Specific extraction of chromium as tetrabutylammonium-chromate and spectrophotometric determination by diphenylcarbazide: speciation of chromium in effluent streams.

A very specific, selective, simple, and inexpensive procedure was developed for the speciation of CrVI and CrIII. This method is based on the quantitative extraction of chromate and CrIII (previously oxidized to CrVI) as a tetrabutylammonium-chromate ion-pair in methyl isobutyl ketone (MIBK), and then back extraction and preconcentration with an acidic diphenylcarbazide (DPC) solution. Back extraction was applied to achieve further preconcentration by a final factor of 20. The CrVI-DPC complex was determined in back-extract by a spectrophotometer at 548 nm. Under these extraction conditions, most of the probable concomitant cations and anions remained in the first inorganic phase. The calibration curve was linear up to 0.14 microg L(-1) of CrVI with a detection limit of 2.22 ng L(-1). The developed procedure was found to be suitable for the determination of the CrVI and CrIII species in various natural water samples with a relative standard deviation of better than 1.6%. The method was successfully applied to the speciation of chromium in spiked natural water samples, and also samples of effluent from a leather treatment plant.     

Continuous ultrasound-assisted extraction of hexavalent chromium from soil with or without on-line preconcentration prior to photometric monitoring

A continuous ultrasound-assisted extractor was coupled to a photometric detector in order to obtain a fully automated approach for the determination of CrVI in soil. The use of a flow injection (FI) manifold as interface between the extractor and the photometric detector allowed the monitoring of CrVI after extraction in a continuous manner. The coloured complex formed between 1,5-diphenylcarbazide (DPC) and CrVI was used as recommended in EPA method 7196A because it is one of the most sensitive and selective reactions for CrVI determination. A preconcentration minicolumn packed with a strong anion-exchange resin was placed between the extractor and the detector, providing a more sensitive method. The linear dynamic ranges were 1-10 and 0.25-7.5 mg l-1 for the methods without (method A) and with preconcentration (method B), respectively. The limits of detection were 4.52 ng for method A and 1.23 ng for method B. Both methods were applied to a natural contaminated soil and the results obtained agreed well with those obtained by the reference EPA method 3060A. The influence of different amounts of CrIII in the samples was also studied and the results showed that the proposed methods did not disturb the original species distribution.     

Anion-exchange high-performance liquid chromatography of water-soluble chromium (VI) and chromium (III) complexes in biological materials

A high-performance anion-exchange liquid chromatograph coupled to visible-range (370 nm) and UV (280 nm) detectors and an atomic-absorption spectrometer allowed the rapid determination of CrVI and/or complexes of CrIII in rat plasma, erythrocyte lysate and liver supernatant treated with CrVI or CrIII in vitro. CrVI in the eluates was determined using both the visible-range detector and atomic-absorption spectrometer (AAS). The detection limits of CrVI in standard solutions using these methods were 2 and 5 ng (signal-to-noise ratio = 2), respectively. Separations of the biological components and of CrIII complexes were monitored by UV and AAS analyses, respectively. Time-related decreases of CrVI accompanied by increases in CrIII complexes were observed, indicating the reduction of CrVI by some of the biological components. The reduction rates were considerably higher in the liver supernatant and erythrocyte lysate than in the plasma. These results indicate that the anion-exchange high-performance liquid chromatographic system is useful for simultaneous determination of CrVI and CrIII complexes in biological materials.     

Kinetics and mechanism of oxidation of (ethylenediaminediacetato)chromium(III) by N-bromosuccinimide

The kinetics of oxidation of (ethylenediaminediacetato)-chromium(III), [Cr(EDDA)(OH2)2]+, by N-bromosuccinimide (NBS) in aqueous solution to yield CrVI have been studied spectrophotometrically over the 20–40°C range. The reaction rate is first order with respect to both [NBS] and [CrIII], and increases with pH over the range 4.8–5.8. The activation parameters were calculated. A mechanism in which deprotonated [CrIII(EDDA)(OH2)(OH)] is the reactive species is suggested. The electron transfer may proceed via an inner sphere mechanism through bridging of the two reactants by the hydroxo ligand.     

Polyacrylic acid-modified alumina for solid-phase extraction and preconcentration of trace iron and chromium from plant samples

A new method is presented for simultaneous preconcentration of trace Fe(III) and Cr(III) by using polyacrylic acid-alumina as a sorbent. The separation/preconcentration conditions of analytes were investigated, including effect of pH, flow rate, elution conditions, sample volume, and interfering ions. At pH 4, the maximum sorption capacities of Fe3+ and Cr3+ were 8.0 and 13.0 mg/g, respectively, by the column method. The linearity was maintained in the concentration range of 0.175-6.0 x 10(3) ng/mL for iron and 0.175-8.0 x 10(3) ng/mL for chromium in the original solution. The RSD values under optimum conditions were +/- 1.73 and +/- 1.28% for 2.0 microg/mL Fe and Cr, respectively. The preconcentration factor was 400 for both of the elements, and detection limits were 0.025 and 0.023 ng/mL for Fe and Cr in the original solutions. The proposed method was successfully applied to the determination of trace amounts of Fe and Cr in plant samples.     

The efficiency of alkaline extraction for the recovery of hexavalent chromium (CrVI) from paint samples and the effect of sample storage on CrVI recovery

Workplace exposures to CrVI, a human carcinogen, are significant in spraying operations of chromate-containing paints. Accurate determination of CrVI in paint aerosol air samples is important in assessing a worker's exposure to CrVI. National Institute for Occupational Safety and Health method 7604 is widely used for determining CrVI in air samples. It utilizes an alkaline extraction procedure. It was historically validated for paint aerosol samples containing 24.5 to 61.5 microg of CrVI. The literature documented potential airborne CrVI exposures greater than 61.5 microg in recent paint spraying operations. The efficiency of the alkaline method at extracting CrVI from paint samples containing 250 to 3000 microg of CrVI was determined. Paint was prepared, sampled, extracted twice and then digested. Extracts were analyzed for CrVI and digestates of the residual Cr were analyzed for total Cr. Alkaline extraction of paint samples using NIOSH method 7604 resulted in quantitative recoveries for paint samples with CrVI filter loadings from 250 to 3000 microg. A decrease in CrVI extraction efficiency was observed in samples containing > 1000 microg of CrVI. A second extraction improved the recovery of CrVI in these samples. Refrigerating paint aerosol samples for up to 2 weeks did not affect their CrVI content.     

Determination of low concentrations of benzene in urine using multi-dimensional gas chromatography

A method for the determination of benzene in urine of occupationally or environmentally exposed persons was developed. The method was based on dynamic headspace, preconcentration on a solid sorbent, followed by thermal desorption and gas chromatographic determination. To achieve sufficient selectivity, we used multi-dimensional gas chromatography in combination with the inexpensive and robust flame ionisation detector. The limit of detection was 7 ng l-1 and the limit of quantification was 23 ng l-1. The linearity was good (correlation coefficient 0.999) in the range examined (20-4000 ng l-1) and the repeatability was 9%. The average recovery at low concentrations (20-400 ng l-1) was 86%. Analysis of a certified reference material of benzene in water, traceable to NIST, did not differ significantly from the certified value. Samples, frozen (-20 degrees C) in glass bottles sealed with Teflon-silicon septa, were stable for 1 year and refrigerated samples (4 degrees C) for at least 1 week. Loss of benzene during the collection and transfer of urine was investigated and found to be acceptable. The method is a cost effective and robust alternative to GC-MS and permits reliable quantification of occupational exposure and, in most cases, also of urine concentrations that can be expected from environmental exposure.     

Differential determination of arsenic(III) and total arsenic using flow injection on-line separation and preconcentration for graphite furnace atomic absorption spectrometry

Arsenic(III) can be quantitatively extracted using sodium diethyldithiocarbamate (NaDDTC) as the complexing agent and C18 reversed phase packing as the column material for solid phase extraction. Arsenic(V) must be reduced to its trivalent oxidation state prior to extraction. A mixture of sodium sulphite, hydrochloric acid, sodium thiosulphate and potassium iodide was found to be optimum for on-line reduction. When the sorbent extraction is carried out without and with the addition of the reduction mixture, arsenic(III) and total arsenic can be determined sequentially by graphite furnace atomic absorption spectrometry with detection limits (3 σ) of 0.32 ng for As(III) and 0.43 ng for total arsenic. A 7.6-fold enhancement in peak area compared to direct injection of 40 μl samples was obtained after 60 s preconcentration. Results obtained for sea water standard reference materials, using aqueous standards for calibration, agree well with certified values. A precision of 5.5% RSD was obtained for total arsenic in a sea water sample (1.65 As). Results obtained for synthetic mixtures of trivalent and pentavalent arsenic agreed well with expected values.     

Preconcentration procedures for the determination of chromium using atomic spectrometric techniques: A review

Chromium is one of the regulated toxic metals in the environment. Naturally, this element exists mainly in two oxidation: Cr(III) and Cr(VI). In general, Cr(VI) is more toxic than Cr(III). Cr(VI) affects human physiology, accumulates in the food chain and causes severe health problems ranging from simple skin irritation to lung carcinoma. Hence, the determination of chromium traces as well as its speciation in environmental samples is a very important task. In recent years, several preconcentration methods such as coprecipitation, liquid-liquid extraction, dispersive liquid-liquid microextraction, cloud point extraction, and solid phase extraction have been developed and widely used. The aim of this study is to review the recent literature (mainly last 5 years) on the preconcentration technologies those have been used in chromium removal before the determination step by atomic spectrometric techniques. Their advantages and limitations in application are also evaluated.     

An optimised single-reagent method for the speciation of chromium by flame atomic absorption spectrometry based on surfactant micelle-mediated methodology

The toxicity of chromium in the environment is dependent on the species in which it exists. This paper outlines a method for the analysis of the oxidation states of Cr employing a suitable chelating agent and the cloud point phenomenon for Cr(VI) and total Cr analysis. The method involves preconcentration of metal chelates followed by air-acetylene flame atomic absorption spectrometric analysis. The chelating agent chosen for this task is the ammonium pyrrolidinedithiocarbamate, which reacts with either Cr(VI) or total Cr under specific experimental conditions. The condensed surfactant phase with the metal chelate(s) is introduced into a flame atomic absorption spectrometer, whereby discrimination of Cr species is feasible by calculating the Cr(III) concentration from the difference between total Cr and Cr(VI). A multivariate design was employed to study the variables affecting the overall analytical performance for total Cr assay. The analytical curves are rectilinear up to 100 micrograms l-1 for both oxidation states of the metal. The limits of detection are 0.6 microgram l-1 and the relative standard deviation (n = 5) at a concentration of 30 micrograms l-1 for both species is around 2.0%. The method was validated by analysing BCR 544 reference material certified for both Cr species. High recoveries in the range 96-107% were attained for the environmental and biological samples tested.     

Speciation and determination of chromium ions by dispersive micro solid phase extraction using magnetic graphene oxide followed by flame atomic absorption spectrometry

A selective, simple and fast dispersive micro solid phase extraction method using magnetic graphene oxide (GO) as an efficient sorbent has been developed for the extraction, separation and speciation analysis of chromium ions. The method is based on different adsorption behaviour of Cr(VI) and Cr(III) species onto magnetic GO in aqueous solutions which allowed the selective separation and extraction of Cr(VI) in the pH range of 2.0–3.0. The retained Cr(VI) ions by the sorbent were eluted using 0.5 mL of 0.5 mol L^?1 nitric acid solution in methanol and determined by ?ame atomic absorption spectrometry. Total chromium content was determined after the oxidation of Cr(III) to Cr(VI) by potassium permanganate. All effective parameters on the performance of the extraction process were thoroughly investigated and optimised. Under the optimised conditions, the method exhibited a linear dynamic range of 0.5–50.0 µg L^?1 with a detection limit of 0.1 µg L^?1 and pre-concentration factor of 200. The relative standard deviations of 3.8% and 4.6% (n = 8) were obtained at 25.0 µg L^?1 level of Cr(VI) for intra- and inter-day analysis, respectively. The method was successfully applied to the speciation and determination of Cr(VI) and Cr(III) in environmental water samples.     

Solid phase extraction of chromium(VI) using Aliquat336 immobilized on a thin film of multiwall carbon nanotubes

We report on a novel and selective method for the preconcentration and determination of Cr(VI) in aqueous samples. Cr(VI) is adsorbed - in a “batch mode” - on multiwalled carbon nanotubes covered with Aliquat 336 and then determined directly, i.e., on the solid, by X-ray fluorescence spectrometry. This reduces the number of reagents and minimizes sample handling. The method combines the advantages of solid-phase extraction with the benefits of the XRF method in that the large areas required by the carbon nanotubes make them a promising solid sorbent for preconcentration. The enrichment factor was calculated after considering that the thin film obtained from the 10?mL solution of 1?mg?L^?1 of Cr(VI) has a real thickness of 0.04?mm and a final diameter of 16.7?mm, so that the volume deposited on the pellet is 0.0088 cm³ and the preconcentration factor is 1000.

Tea-industry waste activated carbon, as a novel adsorbent, for separation, preconcentration and speciation of chromium

Activated carbon was produced from tea-industry wastes (TIWAC) and employed as a low cost and effective solid phase material for the separation, preconcentration and speciation of chromium species without using a complexing agent, prior to determination by flame atomic absorption spectrometry (FAAS). The characterization of TIWAC was performed by utilizing several techniques such as Fourier Transform Infrared (FTIR) Spectroscopy, Scanning Electron Microscopy (SEM), and elemental analysis. The adsorption experiments were conducted in a batch adsorption technique. Under the experimental conditions, Cr(VI) adsorption amount was nearly equal to zero, however the adsorption percentage of Cr(III) was in the range of 95–100%. Therefore total chromium was determined after the reduction of Cr(VI) to Cr(III) and Cr(VI) was calculated by subtracting Cr(III) concentration from total chromium concentration. The suitable conditions for adsorption and speciation processes were evaluated in terms of pH, eluent type and volume, TIWAC concentration, adsorption and desorption contact time, etc. Adsorption capacity of TIWAC was found to be 61.0 mg g⁻¹. The detection limit for Cr(III) was found to be 0.27 μg L⁻¹ and the preconcentration factor was 50 for 200 mL of sample volume. The procedure was applied to the determination and speciation of chromium in stream, tap and sea water. Also, the proposed method was applied to total chromium preconcentration in microwave digested tobacco and dried eggplant samples with satisfactory results. The method was validated by analyzing certified reference materials (CRM-TMDW-500 Drinking Water and CRM-SA-C Sandy Soil C) and the results were in good agreement with the certified values.     

Speciation analysis of chromium in natural water samples by electrothermal atomic absorbance spectrometry after separation/preconcentration with nanometer zirconium phosphate

A sensitive and simple method for the electrothermal atomic absorption spectrometry (ETAAS) determination of Cr(III) after separation/preconcentration on a micro-column packed with nanometer sized zirconium phosphate has been developed. Total chromium was determined after the reduction of Cr(VI) to Cr(III) by 10% (m/v) of aqueous ascorbic acid. The limit of detection for Cr(III) was 1.5 ng/L with an enrichment factor of 300. The static adsorption capacity of the sorbent for Cr(III) was 9.34 mg/g. The relative standard deviation was 3.2% (n = 7, c = 10 ng/mL). The method was applied successfully to the determination of Cr(III) and Cr(VI) in natural water samples.     

Chromium(III)-imprinted silica gel for speciation analysis of chromium in environmental water samples with ICP-MS detection

A new chromium(III)-imprinted 3-(2-aminoethylamino) propyltrimethoxysilane (AAPTS)-functionalized silica gel sorbent was synthesized by a surface imprinting technique and was employed as a selective solid-phase extraction material for speciation analysis of chromium in environmental water samples prior to its determination by inductively coupled plasma mass spectrometry (ICP-MS). The prepared Cr(III)-imprinted silica gel shows the selectivity coefficient of more than 700 for Cr(III) in the presence of Mn(II). The static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Cr(III) were 30.5 mg g(-1) and 13.4 mg g(-1). It was also found that Cr(VI) could be adsorbed at low pH by the prepared imprinted silica gel, and this finding makes it feasible to enrich and determine Cr(VI) at low pH without adding reducing reagents. The imprinted silica gel sorbent offered a fast kinetics for the adsorption and desorption of both chromium species. Under the optimized conditions, the detection limits of 4.43 pg mL(-1) and 8.30 pg mL(-1) with the relative standard deviations (R.S.D.s) of 4.44% and 4.41% (C=0.5 ng mL(-1), n=7) for Cr(III) and Cr(VI) were obtained, respectively. The proposed method was successfully applied to the speciation of trace chromium in environmental water samples. To validate the proposed method, two certified reference materials were analyzed and the determined values were in a good agreement with the certified values. The developed method is rapid, selective, sensitive and applicable for the speciation of trace chromium in environmental water samples.     

Calcon-modified silica gel sorbent. Application to preconcentration or elimination of trace metals

Silica gel impregnated with a mixture of Aliquat 336 and Calcon was used as chelating sorbent for preconcentration of metals from dilute aqueous solutions and their separation as well as for additional purification of analytical grade sodium and potassium salts from other metals. The relative capacities of sorbent towards 33 metal ions were determined in the pH range 1-9 as well as the concentrations of hydrochloric and perchloric acid eluting the retained metals. It was found that Calcon was not eluted from sorbent with 5M perchloric and 10M hydrochloric acids. The rate of sorption for Mg, Ca, Cu, Zn, Al, Cr(III) and Fe(III) was also studied and it was found that relatively high flow-rates (up to 5 ml/min) can be used for solutions passed through the column. The sorbent was used for preconcentration of traces of some metals from aqueous solutions before their determination by AAS, for separation of metal ion mixtures by column extraction chromatography and for additional purification of potassium chloride solutions used as supporting electrolyte in determination of some heavy metals by anodic stripping voltammetry.     

Reversed phase StrataTM-X resin as sorbent for automatic on-line solid phase extraction atomic absorption spectrometric determination of trace metals: comparison of polymeric-based sorbent materials

A novel on-line flow injection solid phase extraction method for the preconcentration of trace toxic metals prior determination by flame atomic absorption spectrometry (FI-SPE-FAAS) was developed. The potential application of the hydrophobic reversed phase co-polymer sorbent Strata^TM-X packed into an on-line microcolumn for the quantification of Cd(II), Pb(II), Cu(II) and Cr(VI) was demonstrated for the first time. The method was based on the on-line formation of metal complexes using sodium diethyl-dithiocarbamate (DDTC) and on the subsequent retention of them onto the sorbent material. The target analytes were completely eluted by methanol and, subsequently, directed to FAAS for quantification. All chemical and flow variables affecting the performance of the developed method were thoroughly studied and optimised. For a preconcentration time of 90 s and a sampling frequency of 28 h^?1, enhancement factors of 72, 140, 185, 63 and detection limits of 0.18, 1.6, 0.20 and 1.2 μg L ^?1 were obtained for Cd(II), Pb(II), Cu(II) and Cr(VI), respectively. The accuracy of the FI-SPE-FAAS method was evaluated by analysing certified reference materials as well as spiked environmental water samples. Furthermore, a comparative study of the analytical characteristics, the properties as well as the chemical structures of commercial polymeric based sorbent materials was employed. Strata-X sorbent was compared against Hypersep^TM SCX, Bond Elut® Plexa^TM PCX, Oasis-HLB^TM and Nobias^TM PA-1, regarding the adaptation in on-line FI-SPE-FAAS systems for metal determination, and herein presented.     

Solid phase extraction of hexavalent chromium by Mannich base polymer wrapped flower-like layered double hydroxide

In the present work, synthesis of polymer wrapped flower-like MgAl layered double hydroxide was done through condensation of 1,4 phenylenediamine and resorcinol by p-formaldehyde. The nanocomposite was characterised with X-ray diffraction analysis, fourier transform infrared spectroscopy, thermogravimetric analysis and field emission scanning electron microscopy techniques and employed for effective adsorption of Cr(VI) from aqueous solution prior to flame atomic absorption spectrometer determination. Optimum level of effective parameters (pH, reaction time and adsorbent dosage) and their interaction was determined by response surface methodology. To investigate applicability of method for trace heavy metal adsorption, the method was employed for preconcentration of Cr(VI) in water samples. At the optimum conditions, pH = 4.5, shaking time of 15 min and adsorbent dosage of 20 mg, analytical performance of the method was evaluated and results showed that calibration curve is linear in the concentration range of 2–100 μg L^?1. Moreover, limit of detection was 0.22 µg L^?1 and relative standard deviation of six replicate experiments at initial concentration of 0.1 mg L^?1 was 3.3%. Isotherm study showed that Freundlich model can better describe adsorption behaviour as well as the sorbent showed the adsorption capacity of 62.5 mg g^?1. Moreover, thermodynamic study revealed that chromate adsorption was spontaneous and followed the endothermic path. Regeneration of sorbent was performed using 1.0 mol L^?1 of NaOH solution. The sorbent was employed for Cr(VI) determination from food additives and seawater samples.     

Separation,preconcentration and speciation of chromium by solid phase extraction on immobilised ferron

A sensitive and simple method for determination of chromium species after separation and preconcentration by solid phase extraction (SPE) has been developed. For the determination of the total concentration of chromium in solution, Cr(VI) was efficiently reduced to Cr(III) by addition of hydroxylamine and Cr(III) was preconcentrated on a column of immobilised ferron on alumina. The adsorbed analyte was then eluted with 5?mL of hydrochloric acid and was determined by flame atomic absorption spectrometery. The speciation of chromium was affected by first passing the solution through an acidic alumina column which retained Cr(VI) and then Cr(III) was preconcentrated by immobilised ferron column and determined by FAAS. The concentration of Cr(VI) was determined from the difference of concentration of total chromium and Cr(III). The effect of pH, concentration of eluent, flow rate of sample and eluent solution, and foreign ions on the sorption of chromium (III) by immobilised ferron column was investigated. Under the optimised conditions the calibration curve was linear over the range of 2–400?µg?L^?1 for 1000?mL preconcentration volume. The detection limit was 0.32?µg?L^?1, the preconcentration factor was 400, and the relative standard deviation (%RSD) was 1.9% (at 10?µg?L^?1; n?=?7). The method was successfully applied to the determination of chromium species in water samples and total chromium in standard alloys.     

Flow Injection Semi-online Sorbent Extraction Preconcentration for Graphite Furnace Atomic Absorption Spectrometry

A micro-flow injection sorbent extraction preconcentration system was combined with a graphite furnace atomic absorption spectrometer. The combination results in an integrated system for the determination of trace amounts of heavy metals. Silica bonded with octadecyl functional groups (C₁₈) was used as a sorbent in a 15-μL conical microcolumn. The metals to be determined were preconcentrated as diethyl dithiocarbamate chelates onto the column for 60 s and then rinsed with deionized water and eluted with 40 μL of ethanol. Compared with direct injection of 40 μL of aqueous sample solution, enrichment factors of 30, 32, and 29 and detection limits (3ς) of 7.8, 12.8, and 3.9 ng/L for cobalt, nickel, and lead, respectively, were obtained with 60-s sample loading at 3.0 mL/min for sorbent extraction, 40 μL of eluate injection, and peak area measurement. The results obtained for trace amounts of cobalt, nickel, and lead in reference materials showed that there were no significant differences between the certified and determined values.