Does the nanometre scale topography of titanium influence protein adsorption and cell proliferation?

To investigate the influence of titanium films with nanometre scale topography on protein adsorption and cell growth, three different model titanium films were utilized in the present study. The chemical compositions, surface topographies and wettability were investigated by using X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and water contact angle measurement, respectively. The films share the same surface chemistry but exhibit different topographies on a nanometre scale. Thus, they act as model systems for biological studies regarding surface topography effects. The films were obtained by varying the deposition rate and the film thickness, respectively. These films displayed nanometre scale surface roughness (root mean square roughness, R_rms) from 2 to 21 nm over areas of 50 μm × 50 μm, with different grain sizes at their surfaces. Albumin and fibrinogen adsorption on these model titanium films were performed in this study. Bicinchoninic acid assay was employed to determine the amount of adsorbed protein on titanium film surfaces. No statistically significant differences, however, were observed for either albumin or fibrinogen adsorption between the different groups of titanium films. No statistically significant influence of surface roughness on osteoblast proliferation and cell viability was detected in the present study.     

发光多孔硅表面的STM研究

自从Canham首次报道了室温下多孔硅的光致发光现象以来^[1],多孔硅已成为半导体光电化学及材料领域内最为热门的研究课题^[2].     

Effects of laser scanning speed on surface roughness and mechanical properties of aluminum/Polylactic Acid (Al/PLA) composites parts fabricated by fused deposition modeling

Although fused deposition modeling (FDM) has gradually become one of the popular additive manufacturing technologies in different industries, high surface roughness has always been an inevitable disadvantage of FDM parts. Laser polishing represents a recent and novel application of laser surface irradiation that can be used for precise, post-process smoothing of the rough surfaces commonly encountered on FDM parts. The influence of laser polishing on surface modification and mechanical properties of aluminum/Polylactic Acid (Al/PLA) composites has been investigated. Laser scanning speed was varied to evaluate its effect on the surface quality and mechanical properties of the experimental samples. The results indicated that laser polishing could enable reductions in surface roughness of over 86.6% (from 23.27 μm to 3.11 μm Sa). The tensile strength of specimen also increased from 41.01 MPa to 51.31 MPa with increasement of 25.1%. The dynamic mechanical analysis (DMA) results showed that there was a remarkable improvement in the storage modulus and glass transition temperature of Al/PLA composite specimens after laser polishing, which suggested that the laser polishing treatment could play a role in decreasing the porosity inside the FDM parts and improve interfacial adhesion between the PLA matrix and Al fibers. Moreover, the fracture morphologies were observed to investigate the possible strengthening mechanism. These results demonstrate how laser polishing can simultaneously smooth and modify the surface characteristics of a FDM part surface.     

Effect of surface morphology on measurement and interpretation of boundary slip on superhydrophobic surfaces

Highly liquid repellent surfaces have been obtained by the combination of roughness and hydrophobicity. Studies have reported that the flow over such surfaces exhibits larger boundary slip as compared to the smooth hydrophobic surfaces. However, the surface roughness can also lead to apparent slip. Thus, the effect of the two factors, that is, wettability and roughness, needs to be segregated. In this study, we have measured the slippage of water on rough hydrophilic and hydrophobic surfaces using colloidal probe atomic force microscopy technique (CP‐AFM). Results showed that the effect of surface roughness on the measured slip is dominant over that of wettability. It was also found that slip on surfaces with sparsely distributed asperities is highly local and measurements on various locations give dissimilar results. The results suggested that the main reason of the larger slip, on rough hydrophobic surfaces, is likely to be the roughness and not the hydrophobicity. Moreover, it was also found that the slip does not vary considerably with the increase or decrease in the shear rate. Most likely, this kind of slip phenomena is caused by the apparent decrease of the drag force, because the nanoasperities on the surface restrict the probe from reaching the surface properly. Copyright © 2016 John Wiley & Sons, Ltd.     

New approach to the immobilization of glucose oxidase on non-porous silica microspheres functionalized by (3-aminopropyl)trimethoxysilane (APTMS)

The immobilization and encapsulation of glucose oxidase (GOD) onto the mesoporous and the non-porous silica spheres prepared by co-condensation of tetraethylorthosilicate (TEOS) and (3-aminopropyl)trimethoxysilane (APTMS) in the water-in-oil (W/O) emulsion system were studied. The terminal amine group was used as the important functionality for GOD immobilization on the silica substrate. When only TEOS is used as a silica source, the disordered mesoporous silica microspheres are obtained. As the molar ratio of APTMS to TEOS (R_AT) increases, the surface area and pore volume of the silica particles measured by nitrogen adsorption and desorption method and SEM decrease rapidly. Particularly, the largest change of the surface morphology is observed between R_AT = 0.20 and R_AT = 0.25. The amount and the adsorption time of immobilized enzyme were measured by UV spectroscopy. About 20 wt% of GOD was immobilized into the silica substrates above R_AT = 0.60 and was completely adsorbed into the substrate of R_AT = 0.80 with lapse of 4 h after addition. In the measurement of the thermal stability, GOD dissolved in buffer solution loses nearly all of its activity after 30 min at 65 °C. In contrast, GOD immobilized on the surface-modified silica particles still retains about 90% of its activity after the same treatment. At this temperature, the immobilized glucose oxidase retained half of its initial activity after 4 h. It is shown that the suitable usage of functionalizing agent like APTMS as well as the control of surface morphology is very important on the immobilization of enzyme.     

Characterization and modification of polymer blend films

Films of immiscible blends of (PS) and poly(methyl methacrylate) (PMMA) were characterized by contact-angle measurements with sessile drop and atomic force microscopy (AFM). These blends showed a linear dependence of the contact angles on the composition, as predicted by Cassie's equation for ideal surfaces. The surface structure investigated by AFM showed low roughness and phase-separation features. The ratio between the drop radius and the roughness amounted to the order of 10⁴–10⁵. This magnitude seemed to be sufficient to put the PS/PMMA films close to ideality. Upon sulfonation, the wettability and the microscopic surface roughness of the PS/PMMA blends increased. The treatment with sulfuric acid yielded sulfonated PS domains on the surface, causing an increase in the surface wettability. The SO₃ ⁻ groups were evidenced by X-ray photoelectron spectroscopy. The sulfonation of the PS/PMMA blends enables the formation of multiphase surfaces with hydrophobic, charged and polar domains. Received: 11 December 2000 Accepted: 6 April 2001     

Laser induced breakdown spectroscopy of soils, rocks and ice at subzero temperatures in simulated martian conditions

We applied Laser Induced Breakdown Spectroscopy (LIBS) on moist soil/rock samples in simulated Martian conditions. The signal behavior as a function of the surface temperature in the range from + 25 °C to − 60 °C was studied at pressure of 7 mbar. We observed the strong signal oscillations below 0 °C with different negative peaks, whose position, width and magnitude depend on the surface roughness. In some cases, the signal was reduced for one order of magnitude with consequences for the LIBS analytical capability. We attribute such a signal behavior to the presence of supercooled water inside the surface pores, which freezing point depends on the pore size. On a same rock samples with different grades of the surface polishing, the signal has different temperature dependence. Its decrease was always registered close to 0 °C, corresponding to the freezing/melting of normal disordered ice, which can be present inside larger pores and scratching. An amount of the signal reduction at the phase transition temperatures does not seem to change with the laser energy density in the examined range. Comparative measurements were performed on a frozen water solution. A large depression, for two orders of magnitude, of the LIBS intensity was observed close to − 50 °C. The same negative peak, but with a smaller magnitude, was also registered on some rock/soil samples. Ablation rates and plasma parameters as a function of the sample temperature are also discussed, and their consequences for in-situ analyses.     

A simultaneous TG–DTA study of the thermal decomposition of 2-hydroxybenzoic acid, 2-carboxyphenyl ester (salsalate)

Simultaneous thermogravimetry–differential thermal analysis (TG–DTA) and gas and liquid chromatography with mass spectrometry detection have been used to study the kinetics and decomposition of 2-hydroxybenzoic acid, 2-carboxyphenyl ester, commercially known as salsalate. Samples of salsalate were heated in the TG–DTA apparatus in an inert atmosphere (100 ml min⁻¹ nitrogen) in the temperature range 30–500 °C. The data indicated that the decomposition of salsalate is a two-stage process. The first decomposition stage (150–250 °C) had a best fit with second-order kinetics with E_a=191–198 kJ/mol. The second decomposition stage (300–400 °C) is described as a zero-order process with E_a=72–80 kJ/mol. The products of the decomposition were investigated in two ways:

(a)Salsalate was heated in a gas chromatograph at various isothermal temperatures in the range 150–280 °C, and the exit gas stream analyzed by mass spectrometry (GC–MS). This approach suggested that salsalate decomposes with the formation of salicylic acid, phenol, phenyl salicylate, and cyclic oligomers of salicylic acid di- and tri-salicylides.

(b)One gram samples of salsalate were heated in a vessel under nitrogen to 150 °C, and the residues were analyzed by liquid chromatography–mass spectrometry (LC–MS). The major compound detected was a linear tetrameric salicylate ester.

     

Preparation and crystal structure of a 1:1 inclusion compound of 1,4,11,14-tetramethoxy-dibenzo[b,n]tetraphenylene with pyridine

The new host 1,4,11,14-tetramethoxy-dibenzo[b,n]tetraphenylene forms a 1:1 inclusion compound with pyridine, in which a pair of centrosymmetrically-related guest species are enclosed in the cage surrounded by six host molecules. C₃₆H₂₈O₄·C₅H₅N, F_W=603.68, triclinic, space group P-1, a=11.796(2), b=16.075(3), c=9.004(2) Å; =98.39(3)°, β=90.01(3)°, γ=108.19(3)°, V=1602.8(5) Å³, Z=2, F(000)=636, D_c=1.251 g/cm³, μ=0.080 mm⁻¹. The final R indices [I>2σ(I)] R₁=0.0759, wR₂=0.1970 for 5623 MoK observed data.     

Influence of the wettability on the boiling onset

Experimental investigation of pool boiling is conducted in stationary conditions over very smooth bronze surfaces covered by a very thin layer of gold presenting various surface treatments to isolate the role of wettability. We show that even with surfaces presenting mean roughness amplitudes below 10 nm the role of surface topography is of importance. The study shows also that wettability alone can trigger the boiling and that the boiling position on the surface can be controlled by chemical grafting using for instance alkanethiol. Moreover, boiling curves, that is, heat flux versus the surface superheat (which is the difference between the solid surface temperature and the liquid saturation temperature), are recorded and enabled to quantify, for this case, the significant reduction of the superheat at the onset of incipient boiling due to wettability.     

Thermal decomposition of zinc carbonate hydroxide

This study is devoted to the thermal decomposition of two zinc carbonate hydroxide samples up to 400 °C. Thermogravimetric analysis (TGA), boat experiments and differential scanning calorimetry (DSC) measurements were used to follow the decomposition reactions. The initial samples and the solid decomposition products were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) and laser particle size analyzer. Results showed that zinc carbonate hydroxide decomposition started at about 150 °C and the rate of decomposition became significant at temperatures higher than 200 °C. The apparent activation energies (E_a) in the temperature range 150–240 °C for these two samples were 132 and 153 kJ/mol. The XRD analyses of the intermediately decomposed samples and the DSC results up to 400 °C suggested a single-step decomposition of zinc carbonate hydroxide to zinc oxide with not much change in their overall morphologies.     

Atomic Force Microscopy Analysis of Statistical Roughness of GaAs Surfaces Originated by Thermal Oxidation

We have determined the important statistical quantities of the rough boundary between a GaAs single crystal and its oxide film formed by thermal oxidation. Thermal oxidation of the GaAs surfaces was performed at the temperature of 500°C. Using mathematical procedures developed for treating AFM data consisting of a family of the values of the heights of the irregularities of this roughness the values of the important statistical quantities of roughness were determined for 11 samples of the GaAs surfaces created by dissolution of the thermal oxide films originated during thermal oxidation of the smooth GaAs samples (the times of oxidation of these 11 samples were within interval of 20min–8 hours). From the AFM analysis of the roughness of GaAs surfaces it was found that the roughnening of these surfaces was the most pronounced for shorter oxidation times, i.e. for times smaller than about 2 hours.     

Polycrystalline Gold Electrodes: A Comparative Study of Pretreatment Procedures Used for Cleaning and Thiol Self‐Assembly Monolayer Formation

The influence of different surface pretreatment procedures on the electrochemical response of a polycrystalline gold electrode was evaluated. Mechanical polishing with slurry alumina (M), chemical oxidation with H₂SO₄/H₂O₂ (C), electrochemical polishing (potential cycling between ?0.1 V and 1.2 V vs. SCE) (E), chemical reduction with ethanol, and combinations among these treatments were employed to change the surface electrode characteristics. The efficiency of the proposed pretreatments was evaluated by electrochemical responses towards the redox couple ferri(II/III)‐ammonium sulfate and by the formation of a self‐assembly monolayer of 3‐mercaptopropionic acid (3 MPA SAM) on gold electrodes. The procedure (C) allowed important gold surfaces activation. Using procedures (C) and (E) the roughness of polycrystalline gold surfaces was significantly minimized and more reproducible surfaces could be obtained. From the profile of reductive desorption of 3 MPA SAM it was possible to verify that reduced gold surfaces generated better packed monolayers than oxidized ones and a comparative study using CV and DPV techniques showed that between the two desorption peaks, the one localized at more negative potential values corresponds to the cleavage of Au‐S bond from the chemisorbed thiol. In general, the improvement in the studied electrochemical responses could not only be attributed to an increase in the real surface area of the electrode, but to the chemical surface states set off by the pretreatment procedure.     

Wettability of Microstructured Hydrophobic Sol-Gel Coatings

The formation of appropriate surface patterns on hydrophobic surfaces leads to a general change in their wettability and the contact angle increases substantially. Such coatings are of great technical interest, especially if aqueous media are concerned as in the prevention of ice-adhesion. For this reason various fluorine containing nanocomposite coatings have been developed by sol-gel processing.The morphology of these hydrophobic surfaces has been controlled by varying the content of silica particles regarding size, degree of aggregation, and concentration. The wettability is characterized by the measurement of dynamic contact angles against water. The complete range of different wettability regimes is accessible, i.e. smooth surfaces (both low advancing contact angle and hysteresis between advancing and receding contact angle), surfaces within the Wenzel regime (high advancing contact angle and hysteresis), and superhydrophobic surfaces (high advancing contact angle and low hysteresis). The wettability is correlated with the surface roughness as determined using a profilometer or AFM.The wettability of superhydrophobic surfaces is greatly dependent on the surface tension of the liquid. By comparison of the tiltangle _t of a smooth and a superhydrophobic surface, a critical surface tension _c is identified, where _t (smooth surface) = _t (microstructured surface). The microstructured surface provides a better run-off of liquids _lg > _c 55 mN·m^–1.     

Enhancement of surface wettability via the modification of microtextured titanium implant surfaces with polyelectrolytes

Micrometer- and submicrometer-scale surface roughness enhances osteoblast differentiation on titanium (Ti) substrates and increases bone-to-implant contact in vivo. However, the low surface wettability induced by surface roughness can retard initial interactions with the physiological environment. We examined chemical modifications of Ti surfaces [pretreated (PT), R(a) ≤ 0.3 μm; sand blasted/acid etched (SLA), R(a) ≥ 3.0 μm] in order to modify surface hydrophilicity. We designed coating layers of polyelectrolytes that did not alter the surface microstructure but increased surface ionic character, including chitosan (CHI), poly(L-glutamic acid) (PGA), and poly(L-lysine) (PLL). Ti disks were cleaned and sterilized. Surface chemical composition, roughness, wettability, and morphology of surfaces before and after polyelectrolyte coating were examined by X-ray photoelectron spectroscopy (XPS), contact mode profilometry, contact angle measurement, and scanning electron microscopy (SEM). High-resolution XPS spectra data validated the formation of polyelectrolyte layers on top of the Ti surface. The surface coverage of the polyelectrolyte adsorbed on Ti surfaces was evaluated with the pertinent SEM images and XPS peak intensity as a function of polyelectrolyte adsorption time on the Ti surface. PLL was coated in a uniform thin layer on the PT surface. CHI and PGA were coated evenly on PT, albeit in an incomplete monolayer. CHI, PGA, and PLL were coated on the SLA surface with complete coverage. The selected polyelectrolytes enhanced surface wettability without modifying surface roughness. These chemically modified surfaces on implant devices can contribute to the enhancement of osteoblast differentiation.     

Influence of sample deposition and coating with Zr and Pd on the atomization kinetics of germanium in graphite furnace atomic absorption spectrometry

Atomization of germanium from zirconium-coated (ZrGT), palladium-coated (PdGT) and palladium-zirconium-coated graphite tubes (PZGT) by aqueous deposition of the analyte solution and/or the trapping of the gaseous hydride has been investigated. From the activation energies calculated based on Smets' method, it was found that both the mode of sample introduction and the nature of the atomizer surface have an effect on the atom formation of germanium. Activation energies E_a of 383.9 ± 17.1, 445.8 ± 19.8 and 557.9 ± 12.4 kJ mol⁻¹ were observed for germanium atomization from ZrGT, PZGT and PdGT, respectively. A much larger E_a value of 950.2 ± 13.1 kJ mol⁻¹ was obtained for Ge from PdGT by the trapping of GeH₄. XPS results do not give sufficient evidence for Pd-Ge compound formation.     

Comparison of Electropolishing of Aluminum in a Deep Eutectic Medium and Acidic Electrolyte

Research advances in electropolishing, with respect to the field of metalworking, have afforded significant improvements in the surface roughness and conductivity properties of aluminum polished surfaces in ways that machine polishing and simple chemical polishing cannot. The effects of a deep eutectic medium as an acid-free electrolyte were tested to determine the potential energy thresholds during electropolishing treatments based upon temperature, experiment duration, current, and voltage. Using voltammetry and chronoamperometry tests during electropolishing to supplement representative recordings via atomic force microscopy (AFM), surface morphology comparisons were performed regarding the electropolishing efficiency of phosphoric acid and acid-free ionic liquid treatments for aluminum. This eco-friendly solution produced polished surfaces superior to those surfaces treated with industry standard acid electrochemistry treatments of 1 M phosphoric acid. The roughness average of the as-received sample became 6.11 times smoother, improving from 159 nm to 26 nm when electropolished with the deep eutectic solvent. This result was accompanied by a mass loss of 0.039 g and a 7.2 µm change in step height along the edge of the electropolishing interface, whereas the acid treatment resulted in a slight improvement in surface roughness, becoming 1.63 times smoother with an average post-electropolishing roughness of 97.7 nm, yielding a mass loss of 0.0458 g and a step height of 8.1 µm.     

仿生智能浸润性表面研究的新进展

简要介绍了固体表面浸润性的概念及近年来的相关理论研究成果, 并概述了自然界中具有特殊浸润性表面的生物体典型实例以及仿生制备的特殊浸润性表面和智能响应表面, 展望了具有特殊浸润性表面的研究方向.     

Preparation of ultrafiltration membranes of HCEC and CTA blend, and studies of resistance to microbiological degradation and other properties

Blends of high cyanoethylated cellulose (HCEC) (D_s = 2.5) and cellulose triacetate (CTA) (D_s = 2.8) were prepared for evaluation as ultrafiltration membranes. The rejection R_a and water permeability (P_w) of these membranes with respect to bovine serum albumin (BSA), were measured with the variations in composition and conditions of preparation. It was possible to define the reaction conditions and compositions that offered optimum performance with respect to R_a and J_w, and resistance to microbial degradation as well as acid and alkali hydrolysis. The morphology of membrane thereby obtained was characterized by scanning electron microscopy (SEM). The UF membrane cast from a solution of 1,4-dioxane: 12.5 g, acetone: 12.5 g, HCEC: 1.5 g, CTA: 3 g and PEG (MW = 1000): 10.5 g showed the optimum performance of P_w = 10 × 10⁻¹⁰ m³/(m² s Pa), BSA Rejection (R_a) = 99%, (J_w = 17.3 m³/(m² day) at ΔP = 0.2 MPa) and a molecular weight cut off at 4.9 × 10⁴ Da. After immersion in mud for 170 days, reduction of R_a was only 8% for UF membrane containing 10 wt% HCEC blend, and was not observed to be obviously different from the membrane containing more than 30 wt% HCEC blend. The higher permeability and rejection of blend membrane may be attributable to the network structure formed via CTA and HCEC penetration.     

Structural and theoretical studies of Xe(OChF5)2 and [XeOChF5][AsF6] (Ch = Se, Te)

The XeOSeF₅⁺ cation has been synthesized for the first time and characterized in solution by ¹⁹F, ⁷⁷Se and ¹²⁹Xe NMR spectroscopy and in the solid state by X-ray crystallography and Raman spectroscopy with AsF₆⁻ as its counter anion. The X-ray crystal structures of the tellurium analogue and of the Xe(OChF₅)₂ derivatives have also been determined: [XeOChF₅][AsF₆] crystallize in tetragonal systems, P4/n, a=6.1356(1) Å, c=13.8232(2) Å, V=520.383(14) Å³, Z=2 and R₁=0.0453 at −60°C (Te) and a=6.1195(7) Å, c=13.0315(2) Å, V=488.01(8) Å³, Z=2 and R₁=0.0730 at −113°C (Se); Xe(OTeF₅)₂ crystallizes in a monoclinic system, P2₁/c, a=10.289(2) Å, b=9.605(2) Å, c=10.478(2) Å, β=106.599(4)°, V=992.3(3) Å³, Z=4 and R₁=0.0680 at −127°C; Xe(OSeF₅)₂ crystallizes in a triclinic system, , a=8.3859(6) Å, c=12.0355(13) Å, V=732.98(11) Å³, Z=3 and R₁=0.0504 at −45°C. The energy minimized geometries and vibrational frequencies of the XeOChF₅⁺ cations and Xe(OChF₅)₂ were calculated using density functional theory, allowing for definitive assignments of their experimental vibrational spectra.