退火温度对La3Ga5SiO14薄膜结构及表面形貌的影响

采用脉冲激光沉积技术在Si(100)衬底上制备了La3Ga5SiO14薄膜,并研究了不同的退火温度对薄膜结构和表面形貌的影响.衬底温度为室温时生长的薄膜经过800 ℃以上的高温退火后,由最初的无定形态转变为无规则取向的多晶结构.衬底温度为400 ℃时生长的薄膜经过800 ℃退火处理后呈现无序的多晶形态.当退火温度进一步升高至1000 ℃时,XRD图谱显示薄膜由最初的(220)和(300)两个结晶方向转变为以(200)和(400)为主要取向的多晶结构.表面形貌分析表明:衬底温度为400 ℃时,随着退火温度的升高,薄膜颗粒尺寸逐渐增大,表面无裂纹,而衬底温度为室温时生长的薄膜退火后则出现大量的裂缝、孔洞等缺陷.     

SiO2气凝胶纳米多孔结构的自组装过程模拟

基于分子动力学理论,模拟并计算了纳米多孔SiO2气凝胶的原子尺度模型和力学性能.SiO2气凝胶网络结构的自组装形成过程表明,当密度为0.078 g/cm3时,形成的结构以纳米团簇为主,难以形成连通的骨架结构;当密度为0.172 g/cm3及以上时,硅氧元素分布已扩展形成了连通的无定形骨架结构.通过对不同密度体系模型单轴施加应变并计算相应的应力值,得到应力-应变关系曲线,并依据弹性范围求得弹性模量.模拟结果表明,弹性模量与密度成一次线性关系,当气凝胶密度在0.078～0.443 g/cm3时,弹性模量为0.1265～0.7889 MPa.     

热退火对ZnO-SiO2复合薄膜的微结构及荧光特性的影响

采用脉冲激光沉积技术(PLD)在单晶Si衬底上制备了ZnO-SiO2复合薄膜.分别用SEM、XRD观察了样品在沉积态(300℃)及700℃和900℃下热退火后的形貌和结构.发现经700℃热处理后,样品中有第三相β-Zn2SiO4形成,经900℃热处理后的样品中硅锌矿型Zn2SiO4取代了β-Zn2SiO4成为第三相.研究了热退火处理前后样品的荧光特性变化,结果表明经700℃热处理后,荧光光谱与沉积态相比,紫外区域的发光强度有较大提高,可见光区域的宽带强度变弱;经900℃热处理后,紫外区域荧光强度与700℃处理相比略有减小,可见光发光带消失.     

不同晶型TiO2的制备与光催化性能研究

采用溶胶凝胶法,利用不同温度热处理制备了不同晶体结构的TiO2纳米晶.利用XRD、SEM、EDS、XPS等分析方法对样品的晶体结构、形貌、化学元素组成以及价态进行了表征.结果表明400 ℃、500 ℃热处理TiO2为锐钛矿晶型,600 ℃ 热处理为锐钛矿金红石混合晶型,700 ℃热处理为金红石晶型,单颗粒子呈现类似球形形貌.以罗丹明B为目标污染物,测试了样品的光催化性能,结果表明400 ℃热处理TiO2具有最高的光催化活性,3 h后对罗丹明B的降解率达到94.6;,其反应速率常数达到0.969 h-1.     

TiO2/SiO2纤维的表征及其光催化活性

本文采用溶胶-凝胶法及离心甩丝,以TiCl4为钛源、乙酰丙酮为螯合剂成功制备了TiO2/SiO2纤维,并采用XRD 、FE-SEM、FT-IR和DSC -TG等手段对样品结构和性能进行表征.结果表明掺入SiO2可以抑制TiO2晶粒长大和晶型转变,700℃热处理后,未掺SiO2和掺15wt; SiO2的样品晶粒大小分别为32.4 nm和7.6 nm.TiO2/SiO2纤维直径为10～20μm,且表面含有大量纳米气孔.以活性艳红X-3B溶液为降解对象,研究了掺杂量、热处理温度对纤维光催化活性的影响,表明最优的方案为掺15wt; SiO2、热处理制度为700℃/2 h.     

Bi1.7Pb0.3Sr2Ca2Cu3O10多晶制备工艺对其电学性能影响的研究

采用溶胶-凝胶法成功制备了Bi1.7Pb0.3Sr2Ca2Cu3O10(BPSCCO)粉末,通过优化制备工艺获得了电学性能优良,转变温度在114 K左右的Bi1.7Pb0.3Sr2Ca2Cu3O10多晶靶材.利用X射线衍射仪测试了样品的物相和结构,并利用四探针法测试了靶材的电阻-温度曲线.对比了不同螯合剂对溶胶-凝胶法制备BPSCCO多晶的影响,发现以葡萄糖酸为螯合剂克服了传统工艺周期长、pH难调控的缺点.在此基础上,探究了热处理工艺对Bi1.7Pb0.3Sr2Ca2Cu3O10多晶电学性能的影响,得到了其最适预烧温度(600 ～ 700℃)、烧结温度(820～830℃)及烧结时间(48 h).     

HNTs/SiO2复合气凝胶制备及其性能研究

采用正硅酸乙酯(TEOS)为硅原,以硅烷改性的埃洛石纳米管(HNTs)为增强相,利用CO2超临界干燥技术制备具有优良力学和隔热性能的HNTs/SiO2复合气凝胶.利用傅立叶红外光谱、扫描电镜、比表面积与孔径分析仪、万能试验机和导热率测量仪等手段对HNTs改性后的表面状态、HNTs/SiO2复合气凝胶的微观形貌、孔结构、力学和导热性能进行了测试分析.结果表明:改性后的HNTs均匀分散到二氧化硅气凝胶基体中,并与SiO2纳米颗粒实现良好的结合,HNTs/SiO2复合气凝胶呈三维网络结构,当HNTs含量为15wt;时,平均孔径为10.47 nm;随着HNTs含量的增加,复合气凝胶的力学性能不断增强,同时其导热系数也不断增大,当HNTs含量为15wt;时,HNTs/SiO2复合气凝胶的抗压强度为0.85 MPa,导热系数为0.024 W/mK.     

改性羟基磷灰石晶须牙科复合树脂材料的制备及研究

采用硅胶对制备的HAP晶须进行表面改性形成SiO2颗粒附着,然后以硅胶改性的HAP晶须为填料混合甲基丙烯酸酯制备复合树脂材料.二氧化硅对晶须改性是通过形成凝胶颗粒与晶须结合并通过热处理形成牢固的结合.通过XRD、FT-IR光谱和SEM以表征微结构、键性质以及表面相组成.结果表明:经硅胶改性的HAP晶须表面有SiO2小颗粒附着,随着煅烧温度的增加,SiO2颗粒的数量明显增多,尺寸有变大的趋势.复合树脂材料的弯曲强度随改性晶须煅烧温度的增加而增加,以600 ℃煅烧的改性晶须为原料制备的树脂样品,其弯曲强度最高,达到89.46 MPa.     

白光LED用铽铕共掺镓酸锌微晶玻璃的制备、结构与发光性能研究

采用溶胶-凝胶法制备了Tb3+/Eu3+共掺ZnGa2O4微晶玻璃,研究了热处理温度对材料显微结构的影响以及不同稀土离子掺杂材料的发光性能.结果表明干凝胶样品在800～900℃温度热处理后可得到透明的含尖晶石结构ZnGaO4微晶玻璃,在1000℃热处理时由于SiO2非晶基体晶化析出三方Zn2SiO4与六方SiO2晶相导致样品失透.在微晶玻璃中具有ZnGa2O4纳米晶到Tb3+与Eu3+的能量传递.在900℃热处理Tb3+/Eu3+∶ZnGa2O4微晶玻璃样品中,Tb3+与Eu3+分别发射绿光和红光,并与ZnGa2O4纳米晶发射的蓝光组合成近白光发射.     

LiAlO2衬底上ZnO薄膜的溶胶-凝胶法制备和表征

采用溶胶凝胶法在LiAlO2(302)衬底上制备了ZnO薄膜.用X射线衍射(XRD)和扫描电镜(SEM)对样品的结构和形貌进行了表征.XRD结果表明,随着热处理温度的升高(350℃、450℃、550℃、600℃、800℃),所得到的薄膜分别为单相ZnAl2O4(350℃),ZnAl2O4和ZnO的混合相(450℃)以及单相的ZnO(550℃、600℃、800℃),并且ZnO薄膜c轴择优取向的生长趋势随温度升高相应明显.SEM图像显示,随着热处理温度的升高,ZnO薄膜的粒径相应变大.     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

First-principles coexistence simulations of supercooled liquid silicon

We perform first-principles coexistence simulations of the low-density and the high-density phases of supercooled liquid silicon and find a negative slope for the coexisting line in the temperature-pressure plane. Electron density maps and electron-localization function plots of the two phases of silicon show marked differences. The calculated differences suggest more localized electrons in the low-density liquid compared to the high-density liquid, coming from an increased population of covalent bonds, which further explain the calculated negative slope in the two phase coexistence regime. This is consistent with the presence of a pseudo-gap in low-density liquid silicon, absent in the high-density liquid which shows a metallic behavior.     

Crystal structures of thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane

Structures of both thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane, ?C₆H₄?CH₂SCH₂?C₆H₁₀?CH₂SCH₂?, have been determined, wherecis andtrans refer to the attachments to the cyclohexane ring. Thecis form crystallizes in the monoclinic space groupP2₁/c witha=8.4299(11)Å,b=21.772(2)Å,c=8.9724(13)Å, β=116.574(11)^o, andZ=4. Thetrans isomer packs into the monoclinic space groupP2₁ witha=8.159(16)Å,b=10.185(5)Å,c=9.558(2)Å, β=112.435(18)^o, andZ=2. The cyclohexane ring of thecis isomer is in the chair conformation, while the cyclohexane of thetrans isomer is found in a twisted boat conformation.     

CTAB与SDBS对碳酸锶粒子生长形态调控及机理研究

以表面活性剂CTAB和SDBS为化学添加剂,采用化学共沉淀法对碳酸锶晶体的生长形态进行调控,成功地制备出了实心的树枝状和花瓣为空心的花状碳酸锶粉体,并用X射线衍射(XRD)、扫描电子显微镜(SEM)和傅里叶变换红外光谱(FT-IR)等分析手段对样品进行了表征;最后重点对化学添加剂可能产生的影响机理进行了初步的探讨.结果表明,CTAB和SDBS在晶体生长的过程中能起到显著的影响作用,两者对粒子分散性能的作用效果相反,而且后者对晶体(013)和(213)晶面表面能降低的贡献明显大于前者.     

Crystal structures of the cis and trans isomers of a tetrathia[3.3.3.3]cyclophane

Both the cis and trans isomers of 3,11,18,26-tetrathiatricyclo[26.2.2.1^5,9.2^13,16.1^20,24] hexatriaconta-5,7,9,20,22,24-hexene have been prepared and structurally characterized. Each of these centrosymmetric tetrathia dimers includes two cyclohexane rings in chair conformations with either 1,4-cis or 1,4-trans bonding and two meta-substituted benzene rings. The cis isomer packs into the monoclinic space group P2₁/a with a = 10.485(3)Å, b = 10.3956(18)Å, c = 14.1343(10)Å, = 105.200(13)°, Z = 2 and refined to an R factor of 0.046. The trans isomer crystallizes in the monoclinic space group P2₁/c with a = 10.7217(12)Å, b = 5.6797(7)Å, c = 25.415(5)Å, = 96.001(12)°, Z = 2 and refined to an R factor of 0.043. In the cis structure each benzene ring faces a cyclohexane ring while in the trans structure the cyclohexane rings face one another.     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

Synthesis and Crystal Structure of 5-[2-(6-bromonaphthalenyloxymethyl)]-3-(4-morpholinomethyl)-1,3,4-oxadiazole-2(3<Emphasis Type="Italic">H</Emphasis>)-thione

Abstract  The title compound, C₁₈H₁₈BrN₃O₃S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal] reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these angles which therefore play a role in stabilizing crystal packing. Graphical Abstract  Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C₁₈H₁₈BrN₃O₃S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

电沉积法制备ZnO纳米棒阵列及其发光特性

本文以掺F的SnO2导电玻璃为基板,以硝酸锌水溶液为电解液,采用三电极恒电位体系电沉积制备ZnO纳米棒阵列,系统考察了硝酸锌浓度和沉积电位等工艺参数对ZnO纳米棒阵列的微观形貌及其发光性能的影响规律.结果表明,硝酸锌浓度和沉积电位对纳米棒阵列的形貌有显著影响,控制适宜的工艺条件可以制备出直径分布均匀、结晶性好且纯度高的六方纤锌矿ZnO纳米棒阵列.荧光光谱分析表明,电沉积制备出的ZnO纳米棒阵列在385 nm附近有一个强荧光发射峰,且发光性能稳定、对纳米棒阵列微观形貌的细微变化不敏感,使其在发光二极管和激光器等领域具有广阔的应用前景.     

Crystal structure of irisolidone from the flowers of Pueraia lobata

Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P2₁/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure.