Comparison of hydroxypropyl and carboxymethyl guar for the preparation of nanocellulose composite films

The gas barrier and mechanical properties are crucial parameters for packaging materials, and they are highly correlated to the molecular interactions in the polymer matrix. To improve these properties of TEMPO-oxidized cellulose nanofibers (TOCNs) composite films, we studied the effect using hydroxypropyl guar (HPG) or carboxymethyl guar (CMG) in the preparation of TOCN composite films, which were made by following the solution-casting method. The subsequent film characterizations were carried out by UV–Vis spectra, scanning electron microscopy, oxygen and water vapor permeability measurements, tensile and thermogravimetric analyses. SEM results showed that CMG-based films had denser structures than their HPG counterparts. Moreover, the improved hydrogen bonding of the CMG-based films was partially responsible for the improved gas barrier performance, tensile strength and thermal stability. These results support the conclusion that CMG had advantages over HPG when used in the preparation of TOCNs packaging composite films.     

Effects of chain extender and uniaxial stretching on the properties of PLA/PPC/mica composites

Poly(lactic acid) (PLA)/poly(propylene carbonate) (PPC)/mica composites with different amount of chain extender (CE) were melt compounded and then processed via two routes (compression molding and uniaxial stretching) into sheets and films. The tensile, thermal, and oxygen barrier properties of all the samples were investigated. Tensile test showed that the tensile strength and elongation at break of all films were much higher than that of all sheets, especially for PLA/PPC/mica with 0.9‐wt% CE composite (CM₃(CE)_0.9) film. The crystallinity of all films increased significantly after uniaxial stretching of sheet samples. The Fourier transform infrared spectroscopy (FTIR) results proved the chemical reactions occurred between PLA/PPC and CE. Scanning electron microscope (SEM) analysis revealed that compatibility and interfacial adhesion of all samples were improved after adding mica and CE, and they were further enhanced after uniaxial stretching. The addition of CE was not favorable to improve the oxygen barrier performance of PLA/PPC/mica sheet samples. However, the oxygen barrier performance of film samples was significantly improved after uniaxial stretching. In particular, the CM₃(CE)_0.9 film had the lowest oxygen permeability coefficient (1.4 × 10^?15 cm³·cm/(cm²·s·Pa)), and this was the best oxygen barrier properties reported in the literature for PLA‐based composites, which was comparable with PA film. This study demonstrated the high efficiency of uniaxial stretching on improvement of properties of composites, which would promote the application of biodegradable polymers in oxygen sensitive food packaging.     

Preparation and Barrier Properties of Chitosan-Layered Silicate Nanocomposite Films

Summary: In this study, chitosan nanocomposite films were prepared using a solvent-casting method by incorporation of an organically modified montmorillonite (Cloisite 10A). The effect of filler concentration on the water vapor permeability, oxygen permeability, mechanical and thermal properties of the composite films was evaluated. The structure of nanocomposites and the state of intercalation of the clay were characterized by XRD. The water vapor permeability of pure chitosan films was measured as a function of relative humidity (RH). It was found that the permeability value increased with an increase in RH. The water vapor and gas permeability values of the composite films decreased significantly with increasing filler concentration. Permeation data was fitted to various phenomenological models predicting the permeability of polymer systems filled with nanoclays as a function of clay concentration and aspect ratio of nanoplatelets. According to the XRD results, an increase in basal spacing was obtained with respect to pure clay for chitosan/clay nanocomposites. This demonstrated the formation of intercalated structure of clay in the polymer matrix. Tensile strength and elongation at break of the composites increased significantly with the addition of clay, however the thermal and color properties of the films were not much affected by the intercalation of clay into polymer matrix.     

气相生长碳纤维/形状记忆聚氨酯复合薄膜的力学及形状记忆性能研究

采用溶液混合法制备了不同含量的气相生长碳纤维(VGCF)增强形状记忆聚氨酯(SMPU)的复合材料薄膜,测试分析了纯SMPU及VGCF/SMPU复合材料薄膜的力学性能及形状记忆性能.结果表明,制得的复合材料薄膜在VGCF含量达到9 wt%时,VGCF在SMPU基体中仍具有较好的分散性;SMPU与VGCF复合后,得到的复合材料薄膜的拉伸强度和刚度有较大程度的提高,含量达到9 wt%时复合材料薄膜的拉伸强度比纯SMPU提高66%,弹性模量提高300%,储能模量也有较大程度提高;SMPU与VGCF复合后,形状记忆性能有一定的下降,但经过适当预处理后,其形状记忆性能可以基本接近纯SMPU.     

Resin impregnation of cellulose nanofibril films facilitated by water swelling

Flexible composite films were produced by impregnating aqueous phenol formaldehyde (PF) resin into water-swollen cellulose nanofibril (CNF) films. CNF films were prepared using a pressurized filtration method in combination with freeze drying. The freeze-dried films were swollen with water then impregnated with PF resin by soaking in aqueous resin solutions of varying concentrations. Small amounts of PF slightly enhanced the tensile properties of CNF films. The formulation with the best mechanical properties was CNF/PF films with 8 wt % resin exhibiting tensile stress and toughness of 248 MPa and 26 MJ/m³, respectively. Resin concentrations higher than about 8 % resulted in composites with decreased tensile properties as compared to neat CNF films. The wet strength of the composite films was significantly higher than that of the neat CNF films. The resulting composites showed greater resistance to moisture absorption accompanied by reduced thickness swelling when soaked in water as compared to neat CNF films. The composites also showed decreased oxygen permeability at low humidity compared to neat films, but the composites did not show improved barrier properties at high humidity.     

氯化聚丙撑碳酸酯增容聚丙撑碳酸酯/秸秆粉复合材料的制备及性能

聚丙撑碳酸酯(PPC)是一种新型热塑性生物降解材料,但其热性能及力学性能较差,应用受到限制。以秸秆粉这种农作物副产品作为增强体改性PPC,既可以提高PPC的力学性能同时又可开发利用秸秆资源。氯化聚丙撑碳酸酯(CPPC)是聚丙撑碳酸酯(PPC)经过氯化得到的,对天然纤维表面具有良好的浸润性和粘结性。本文以CPPC为增容剂,通过熔融共混法制备了PPC/秸秆粉复合材料。采用扫描电子显微镜(SEM)、拉伸实验、动态力学性能测试(DMA)及转矩流变仪对复合材料的结构及性能进行了表征,重点考察了CPPC的添加量对复合材料力学和流变性能的影响。结果表明,当CPPC质量分数为1.8%时,可使添加质量分数为30%秸秆粉的PPC复合材料拉伸强度提高38%,模量提高30%。同时,CPPC的引入使复合材料的粘度下降,改善了PPC/秸秆粉复合材料的加工性能。因此,作为增容剂的CPPC为制备高性能PPC/天然纤维复合材料提供了新的解决办法。     

Preparation and Properties of Biodegradable Spent Tea Leaf Powder/Poly(Propylene Carbonate) Composite Films

The aim of the present work is to develop novel bio-based lightweight material with improved tensile and thermal properties. Spent tea leaf powder (STLP) was used as a filler to improve the tensile and thermal properties of polypropylene carbonate (PPC). Tea is an important material used in hotels and households, and spent tea leaf is a resulting solid waste. Composite films with STLP were obtained by the solution casting method. These films were characterized by optical and scanning electron microscopy, Fourier transform-infrared spectroscopy, thermogravimetric analysis, and tensile testing to examine the effect of filler content on the properties of the composites. The results showed that composite films have increased tensile strength due to enhanced interfacial adhesion between the filler and the matrix. In addition, the composite films also exhibited higher thermal degradation temperatures than pure polypropylene carbonate. The morphology results indicate that there is a good interface interaction between STLP and PPC. Results of the study reveal STLP to be a promising green filler for polymer plastics.     

Cold water fish gelatin films: Effects of cross-linking on thermal, mechanical, barrier, and biodegradation properties

Gelatin was extracted from Alaska pollock (Theragra chalcogramma) and Alaska pink salmon (Oncorhynchus gorbuscha) skins and cast into films. The fish gelatin films’ tensile, thermal, water vapor permeability, oxygen permeability, and biodegradation properties were compared to those of bovine and porcine gelatin films. In addition, fish gelatin films were cross-linked with glutaraldehyde. Pollock and salmon gelatin films had comparable tensile properties, but had lower tensile strength and percent elongation than mammalian gelatin films. The lower strength and elongation might have been due to lower structural gelatin levels present in fish gelatin films. The addition of cross-linkers had little effect on tensile properties and melting temperatures of fish gelatin films. Pollock gelatin films had the lowest water vapor and oxygen permeability values, whereas mammalian gelatin films had the highest permeability values. Cross-linking resulted in lower water vapor permeability for salmon gelatin films and higher oxygen permeability for pollock gelatin films. However, all fish gelatin films had better water vapor and oxygen barrier properties than mammalian gelatin films. Also, fish gelatin films degraded faster than mammalian gelatin films.     

紫外光固化的聚氨酯－丙烯酸酯－纤维素复合膜

再生纤维素膜(甘蔗渣浆制)表面直接用紫外光固化聚氨酯-丙烯酸酯制备出防水性复合膜。由红外光谱和扫描电镜研究了复合膜的结构。同时,测定了膜的防水性、力学性能、水汽透过性和尺寸稳定性。实验结果表明,当聚氨酯：丙烯酸酯为40:55(质量比),在400W紫外光下固化5min制得的复合膜具有致密的表面结构和较好的性能,该膜经水浸泡后其断裂强度可达干膜的90%,浸水收缩率和膨胀率均小于2.5%,水汽渗透量仅为再生纤维素膜的1/4.由此表明复合膜的防水性和尺寸稳定性明显提高。此外,该复合膜在可见光区的透光率在80%～90%之间,而且对紫外光有屏蔽作用。     

Structural interaction and gas barrier properties of ethylene‐vinyl alcohol/tin phosphate glass composites

The strength of interaction between tin phosphate glass (PGlass) filler droplets and an ethylene‐vinyl alcohol (EVOH) matrix were investigated by image, thermal, and rheological analysis. 10% PGlass droplets in EVOH were smaller than those previously observed in maleated polypropylene. Analysis using the Fox equation showed that EVOH/97 °C T_g PGlass composites are not miscible systems. Dynamic shear and extensional rheology data of those composites exhibited a weak physical network, with relaxation times longer than that of pure EVOH at all strain rates. The tensile properties of the EVOH/10 vol % PGlass composite showed it to be more ductile and flexible than a typical polymer/inorganic filler system, supporting interaction between PGlass and EVOH sufficient to interrupt polymer–polymer hydrogen bonding. While undrawn EVOH/PGlass composite films showed increased oxygen gas permeability when compared to undrawn neat EVOH film, the drawn composite films exhibited oxygen permeability 6–7 times lower than that of neat EVOH, attributed to the presence of high aspect ratio PGlass particles after orientation. The concept of hydrogen bonding between polymer and PGlass can likely be applied to other polymers such as polyamides which possess numerous hydrogen bonding sites. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 989–998     

Improved mechanical and barrier properties of PPC multilayer film through interlayer hydrogen bonding interaction

Poly(propylene carbonate) (PPC) is coated with cellophane (PT) via the intermolecular hydrogen bonds of chitosan (CS) with the both polymers, and their multilayer films are prepared in different weight ratios. The trace presence of chitosan on the surface of PT promotes the combination with PPC layers. After coating, the Young’s modulus and tensile strength of PPC are greatly improved, the storage modulus still keep a high value between ～0–70°C. The oxygen barrier of PPC is increased at least 580 times, and the multilayer films still keep good water vapor barrier in some degree.     

Preparation and Characterization of Polypropylene Carbonate Bio-Filler (Eggshell Powder) Composite Films

In recent years, biodegradable polymer composites have attracted considerable attention due to inadequate and depleting petroleum resources and to replace nonbiodegradable synthetic polymers posing environment problems. In the present work, biodegradable composites based on polypropylene carbonate (PPC)/eggshell powder (ESP) were prepared by the solution-casting method using chloroform as the solvent. Polypropylene carbonate was loaded with 1 to 5 wt% of eggshell powder (particle size < 40 µm). Characterization of the composites was accomplished by Fourier transform-infrared (FT-IR) spectroscopy, thermogravimetric analysis (TGA), and X-ray diffraction (XRD) analysis, and morphological studies were carried out by optical microscopy (OM) and scanning electronic microcopy (SEM). The tensile properties of the composite films were found to be higher than those of neat PPC matrix and increased with ESP content up to 4 wt.% and then decreased. This work offers an easy path to manufacture ecofriendly PPC/eggshell powder composite films with improved properties, and reducing, in some cases, the demand for petroleum-based plastics such as polyolefins.     

Preparation and characterization of modified graphite oxide/poly(propylene carbonate) composites by solution intercalation

Modified graphite oxide (MGO)/Poly (propylene carbonate) (PPC) composites with excellent thermal and mechanical properties have been prepared via a facile solution intercalation method. An intercalated structure of MGO/PPC composites was confirmed by X-ray diffraction and scanning electron microscope. The thermal and mechanical properties of MGO/PPC composites were investigated by thermal gravimetric analysis, differential scanning calorimetric, dynamic mechanical analysis, and electronic tensile tester. Due to the nanometer-sized dispersion of layered graphite in PPC matrix and the strong interfacial interaction between MGO and PPC, the prepared MGO/PPC composites exhibit improved thermal and mechanical properties in comparison with pure PPC. Compared with pure PPC, the MGO/PPC composites show the highest thermal stability and the T_g is 13.8 °C higher than that of pure PPC, while the tensile strength (29.51 MPa) shows about 2 times higher than that of pure PPC when only 3.0 wt.% MGO is incorporated. These results indicate that this approach is an efficient method to improve the properties of PPC.     

LDPE/EVA/graphene nanocomposites with enhanced mechanical and gas permeability properties

In the present work, graphene oxide (GO) and reduced graphene oxide (RGO) were incorporated at low‐density polyethylene (LDPE)/ethylene vinyl acetate (EVA) copolymer blend using solution casting method. Monolayer GO with 1‐nm thickness and good transparency was synthesized using the well‐known Hummers's method. Fourier transform infrared and X‐ray photoelectron spectroscopy data exhibited efficient reduction of GO with almost high C/O ratio of RGO. Scanning electron microscopy showed the well distribution of GO and RGO within LDPE/EVA polymer matrix. The integrating effects of GO and RGO on mechanical and gas permeability of prepared films were examined. Young's modulus of nanocomposites are improved 65% and 92% by adding 7 wt% of GO and RGO, respectively. The tensile measurements showed that maximum tensile strength emerged in 3 wt% of loading for RGO and 5 wt% for GO. The measured oxygen and carbon dioxide permeability represented noticeably the attenuation of gas permeability in composite films compared with pristine LDPE/EVA blend. Copyright © 2015 John Wiley & Sons, Ltd.     

Investigation of polyethylene‐grafted‐maleic anhydride presence as a compatibilizer on various properties of nanocomposite films based on polyethylene/ethylene vinyl alcohol/ nanoclay

High oxygen barrier films were prepared based on low‐density polyethylene (LDPE)/ethylene vinyl alcohol (EVOH)/ nanoclay and polyethylene‐grafted‐maleic anhydride (LDPE‐g‐MA) as a compatibilizer. Box–Behnken statistical experiment design methodology was employed to study the effects of nanoclay, LDPE‐g‐MA, and EVOH presence and their contents on various properties of the final films. The R² parameter varied between 0.89 and 0.99 for all the obtained responses. The morphology of the samples was evaluated. Results of oxygen transfer rate (OTR) test indicated that the addition of EVOH up to 30 wt% to neat LDPE can decrease oxygen permeability significantly. The addition of nanoclay also decreased the permeability of resulting films but, LDPE‐g‐MA reduced the permeability of the films only at an optimal content. Elastic modulus was increased with the addition of nanoclay, EVOH, and LDPE‐g‐MA to the matrix. An increase in EVOH content in the samples improved the tensile strength. Effect of nanoclay on tensile strength was highly dependent on the presence of a compatibilizer. The addition of compatibilizer to the samples and increasing its content enhanced the tensile strength of the specimens. Incorporation of nanoclay, EVOH, and LDPE‐g‐MA to the LDPE matrix and increasing the amount of these components in the samples led to higher storage modulus, zero shear rate viscosity, and shear thinning exponent, but, lowered the terminal slope and the frequency of intersection point of storage modulus (G′) and loss modulus (G″). The only exception was that EVOH increment resulted in a lower shear thinning exponent. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation and Properties of Poly（vinyl alcohol）/Chitosan Blend Bio-nanocomposites Reinforced by Cellulose Nanocrystals

The aim of this paper is to report the effect of the addition of cellulose nanocrystals（CNCs） on the mechanical, thermal and barrier properties of poly（vinyl alcohol）/chitosan（PVA/Cs） bio-nanocomposites films prepared through the solvent casting process. The characterizations of PVA/Cs/CNCs films were carried out in terms of X-ray diffraction（XRD）, transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, thermogravimetric analysis（TGA and DTG）, oxygen transmission rate（OTR）, and tensile tests. TEM and SEM results showed that at low loading levels, CNCs were dispersed homogenously in the PVA/Cs matrix. The tensile strength and modulus in films increased from 55.1 MPa to 98.4 MPa and from 395 MPa to 690 MPa respectively, when CNCs content went from 0 wt% to 1.0 wt%. The thermal stability and oxygen barrier properties of PVA/Cs matrix were best enhanced at 1.0 wt% of CNCs loading. The enhanced properties attained by incorporating CNCs can be beneficial in various applications.     

Thermal oxidative stability and effect of water on gas transport and mechanical properties in PA6‐EVOH films

The thermal oxidative stability and the effect of water on gas transport and mechanical properties of blends of polyamide 6 (PA6) with ethylene‐co‐vinyl alcohol (EVOH) and EVOH modified with carboxyl groups (EVOH‐COOH) have been investigated. The presence of EVOH reduces water vapor and oxygen gas permeability of polyamide, as well as small amounts of EVOH‐COOH further improve barrier properties, especially to oxygen. This has been explained in terms of improved interactions of the blend constituents in the amorphous phase, due to ionic linkages between the polyamide amino groups and the carboxyls of modified EVOH. The permeation to gases was found to increase with the amount of sorbed water. The morphology of the samples was found to have an effect on barrier properties, as the presence of EVOH causes the PA6 α crystalline form to increase, lowering the permeability to oxygen and water vapor. Mechanical properties are strongly affected by water sorption, as tensile modulus and strength decrease with increasing water content. Chemiluminescence (CL), infrared spectroscopy (FTIR), and tensile test were employed in order to assess the correlation between chemical composition and the thermal oxidative stability of the films aged at 110 °C in air. CL experiments suggest that the presence of EVOH and EVOH‐COOH efficiently inhibits the formation of peroxidized species during the processing, and increases the thermal oxidative stability of the films. Infrared spectroscopy showed a build‐up of carbonyl absorption in the range 1700–1780 cm^?1, due to the formation of oxidation products, which is greater in the case of the pure polymer. Tensile tests on films revealed a reduction in ductility as a result of ageing for neat PA6, whereas in comparison the blends exhibit a far better long‐term stability. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 840–849, 2007     

Strength and barrier properties of MFC films

The preparation of microfibrillar cellulose (MFC) films by filtration on a polyamide filter cloth, in a dynamic sheet former and as a surface layer on base paper is described. Experimental evidence of the high tensile strength, density and elongation of films formed by MFC is given. Typically, a MFC film with basis weight 35 g/m² had tensile index 146 ± 18 Nm/g and elongation 8.6 ± 1.6%. The E modulus (17.5 ± 1.0 GPa) of a film composed of randomly oriented fibrils was comparable to values for cellulose fibres with a fibril angle of 50°. The strength of the films formed in the dynamic sheet former was comparable to the strength of the MFC films prepared by filtration. The use of MFC as surface layer (0–8% of total basis weight) on base paper increased the strength of the paper sheets significantly and reduced their air permeability dramatically. FEG-SEM images indicated that the MFC layer reduced sheet porosity, i.e. the dense structure formed by the fibrils resulted in superior barrier properties. Oxygen transmission rates (OTR) as low as 17 ml m⁻² day⁻¹ were obtained for films prepared from pure MFC. This result fulfils the requirements for oxygen transmission rate in modified atmosphere packaging.     

Preparation and characterization of cellulose nanocomposite films with two different organo-micas

The mechanical properties, morphologies, and gas barriers of hybrid films of cellulose with two different organoclays are compared. Dodecyltriphenyl-phosphonium-mica (C₁₂PPh-mica) and hexadecyl-mica (C₁₆-mica) were used as reinforcing fillers in the fabrication of the cellulose hybrid films. The cellulose hybrid films were synthesized from N-methyl-morpholine-N-oxide (NMMO) solutions with the two organo-micas, and solvent-cast at room temperature under vacuum, yielding 15–20 μm thick films of cellulose hybrids with various clay contents. We found that the addition of only a small amount of organoclay is sufficient to improve the mechanical properties and gas barriers of the cellulose hybrid films. Even polymers with low organoclay contents (1–7 wt %) were found to exhibit much higher strength and modulus values than pure cellulose. The addition of C₁₂PPh-mica was more effective than that of C₁₆-mica with regards to the initial tensile modulus, whereas the addition of C₁₆-mica was more effective than that of C₁₂PPh-mica with regards to the gas barrier of the cellulose matrix. The intercalations of the polymer chains in the clays were examined with wide-angle X-ray diffraction (XRD) and electron microscopy (SEM and TEM).     

Properties of nitrocellulose‐coated and polyethylene‐laminated chitosan and whey films

Chitosan (chitosan acetic acid salt) and whey (65% protein) films were coated with a nitrocellulose lacquer or laminated with polyethylene to enhance their water resistance and gas barrier properties in humid environments. The barrier properties were measured by the Cobb₆₀ test and water‐vapor (100% relative humidity) transmission and oxygen (90% relative humidity) permeability tests. Mechanical properties were obtained with tensile tests. Packaging properties were studied with crease and folding tests. The Cobb₆₀ test revealed that the coated films were resistant to liquid water, at least for a short exposure time, if the coating thickness was at least 10–17 μm. Water‐vapor transmission rates comparable to those of polyethylene‐laminated films were obtained for coated chitosan at a coating thickness of 5–7 μm. The coated films possessed low oxygen permeability despite the high humidity. Coated films dried for 3 weeks showed oxygen permeabilities at 90% relative humidity that were similar to values for dry ethylene‐co‐vinyl alcohol at 0% relative humidity. The lacquer partly penetrated the whey films, and this led to excellent adhesion but poor lacquer toughness. The lacquer coating on chitosan was tougher, and it was possible to fold these films 90° without the coating fracturing if the coating thickness was small. The coated whey films were readily creasable. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 985–992, 2001