Using comprehensive two-dimensional gas chromatography for the analysis of oxygenates in middle distillates I. Determination of the nature of biodiesels blend in diesel fuel

In the current energetic context (increasing consumption of vehicle fuels, greenhouse gas emission etc.) government policies lead to mandatory introduction in fossil fuels of fuels resulting from renewable sources of energy such as biomass. Blending of fatty acid alkyl esters from vegetable oils (also known as biodiesel) with conventional diesel fuel is one of the solutions technologically available; B5 blends (up to 5%w/w esters in fossil fuel) are marketed over Europe. Therefore, for quality control as well as for forensic reasons, it is of major importance to monitor the biodiesel origin (i.e. the fatty acid ester distribution) and its content when it is blend with petroleum diesel. This paper reports a comprehensive two-dimensional gas chromatography (GC x GC) method that was developed for the individual quantitation of fatty acid esters in middle distillates matrices. Several first and the second dimension columns have been investigated and their performances to achieve (i) a group type separation of hydrocarbons and (ii) individual identification and quantitation of fatty acid ester blend with diesel are reported and discussed. Finally, comparison of quantitative GC x GC results with reference methods demonstrates the benefits of GC x GC approach which enables fast and reliable individual quantitation of fatty acid esters in one single run. Results show that under developed chromatographic conditions, quantitative group type analysis of hydrocarbons is also possible, meaning that simultaneous quantification of hydrocarbons and fatty acid esters can be achieved in one single run.     

Analysis of biodiesel/petroleum diesel blends with comprehensive two-dimensional gas chromatography

Comprehensive two-dimensional gas chromatography (GCxGC) is used to analyze petroleum diesel, biodiesel, and biodiesel/petroleum diesel blends. The GCxGC instrument is assembled from a conventional gas chromatograph fitted with a simple, in-line fluidic modulator. A 5% phenyl polydimethylsiloxane primary column is coupled to a polyethylene glycol secondary column. This column combination generates chromatograms where the fatty acid methyl esters (FAMEs) found in biodiesel occupy a region that is also populated by numerous cyclic alkanes and monoaromatics found in petroleum. Fortunately, the intensities of the petroleum hydrocarbon peaks are far lower than the intensities of the FAME peaks, even for blends with low biodiesel content. This allows the FAMEs to be accurately quantitated by direct integration. The method is calibrated by analyzing standard mixtures of soybean biodiesel in petroleum diesel with concentrations ranging from 1 to 20% v/v. The resulting calibration curve displays excellent linearity. This curve is used to determine the concentration of a B20 biodiesel/petroleum diesel blend obtained from a local retailer. Excellent precision and accuracy are obtained.     

Soybean biodiesel methyl esters,free glycerin and acid number quantification by 1H nuclear magnetic resonance spectroscopy

Production of alternative fuels, such as biodiesel, from transesterification of vegetable oil driven by heterogeneous catalysts is a promising alternative to fossil diesel. However, achieving a successful substitution for a new renewable fuel depends on several quality parameters. ¹H NMR spectroscopy was used to determine the amount of methyl esters, free glycerin and acid number in the transesterification of soybean oil with methanol in the presence of hydrotalcite‐type catalyst to produce biodiesel. Reaction parameters, such as temperature and time, were used to evaluate soybean oil methyl esters rate conversion. Temperatures of 100 to 180 °C and times of 20 to 240 min were tested on a 1 : 12 molar ratio soybean oil/methanol reaction. At 180 °C/240 min conditions, a rate of 94.5 wt% of methyl esters was obtained, where free glycerin and free fatty acids were not detected. Copyright © 2012 John Wiley & Sons, Ltd.     

Method development for fingerprinting of biodiesel blends by solid-phase extraction and gas chromatography-mass spectrometry

A method based on the combination of solid-phase extraction (SPE) with gas chromatography-mass spectrometry (GC/MS) for detailed chemical fingerprinting of biodiesel/petrodiesel blends was developed in the present study. Forensic identification, commonly referred to as chemical fingerprinting, is based on the relative distributions of individual aliphatic hydrocarbons, aromatic hydrocarbons, fatty acid alkyl esters, and free sterols. Fractionation of fuel samples is optimized for the separation of fatty acid esters and free sterols from petroleum hydrocarbons into four fractions: aliphatic, aromatic, fatty acid ester, and polar components. The final recoveries of aliphatic and aromatic hydrocarbons were determined to be in the range of 65-103%, 73-105% for FAMEs, and 78-103% for free sterols in the polar fraction. Excellent separation with negligible crossover of components with different polarities between fractions was observed. Quantitative analysis of blend levels and individual chemical distribution were achieved. The method has great potential for the identification of biodiesel in diesel fuel blends and could form the basis of a method for characterization of biodiesel-contaminated environmental samples.     

A review of chromatographic characterization techniques for biodiesel and biodiesel blends

This review surveys chromatographic technology that has been applied to the characterization of biodiesel and its blends. Typically, biodiesel consists of fatty acid methyl esters produced by transesterification of plant or animal derived triacylglycerols. Primary attention is given to the determination of trace impurities in biodiesel, such as methanol, glycerol, mono-, di-, and triacylglycerols, and sterol glucosides. The determination of the fatty acid methyl esters, trace impurities in biodiesel, and the determination of the biodiesel content of commercial blends of biodiesel in conventional diesel are also addressed.     

麻疯油转酯化产物的高效液相色谱分析

建立了高效液相色谱法同时测定麻疯油转酯化产物中4种主要脂肪酸甲酯的分析方法。样品经膜处理后用丙酮溶解,采用Hypersil ODS(C18)色谱柱进行分离。以乙腈为流动相进行等度洗脱,内标法定量,同时对色谱条件进行优化。结果表明,在优化的色谱条件下4种脂肪酸甲酯在10 min内得到良好的分离,标准曲线的线性相关系数均达到0.999以上,平均回收率为96%~98%,重现性相对标准偏差为7.2%~10.2%,重复性相对标准偏差为0.31%~2.02%。与气相色谱法相比,该方法具有较高的灵敏度,可用于麻疯油转酯化产物中脂肪酸甲酯含量的测定,为麻疯油转酯化反应制备生物柴油的定性定量分析提供了参考依据。     

生物柴油树种油脂脂肪酸组成对燃料特性的影响

以目前中国主要开发或具有开发潜能的10种生物柴油树种为研究对象,分析其果实或种子油脂脂肪酸组成对合成生物柴油燃料特性的影响。结果表明,木本植物生物柴油产品十六烷值、碘值、氧化安定性等燃料特性主要由原料油脂肪酸的不饱和度决定,脂肪酸不饱和度低于133.13,十六烷值(GB/T 20828-2007)和碘值(EN 14214)就可以达标。生物柴油产品冷滤点随着长碳链饱和脂肪酸的增加而升高,脂肪酸饱和碳链长度因子分别小于8.41和2.72时,可以满足冷滤点0℃和-10℃的要求。高品质生物柴油的原料中应该具有较高的单元不饱和脂肪酸含量。通过油脂脂肪酸单不饱和脂肪酸、多不饱和脂肪酸和饱和脂肪酸的组成绘制出生物柴油特性三角预测图,为预测生物柴油产品燃料特性提供参考依据。     

Production of biodiesel fuel by transesterification of rapeseed oil

Fatty acid methyl esters (FAMEs) show large potential applications as diesel substitutes, also known as biodiesel fuel. Biodiesel fuel as renewable energy is an alternative that can reduce energy dependence on petroleum as well as air pollution. Several processes for the production of biodiesel fuel have been developed. Transesterification processes under alkali catalysis with short-chain alcohols give high yields of methyl esters in short reaction times. We investigated transesterification of rapeseed oil to produce the FAMEs. Experimental reaction conditions were molar ratio of oil to alcohol, concentration of catalyst, type of catalyst, reaction time, and temperature. The conversion ratio of rapeseed oil was enhanced by the alcohol:oil mixing ratio and the reaction temperature.     

Determination of total biodiesel fatty acid methyl, ethyl esters, and hydrocarbon types in diesel fuels by supercritical fluid chromatography-flame ionization detection

A method for determining total biodiesel methyl and ethyl ester content in diesel fuels by supercritical fluid chromatography-flame ionization detection (SFC-FID) is developed. A silica column typically used for determining aromatics in conventional diesel fuels by ASTM D5186 is back-flushed after separation of the hydrocarbons to allow elution of the various esters as a single "total biodiesel" distinct peak. The modification concurrently allows the determination of total aromatic hydrocarbons and their distribution as mono- and polynuclear compounds, as described in the current version of D5186. The instrument response is linear from 1.0% to 50% biodiesel esters with a signal-to-noise ratio of 25 at the 0.1% level. The short-term relative standard is 0.8%. Normalized percent quantitation using a hydrocarbon response factor of 1.00 and an ester response factor of 1.19 provide an average percentage error of 1.8% when measuring actual biodiesel/hydrocarbon fuel blends. The ester response factor is the average of the response factors of 10 pure ester compounds. These responses are calculated from respective solutions of each ester and the four compounds, hexadecane, toluene, tetralin, and naphthalene, as used for the D5186 response factor mixture.     

Production of methyl ester fuel from microalgae

Microalgae are unique photosynthetic organisms that are known to accumulate storage lipids in large quantitites and thrive in saline waters. Before these storage lipids can be used, they must be extracted from the microalgae and converted into usable fuel. Transesterification of lipids produces fatty acid methyl esters that can be used as a diesel fuel substitute. Three solvents, 1-butanol, ethanol, and hexane/2-propanol, were evaluated for extraction efficiency of microalgal lipids. Type of catalyst, concentration of catalyst, time of reaction, temperature of reaction, and quality of lipid were examined as variables for transesterification. The most efficient solvent of the three for extraction was 1-butanol (90% efficiency), followed by hexane/2-propanol and ethanol. Optimal yield of fatty acid methyl esters was obtained using 0.6N hydrochloric acid in methanol for 0.1 h at 70°C.     

Temperature‐programmed capillary high‐performance liquid chromatography with atmospheric pressure chemical ionization mass spectrometry for analysis of fatty acid methyl esters

A new capillary high‐performance liquid chromatography method with atmospheric pressure chemical ionization mass spectrometry was developed for the analysis of fatty acid methyl esters and long‐chain alcohols. The chromatographic separation was achieved using a Zorbax SB‐C18 HPLC column (0.3 × 150 mm, 3.5 μm) with a mobile phase composed of acetonitrile and formic acid and delivered isocratically at a flow rate of 10 μL/min. The column temperature was programmed simply, using a common column oven. Good reproducibility of the temperature profile and retention times were achieved. The temperature programming during the isocratic high‐performance liquid chromatography run had a similar effect as a solvent gradient; it reduced retention times of later eluting analytes and improved their detection limits. Two atmospheric pressure chemical ionization sources of the mass spectrometry detector were compared: an enclosed conventional ion source and an in‐house made ion source with a glass microchip nebulizer. The enclosed source provided better detectability of saturated fatty acid methyl esters and made it possible to determine the double bond positions using acetonitrile‐related adducts, while the open chip‐based source provided better analytical figures of merit for unsaturated fatty acid methyl esters. Temperature‐programmed capillary high‐performance liquid chromatography is a promising method for analyzing neutral lipids in lipidomics and other applications.     

Simultaneous gas chromatographic determination of methanol and free glycerol in biodiesel

Summary The methanol and free glycerol content of vegetable oil methyl esters used as diesel fuel (biodiesel) is very important in describing the quality of this fuel and is therefore limited by specifications. A previously described GLC method for the determination of free glycerol in biodiesel has been further developed and also allows the simultaneous determination of methanol. Sample preparation includes dissolving in dimethylformamide, silylation with bis-trimethylsilyltrifluoracetamide (BSTFA) and separation on a methylsilicone fluid, coated-capillary column using either FID or MS-detection. Ethanol and 1,4-butanediol were used as internal standards. Both detection systems show sufficient sensitivity for concentrations relevant to biodiesel samples. The recovery was tested using a RME-sample containing known amounts of methanol and glycerol.     

超高效液相色谱法测定生物柴油中的11种脂肪酸及脂肪酸甲酯

建立了采用超高效液相色谱(UPLC)-蒸发光散射检测器(ELSD)测定生物柴油中11种常见的脂肪酸及脂肪酸甲酯含量的方法。这11种常见的脂肪酸及脂肪酸甲酯为豆蔻酸、亚油酸、棕榈酸、油酸、亚麻酸甲酯、硬脂酸、亚油酸甲酯、棕榈酸甲酯、油酸甲酯、芥酸和硬脂酸甲酯。样品经提取后用甲醇溶解,采用Acquity UPLC BEH Phenyl C18柱(100 mm×2.1 mm,1.7 μm)分离,乙腈-水（体积比为3∶1)混合液为流动相进行等度洗脱,采用的ELSD条件为增益80,漂移管温度为45 ℃,载气压力为172 kPa,雾化器为冷却模式,并用外标法进行定量分析。结果表明,在一定的质量浓度范围内,峰面积的对数和质量浓度的对数线性关系良好。与其他检测生物柴油成分的方法相比,该方法简单,分离效果好,速度快,特别是此方法可以同时实现脂肪酸及脂肪酸甲酯的分离,并进行定量分析,能有效测定反应的进行程度,从而满足生物柴油工艺研究的需要。     

Catalytic hydrogenation of fatty acid methyl esters

Catalytic hydrogenation of a mixture of fatty acid methyl esters, which are produced by re-esterification of vegetable (sunflower) oil and are contained in biodiesel fuel, was studied.     

Multivariate near infrared spectroscopy models for predicting the methyl esters content in biodiesel

Biodiesel is the main alternative to fossil diesel. The key advantages of its use are the fact that it is a non-toxic renewable resource, which leads to lower emissions of polluting gases. European governments are targeting the incorporation of 20% of biofuels in the general fuels until 2020.Chemically, biodiesel is a mixture of fatty acid methyl esters, derived from vegetable oils or animal fats, which is usually produced by a transesterification reaction, where the oils/fats react with an alcohol, in the presence of a catalyst. The European Standard (EN 14214) establishes 25 parameters that have to be analysed to certify biodiesel quality and the analytical methods that should be used to determine those properties.This work reports the use of near infrared (NIR) spectroscopy to determine the esters content in biodiesel as well as the content in linolenic acid methyl esters (C18:3) in industrial and laboratory-scale biodiesel samples. Furthermore, calibration models for myristic (C14:0), palmitic (C16:0), stearic (C18:0), oleic (C18:1), linoleic (C18:2) acid methyl esters were also obtained. Principal component analysis was used for the qualitative analysis of the spectra, while partial least squares regression was used to develop the calibration models between analytical and spectral data. The results confirm that NIR spectroscopy, in combination with multivariate calibration, is a promising technique to assess the biodiesel quality control in both laboratory-scale and industrial scale samples.     

Determination of Fatty Acid Methyl Esters in Biodiesel Produced from Yellow Horn Oil by LC

A simple and accurate HPLC method with refractive index detection was developed to determine the main fatty acid methyl esters in biodiesel produced from yellow horn oil. Methyl linoleate, methyl linolenate, methyl arachidate, methyl stearate, methyl palmitate and methyl oleate were separated on a HIQ SIL C18W column using methanol as mobile phase. The method has good repeatability and precision, the intraday and interday RSD for both retention time and peak area was less than 3.2%. The LOD (S/N = 3) and LOQ (S/N = 9) were less than 0.004 and 0.015 mg mL⁻¹, respectively.     

Determination of Trace Levels of Fatty Acid Methyl Esters in Aviation Fuel by GC × GC–FID and Comparison with the Reference GC–MS Method

Due to the negative impact of the presence of fatty acid methyl esters in kerosene for the aviation industry, in this work a comprehensive two-dimensional gas chromatography method with flame ionization detector for the determination of trace levels of fatty acid methyl esters in kerosene was developed. It is based on the use of a first dimension polar column and a second dimension non-polar column. Identification of fatty acid methyl esters is based on retention times and the external standard calibration is used for quantitation. Results were compared with those obtained from the GC–MS reference method; good recoveries, close to 100 %, and limit of detection in a range from 3 to 6 μg kg⁻¹ were found without requiring a specific detector.

     

Evaluation of a glycerol derived biofuel by thermal analysis

This work describes thermal analysis evaluation of a glycerol derived compound (fatty acid esters of (2,2-dimethyl-1,3-dioxolan-4-yl) methanol) developed to work as a biofuel. Mixtures of these ketal–glyceryl esters with fatty acid methyl esters typical of soybean biodiesel were prepared and evaluated in relation to biodiesel critical thermal properties such as temperature of crystallization, thermal stability and volatilization measured by differential scanning calorimetry and thermogravimetric analysis. The volatility of the products containing fatty acid methyl esters and (2,2-dimethyl-1,3-dioxolan-4-yl) methyl esters could be predicted by thermogravimetric analyses conducted in nitrogen that avoided time consuming distillation and greatly reduced material expenditure.     

Improved gas chromatographic method for the determination of the individual free fatty acids in cheese using a capillary column and a PTV injector

Summary A gas chromatographic method with a capillary column and a programmed temperature vaporizer injector has been used to analyze the individual free fatty acids in cheese. The lipids were extracted from an acidified cheese slurry with diethyl ether and treated with tetramethylamonium hydroxide (TMAH) to convert the free fatty acids to tetramethylammonium soaps (TMA-soaps), which were subsequently pyrolyzed to methyl esters in the injector. Carrying out injection at the initial column temperature resulted in lower dispersion of the results, but the solvent front prevented quantitative determination of butyric and caproic acids, and an injector temperature of 300°C was therefore employed. Under the conditions tested, trimethylamine (tma) flash-off did not affect the determinations. The accuracy of the method improved at higher free fatty acid contents (coefficient of variation of 0.53% for a total free fatty acid content of 9000 mg/kg as opposed to 7.0% for a total free fatty acid content of 1400 mg/kg). The recovery rate for individual free fatty acids ranged between 91 and 103%.