Characterizing TiO2(110) surface states by their work function

The unreconstructed TiO(2)(110) surface is prepared in well-defined states having different characteristic stoichiometries, namely reduced (r-TiO(2), 6 to 9% surface vacancies), hydroxylated (h-TiO(2), vacancies filled with OH), oxygen covered (ox-TiO(2), oxygen adatoms on a stoichiometric surface) and quasi-stoichiometric (qs-TiO(2), a stoichiometric surface with very few defects). The electronic structure and work function of these surfaces and transition states between them are investigated by ultraviolet photoelectron spectroscopy (UPS) and metastable impact electron spectroscopy (MIES). The character of the surface is associated with a specific value of the work function that varies from 4.9 eV for h-TiO(2), 5.2 eV for r-TiO(2), 5.35 eV for ox-TiO(2) to 5.5 eV for qs-TiO(2). We establish the method for an unambiguous characterization of TiO(2)(110) surface states solely based on the secondary electron emission characteristics. This is facilitated by analysing a weak electron emission below the nominal work function energy. The emission in the low energy cut-off region appears correlated with band gap emission found in UPS spectra and is attributed to localised electron emission through Ti(3+)(3d) states.     

A clean, well-defined solid system for photosensitized 1O2 production measurements

Generation of singlet molecular oxygen ((1)O(2)) by photosensitization with methylene blue (MB) supported in Nafion-Na films has been quantified by integration of the (1)O(2) emission decay at 1270 nm. The quantum yield of (1)O(2) production (Phi(Delta)) in the air-equilibrated solid phase is 0.24 +/- 0.03. Information on the (1)O(2) generation environment has been gained from complementary techniques such as UV-Vis absorption and emission spectroscopy, as well as MB fluorescence and triplet-triplet absorption decay. Results are compared with the (1)O(2) generation by MB in methanol solution (Phi(Delta) = 0.51) and in methanol-swollen Nafion films (Phi(Delta) = 0.49 +/- 0.06). Differences and similarities are discussed in terms of the factors that influence Phi(Delta) in solution and in the solid media. The optical and mechanical features of Nafion, ease of dye loading, compatibility with most solvents, homogeneity, reproducibility and stability of the photosensitizing material makes it a convenient reference for (1)O(2) generation quantum yield measurements in transparent (micro)heterogeneous and homogeneous media.     

Robust Ethylenedioxythiophene–Vinylene Oligomers from Fragile Thiophene–Vinylene Cores: Synthesis and Optical,Chemical and Electrochemical Properties of Multicharged Shapes

Oligomers of ethylendioxythiophene–vinylene have been prepared. Their optical, electrochemical and chemical properties have been studied in detail by absorption and emission spectroscopy as well as cyclic voltammetry, Raman techniques and spectroelectrochemistry complemented with quantum chemical calculations. A comparison with their non‐ethylendioxy and non‐vinylene parents has been done. The inclusion of the EDO plus the vinylene function generates more robust electronic ground states regarding the largely flexible thiophene–vinylene (n TV) oligomeric homologues. The redox features of the new compounds are also rich of oxidative processes arising as an interesting stabilising balance effect between the oxygen fragment in the EDO groups (mesomeric effect) and the linear π‐conjugated structure. The oxidised species have been characterised, which show the ability for the formation of mixed valence charge‐transfer complexes and π dimers of different oxidation states, in particular, in the electrochemical medium, resulting that the electrochemical response is accounted for a succession of aggregation and electron‐transfer steps. With this work, a full understanding of the optical and electronic properties of these new oligomers in the context of the oligomer approach has been proposed.     

Thermal analysis and vapour pressure of a new series of tungsten(VI) oxo-alkoxide-β-ketoesterate complex precursors for the chemical vapour deposition of tungsten oxide

A new series of tungsten complexes, tungsten(VI) oxo-alkoxide-β-ketoesterate complexes have been synthesized and characterized by infrared and NMR spectroscopy. Thermogravimetric analysis has been carried out on the complexes as a function of temperature, and isothermally as a function of time. Based on the thermal analysis data, these complexes are evaluated for their suitability as precursors for the chemical vapour deposition of tungsten oxide thin films. The vapour pressure of these precursors is estimated using the Langmuir equation.     

Tuning the work function of ultrathin oxide films on metals by adsorption of alkali atoms

We report a theoretical investigation of the adsorption of alkali metal atoms deposited on ultrathin oxide films. The properties of Li, Na, and K atoms adsorbed on SiO(2)/Mo(112) and of K on MgO / Ag(100) and TiO(2)/Pt(111) have been analyzed with particular attention to the induced changes in the work function of the system, Phi. On the nonreducible SiO(2) and MgO oxide films there is a net transfer of the outer ns electron of the alkali atom to the metal substrate conduction band; the resulting surface dipole substantially lowers Phi. The change in Phi depends (a) on the adsorption site (above the oxide film or at the interface) and (b) on the alkali metal coverage. Deposition of K on reducible TiO(2) oxide films results in adsorbed K(+) ions and in the formation of Ti(3+) ions. No charge transfer to the metal substrate is observed but also in this case the surface dipole resulting from the K-TiO(2) charge transfer has the effect to considerably reduce the work function of the system.     

Imaging of atomic layer deposited (ALD) tungsten monolayers on alpha-TiO2(110) by X-ray standing wave Fourier inversion

A single atomic layer of tungsten grown by atomic layer deposition (ALD) on a single-crystal rutile TiO2(110) support is studied by the X-ray standing wave (XSW) technique. The surface structural and chemical properties were also examined using atomic force microscopy, X-ray photoelectron spectroscopy, and low-energy electron diffraction. The XSW measured set of hkl Fourier components for the W atomic distribution function are summed together to produce a model-independent 3D map of the W atoms relative to the rutile lattice. The 3D atomic image shows surface tungsten atoms equally occupying the two nonequivalent Ti sites with a slight outward displacement. This corresponds to the atop and bridge sites with respect to the underlying lattice oxygen atoms. These XSW measurements clearly show that ALD conformal layers can be highly coherent with respect to the substrate lattice.     

Spectroscopic studies of molybdenum and tungsten enzymes

Molybdenum and tungsten are the only second and third-row transition elements with a known function in living systems. Molybdenum fulfills functional roles in enzyme systems in almost all living creatures, from bacteria through plants to invertebrates and mammals, while tungsten takes the place of molybdenum in some prokaryotes, especially the hyperthermophilic archaea. The enzymes contain the metal bound by an unusual sulfur-containing cofactor. Despite possessing common structural elements, the enzymes are remarkable in the range of different chemical reactions that are catalyzed, although almost all are two-electron oxidation–reduction reactions in which an oxygen atom is transferred to or from the molybdenum. The functional roles filled by molybdenum enzymes are equally diverse; for example, they play essential roles in microbial respiration, in the uptake of nitrogen in green plants, in controlling insect eye color, and in human health. Spectroscopic studies, in particular electron paramagnetic resonance and X-ray absorption spectroscopy, have played an essential role in our understanding of the active site structures and catalytic mechanisms of the molybdenum and tungsten enzymes. This review summarizes the role spectroscopy has played in the state of our knowledge of the molybdenum and tungsten enzymes, with particular regard to structural information on the molybdenum sites.     

Activation of Oxygen on Gold and Silver Nanoparticles Assisted by Surface Plasmon Resonances

Surface plasmon resonances (SPRs) have been found to promote chemical reactions. In most oxidative chemical reactions oxygen molecules participate and understanding of the activation mechanism of oxygen molecules is highly important. For this purpose, we applied surface‐enhanced Raman spectroscopy (SERS) to find out the mechanism of SPR‐assisted activation of oxygen, by using p‐aminothiophenol (PATP), which undergoes a SPR‐assisted selective oxidation, as a probe molecule. In this way, SPR has the dual function of activating the chemical reaction and enhancing the Raman signal of surface species. Both experiments and DFT calculations reveal that oxygen molecules were activated by accepting an electron from a metal nanoparticle under the excitation of SPR to form a strongly adsorbed oxygen molecule anion. The anion was then transformed to Au or Ag oxides or hydroxides on the surface to oxidize the surface species, which was also supported by the heating effect of the SPR. This work points to a promising new era of SPR‐assisted catalytic reactions.     

Chemical and electrochemical treatment effects on the morphology,structure, and electrochemical performance of carbon fiber with different graphitization indexes

The association of capacitive charging of the double-layer and a faradic redox reaction is desirable on carbon fiber (CF) when oxygen functional groups or other heteroatoms are present on its surface enhancing its capacitive properties. In this work, a systematic study of carbon fiber produced at three different heat treatment temperatures (HTT) of 1000, 1500, and 2000 °C was performed upon two approaches: middle (chemical) and severe (electrochemical) oxidative treatments. Morphological, structural, and surface chemical changes were investigated by field emission gun-scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy. Electrochemical responses were analyzed by galvanostatic charge/discharge, electrochemical impedance spectroscopy, and cyclic voltammetry. Raman results showed that the electrochemical oxidation promoted structural variation on CF samples independently of their HTT. Concerning the specific capacitance, the results indicated that chemical treatment was more effective for CF1000 than those for CF1500 and CF2000. This behavior may be attributed to higher amount of oxygen on its surface as well as its lower structural ordering. Otherwise, for CF1000, the electrochemical treatment increased its resistivity. However, for CF1500 and CF2000, which present higher graphitization levels and less heteroatom contents, greater capacitance values were observed after their electrochemical oxidative treatment.     

Influence of oxygen plasma treatment on poly(ether sulphone) films

Poly(ether sulphone) (PES) is one of the most widely used materials in the micro-electronics industry and a good candidate for the substrates of flexible optoelectronic devices. In this work, the influences of oxygen plasma treatment on the surface chemical composition, surface morphology and optical transparency of PES films were investigated by means of X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM) and UV-visible spectrophotometry. The possible relations between the optical transparency of the substrate and the surface roughness and chemical composition were also studied. The oxygen plasma treatment seriously changed the surface chemical composition and made the surface more rough. Considerable amounts of sulphate species were found on the plasma-treated surface and the surface roughness values (R_a) increased monotonically with the increase of the treatment time. The PES films treated by 5 min, 15 min, 30 min and 45 min oxygen plasma demonstrated transmission of approximately 98, 94, 68 and 46%, respectively, in the wavelength range of 400-780 nm. The oxygen plasma induced decline of optical transparency of PES films might be attributed to both the increase of surface roughness and the changes of chemical composition of the film surface.     

Synthesis of GaN nanotip triangle pyramids on 3C-SiC epilayer/Si substrates via an in situ In-doping technique

GaN nanotip triangle pyramids were synthesized on 3C-SiC epilayer via an isoelectronic In-doping technique. The synthesis was carried out in a specially designed two-hot-boat chemical vapor deposition system. In (99.999%) and molten Ga (99.99%) with a mass ratio of about 1:4 were used as the source, and pieces of Si (111) wafer covered with 400-500 nm 3C-SiC epilayer were used as the substrates. The products were analyzed by x-ray diffraction, field emission scanning electron microscopy, high-resolution transmission electron microscopy, selected area electron diffraction, Raman spectroscopy, and photoluminescence measurements. Our results show that the as-synthesized GaN pyramids are perfect single crystal with wurtzite structure, which may have potential applications in electronic/photonic devices.     

In situ growth of epitaxial cerium tungstate (100) thin films

The deposition of ceria on a preoxidized W(110) crystal at 870 K has been studied in situ by photoelectron spectroscopy and low-energy electron diffraction. Formation of an epitaxial layer of crystalline cerium tungstate Ce(6)WO(12)(100), with the metals in the Ce(3+) and W(6+) chemical states, has been observed. The interface between the tungsten substrate and the tungstate film consists of WO suboxide. At thicknesses above 0.89 nm, cerium dioxide grows on the surface of Ce(6)WO(12), favoured by the limited diffusion of tungsten from the substrate.     

一种新的WO3纳米管的制备方法

一维纳米材料因可用来构造高性能纳米器件的结构单元而成为纳米材料研究的热点．目前的研究重点集中在材料的制备和结构性能表征方面,已发展了多种制备方法,主要有模板法、V-L-S法、L-L-S法和V-S法等,其中阳极氧化铝(AAO)模板法是制备一维材料的好方法．AAO模板的制备工艺已相当成熟,     

The effect of tungsten coating on the properties of diamond thick films

According to the physical properties of pure tungsten and tantalum and their carbides, a layer of tungsten thin films coating three tantalum filaments at a current of 750 A was prepared by us for the first time and called tungsten coating. Diamond thick films were deposited in a hot filament chemical vapor deposition (HFCVD) reactor using tantalum filaments before and after tungsten coating, respectively. The success of tungsten coating is verified by scanning electron microscopy examination of these filaments. The remarkable discrepancies in thermal conductivity, colors of diamond thick films, and electron dispersion spectroscopy of the films substantiate the success of tungsten coating, too. The effects of tungsten coating on the quality of diamond films were finally evaluated by Raman spectra. The text was submitted by the authors in English.     

Scanning work function microscopy

When a sample is locally excited with a highly focused raster-scanned beam of keV electrons, the variations DeltaPhi of the work function across the surface can be monitored from the shift of the onset energy for secondary electron emission along a fixed energy scale. The performance of that "onset" technique of work function microscopy and its incorporation into scanning Auger microprobes is described. The potentialities of this extremely surface sensitive technique for structural and chemical microanalysis are demonstrated by different experimental examples comprising work function analysis of surface reactions, and sputter depth profiling with in-situ Auger and work function spectroscopy. Scanning work function microscopy for surface microanalysis is shown to supply a lateral resolution down to the 10 nm range with a detection limit below 10(-2) of a monolayer.     

ESCA study of fractional monolayer quantities of chemisorbed gases on tungsten

X-ray photoelectron spectroscopy (ESCA) has been used in a study of CO and O₂ chemisorbed on a polycrystalline tungsten sample. Working under ultra-high vacuum conditions, the surface was cleaned and then covered with known monolayer and fractional monolayer quantities of adsorbed CO and O₂. The O(ls) and C(ls) spectral features were detected, and the influence of an adsorbed layer on the tungsten spectral features was determined. A chemical shift of 3.4 eV in the O(ls) line from chemisorbed CO is related to the different modes of bonding of CO to tungsten. A model calculation of the photoelectron yields expected from an adsorbed monolayer is in good agreement with the experimental results.     

Effects of vacuum annealing on the particle size and phase composition of nanocrystalline tungsten carbide powders

The effects of the vacuum annealing temperature (400–1400°C) on the phase and chemical composition, particle size, and microstresses of the nanocrystalline powders of tungsten carbide WC with 20–60 nm particles were studied by X-ray diffraction and electron microscopy. Vacuum annealing of WC nano-powders at T _ann ≤ 1400°C was accompanied by decarbonization, resulting from the interaction of carbon with the oxygen impurity. Changes in the chemical composition of the nanocrystalline powder of tungsten carbide led to changes in its phase composition. The annealing was accompanied by growth of powder particles due to the aggregation of nanoparticles and by a decrease of microstresses.     

Aggregation of photolytic gold nanoparticles at the surface of chitosan films

Formation and aggregation of photolytic gold nanoparticles at the surface of chitosan (CTO) films have been investigated. When thin films of chloroauric acid salt of CTO were irradiated with UV light in wet air at room temperature for 10 min, gold nanoparticles of approximately 10 nm size are formed at the film surface. Detailed X-ray photoelectron spectroscopy (XPS) study and field emission type scanning electron microscopy (FE-SEM) observation have been carried out to characterize gold nanoparticles at the film surface. The shift of Au(4f) peak to the higher energy side and broadening of full width at half-maximum in the XPS spectrum are the direct evidence of the existence of gold atoms and small clusters in the early stage of photolysis. According to FE-SEM observation, growth in the particle diameter and aggregation of nanoparticles were observed after prolonged irradiation, and, finally, the film surface was densely covered with gold particles of 20-100-nm size. Gold atoms and clusters could move in the film and precipitate to the irradiated surface. Chemical composition analysis further suggests that gold particles at the surface are covered with an ultrathin CTO layer, which is partly oxidized by oxygen and chlorinated by chlorine during photochemical reactions.     

Photophysical properties of N-acetyl-menthyl anthranilate.

The results of a comprehensive investigation of the photophysical properties of the sunscreen analogue, N-acetyl menthyl anthranilate (NAMA), in various solvent systems are reported. Luminescence studies reveal that this compound is fluorescent (Phi(f)=0.16+/-0.01) in toluene and has a solvent dependent emission maximum in the range 363-370 nm. Phosphorescence has also been detected in low temperature glasses with an emission maximum at 420 nm in EPA, and a lifetime of 1.3 s; the triplet energy was found to be 311+/-3 kJ mol(-1). Kinetic UV-visible absorption measurements revealed a transient species with absorption maxima at 450 nm and solvent dependent lifetimes of 120-240 micros which are attributed to the triplet state. The triplet state is efficiently quenched by oxygen, leading to the formation of singlet oxygen in all of the solvent systems studied. The singlet oxygen quantum yields (Phi(Delta)), determined by time-resolved near-infrared luminescence measurements, were in the range 0.19-0.21.     

Electron transfer from aromatic amino acids to triplet quinones

The photoreduction of 1,4-benzoquinone, 1,4-naphthoquinone, 9,10-anthraquinone (AQ) and several methylated or halogenated derivatives in argon-saturated acetonitrile-water mixtures by indole, N-acetyltryptophan and N-acetyltyrosine was studied by time-resolved UV-vis spectroscopy using 20 ns UV laser pulses. The quinone triplet state is quenched by the aromatic amino acids and the rate constants are (1-5)x10(9)M(-1)s(-1). The semiquinone radical anion Q.(-) is the major observable transient after electron transfer from amino acids to the quinone triplet state. Termination of Q.(-) and amino acid derived radicals takes place in the mus-ms range. The effects of structure and other specific properties of quinones and amino acids are discussed. The radicals are subjects of intercept with oxygen, whereby hydrogen peroxide is eventually formed. The quantum yield of oxygen uptake Phi(-O2) as a measure of formation of hydrogen peroxide increases with increasing amino acid concentration, approaching Phi(-O2) for AQ in air-saturated solution.