Determination of Protamine and Insulin Using Short-End Injection Capillary Electrophoresis

A fast and inexpensive method for simultaneous determination of total protamine and insulin has been developed using capillary electrophoresis in the short-end injection setup with a bare-fused silica capillary. Optimized background electrolyte consists of 45 mM aqueous solution of phosphoric acid, pH 1.85. Separation is finished within 1 min; total analysis time including preconditioning is 4 min. The method exhibits excellent linearity within the concentration range 2.5–500 μg mL⁻¹ for both analytes. Limits of detection are 1.0 and 0.7 μg mL⁻¹ for protamine and insulin, respectively. Accuracy of the method has been successfully tested on a real sample of Neutral Protamine Hagedorn Insulin (NPH insulin) injection. The background electrolyte employed is inexpensive and experiments have shown that it does not need to be exchanged for at least 20 subsequent analyses.

     

Simultaneous capillary electrophoresis competitive immunoassay for insulin, glucagon, and islet amyloid polypeptide secretion from mouse islets of Langerhans

A capillary electrophoresis competitive immunoassay was developed for the simultaneous quantitation of insulin, glucagon, and islet amyloid polypeptide (IAPP) secretion from islets of Langerhans. Separation buffers and conditions were optimized for the resolution of fluorescein isothiocyanate (FITC)-labeled glucagon and IAPP immunoassay reagents, which were excited with the 488 nm line of an Ar(+) laser and detected at 520 nm with a photomultiplier tube (PMT). Cy5-labeled insulin immunoassay reagents were excited by a 635 nm laser diode module and detected at 700 nm with a separate PMT. Optimum resolution was achieved with a 20mM carbonate separation buffer at pH 9.0 using a 20 cm effective separation length with an electric field of 500 V/cm. Limits of detection for insulin, glucagon, and IAPP were 2, 3, and 3 nM, respectively. This method was used to monitor the simultaneous secretion of these peptides from as few as 14 islets after incubation in 4, 11, and 20 mM glucose for 6h. For insulin and IAPP, a statistically significant increase in secretion levels was observed, while glucagon levels were significantly reduced in the 4 and 11 mM glucose conditions. To further demonstrate the utility of the assay, the Ca(2+)-dependent secretion of these peptides was demonstrated which agreed with published reports. The ability to examine the secretion of multiple peptides may allow for the determination of regulation of secretory processes within islets of Langerhans.     

Development of a capillary electrophoresis method for the characterization of collagens in cartilage tissue

The use of capillary electrophoresis (CE) for the separation of peptides specific to type I and type II collagen is evaluated. The aim of this work is to develop a method to characterize cartilage, cartilage repair tissue, and tissue engineered cartilage. The analysis is dependent on the cleavage of collagen into constituent peptides by cyanogen bromide. A number of these peptides are specific to the collagen type. CE is evaluated for the separation of these specific peptides using uncoated and coated capillaries over a wide range of pH and buffer concentrations. Separation of peptides specific to type I and type II collagen is achieved using a Supelco CElect N capillary and a 100mM phosphate buffer at pH 6. Meniscal cartilage is characterized using this method. The proportion of type I collagen to type II collagen corresponds well with that reported by others and indicates the potential of this method for the characterization of cartilage.     

Spherical molecularly imprinted polymer particles: a promising tool for molecular recognition in capillary electrokinetic separations

Spherical molecularly imprinted polymer particles obtained via precipitation polymerization, were introduced as a pseudostationary phase in capillary electrophoresis (CE) to study molecular recognition. Analyses were performed via a partial filling technique using (+)-ephedrine-imprinted microspheres (100-200 nm) which were polymerized from methacrylic acid and 1,1,1-Tris(hydroxymethyl)propanetrimethacrylate using acetonitrile as the solvent. The influence of pH and the modifier content on the separation was investigated. A 0.1% w/v suspension in an aqueous 10 mM phosphate buffer (pH 2.5 with 40% acetonitrile) was hydrodynamically injected into the CE system (80% of the effective capillary length) and led to full baseline separation of racemic ephedrine within 10 min.     

Enantiomeric separation of citalopram and its metabolites by capillary electrophoresis

A simple and fast capillary electrophoretic method has been developed for the enantioselective separation of citalopram and its main metabolites, namely N-desmethylcitalopram and N,N-didesmethylcitalopram, using beta-cyclodextrin (beta-CD) sulfate as the chiral selector. For method optimisation several parameters were investigated, such as CD and buffer concentration, buffer pH, and capillary temperature. Baseline enantioseparation of the racemic compounds was achieved in less than 6 min using a fused-silica capillary, filled with a background electrolyte consisting of a 35 mM phosphate buffer at pH 2.5 supplemented with 1% w/v beta-CD sulfate and 0.05% w/v beta-CD at 25 degrees C and applying a voltage of -20 kV. A fast separation method for citalopram was also optimized and applied to the analysis of pharmaceutical formulations. Racemic citalopram was resolved in its enantiomers in less than 1.5 min using short-end injection (8.5 cm, effective length) running the experiments in a background electrolyte composed of a 25 mM citrate buffer at pH 5.5 and 0.04% w/v beta-CD sulfate at a temperature of 10 degrees C.     

Quality control of benserazide-levodopa and carbidopa-levodopa tablets by capillary zone electrophoresis

In modern practice, the treatment of Parkinson's disease and syndrome is carried out using pharmaceutical formulations containing a combination of levodopa and a decarboxylation inhibitor (carbidopa or benserazide). Two pharmaceutical formulations were quantified by capillary zone electrophoresis using two procedures which differed only in the kind of background electrolyte used. One procedure used a 25 mM phosphate buffer, pH 2.5, while the second one used a 25 mM borate buffer, pH 8.5. The electrophoretic analysis was carried out using an uncoated fused- silica capillary, a separation voltage of 20 kV with currents typically less than 60 microA, and spectrophotometric detection at 205 nm. Calibration curves were performed for levodopa (concentration range 1-100 microg/mL), for carbidopa and benserazide (1-50 microg/mL), and the plots of the peak area versus concentration were found to be linear with a correlation coefficient better than 0.9990. Satisfactory results were obtained when commercial tablets were analyzed in terms of accuracy (98-102%), repeatability (0.6-2.0%), and intermediate precision (1.1-2.6%).     

Investigation of folic acid stability in fortified instant noodles by use of capillary electrophoresis and reversed-phase high performance liquid chromatography

A single enzyme treatment with alpha-amylase, prior to the quantification of added folic acid (FA) in fortified instant fried Asian noodles with analysis performed by capillary zone electrophoresis (CZE) and reversed-phase high performance liquid chromatography (RP-HPLC) with UV detection, is described. The method was validated and optimized for capillary electrophoresis (CE) with separation achieved using a 8 mM phosphate-12 mM borate run buffer with 5% MeOH at pH 9.5. FA was well separated from matrix components with nicotinic acid (NA) employed as an internal standard. In a comparative study, separation of FA was performed using HPLC with a mobile phase consisting of 27% MeOH (v/v) in aqueous potassium phosphate buffer (3.5 mM KH(2)PO(4) and 3.2 mM K(2)HPO(4)), pH 8.5, and containing 5 mM tetrabutylammonium dihydrogen phosphate as an ion-pairing agent. For both methods, excellent results were obtained for various analytical parameters including linearity, accuracy and precision. The limit of detection was calculated to be 2.2 mg/L for CE without sample stacking and 0.10 mg/L with high performance liquid chromatography (HPLC). Sample extraction involved homogenization and enzymatic extraction with alpha-amylase. Results indicated that FA was stable during four main stages of instant fried noodle manufacturing (dough crumbs, cut sheets, steaming and frying).     

Efficient and reproducible analysis of peptides by capillary electrophoresis using noncovalently bilayer-coated capillaries

The usefulness of a noncovalent capillary coating consisting of two layers of oppositely charged polymers for the separation of peptides with capillary electrophoresis (CE) was studied. Capillaries were coated simply by subsequently flushing with solutions of 1% m/v Polybrene and 1% v/v poly(vinylsulfonate) (PVS) forming a bilayer, which showed to produce a strong and highly reproducible electroosmotic flow (EOF) at low pH. Using this coating in combination with a background electrolyte (BGE) containing sodium phosphate (pH 2.5) and 0.01% v/v PVS, initially broadened and overlapping peaks were obtained for some test peptides. By omitting the PVS from the BGE, the peak width and shape of the peptides improved resulting in baseline separation. A systematic study of the influence of the BGE composition showed that considerable further enhancement of the separation efficiency was achieved by increasing the ionic strength of the BGE. Using a BGE of 200 mM tris(hydroxymethyl)aminomethane (Tris)-phosphate (pH 2.5) plate numbers for the peptides were in the 300 000-600 000 range and the relative standard deviation of the peptide migration times was less then 0.3% (n = 5). The use of Tris-phosphate instead of sodium phosphate allowed the current to stay within acceptable limits when 30 kV was used as separation voltage. Overall, the bilayer coating showed a remarkable EOF repeatability, as well as long-term stability. Compared to bare fused-silica capillaries the intraday and interday repeatability of migration times was very favorable and coated capillaries could be used for over a month performing analyses with low and high ionic strength BGEs without any performance deterioration. The usefulness of the bilayer-coated capillaries for the analysis of positively charged peptides was demonstrated by the fast and efficient separation of various closely related enkephalins and the baseline separation of an isomeric peptide/peptoid couple exhibiting efficiencies of over 550 000 plates.     

Simultaneous determination of cloramphenicol, salicylic acid and resorcinol by capillary zone electrophoresis and its application to pharmaceutical dosage forms

This study demonstrates the separation of active ingredients in acne formulations (salicylic acid, cloramphenicol and resorcinol in presence of azulene) by capillary zone electrophoresis. Factors affecting their separations were the buffer pH and concentration, applied voltage, sample preparation, and presence of additives. Optimun results were obtained with a 50 mM sodium tetraborate-50 mM sodium phosphate, pH 9.0. The carrier electrolyte gave baseline separation with good resolution, short migration times (<6 min), great reproducibility and accuracy. Calibration plots were linear over at least three orders of magnitude of analyte concentrations, the lower limits of detection being within the range 0.39-1.25 μg ml⁻¹. The procedure was fast and reliable and commercial pharmaceuticals could be analysed without prior sample clean-up procedure.     

Study of peptide-ligand interactions in open-tubular capillary columns covalently modified with porphyrins

The inner surface of fused silica capillaries has been covalently modified with different porphyrins (deuteroporphyrin, complexes of deuteroporphyrin with metal ions Fe(III), Cu(II), Zn(II), Ni(II), and Cu(II)-meso-tetra (carboxyphenyl) porphyrin) and it was applied for the separation of biologically active peptides by open-tubular capillary electrochromatography. Separations were performed in a mobile phase composed of 25?mM potassium phosphate, pH 4.0, 5%?v/v ACN and 10?mM hydroquinone. Changes in the effective electrophoretic mobility of peptides were studied concerning porphyrin central metal atom, attachment geometry, and the presence of coordinating or aromatic amino acid residues in the peptide sequence. The results showed that differences in metal core on the porphyrin and the spatial conformation of attached porphyrin result in changes in the analyte interaction with the stationary phase.     

Gold nanomaterials based pseudostationary phases in capillary electrophoresis: A brand‐new attempt at chondroitin sulfate isomers separation

In this work, a CE method with bare gold nanorods (GNRs) based pseudostationary phase was developed and applied for the separation of chondroitin sulfate (CS) isomers, CS, and dermatan sulfate (DS). The separation efficiency was investigated by varying the experimental parameters such as concentration and pH of the BGE, separation voltage, internal diameter of capillary, different size, and morphology of gold nanomaterials. Results showed that different size and morphology of gold nanomaterials had different effects on the separation of CS and DS. The best separation of CS and DS was achieved in the BGE composed of aqueous 150 mmol/L (mM) ethylenediamine + 20 mM sodium dihydrogen phosphate + 30% v/v GNRs, pH 4.5, at the separation voltage of ?10 kV. Capillary was 59.2 cm in length (effective length 49 cm), 50 μm id capillary thermostated at 25°C. CE with bare GNRs used as pseudostationary phase was shown to be a suitable technique for the separation of CS and DS mixtures with wider peaks. RSD of migration time and peak area of CS and DS were 0.13, 0.14 and 0.86, 1.07%, respectively.     

Separation of antidepressants by capillary electrophoresis with in-line solid-phase extraction using a novel monolithic adsorbent

The separation of three selective serotonin reuptake inhibitors (SSRIs) by capillary electrophoresis (CE) with fully integrated solid-phase extraction (SPE) is described. Polymeric monolithic SPE modules were prepared in situ within a fused silica capillary from either butyl methacrylate-co-ethylene dimethacrylate or 3-sulfopropyl methacrylate-co-butyl methacrylate-co-ethylene dimethacrylate. Using a 1 cm SPE module placed at the inlet of the capillary, a mixture of sertraline, fluoxetine and fluvoxamine was extracted from aqueous solution by applying a simple pressure rinse. Under pressure-driven conditions, efficient elution was possible from both SPE materials investigated using 50 mM phosphate buffer, pH 3.5 in acetonitrile (20/80, v/v). Two different strategies were investigated for the efficient elution and subsequent CE separation. Injection of an aqueous sample plug directly into the non-aqueous elution/separation buffer was found to be unsuitable with poor elution profiles observed in the electrodriven mode. Alternatively, a sample plug equivalent to several capillary volumes could be injected by pressure followed by filling the capillary with the non-aqueous elution/separation buffer from the outlet end using a combination of pressure and electrodriven flow. Using a neutral monolith, efficient elution/separation was not possible due to an unstable electroosmotic flow (EOF), however, by adding the ionisable monomer, 3-sulfopropyl methacrylate to the SPE module to increase and stabilise the EOF, it was possible to achieve efficient elution from the SPE module, followed by baseline separation by CE using a 200 mM acetate buffer, pH 3.5 in acetonitrile (10/90, v/v). With enrichment factors of over 500 achieved for each of the analytes this demonstrates the potential of in-line SPE-CE for the sensitive analysis of these drugs.     

Capillary electrophoresis determination of six bioactive constituents in San-huang-hsieh-hsin-tang

A capillary electrophoretic method for simultaneous determination of six bioactive ingredients (berberine, palmatine, baicalin, sennoside B, emodin, and sennoside A) in the Chinse herbal formula San-huang-hsieh-hsin-tang was established. A carrier composed of aqueous buffer solution (50 mM sodium cholate, 15 mM sodium dihydrogen phosphate, and 4.25 mM sodium borate)-acetonitrile (3:2) was found to be the most suitable electrolyte for this separation. Contents of these constituents in a non-pretreated methanol-water extract of San-huang-hsieh-hsin-tang sample could be easily determined within 20 min. The effects of borate, cholate, and organic modifier (acetonitrile) concentration of the carrier on the migration behavior of the solutes were also studied.     

Peptide mapping with mobile phases of intermediate pH value using capillary reversed-phase high-performance liquid chromatography/electrospray ionisation tandem mass spectrometry

This investigation describes the separation of tryptic peptides by capillary reversed-phase high-performance liquid chromatography (RP-HPLC) with eluents in the intermediate pH range, followed by in-line electrospray ionisation tandem mass spectrometry (ESI-MS/MS) analysis. For these purposes, gradient elution procedures with an aqueous eluent containing 20 mM ammonium formate, and an increasing content of acetonitrile or methanol, were employed. Compared to the analysis of the same tryptic peptides under low-pH conditions with an ion-pairing reagent, the increase in the pH with the 20 mM ammonium formate mobile phase led to significant changes in both peptide retention to the reversed-phase column and the collision-induced dissociation at the MS/MS stage as a consequence of the changes in the physico-chemical properties of these peptides, such as their overall charge, polarity and relative hydrophobicity. Thus, improved selectivity for the peptide separation and favourable tandem mass spectrometry analysis could be obtained with eluents in this intermediate pH range. The number of tryptic peptides identified by the new approach for the proteins investigated were significantly higher than that obtained by the conventional low-pH methods. Moreover, analysis of protein digests at very low concentrations was also performed under both acidic and intermediate pH conditions and similar improvements in selectivity and MS/MS detection limits were observed, i.e. identification of more distinct peptides and higher sequence coverage of the protein was obtained when eluents of intermediate pH were employed. This study therefore highlights the potential of conducting peptide mapping in the intermediate pH range to achieve more reliable and sensitive protein identifications with capillary RP-HPLC–ESI-MS/MS.     

Evaluation of the interaction between sitagliptin and cyclodextrin derivatives by capillary electrophoresis and nuclear magnetic resonance spectroscopy

An aqueous capillary electrophoretic method was developed for chiral analysis of the novel anti-diabetic drug, sitagliptin. The acid-base profiling of the analyte was carried out using both capillary electrophoresis and nuclear magnetic resonance pH titrations. The apparent complex stability and chiral separation properties were investigated with 30 different cyclodextrins under acidic conditions. The effect of concentration and pH of the BGE, temperature of the capillary, and the type and concentration of the chiral selector on the enantiomer resolution were thoroughly investigated. The effects of dual cyclodextrin systems on separation were also extensively studied. Complete separation of racemic sitagliptin with good resolution (R(S)=2.24) was achieved within a short time (15 min) with optimized parameters (10°C, pH=4.4, 40 mM phosphate buffer) of a sulfobutylether-β-cyclodextrin (averaged degree of substitution ~4) and native β-cyclodextrin dual system. The averaged stoichiometry of the inclusion complex was determined using the Job plot method with both (1)H and (19)F NMR experiments and resulted in a 1:1 complex. The structure of the inclusion complex was elucidated using 2-D ROESY NMR experiments.     

Rapid separation of peptides and proteins by isocratic capillary electrochromatography at elevated temperature

The use of capillary electrochromatography (CEC) for the separation by isocratic elution of synthetic peptides, proteins as well as the tryptic digest of cytochrome c has been demonstrated. The monolithic porous stationary phase was prepared from silanized fused-silica capillaries of 75 microm I.D. by in situ copolymerization of vinylbenzyl chloride and ethylene glycol dimethacrylate in the presence of propanol and formamide as the porogens. The chloromethyl groups at the surface of the porous monolith were reacted with N,N-dimethylbutylamine to form a positively charged chromatographic surface with fixed n-butyl chains. Results of studies on the influence of temperature and mobile phase composition on the retention and selectivity of separation by CEC demonstrated the feasibility of rapid polypeptide analysis and tryptic mapping at elevated temperature with high resolution and efficiency. Typically the chromatography of a tryptic digest of cytochrome c took about 5 min at 55 degrees C and 75 kV/m with hydro-organic mobile phases containing acetonitrile in 50 mM phosphate buffer, pH 2.5. For peptides and proteins plots of logarithmic k'cec against acetonitrile concentration were nonlinear, whereas Arrhenius plots for the mobilities were nearly linear. Comparison of the separation of such samples under conditions of CEC and capillary zone electrophoresis (CZE) indicates that the mechanism of separation in CEC is unique and leads to a chromatographic profile different from that obtained by CZE.     

Capillary electrophoresis behavior of water-soluble anionic porphyrins in the presence of beta-cyclodextrin and its O-methylated derivatives

The electrophoretic behavior of water-soluble anionic porphyrins, such as meso-tetrakis(4-carboxyphenyl) porphyrin (TCPP), meso-tetrakis(4-sulfonatophenyl) porphyrin (TSPP) and its zinc(II) and copper(II) complexes (ZnTSPP and CuTSPP, respectively) has been studied by capillary zone electrophoresis using fused-silica capillaries. The selectivity of the separation is strongly dependent on the type and concentration of betacyclodextrin (betaCD) or the O-methylated derivatives added to the background electrolyte. CuTSPP and TSPP can be separated using a pH 2.5 aqueous sodium phosphate buffer in the presence of 1 mM betaCD. Resolution is poorer or absent employing alkylated betaCDs, such as the heptakis (2,6-di-O-methyl)-beta-cyclodextrin or the heptakis(2,3,6-triO-methyl)-beta-cyclodextrin, as additives. On the other hand, separation of TSPP from its copper and zinc complexes has been achieved using a pH 7.0 aqueous sodium phosphate buffer, in the presence of 0.75 mM betaCD and 20% dimethyl sulfoxide (DMSO) as organic modifier. Under such conditions, the calibration curve for quantitative analysis of copper(II) was obtained. A rationale for the observed behavior will be presented and discussed on the basis of binding and protonation equilibria and a simple mathematical model.     

Micellar electrokinetic capillary chromatography of macrolide antibiotics. Separation of tylosin, erythromycin and their related substances.

The separation of tylosin by micellar electrokinetic capillary chromatography with a mixed micelle system is described. Good selectivity was obtained with sodium phosphate buffer (80 mM, pH 7.5) containing 20 mM sodium cholate and 7 mM cetyltrimethylammonium bromide (CTAB). This method permits tylosin to be separated from its closely related substances within 15 min. The influences of type of buffer, buffer pH, the concentrations of sodium cholate and CTAB were investigated. The robustness of the method was examined for tylosin by means of a full-fraction factorial design. Quantitative results are presented. Using a similar buffer system (80 mM sodium phosphate, pH 6.0, 20 mM sodium cholate and 5 mM CTAB), separation of erythromycin and its main related substances was also obtained. However, detection sensitivity and resolution are not sufficient for analysis of related substances in erythromycin commercial samples.     

Evaluation of capillary liquid chromatography-electrospray ionization ion mobility spectrometry with mass spectrometry detection

Due to the proteomics revolution, multi-dimensional separation and detection instruments are required to evaluate many peptides and proteins in single samples. In this study, electrospray ionization (ESI) ion mobility spectrometry (IMS) was evaluated as an additional separation after HPLC separations. Common HPLC mobile phase compositions (solvents, acid modifiers, and buffers) were assessed for the effect on ESI-IMS response. Up to 5 mM sodium phosphate, a non-volatile buffer, was able to be electrosprayed into the IMS without degradation of the instrumental performance. Due to the rapid separation times of IMS, multiple IMS spectra were obtained within a single HPLC peak. A five-peptide mixture was separated in a capillary HPLC column under isocratic conditions within 3 min. Coelution of two peaks due to non-optimal HPLC conditions occurred and these two peaks could not be distinguished by HPLC with UV detection. In contrast, the single ion mobility chromatograms provided separation of each peptide as well as providing a second degree of analyte identification (HPLC retention time and IMS mobility). Furthermore, IMS-MS analysis of the five peptides and comparison with HPLC retention times showed that each peptide had a unique retention time-ion mobility-mass to charge value. This work showed that IMS could be employed for direct separation and detection of HPLC eluents and also could be combined with HPLC-MS for three unique dimensions of separation.     

Capillary zone electrophoresis for analysis of phytochelatins and other thiol peptides in complex biological samples derivatized with monobromobimane

A new method to improve the analysis of phytochelatins and their precursors (cysteine, gamma-Glu-Cys, and glutathione) derivatized with monobromobimane (mBrB) in complex biological samples by capillary zone electrophoresis is described. The effects of the background electrolyte pH, concentration, and different organic additives (acetonitrile, methanol, and trifluoroethanol) on the separation were studied to achieve optimum resolution and number of theoretical plates of the analyzed compounds in the electropherograms. Optimum separation of the thiol peptides was obtained with 150 mM phosphate buffer at pH 1.60. Separation efficiency was improved when 2.5% v/v methanol was added to the background electrolyte. The electrophoretic conditions were 13 kV and capillary dimensions with 30 cm length from the inlet to the detector (38 cm total length) and 50 microm inner diameter. The injection was by pressure at 50 mbar for 17 s. Under these conditions, the separation between desglycyl-peptides and phytochelatins was also achieved. We also describe the optimum conditions for the derivatization of biological samples with mBrB to increase electrophoretic sensitivity and number of theoretical plates. The improved method was shown to be simple, reproducible, selective, and accurate in measuring thiol peptides in complex biological samples, the detection limit being 2.5 microM glutathione at a wavelength of 390 nm.