatization with o-phthaladehyde/2-mercaptoethanol. The procedure was applied to the analysis of aqueous solutions and microcrystalline suspensions in liquid paraffin, prepared for investigation of the toxicological profile. The method was validated for selectivity, linearity of detector response, repeatability, limit of detection and quantitation. The HPLC method was selective. The instrumental limit of detection was 0.5 ng per injection (0.05 g mL^–1). The method detection limits were 0.5 g mL^–1 aqueous solution and 5 g mL^–1 liquid paraffin suspension, the quantitation limit 0.05 mg mL^–1 aqueous solution and 1.0 mg mL^–1 liquid paraffin. Linearity was within 0.94–47.1 g mL^–1. Intra-assay accuracy accounted for 99–100% in the range 0.05–226 mg mL^–1 aqueous solution, intra-assay precision for 2% (C.V.). For microcrystalline liquid paraffin suspensions with 1 and 250 mg mL^–1 99 and 109% was found for intra-assay accuracy. Intra-assay precision was 5% (C.V.). Reliable results over a wide concentration range can be obtained. The procedure is considered valid for determination of the analyte in aqueous solution or microcrystalline paraffin oil suspensions.     

2-(2-Thiazolylazo)-p-cresol as a spectrophotometric reagent for vanadium determination in the presence of ascorbic acid

The present work describes the use of 2-(2-thiazolylazo)-p-cresol (TAC) as a spectrophotometric reagent for vanadium determination. TAC reacts with vanadium(IV) in the presence of ascorbic acid, forming a red complex with absorption maximum at 525 nm. The following parameters were studied: complex stability, pH effect, amount of TAC, amount of acetate buffer, HEDTA effect, order of addition of reagents and Beer's law validity. TAC can be used for vanadium determination in the pH range 4.6–6.0, with molar absorptivity of 2.11 × 10⁴Lmole^–1 cm^–1 (at525nm). Beer's law is obeyed up to 2.0 g mL^–1. Many cation interferences can be easily eliminated by using HEDTA as a masking agent. Steel reference standards were used to test the proposed procedure and the accuracy and precision obtained were satisfactory.     

Kinetic Determination of Mercury(II) at Trace Level from Its Catalytic Effect on a Ligand Substitution Process

A catalytic kinetic method (CKM) is presented for the determination of mercury(II) based on its catalytic effect on the rate of substitution of N-methylpyrazinium ion (Mpz⁺) onto hexacyanoferrate(II). The progress of the reaction was monitored spectrophotometrically at 655 nm by registering the increase in absorbance of the product [Fe(CN)₅(Mpz]²⁻ under the reaction conditions: 5 × 10⁻³ mol L⁻¹ [Fe(CN)₆]⁴⁻), 5 × 10⁻⁵ mol L⁻¹ [Mpz⁺], T = 25.0 ± 0.1°C, pH 5.00 ± 0.02 and ionic strength, I = 0.1 mol L⁻¹ (KNO₃). Quantitative rate data at specified experimental conditions showed a linear dependence of the absorbance after fixed time A _t on the concentration of mercury(II) catalyst in the range 20.06–702.1 ng mL⁻¹. The maximum relative standard deviations and percentage errors for the determination of mercury(II) in the range of 20.06–200.6 ng mL⁻¹ were calculated to be 1.7 and 2.7% respectively. The detection limit was found to be 7.2 ng mL⁻¹ of mercury(II). Accuracy (expressed in terms of recoveries) was in the range of 98–103%. Figures of merit and interference due to many cations and anions was investigated and discussed. The applicability of the method was demonstrated by determining the mercury(II) in different synthetic samples and confirming the results using atomic absorption spectrophotometry. The proposed method allowed determination of mercury(II) in the range 20.06–702.1 ng mL⁻¹ with very good selectivity and an output of 30 samples h⁻¹.__________From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 6, 2005, pp. 654–661.Original English Text Copyright © 2005 by Surendra Prasad.This article was submitted by the author in English.     

Ethylisobutrazine hydrochloride as a selective and sensitive reagent for the spectrophotometric determination of vanadium(V) and its application to vanadium-bearing minerals and alloys

Ethylisobutrazine hydrochloride is proposed as a selective and sensitive reagent for the spectrophotometric determination of vanadium(V). It forms a red-colored species with vanadium(V) in 3.5–6.5 M phosphoric acid medium. An eight-fold molar excess of reagent is necessary for the full development of the color. The red species exhibits an absorption maximum at 518 nm with a molar absorptivity of 9.75 × 10³ liters mol⁻¹ cm⁻¹. Sandell's sensitivity is 5.2 ng cm⁻². Beer's law is obeyed over the range 0.1–6.2 ppm of vanadium(V) with an optimum concentration range of 0.4–6.0 ppm. The effects of acidity, time, temperature, order of addition of reagents, reagent concentration, and the interferences from various ions, are reported. The method has been used successfully for the determination of vanadium in ilmenite and vanadium steels that contain chromium, molybdenum, manganese, nickel, copper, tungsten, and titanium.     

A study of the spectrophotometric determination of traces of cadmium(II) and copper(II) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in the presence of polyglycol octylphenyl ether

A spectrophotometric study of the Cd(II) and Cu(II) complex of a new reagent, 2-(5-bromo-2-pyridylazo)-5-diethylamino phenol (5-Br-PADAP) in the presence of polyglycol octylphenyl ether (OP) is presented. A reddish binary complex is formed at pH 9 and shows maximal absorbance at 560 nm with molar absorptivity of 1.16 × 10⁵ · mol⁻¹ · cm⁻¹ liter (Cd), 1.5 × 10⁵ mol⁻¹ · cm⁻¹ · liter (Cu). Beer's law is followed over the range 0.0 to 20 μg cadmium(II) and 0.0–18 μg copper(II). The continuous variation method and molar ratio method showed that the metal ligand ratio is 1:2; ordinarily, most ions do not interfere with the determination and the method can be applied for direct spectrophotometric determination of cadmium(II) and copper(II) in actual samples and the results obtained are satisfactory.     

A sensitive and specific HPLC-MS method for the determination of sophoridine,sophocarpine and matrine in rabbit plasma

A sensitive and specific method was developed for the determination of sophoridine (SRI), sophocarpine (SC) and matrine (MT) in rabbit plasma by HPLC-MS. After an administration of Kuhuang by injection, blood samples were collected and extracted with methanol. The extract solutions were analysed by HPLC-MS method. The separation was performed on a ZORBAX Extend-C18 column using methanol/water/diethylamine (50:50:0.07, v/v/v) as mobile phase. The quinolizidine alkaloids were detected by using mass spectrometry in the SIM mode. There was a good linear relationship between peak area and concentration of analytes over the concentration range of 13.2–995.0 ng mL^–1 for SRI, 7.0–530.0 ng mL^–1 for SC and 8.8–655.0 ng mL^–1 for MT, respectively. The absolute recovery of this method was more than 57% for SRI, 87% for SC and 91% for MT. The accuracy of assay was more than 90%. The limits of detection (LODs) were 6.8 ng mL^–1 for SRI, 3.5 ng mL^–1 for SC and 4.2 ng mL^–1 for MT, respectively. The limits of quantitation (LOQs) were 13.2 ng mL^–1 for SRI, 7.0 ng mL^–1 for SC and 8.8 ng mL^–1 for MT, respectively. The intra-day and inter-day coefficients of variation (RSDs) were less than 10.1, 6.3 and 5.8% for SRI, SC and MT, respectively. The developed method was applied to determine the concentration–time profiles of SRI, SC and MT in rabbit plasma after injection of Kuhuang.     

Sensitive spectrophotometric determination of ascorbic acid in fruit juices and pharmaceutical formulations using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP)

A simple and very sensitive method has been developed for the determination of ascorbic acid based on the oxidation of ascorbic acid to dehydroascorbic acid by iron(III), followed by a complexation of iron(II) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol(Br-PADAP). The iron(II) complex is formed immediately, with absorption maxima at 560 and 748 nm and a molar absorptivity of 1.31 × 10⁵ l mole^–1cm^–1 and 5.69 × 10⁴ l mole^–1cm^–1, respectively. The ascorbic acid determination is possible with a linear range up to 2.4 μg ml^–1, a calibration sensitivity of 0.744 ml μg^–1 at 560 nm and 0.323 ml μg^–1 at 748 nm, and a detection limit of 15 ng ml^–1 and 44 ng ml^–1, respectively. The procedure was used for the ascorbic acid determination in several fruit juices and pharmaceutical formulations. The results demonstrated a good precision (R.S.D. < 1%) and are in agreement with those obtained with others methods. The Br-PADAP method proposed is six times more sensitive than the method using the iron(II)-1,10-phenanthroline system. Received: 7 May 1996 / Revised: 1 July 1996 / Accepted: 8 August 1996     

Sensitive spectrophotometric determination of ascorbic acid in fruit juices and pharmaceutical formulations using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP)

A simple and very sensitive method has been developed for the determination of ascorbic acid based on the oxidation of ascorbic acid to dehydroascorbic acid by iron(III), followed by a complexation of iron(II) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol(Br-PADAP). The iron(II) complex is formed immediately, with absorption maxima at 560 and 748 nm and a molar absorptivity of 1.31 × 10⁵ l mole^–1cm^–1 and 5.69 × 10⁴ l mole^–1cm^–1, respectively. The ascorbic acid determination is possible with a linear range up to 2.4 μg ml^–1, a calibration sensitivity of 0.744 ml μg^–1 at 560 nm and 0.323 ml μg^–1 at 748 nm, and a detection limit of 15 ng ml^–1 and 44 ng ml^–1, respectively. The procedure was used for the ascorbic acid determination in several fruit juices and pharmaceutical formulations. The results demonstrated a good precision (R.S.D. < 1%) and are in agreement with those obtained with others methods. The Br-PADAP method proposed is six times more sensitive than the method using the iron(II)-1,10-phenanthroline system. Received: 7 May 1996 / Revised: 1 July 1996 / Accepted: 8 August 1996     

Spectrophotometric determination of iron in alloys and ores with 1-(2-pyridylmethylideneamine)-5-(salicylideneamine)thiourea

Summary A spectrophotometric method for the determination of iron is described. The green Fe(II) complex is formed at pH 4.8 in a medium containing 40% dimethylformamide and 0.8 g/l ascorbic acid, and the absorbance is measured at 635 nm. The molar absorptivity is 5.7×10³lo·mole^–1·cm^–1. The method has been applied with good results to the determination of iron in six alloys and ores.

---

Spektrophotometrische Bestimmung von Eisen in Legierungen und Erzen mit 1-(2-Pyridylmethylidenamin)-5-(salicylidenamin)-thioharnstoff

Zusammenfassung Ein spektrophotometrisches Verfahren zur Eisenbestimmung wurde beschrieben. Der grüne Fe(II)-Komplex bildet sich bei pH 4,8 in einem Medium aus 40% Dimethylformamid und 0,8 g/l Askorbinsäure. Die Absorbanz wird bei 635 nm gemessen. Die molare Absorptivität beträgt 5,7× 10³l·mol^–1·cm^–1. Die Methode gab gute Resultate bei der Bestimmung von Eisen in sechs Legierungen und Erzen.

     

Highly Sensitive Spectrofluorimetric Determination of Trace Amounts of Indium with 5-Bromine-Salicylaldehyde Salicyloylhygrazone

The fluorescence reaction of 5-bromine-salicylaldehyde salicyloylhydrazone (5-Br-SASH) with indium was studied in detail. Based on this chelating reaction, a sensitive spectrofluorimetric method was developed for the determination of indium in a water–ethanol (63%) medium at PH 4.6. Under these conditions, the In-5-Br-SASH complex has excitation and emission maxima at 395 nm and 461 nm, respectively. The linear range of the method is from 0 to 1000 ng mL^–1and the detection limit is 2.4 ng mL^–1of indium. The molar ratio of indium to the reagent is 1 : 3. Interferences from other ions were studied. The method was successfully applied to the determination of indium in lead, tin, spelter, zinc sulfide using the standard additions method.     

Determination of titanium by adsorption-voltammetry with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP)

Summary The 1:1 complex between titanium (IV) and 5-Br-PADAP can be used to determine titanium by adsorption voltammetry at a stationary Hg-electrode. The experimental conditions for the determination are described. The detection limit is 3×10^–10 mol/l Ti (0.015 ppb). Calibration curves are linear for solutions containing 4×10^–10 to 5×10^–8 mol/l Ti(IV) and an enrichment time of 3 min. The influence of foreign ions was investigated. The determination can be carried out in the presence of a 5000-fold excess of iron.     

Extraction and spectrophotometric determination of vanadium with 4-(2-thiazolylazo)resorcinol and tetraphenylarsonium and phosphonium chlorides

Extraction of vanadium-4-(2-thiazolylazo)resorcinol complexes by quaternary salts such as triphenylmethylarsonium iodide, tetraphenylarsonium chloride, and tetraphenylphosphonium chloride has been studied. Quantitative extraction is achieved with tetraphenylarsonium and tetraphenylphosphonium chlorides in the pH region between 3.5 and 5. The optimum conditions for the extraction and spectrophotometric determination of vanadium in the extract are: pH 3.8–4.0, the concentration of vanadium 0.1–0.4 μg/ml. Effective molar absorptivity at λ_max = 555 is (2.55 ± 0.05) × 10⁴ liters mol⁻¹ cm⁻¹. Beer's law is obeyed. Relative standard deviation is 2–10% depending on the concentration level. The composition of the extracted complexes was studied in the solution and in the solid state. For their characterization chemical and spectral evidence and comparison with the vanadium-PAR complexes have been combined.     

Determination of 5-n-Butyl-4-{4-[2-(1H-tetrazole-5-yl)-1H-pyrrol-1-yl]phenylmethyl}-2,4-dihydro-2-(2,6-dichloridephenyl)-3H-1,2,4-triazol-3-one, a New Angiotensin Type 1 Receptor Antagonist in Rat Plasma by LC-ESI-MS: Application to Pharmacokinetic Studies

A simple and sensitive reversed-phase LC-ESI-MS method to identify and quantitate 5-n-butyl-4-{4-[2-(1H-tetrazole-5-yl)-1H-pyrrol-1-yl]phenylmethyl}-2,4-dihydro-2-(2,6-dichloridephenyl)-3H-1,2,4-triazol-3-one (1b), a new Angiotensin II type 1 receptor antagonist in rat plasma has been developed and validated. Sample preparation used a simple liquid–liquid extraction with ethyl acetate. Separation was achieved by gradient elution on a C₁₈ column. The mobile phase consisted of acetonitrile and water (0.05% triethylamine and 0.05% acetic acid) at a flow rate of 0.2 mL min⁻¹. The detection utilized selected ion monitoring (SIM) in the negative mode at m/z 507.1 and m/z 407.2 for the deprotonated molecular ions of 1b and the internal standard irbesartan, respectively. The lower limit of quantification was reproducible at 5 ng mL⁻¹ with 100 μL of plasma and the good linear was observed in the 5–500 ng mL⁻¹ range. This concentration range corresponded well with the plasma concentrations of 1b in pharmacokinetic studies. Recoveries of 1b in rat plasma were 76.1, 74.6 and 79.0% at 5, 50 and 500 ng mL⁻¹. The RSD of intra-assay and inter-assay variations were all less than 5%. This validated LC-ESI-MS assay is an economic, quick, precise and reliable method for the analysis of 1b in pharmacokinetic studies.     

Spectrophotometric determination of cadmium with 1-[(5-chloro-2-pyridyl)azo]-2-naphthol

Summary Cadmium(II) reacts with l-[(5-chloro-2-pyridyl)azo]-2-naphthol (5-C1--PAN) in aqueous solution; the complex can be extracted with chloroform at pH 9–11 to give a red solution with an absorption peak at 566 nm. The colour in chloroform is stable and the system conforms to Beer's law; optimal range in the chloroform layer for measurement at 1.00-cm cells is 0.1–1 ppm cadmium. Common cations and anions do not interfere. Large amounts of some cations can be masked by potassium cyanide, the cadmium cyanide complex being demasked by formaldehyde. The proposed method is one of the most sensitive procedure for the determination of cadmium. The molar absorptivity in the chloroform extract is 6.6· 10⁴ 1 mole^–1 cm^–2 at 566 nm.

---

Zusammenfassung Cadmium reagiert mit 1-(5-Chlor-2-pyridyl) azo-2-naphthol, 5-C1--PAN, in wäßriger Lösung; der rote Komplex kann bei pH 9–11 mit Chloroform extrahiert werden und hat ein Absorptionsmaximum bei 566 nm. Die chloroformische Lösung ist stabil und entspricht dem Beerschen Gesetz; für die Messung in l-cm-Küvetten eignen sich am besten 0,1–1 ppm Cd. Übliche Ionen stören nicht. Große Mengen einiger Kationen können mit KCN maskiert werden, wahrend [Cd(CN)₄]^2– von Formaldehyd gespalten wird. Die vorgeschlagene Methode ist eine der empfindlichsten für die Bestimmung von Cd. Die molare Extinktion des chloroformischen Extraktes betragt bei 566 nm 6,6 · 10⁴ 1 · mol^–1 · cm^–2.