掺杂Eu3+离子LaPO4的合成及其发光特性研究

采用固相反应法合成了掺杂Eu3+离子的LaPO4,并用X射线粉末衍射对其结构进行了表征.XRD数据经计算机处理表明:LaPO4属单斜晶系,晶胞参数a=6.84A,b=7.08A,c=6.46A,β=103.85°,属P21/n(No.14)空间群.测定了其激发光谱和发射光谱,光谱数据表明:在掺杂Eu3+离子的LaPO4荧光体中,基质LaPO4的电荷迁移激发态的能量能有效地传递到Eu3+离子,说明基质LaPO4本身对发光有贡献.位于592,612 nm附近的2个发射峰均出现劈裂现象,即有2个5D0→7F1(590,594nm)、2个5D0→7F2(610,614nm)发射峰,说明掺杂的Eu3+离子在LaPO4晶体中有着不相同的配位环境,推测Eu3+离子处于D2d或D3对称格位.     

稀土离子与苯并咪唑二羧酸和邻菲啰啉配合物:晶体结构、荧光及对有机小分子的荧光传感

合成了两种新的配合物{[Eu3(bidc)4(phen)2(NO3)]·2H2O}n(1)和[Tb2(bidc)3(H2O)2](2)(bidc=苯并咪唑二羧酸根,phen=1,10-邻菲啰啉)。配合物1是链状结构,含有三种不同的金属离子配位环境:Eu(1)O6N2,Eu(2)O8和Eu(3)O6N2。配合物2是二维网状结构,含有两种配位环境相似的金属离子:Tb(1)O8和Tb(2)O8。配合物1在581,593,615,654和702nm处出现发射峰,为Eu3+的5 D0→7 FJ(J=0-4)跃迁产生的特征荧光。最强发射峰位于615nm,对应于5 D0→7 F2跃迁,为红光。跃迁强度I(5 D0→7 F2)∶I(5 D0→7 F1)约为2.5,说明Eu3+不处于反演中心。配合物2在490,545,584和622nm出现发射峰,归属为中心Tb3+的5 D4→7 FJ(J=6-3)跃迁产生的特征荧光。在545nm的发射最强,对应于5 D4→7 F5跃迁,为绿光。探讨了不同溶剂对配合物1和2荧光的影响。实验结果表明硝基苯对配合物1和2具有显著的荧光猝灭作用,因此配合物1和2可用于环境污染物硝基苯的检测。     

Ca0.8La0.2-x-yMoO4∶xTb3+,yEu3+荧光材料的水热合成及多色发光性质

采用水热法制备了Ca0.8La0.2-x-y MoO4∶xTb3+,yEu3+荧光材料,并对其结构和发光性能进行了研究。X射线衍射(XRD)分析表明,合成的样品为四方晶系的CaMoO4白钨矿结构,稀土离子La3+、Eu3+、Tb3+的引入不会改变主晶格的结构。荧光光谱表明,与CaMoO4∶Eu3+荧光粉相比,基质中掺杂La后的Ca0.8La0.15MoO4∶0.05Eu3+样品的616 nm(5D0→7F2)处的特征发射峰明显增强。在285 nm紫外光激发下,Ca0.8La0.16-y MoO4∶0.04Tb3+,yEu3+(y=0.01,0.03,0.05,0.07)系列样品在545 nm和616 nm处出现的发射峰,分别对应于Tb3+的5D4→7F5跃迁和Eu3+的5D0→7F2跃迁,并且随着Eu3+掺杂量的增加,Tb3+的发射峰逐渐减弱,Eu3+的发射峰逐渐增强,表明该荧光材料中存在着由Tb3+到Eu3+能量传递。随着Ca0.8La0.16-y MoO4∶0.04Tb3+,yEu3+(y=0.01,0.03,0.05,0.07)系列样品中激活剂Eu3+掺杂量的增加,荧光粉实现了从绿色→黄绿→黄色→红色的颜色可调。     

SrWO4∶Eu,Tb发光材料的结构表征与发光性能

采用液相沉淀法合成了SrWO4:Eu,Tb发光材料,XRD衍射测试结果表明,合成材料均具有四方晶系结构.荧光光谱检测表明,在254nm紫外光激发下,SrWO4;0.05Eu的发射光谱出现Eu3+的5D0→7F1(598nm)、5D0→7F2(618nm)跃迁发光峰,SrWO4:0.05Eu,0.05Tb的发射光谱只出现Eu3+的发光峰,说明存在Tb3+,Eu3+离子间的能量传递现象,Tb3+离子的共掺杂能够显著提高Eu3+离子的发光性能.     

纳米二氧化钛的制备及Eu~(3+)掺杂发光研究

以钛酸四丁酯为前驱物,采用溶胶-凝胶法制备了四种不同配方Eu3+掺杂的TiO2纳米晶.利用扫描电镜(SEM)、EDS能谱、光致发光光谱对样品的形貌、成份及性能进行了表征.研究了退火温度、稀土Eu3+离子掺杂摩尔分数、溶剂乙醇量等对发光性能的影响,并对其发光机理进行了探讨.结果表明:稀土Eu3+掺杂TiO2纳米晶样品,掺杂均匀、颗粒大约在30～80nm;从EDS能谱分析可得Ti:O原子个数比并不是按化学计量TiO2满足1:2,这是因为在TiO2中形成的是Ti-O-Ti键,Eu3+离子很可能取代了Ti4+离子,同时又形成了氧空位,表明稀土Eu3+离子进入TiO2晶格中;样品的主发射峰在614nm(5D0→7F2)处发光最强,且在593nm(5D0→7F1)处出现了属于磁偶极跃迁的发射峰,制备Eu3+∶TiO2纳米晶的组分、退火温度、溶剂乙醇的量不同,发射光谱的强度也不同.     

SrWO4∶Eu3+纳米晶的合成、表征和光致发光性能

用CTAB辅助水热法合成了四方相的SrWO4∶Eu3+纳米晶体。通过X射线衍射仪和扫描电子显微镜等测试手段对样品进行了表征。SrWO4∶Eu3+纳米晶粒尺寸随着反应溶液中Eu3+离子和CTAB含量的增加而减小。在393 nm光激发下,观察到5D0→7F J(J=1,2,3,4)和5D1→7F0跃迁,并且5D0→7F2跃迁的发射最强,表明Eu3+在SrWO4基质中占据了非对称中心的格位。发射峰的位置与激发波长无关。     

Sr_2ZnSi_2O_7∶Eu~(3+)的低温合成与发光性能

以介孔二氧化硅MCM-41为硅源,采用低温水热反应与后续煅烧相结合的方法合成Sr2-xZnSi2O7∶xEu3+红色荧光粉。实验结果表明,150℃水热处理16 h后的反应产物含Sr2ZnSi2O7相,经后续950℃煅烧3h得到Sr2ZnSi2O7纯相。在392 nm近紫外光的有效激发下,Sr2-xZnSi2O7∶xEu3+荧光粉显示Eu3+离子的特征跃迁发射,以615 nm的5D0→7F2跃迁发射峰为最强。适量Eu3+的掺杂对Sr2ZnSi2O7相结构几乎没有影响,当Eu3+离子的掺杂量x=0.10时,荧光粉发光强度最大。     

Ba_2B_2P_2O_(10):Eu~(3+)材料的光谱特性

采用高温固相法合成了Ba2B2P2O10:Eu3+材料,并研究了材料的光谱特性。在400nm近紫外光激发下,材料的发射光谱由4组线状峰组成,峰值分别为600,618,627和660nm,分别对应Eu3+的5D0→7F1,7F2,7F3和7F4跃迁。研究了Eu3+掺杂浓度及电荷补偿剂对材料发射强度的影响,结果显示,随Eu3+掺杂浓度的增大,材料的发射强度增大,并未出现浓度猝灭效应,同时,添加电荷补偿剂可增强材料的发射强度。     

Bi3+掺杂对Sr2MgSi2O7:Eu2+荧光粉的结构及发光性能的影响

采用溶胶-凝胶法在还原气氛下制备了Sr2MgSi2O7∶Eu2+,xBi3+(x=0,0.02,0.04,0.06,0.08,0.1)荧光粉,并用XRD、TG-DTA及激发与发射谱仪对样品的结构及发光性能进行了表征.结果发现:单掺杂Bi3+的Sr2MgSi2O7样品的发射光谱所用的材料的激发光谱为一主峰为286 nm的宽带谱,这是由于激发态时Bi3+的3p1→1S0电子能级跃迁而造成的;单掺杂Eu2+的Sr2MgSi2O7样品的发射光谱所用的材料的激发光谱为一主峰为358 nm的宽带谱,这是典型的Eu2+的4f65d3→4f7跃迁而引起的.当Bi3+离子掺杂到Sr2MgSi2O7∶Eu2样品的摩尔分数为0.04时,样品的发射强度是未掺杂Bi3离子样品的1.9倍.     

共掺Mo6+离子的Ca4LaNbW4O20∶Eu3+荧光粉的发光特性

采用高温固相法制备了红色荧光粉Ca4LaNb(W1-x Mo x)4O20∶Eu3+并研究了样品的发光性质。Ca4LaNbW4O20∶Eu3+的激发光谱中包含一个宽的激发带,峰值位于275 nm,归属于WO2-4基团的电荷迁移跃迁。随着Mo6+离子的掺入,Ca4LaNbW4O20∶Eu3+位于275 nm处的吸收带变宽,其原因是O2--Eu3+的电荷迁移跃迁增强。在Ca4LaNb(W1-x Mo x)4O20∶Eu3+的发射光谱中,400~500 nm间较宽的发射带属于WO2-4基团的发射带,而位于591 nm和616 nm的尖锐的发射峰分别属于Eu3+的5D0→7F1磁偶极跃迁和5D0→7F2电偶极跃迁发射。随着Mo6+离子浓度的增加,WO2-4基团的发射带强度下降,从而提高了色纯度。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.