苯乙烯基噻吩单体及对应的聚脲烷的合成及其非线性光学性能

一种新型的反式-7-[4-N,N-二(β-羟基乙基胺基苯)]-3,5-二硝基乙烯基-噻吩(HBDT)单体分子及对应的预聚物和聚脲烷被合成和表征.由于噻吩环的电子去局域化能量低于苯环,在受授有机共轭化合物中噻吩环比苯环表现出更有效的共轭和更高的非线性,同时也能使目标分子保持好的光、热稳定性.该单体分子及其对应的聚脲烷在普通有机溶剂中具有良好的可溶性,聚脲烷膜具有好的热稳定性.制备了高质量的聚脲烷膜并进行了电晕极化.单体在甲醇中的紫外可见吸收峰(530nm)与对应未经电晕极化聚脲烷膜的吸收峰基本上没有改变.通过溶剂变色法及简并四波混频(DFWM)法测试了单体的二阶和三阶非线性极化率,其β_μ,χ⁽³⁾和γ值分别为8.443×10^-45esu,1.016×10^-12esu(c=3.96×10^-3mol/L),3.93×10^-32esu.     

芪类分子掺杂极化聚合膜的非线性光学性质

采用实时测量光学二次谐波产生（SHG）和吸收光谱的方法时芪类有机分子DANS（4’－N,N－dimethylamino－nitrostilbene）及一种新合成的经氰基团修饰的有机分子CNDS（α’－cyano－4’－nitro－4－N,N－dimethylaminostilbene）掺杂PMMA[poly（methylmethacrylate）]极化聚合膜的非线性光学性质进行了研究。在电晕极化条件下,由于聚合膜的电导率随温度的变化急剧增加,实验中发现两种掺杂极化聚合膜的最佳电导极化温度均低于它们的玻转温度Tg．在最佳极化条件下,从极化前和极化后的吸收光谱变化可看出CNDS的有序度较DANS的差．但实时SHG表明,CNDS／PMMA极化掺杂聚合膜的二阶非线性系数X（2）较DANS／PMMA极化聚合膜的大．结合极化前和极化后吸收峰强度的变化,我们得到CNDS分了的非线性极化率β约为140×10-30esu.在撤离极化场后,CNDS／PMMA的SHG强度的弛豫也比DANS／PMMA慢,说明CNDS是一种性能较DANS优越的制备二阶光学非线性的掺杂分子．     

新型双重电荷转移分子的二阶非线性光学性质的 理论研究

以INDO/SCI方法为基础,按完全态求和(SOS)公式编制了计算分子二阶非线性光学系数β~i~j~k和β~μ的程序。研究了1,2-二氨基-4,5-二硝基苯1和其异构体1,3-二氨基-4,6-二硝基苯2的电子光谱和二阶非线性光学性质。计算表明分子1具有与分子2几乎相等的二阶非线性极化率。但由于分子1的偶极矩明显大于分子2的,故分子1的μβ值比分子2的μβ值大的多。在此基础上,研究了2,3-二(β-苯乙烯基)-5,6-二氰基吡嗪和2,3-二(β-噻吩乙烯基)-5,6-二氰基吡嗪和2,3-二(β-噻吩乙烯基)-5,6二氰基吡嗪衍生物的电子光谱和二阶非线性光学性质。结果表明,这些化合物均具有两个相距很近的强吸收峰,它们对β值的呈加和模式。由于这类化合物特征吸收峰均位于413nm以下且具有大的μβ值,所以,它们是一类很有前途的二阶非线性光学候选材料。     

二芳基氨(硼)-π-碳硼烷三元化合物的二阶非线性光学性质的理论研究

采用密度泛函理论(DFT)方法对二芳基氨(硼)-π-十二顶点碳硼烷三元化合物的结构及二阶非线性光学(NLO)性质进行计算.结果表明,化合物共轭桥长度及二芳基氨(硼)对化合物偶极矩的影响较小.随着分子共轭桥的增长,分子的电子空间范围R2增大,从而使极化率和第一超极化率增大.通过分析化合物的电子光谱和对应的分子轨道组成可知,分子中电荷转移主要发生在二芳基氨(硼)和π-桥之间,碳硼烷的贡献较少.二芳基氨和二芳基硼的供电子能力差异可以调节分子的二阶NLO响应.     

洛汾碱衍生物的电子结构及光谱性质的理论研究

采用密度泛函理论(DFT)的B3LYP/6-31G*方法,对4种洛汾碱类化合物的几何构型进行了优化,在此基础上计算分子的电子结构,并结合有限场FF方法研究了二阶非线性光学(NLO)性质.用含时密度泛函理论(TD-DFT)对上述化合物分子进行吸收光谱的研究.研究表明在4,5-二-苯基-2-对甲酰苯基咪唑生色团中4,5苯环上引入硝基和3位N原子引入苄基改变分子的共轭平面,使二阶非线性极化率总有效值(βtot)减小,吸收峰总体蓝移.同时还发现,在CH2Cl2溶剂中a和c分子的λmax主要来源于HOMO→LUMO的π一π*跃迁,b和d分子的λmax主要来源于HOMO→LUMO+2的π→π*跃迁.     

噻唑类二阶非线性光学活性分子的合成与性能

合成了4个以噻唑环为母体、含有Schiff碱结构的新型二阶非线性光学(NLO)活性分子,用红外光谱、紫外光谱、核磁共振光谱和元素分析确定了分子结构,用溶致变色法确定了二阶极化率. 分子中噻唑五元杂环和Schiff碱结构提高了NLO分子的热稳定性和透明性,噻唑的共轭芳香杂环非中心对称结构连接多个供、吸电子基团,提高了分子的二阶非线性系数. 结果表明,这些NLO分子的紫外吸收波长在350～415 nm之间,裂解温度均在300 ℃左右,二阶非线性光学系数β值达到1×10 -30 esu数量级,初步实现了"二阶非线性-透明性-热稳定性"综合性能优化的目标.     

含2-N,N-二甲氨基嘧啶环与噻吩环结构的共轭聚合物的合成及其性能

合成了一种新型单体2-N,N-二甲氨基-4,6-二氯嘧啶(ADNP).以二氯-1,3-双(二苯基磷)丙烷基镍(Ⅱ)作催化剂,通过2,5-二溴噻吩格氏试剂与该单体共聚得到了一种新型共轭聚合物,聚[(2-N,N-二甲胺基嘧啶-4,6-二)-2,5-噻吩](PThPm).采用FT-IR、1H-NMR等测试手段对新型单体与共聚物的结构进行了表征,并用UV-Vis、荧光光谱、X射线衍射、循环伏安、热重分析(TGA)等测试方法对单体和共聚物进行了性能分析.结果表明:共聚物在420 nm处出现UV-Vis吸收峰,在528 nm处出现荧光发射峰;共聚物的DMF溶液存在酸致变色现象,加入CF3COOH和CH3SO3H后,溶液由淡绿黄色转变为淡红色,UV-Vis吸收峰发生红移;PThPm共聚物有一定的结晶性和热稳定性;在-1.8～ 1.8 V之间出现电致变色现象,电极周围的溶液颜色从深蓝色变成深红色.     

结构规整有序的寡聚噻吩修饰9,9′-螺二芴衍生物的光物理性质及其电化学聚合(英文)

研究了结构规整有序的寡聚噻吩修饰的9,9′-螺二芴衍生物在溶液中和在固体膜状态下的光物理性质,发现在四氢呋喃的稀溶液中,随着有效共轭长度的增加这些化合物的最大吸收峰和发射峰发生了明显的红移.实验结果表明,9,9′-螺二芴骨架中的9位螺碳原子明显地阻断了二个共轭片段的共轭效应,使它们成为了二个独立的共轭链节.此外,还进一步研究了这些化合物的电化学聚合性质.     

联吡嗪为中心的有机共轭杂环分子二阶NLO性质

采用密度泛函理论B3LYP/6-311G**方法,对一系列以联吡嗪为中心的有机共轭杂环分子的二阶非线性光学(NLO)性质和电子光谱进行了研究.结果表明,分子两侧给、受体取代基推或拉电子能力的增大,五元共轭杂环吡咯,呋喃以及噻吩环的引入明显地提高分子的二阶NLO系数βtot值,且降低了分子的最大吸收波长λmax,从而有利于解决"非线性与透光性"的矛盾.该系列分子由于具有较大的βtot值,较好的透光性,可以作为潜在的NLO材料.     

一种新型低带隙共轭聚合物的合成及其光学性质

在钯催化剂作用下, 通过4,7-二(5-溴-2-噻吩基)[2,1,3]苯并噻二唑与2,5-二乙炔基-3-辛基噻吩的偶联反应, 合成了一种新的共轭高分子聚4,7-二(2-噻吩基)苯并噻二唑-3-辛基噻吩二炔(PTE-DTBT). 通过紫外可见吸收光谱及荧光光谱对其光学性质进行了研究. 紫外-可见吸收谱结果表明, PTE-DTBT的固体膜光学带隙为1.71 eV; 电化学测试其带隙为1.88 eV. TiO₂/PTE-DTBT共混固体膜的荧光发射谱结果表明电子供体PTE-DTBT分子与电子受体TiO₂分子间存在有效的电子转移.     

SYNTHESIS AND CHARACTERIZATION OF A NOVEL STYRYLTHIOPHENE MONOMER AND CORRESPONDING POLYURETHANE FOR NLO MATERIALS

A novel monomer, (trans)-7-[4-N,N-(di-β-hydroxyethyl) amino-benzene]-ethenyl-3,5-dinitro-thiophene (HBDT), was synthesized and characterized. The details of synthesizing the monomer andprepolymer, polyurethane with the monomer covalently incorporated are presented. The prepolymer andpolyurethane exhibited good solubility in common organic solvents. Molecular nonlinear optical properties ofthe monomer (HBDT) substituted thiophene based stilbenes is presented.     

一种耐高温聚噻吩膜的电化学合成

聚噻吩及其衍生物具有高的电导率、良好的环境稳定性以及易于调控的分子链结构,因此一直受到人们的广泛关注．但是,这类材料的耐温性能较差,从而将影响其在有机电子器件中的应用．     

功能化线型聚氨酯的合成及其二阶非线性光学特性的研究

功能化线型聚氨酯的合成及其二阶非线性光学特性的研究＊颜星中陈用烈梁兆熙＊＊（中山大学高分子研究所广州５１０２７５）蔡志岗杨佩青徐志凌李鹏（中山大学国家超快速激光光谱重点实验室广州５１０２７５）关键词４’－（Ｎ，Ｎ二羟乙基）－氨基－４－硝基偶氮苯，聚氨...     

The Preparation and Properties of Polyurethane/Nano-CeO<Subscript>2</Subscript> Hybrid Aqueous Coating

To improve the ultraviolet resistance and thermal stability of waterborne polyurethane, stable waterborne polyurethane/nano-cerium oxide hybrid dispersions were obtained by adding nano-cerium colloids to previously synthesized waterborne polyurethane dispersions. The dried ceria colloid was characterized by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). The XRD results indicated the prepared CeO₂ was a face-centered cubic structure. The prepared polyurethane/CeO₂ dispersions were studied by dynamic light scattering (DLS), transmission electron microscopy (TEM), UV–Vis spectroscopy and accelerated weathering test. The dried polyurethane/CeO₂ films were characterized using thermogravimetric analysis (TGA). The DLS analysis indicated the particles average diameter of hybrids emulsion was bigger than that of the pure waterborne polyurethane dispersion. TG analysis and accelerated weathering test suggested the hybrid latex films had better thermal stability and mechanical properties than those of the pure waterborne polyurethane. The UV–Vis absorption capacity of the dispersions prepared was increasing with the amount of CeO₂ colloid increased.     

含异山梨醇结构单元聚酰亚胺的合成与表征

以异山梨醇为原料,合成了含异山梨醇的二胺单体.将该单体与4,4′-(六氟异丙基)双邻苯二甲酸二酐(6FDA)反应,制备了含异山梨醇结构单元的聚酰亚胺.采用红外光谱、氢核磁共振、紫外光谱和热分析等手段,对产物的结构、热性能及光学性能等进行了表征.结果表明,所得到的聚酰亚胺具有较好的热稳定性和光学性能、并在极性溶剂中具有较好的溶解性.     

Preparation, Curing Reactivity and Thermal Properties of Titanium-doped Silicone Resins

Novel titanium-doped silicone resins were synthesized from low-cost silane monomers and tetrabutyl titanate as raw materials and hydrochloric acid as catalyst, with titanium element as dopant into principal chain of Si-O-Si. The resins were characterized by means of FTIR, 1 H NMR and 13 C NMR spectra, their thermal properties and curing properties were investigated and their corresponding films were determined. The results show that the thermal stability and storage stability of the resins were influenced by the types of silane monomers containing different carbon atomicities of organic group. The thermal stability of the titanium-doped silicone resin with a molar ratio of silane monomer B(n-propyl triethoxysilane) to silane monomer C(n-octyl triethoxysilane) being 1:1 is superior to that of the resin with a molar ratio of silane monomer B to silane monomer C being 1:3. However, the storage stability of the former is inferior to that of the latter.This work also showed that the synthesized titanium-doped silicone resins have the highest thermal stability up to 450―500 °C with an atomicity molar ratio of 1:4 of titanium to silicon in the reactants. But the best storage stability of the resin prepared from the reactants with an atomicity molar ratio of 1:6[n(Ti):n(Si)] was obtained. The effect of the type and content of curing agent on the curing properties of the resin was also studied. Moreover, thermal mechanism and curing mechanism were proposed in this work.     

Fluorene-bridged polyphenylquinoxalines with high solubility and good thermal stability: Synthesis and properties

<正>A novel fluorene-bridged tetraketone monomer,9,9-bis[(4-benzilyloxy)phenyl]fluorene(FLTK) was synthesized and characterized.The tetraketone was polymerized with various aromatic tetraamines to afford a series of polyphenylquinoxalines(PPQs).The obtained polymers were found to be soluble in common organic solvents such as N-methyl-2-pyrrolidone(NMP),chloroform and m-cresol.Flexible and tough PPQ films obtained by spin-casting their NMP solutions exhibited tensile strengths higher than 60 MPa.The films also demonstrated good thermal stability up to 500℃in nitrogen and glass transition temperatures higher than 280℃.In addition,the PPQ films exhibited good hydrolytic stability. High surface and volume resistivity retentions were achieved for the films after immersion or boiling in water for 24 h.     

Synthesis and characterization of fluorinated polyurethane containing carborane in the main chain: Thermal,mechanical and chemical resistance properties

In this study, two fluorinated polyurethanes(FPU) containing carborane groups in the main chains were firstly designed and synthesized via the reaction of hexamethylene diisocyanate trimer(HDI trimer) with fluorinated polyesters(CFPETs) having hydroxyl-terminated carborane groups at room temperature. The structures of carborane fluorinated polyesters(CFPETs) and polyurethanes(CFPUs) were characterized by gel permeation chromatography(GPC), Fourier transform infrared(FTIR) spectroscopy and nuclear magnetic resonance(NMR) measurements. The thermal stability, mechanical properties, Shore A hardness, solvent resistance and acid-alkali resistance of the carborane fluorinated polyurethane films were also studied. Thermogravimetric analysis(TGA) tests manifested that the introduction of carborane groups into the main chain of fluorinated polyurethane endowed the obtained fluorinated polyurethane with excellent thermal stability. The thermal decomposition temperature of carborane fluorinated polyurethane(CFPU) increased by 190 °C compared with that of the carborane-free fluorinated polyurethane(FPU). Even at 800 °C, CFPU showed the char yield of 66.5%, which was higher than that of FPU(34.3%). The carborane-containing fluorinated polyurethanes also showed excellent chemical resistance and prominent mechanical property even after the cured films being immersed into Jet aircraft oil or 37% HCl for 168 h or at high temperature(700 °C). It is found that the structural characteristics of carborane group and the compacted structure of CFPU effectively improve the thermal stability, mechanical property, solvent resistance and acid-alkali resistance of the carborane-free fluorinated polyurethane. These excellent properties make CFPU as the useful raw materials to prepare the high temperature resistant coatings or adhesives for automotive engines, engine or fuel tank of aircraft and other equipment working in high-temperature or high concentrations of acid-alkali environments.     

Synthesis and characterization of new semifluorinated linear and hyperbranched poly(arylene ether phosphine oxide)s through B2 + A2 and AB2 approaches

A new phosphorus containing trifluoromethyl-activated bisfluoro B₂ monomer has been synthesized successfully by coupling reaction of 4-methoxyphenylphosphonic dichloride and the Grignard salt of 5-bromo-2-fluorobenzotrifluoride. This monomer was converted to linear poly(arylene ether phosphine oxide)s by nucleophilic displacement of the fluorine atom on the benzene ring with several diphenols. The B₂ monomer was further demethylated to form an AB₂ monomer which on self condensation yielded hyperbranched poly(arylene ether phosphine oxide) with identical phosphorous containing moiety. The products obtained exhibit weight-average molecular weights as high as 600,000 g mol⁻¹ in SEC. These linear and hyperbranched poly(arylene ether phosphine oxide)s showed thermal stability as high as 516 °C for 10% weight loss in TGA in nitrogen and showed glass transition temperatures up to 253 °C in DSC. All the polymers were soluble in a wide range of organic solvents, e.g., CHCl₃, THF, NMP and DMF, however, the hb sample showed a significant lower solution viscosity compared to linear samples of similar molar mass. Transparent thin films of linear poly(arylene ether phosphine oxide)s casted from dichloromethane exhibited tensile strengths up to 50 MPa, a modulus of elasticity up to 0.95 GPa and elongation at break up to 36% depending on their exact repeating unit structures. No free standing films could be prepared from the hb analogue due to the missing entanglements, but stable thin polymer films on silicon wafers with high hydrophobicity were formed which showed water contact angles as high as 91°.