氧化石墨烯浓度对还原氧化石墨烯/ZnS电化学性能的影响

以氧化石墨烯(GO)、乙酸锌(Zn(CH₃COO)₂)和硫脲为原料,采用水热法成功制备了还原氧化石墨烯/ZnS(rGO/ZnS)复合材料,并将该材料用作锂离子电池负极。高导电性的 rGO可以为锂离子和电子的传输提供有效的路径,ZnS可以提供较高的理论比容量。rGO/ZnS复合材料在rGO与纳米级高度分散的类球形ZnS颗粒协同作用下展现了较好的嵌锂容量和循环性能。当GO质量浓度为2 mg·mL^-1时制备的rGO/ZnS复合材料的倍率性能最好,循环稳定性最佳。     

废旧锂离子电池基石墨烯/聚苯胺复合材料制备及其电化学性能研究

以废旧手机锂离子电池回收的负极石墨粉制备的氧化石墨烯(GO)和苯胺单体为原料,利用GO活化H_2O_2产生的·OH为氧化剂,采用原位复合法制备了不同质量比的石墨烯/聚苯胺复合材料,通过FTIR、XRD和SEM对其进行了表征,并利用循环伏安、交流阻抗、恒电流充放电等对其电化学性能进行测试。结果表明,该类石墨烯/聚苯胺复合材料具有良好的电化学性能,当电流密度为100mA/g时,质量比为1∶10制备的石墨烯/聚苯胺复合材料(rGO/PANI-10)的比电容达到481F/g,较石墨烯比容量(161F/g)提高了199%,较聚苯胺比容量(351F/g)提高了37%;在500mA/g电流密度下,rGO/PANI-10充放电循环1000圈后,电容保持率为77%,表现出较好的循环稳定性。     

石墨烯/多孔纳米硅负极的电化学性能

采用酸浸蚀Al-Si合金的方法制备了多孔纳米Si,并用其制作以石墨烯为导电材料的石墨烯/多孔纳米Si负极. SEM和TEM的分析表明两者混合均匀. 作为锂离子电池的负极,该电极在1 mol•L^-1 LiPF₆/EC(碳酸乙烯酯):DMC(碳酸二甲酯) = 1:1(by volume) + 1.5%(by mass)VC(碳酸亚乙烯酯)溶液中、0.5 A•g^-1电流密度下,第120周循环的放电比容量为1842.6 mAh•g^-1,充放电效率为98.6%. 石墨烯的加入不仅提高了电极的导电性,而且减缓了充放电过程中电极多孔纳米结构的衰变.     

还原氧化石墨烯/碳纳米管/Co_3O_4三元复合材料的制备与电化学性能

将低温水热反应和低温热处理相结合,制备了含还原氧化石墨烯(RGO)、碳纳米管(CNTs)和Co3O4的三元纳米复合材料RGO-CNTs-Co3O4;利用X射线衍射仪、扫描电子显微镜、透射电子显微镜分析了合成产物的相组成和微观结构,分析了其形成过程;并利用电化学测试装置测定了其作为锂离子电池负极材料的电化学性能.结果表明,在合成反应过程中,氧化石墨烯被还原剂肼还原为石墨烯,同时在石墨烯和CNTs表面生成氢氧化钴;再经低温热处理得到RGO-CNTs-Co3O4三元复合材料.Co3O4纳米颗粒均匀分散在由RGO片层和CNTs组成的三维网络结构中;这种三维网络结构既有利于电子和离子的传输,又能够有效抑制Co3O4在脱嵌锂过程中因体积变化引起的结构破坏.总体而言,合成的新型三元复合材料具有高的比容量以及良好的循环性能与倍率性能.     

WO_3纳米棒/石墨烯复合材料的制备及电化学储锂性能

以氯化钨和氧化石墨烯(GO)为原料,乙醇为溶剂,一步合成了WO3纳米棒/石墨烯纳米复合材料(WO3/RGO).将WO3/RGO纳米复合材料用于锂离子电池负极,并通过充放电测试、循环伏安(CV)和电化学阻抗谱(EIS)技术综合考察了该材料的储锂性能.结果显示,在0.1C(1C=638 mA?g-1)倍率下,复合物的首次放电比容量达到761.4 mAh?g-1,100次循环后可逆容量仍保持在635 mAh?g-1,保持率为83.4%.即使在5C倍率下容量仍高达460 mAh?g-1.由此说明,WO3/RGO纳米复合物具有优异的循环稳定性及倍率性能,可望用于高性能锂离子电池.     

还原氧化石墨烯/TiO2复合材料在钠离子电池中的电化学性能

二氧化钛(TiO₂)作为有前景的钠离子电池负极材料, 具有良好的循环稳定性, 但由于其导电率较低, 而导致容量和倍率性能不佳限制了其实际应用. 本文采用喷雾干燥技术制备了氧化石墨烯/纳米TiO₂复合材料(GO/TiO₂), 通过热处理获得还原氧化石墨烯/TiO₂复合材料(RGO/TiO₂). 电化学测试结果表明, 还原氧化石墨烯改性的RGO/TiO₂复合材料的电化学性能得到显著提升, RGO含量为4.0%(w)的RGO/TiO₂复合材料在各种电流密度下的可逆容量分别为183.7 mAh·g^-1 (20 mA·g^-1), 153.7 mAh·g^-1 (100 mA·g^-1)和114.4 mAh·g^-1 (600mA·g^-1), 而纯TiO₂的比容量仅为93.6 mAh·g^-1 (20 mA·g^-1), 69.6 mAh·g^-1 (100 mA·g^-1)和26.5 mAh·g^-1 (600mA·g^-1). 4.0%(w) RGO/TiO₂复合材料体现了良好的循环稳定性, 在100 mA·g^-1电流密度下充放电循环350个周期后, 比容量仍然保持146.7 mAh·g^-1. 同等条件下, 纯TiO₂电极比容量只有68.8 mAh·g^-1. RGO包覆改性极大提高了TiO₂在钠离子电池中的电化学嵌钠/脱钠性能. RGO包覆改性技术在改进钠离子电池材料性能中将有很好的应用前景.     

碳纳米管/氧化石墨烯/硫复合正极材料的制备及其电化学性能

以碳纳米管和氧化石墨烯(CNTs/GO)为主体材料, 通过化学还原法制备了CNTs/GO 负载硫的复合正极材料CNTs/GO/S. 扫描电子显微镜(SEM)及透射电子显微镜(TEM)测试表明, CNTs 均匀插层在GO片间, 从而形成三维多孔结构, 有利于电解液的浸润; 活性物质硫均匀地负载在CNTs/GO 表面. 电化学测试表明,CNTs/GO/S复合材料具有高的比容量和良好的循环稳定性: 在1C倍率电流密度下, 复合材料首次放电比容量高达904 mAh·g^-1, 经过50圈循环之后, 复合材料的比容量仍保持在578 mAh·g^-1.     

LiFeSO4F/石墨烯复合材料的制备与电化学性能

分别以FeSO4.H2O、FeSO4.4H2O和FeSO4.7H2O为原料与LiF在四甘醇介质中反应制得LiFeSO4F,用X射线衍射(XRD)、扫描电镜(SEM)和透射电镜(TEM)表征LiFeSO4F的结构和形貌.热重分析表明LiFeSO4F在400℃开始分解.XRD结果表明,以FeSO4.4H2O和FeSO4.7H2O为原料,多个结晶水的存在可以延缓原料的脱水过程,有利于消除产物中FeSO4杂相的生成.利用循环伏安(CV)、电化学交流阻抗(EIS)和充放电实验测试材料的电化学性能,发现加入石墨烯后可以促进LiFeSO4F的电化学活性,提高材料的比容量、倍率性能和循环性能.     

石墨烯掺杂LiFePO4电极材料的合成及其电化学性能

采用水热辅助法合成石墨烯改性的LiFePO4多孔微球电极材料.并对材料进行了X射线衍射(XRD),扫描电子显微镜(SEM),透射电子显微镜(TEM),傅里叶变换红外(FT-IR)光谱,充放电等表征.从结果可以看出在2 mol·L-1LiNO3电解液体系中单纯包碳的LiFePO4微球在1C、50C倍率时的比容量分别为137、64 mAh·g-1,而石墨烯改性的LiFePO4微球的比容量分别为141、105 mAh·g-1,表现出较好的倍率特性.恒流循环充放电测试60次后两种材料容量保持率分别为70.2％、83.7％.说明掺杂石墨烯构成的三维导电网络能明显改善LiFePO4的电化学性能.     

Mn3O4/石墨烯复合材料的制备与电化学性能研究

本文以氧化石墨烯（GO）溶液为氧化剂,采用水热法使GO直接氧化Mn(Ac)₂制备Mn₃O₄/石墨烯复合材料,并通过在制备过程中加入氨水提高了复合材料中GO的还原程度与Mn₃O₄颗粒的分散性. 制得的Mn₃O₄/石墨烯复合材料表现出优异的电化学性能. 在0.5 A·g^-1的电流密度下复合材料质量比容量可达到850 mAh·g^-1,0.5 A·g^-1时充放电循环测试200周容量保持率为99%.     

还原氧化石墨烯表面聚苯胺纳米阵列的制备及电化学电容性能

本文以阳极氧化铝(AAO)膜为模板,通过恒电位法在自组装还原氧化石墨烯(rGO)膜表面制备有序聚苯胺(PANI)纳米线阵列。通过拉曼光谱和场发射扫描电子显微镜分别对其结构和微观形貌进行了表征,并对PANI纳米线阵列的电化学电容性能进行了测试。结果表明,rGO膜表面可电沉积PANI,电沉积得到的PANI纳米线阵列具有比PANI薄膜材料更高的电容和比电容。     

Synthesis of iron oxide cubes/reduced graphene oxide composite and its enhanced lithium storage performance

Fe₃O₄ is considered as a promising electrode material for lithium-ion batteries(LIBs) due to its low cost and high theoretical capacity(928 mAh/g).Nevertheless,the huge volume expansion and poor conductivity seriously hamper its practical applications.In this study,we use a facile hydrothermal reaction together with a post heat treatment to construct the three-dimensional heterostructured composite(Fe₃O₄/rGO) inwhich reduced graphene oxide sheets wraped the Fe₃O₄ submicron cubes as the conductive network.The electric conduction and electrode kinetics of lithium ion insertion/extraction reaction of the composite is enhanced due to the assist of conductive rGO,and thus the Listorage performance is obviously improved.The composite exhibits a reversible charge capacity of772.1 mAh/g at the current density of 0.1 A/g,and the capacity retention reaches 70.3% after400 cycles at0.5 A/g,demonstrating obviously higher specific capacity and rate capability over the Fe₃O₄ submicron cubes without rGO,and much superior cycling stability to the parent Fe_2 O_3 submicron cubes without rGO.On the other hand,as a synergic conductive carbon support,the flexible rGO plays an important role in buffering the large volume change during the repeated discharge/charge cycling.     

Graphene oxide assisted facile hydrothermal synthesis of LiMn0.6Fe0.4PO4 nanoparticles as cathode material for lithium ion battery

Assisted by graphene oxide（GO）,nano-sized LiMn0.6Fe0.4PO4 with excellent electrochemical performance was prepared by a facile hydrothermal method as cathode material for lithium ion battery.SEM and TEM images indicate that the particle size of LiMn0.6Fe0.4PO4（S2）was about 80 nm in diameter.The discharge capacity of LiMn0.6Fe0.4PO4 nanoparticles was 140.3 mAh-g^1 in the first cycle.It showed that graphene oxide was able to restrict the growth of LiMn0.6Fe0.4PO4 and it in situ reduction of GO could improve the electrical conductivity of LiMn0.6Fe0.4PO4 material.     

Artemisia herba-alba Asso eco-friendly reduced few-layered graphene oxide nanosheets: structural investigations and physical properties

Nowadays graphene is universally known as a promising material. Hence, the development of eco-friendly synthesis methods for this material is of great importance. This study reports on the bio-synthesis of graphene by a green chemistry process using Artemisia herba-alba Asso (AHAA) natural extract. Moreover, this work reports on the physical properties, including surface/interface and optical and electrical properties of the obtained graphene sheets. UV–VIS, Raman, XPS spectroscopies and TEM microscopy investigations confirmed the reduction, and the conversion of graphene oxide to few-layered reduced graphene oxide as well as the efficiency of this plant extract compared with several natural extracts and chemical agents. Furthermore, it was found that the optical and electrical properties of graphene can be modulated and controlled via this eco-friendly cost-effective process. Hence, AHAA can be an effective chelating agent to produce graphene sheets.     

ZnWO4 nanocrystals/reduced graphene oxide hybrids: Synthesis and their application for Li ion batteries

ZnWO4,as an environment-friendly and economic material,has the potential for Li ion batteries(LIB)application.In this paper,a facile method has been developed to synthesize ZnWO4supported on the reduced graphene oxide(RGO)to improve its LIB performance.The cuboid-like ZnWO4nanocrystals are prepared by directly adding Na2WO4 powders into the graphene oxide/Zn aqueous solution followed by a hydrothermal treatment.The high-resolution TEM,XRD and XPS characterizations were employed to demonstrate structural information of the as-prepared ZnWO4/RGO hybrids carefully.Besides,we also discussed the LIB properties of the hybrids based on the detailed galvanostatic charge-discharge cycling tests.As a result,the specific capacity of the as-prepared ZnWO4/RGO hybrids reached more than 477.3 mA h g 1after 40 cycles at a current density of 100 mA g 1(only less than 159 mA g 1for bare ZnWO4).During the whole cyclic process,the coulombic efficiency steadily kept the values higher than 90%.     

纳米纤维素/还原氧化石墨烯复合材料用于高性能超级电容器

以高浓度氧化石墨烯(GO)溶液作为反应前驱体,纳米纤维素(NC)作为物理间隔物和电解液储存器,通过简单的一步水热法制备了纳米纤维素/还原氧化石墨烯(NC/rGO)复合材料,并探究了其作为超级电容器电极材料的潜力。结果如下：NC添加量为1 mL所制备的NC/rGO-1具有最佳电化学性能。基于NC/rGO-1的无黏合剂对称型超级电容器在0.3 A·g^-1的电流密度下显示出了269.33 F·g^-1和350.13 F·cm^-3的高质量和体积比电容,并在10.0 A·g^-1时仍能达到215.88 F·g^-1和280.62 F·cm^-3(其初始值的80.15%)。组装器件还显示出了较高的质量和体积能量密度(9.3 Wh·kg^-1和12.13 Wh·L^-1)和出色的循环性能(10 A·g^-1下10 000次循环后其初始比电容仅减少6.02%)。     

Facile synthesis of Fe3O4/reduced graphene oxide/polyvinyl pyrrolidone ternary composites and their enhanced microwave absorbing properties

In this paper, ternary nanocomposites of Fe₃O₄/reduced graphene oxide/polyvinyl pyrrolidone (Fe₃O₄/rGO/PVP) as a novel type of electromagnetic microwave absorbing materials were synthesized by a three-step chemical approach. First, Fe₃O₄ nanospheres were made by solvent thermal method. Successively, the Fe₃O₄ particles were assembled with rGO after having activated by para-aminobenzoic acid. PVP grafting and reduction of GO happened simultaneously in the third step. It is found that the electromagnetic absorption (EA) performance of synthesized ternary composites with suitable PVP amount had been significantly enhanced comparing to Fe₃O₄ and Fe₃O₄/rGO. Merely 15?wt% low loading in paraffin and thin as 2.8?mm can reach effective EA bandwidth (below ?10 Db) of 11.2?GHz, and the highest reflection loss reached ?67?dB at 10.7?GHz. It was demonstrated that these composites show an effective route to novel microwave absorbing material design.     

纳米纤维素/还原氧化石墨烯复合材料用于高性能超级电容器

以高浓度氧化石墨烯(GO)溶液作为反应前驱体,纳米纤维素(NC)作为物理间隔物和电解液储存器,通过简单的一步水热法制备了纳米纤维素/还原氧化石墨烯(NC/rGO)复合材料,并探究了其作为超级电容器电极材料的潜力。结果如下：NC添加量为1 mL所制备的NC/rGO-1具有最佳电化学性能。基于NC/rGO-1的无黏合剂对称型超级电容器在0.3 A·g^-1的电流密度下显示出了 269.33 F·g^-1和 350.13 F·cm^-3的高质量和体积比电容,并在 10.0 A·g^-1时仍能达到 215.88 F·g^-1和 280.62 F·cm^-3(其初始值的 80.15%)。组装器件还显示出了较高的质量和体积能量密度(9.3 Wh·kg^-1和 12.13 Wh·L^-1)和出色的循环性能(10 A·g^-1下10 000次循环后其初始比电容仅减少6.02%)。     

A general approach for the growth of metal oxide nanorod arrays on graphene sheets and their applications

In the fabrication of flexible devices, highly ordered nanoscale texturing, such as semiconductor metal oxide nanorod arrays on flexible substrates, is critical for optimal performance. Use of transparent conducting films, metallic films, and polymer substrates is limited by mechanical brittleness, chemical and thermal instability, or low electrical conductivity, low melting point, and so on. A simple and general nanocrystal-seed-directed hydrothermal route has now been developed for large-scale growth of nanorod arrays of various semiconductor metal oxides (MO), including TiO(2), ZnO, MnO(2), CuO, and ZrO(2) on both sides of flexible graphene (G) sheets to form sandwichlike MO/G/MO heterostructures. The TiO(2)/G/TiO(2) heterostructures have much higher photocatalytic activity than TiO(2) nanorods, with a photocatalytic degradation rate of methylene blue that is four times faster than that of the TiO(2) nanorods, and are thus promising candidates for photocatalytic decontamination.