Approach to the determination of insulin-like-growth-factor-I (IGF-I) concentration in plasma by high-performance liquid chromatography-ion trap mass spectrometry: use of a deconvolution algorithm for the quantification of multiprotonated molecules in electrospray ionization.

The insulin-like-growth-factor-I (IGF-I) peptide is known to be a marker for growth hormone administration. The development of a quantification method by electrospray ionization mass spectrometry (ESI-MS) coupled with high-performance liquid chromatography (HPLC) is required. This paper describes a method to quantify IGF-I using the internal standard R3 IGF-I in its oxidized forms. A deconvolution software was used to quantify the set of multi-charged molecules recorded on an ESI ion trap mass spectrometer. The results (i.e., linearity, reproducibility and concentration range) were obtained on standard samples and the described LC-ESI-MS method should be applicable to biological samples.     

Development of a liquid chromatography-electrospray mass spectrometric method for the simultaneous analysis of benzoxazolinones and their degradation products

A new method for the simultaneous analysis of some benzoxazolinones, aminophenoxazinones and malonamic acids was developed based on liquid chromatography (LC) coupled to mass spectrometry (MS), using electrospray ionization (ESI) and operating in positive mode. Different ESI-MS parameters, such as fragmentor voltage, capillary voltage, drying gas flow, nebulizer gas pressure and drying gas temperature, were optimized in order to obtain structural information and to achieve maximum sensitivity. Chromatographic separation was performed by a reversed-phase LC column using a linear gradient of water and methanol. Quality assurance of the developed method was assessed by measuring parameters as linearity, sensitivity, repeatability and reproducibility. Quantification method based on the use of internal standard was developed, selecting synthetic 2-methoxy-2H-1,4-benzoxazin-3(4H)-one as internal standard. Good correlations were obtained for all analytes relative to this compound in the range of 0.05-1.5 ng/microL. Instrumental detection limits were between 0.02 and 0.2 ng/microL. Repeatability and reproducibility studies showed acceptable coefficient of variation values.     

Isotope measurements in uranium using a quadrupole inductively coupled plasma mass spectrometer (ICPMS)

A series of measurements were carried out to establish the reliability associated with isotope ratio (235/238) measurements on uranium samples using a quadrupole inductively coupled plasma mass spectrometer (ICPMS). Figures of merit related to the isotopic measurements were determined using non certified as well as certified materials provided by the New Brunswick Laboratory (NBL). The experimental results showed that repeatability is around 0.5% while reproducibility was calculated as 0.27%. Mass discrimination was determined as 0.03% per mass unit and the system linearity check over five orders of isotope ratios yielded a mass discrimination factor (K factor) of 1.0002±0.0081 (0.81%, 2s). The mean error of measurement obtained from six different certified reference materials was 0.77%.     

Capillary electrophoresis of polycationic poly(amidoamine) dendrimers

Generation 2 to generation 5 poly(amidoamine) (PAMAM) dendrimers having different terminal functionalities were analyzed by capillary electrophoresis (CE). Polyacrylamide gel electrophoresis was also used to assess the composition of the individual generations for comparison with the CE results. Separation of PAMAMs can be accomplished by either using uncoated silica or silanized silica capillaries, although reproducibility is poor using the uncoated silica capillary. To improve run-to-run reproducibility, silanized capillary was used and various internal standards were also tested. Relative and normalized migration times of primary amine terminated PAMAM dendrimers were then determined using 2,3-diaminopyridine (2,3-DAP) as an internal standard. Using silanized capillaries and internal standards, the relative and normalized migration times are fully reproducible and comparable between runs. Apparent dimensionless electrophoretic mobilities were determined and the results were compared to theoretical calculations. It is concluded that for PAMAMs a complex separation mechanism has to be considered in CE, where the movement of the ions is due to the electric field, but the separation is rather the consequence of the adsorption/desorption equilibria on the capillary wall ("electrokinetic capillary chromatography"). The described method may be used for quality control and may serve as an effective technique to analyze polycationic PAMAM dendrimers and their derivatives with different surface modifications.     

Simultaneous analysis of polyhydroxylated alkaloids by capillary electrophoresis using borate complexation and evaluation of sweeping technique for sensitivity improvement

Summary Capillary zone electrophoresis coupled to UV detection was used for the simultaneous analysis of naturally occurring polyhydroxylated alkaloids. This separation was based on anin-situ complexation with borate ions. The effect of parameters such as borate concentration, capillary temperature and analyte molecular structure on migration times and selectivity were discussed. The best separation was obtained with a fused silica capillary (48.5 cm total length ×50 μm I.D., with a bubble factor of 3), 80 mM sodium tetraborate aqueous solution at pH 9.2 and temperature of 20°C. The method was validated and showed good data in terms of migration time and peak area reproducibility, selectivity, linearity and accuracy. The validated method was applied to determine miglitol in commercially available pharmaceutical tablets. To further improve method sensitivity, a sweeping technique involving borate ions was evaluated. This technique was found very sensitive to the analyte complexation with borate, borate concentration, and temperature as well as sample matrix. In the case of miglitol, a 35-fold improvement in peak height was achieved.     

Systematic comparison of delta34S measurements by multicollector inductively coupled plasma mass spectrometry and evaluation of full uncertainty budget using two different metrological approaches

A systematic comparison of delta34S measurements by multicollector inductively coupled plasma mass spectrometry (MCICPMS) using two different standardisation approaches and two different reference materials as working standards is reported for the first time. Full uncertainty budgets have been calculated using the Kragten approach. Internal standardisation by measuring Si ratios and external standardisation by bracketing samples with either NIST RM8553 or NIST RM8554 have been compared to correct for the effects of mass bias. The delta34S value and the associated uncertainty ( per thousand) were found to be slightly different when using different approaches. Corrected 34S:32S ratios for NIST RM8553 and NIST RM8554 differed from those previously reported by 0.1 to 0.5% when using external standardisation. 34S:32S ratios for NIST RM8553 and NIST RM8554 differed from those previously reported by 0.06 to 0.15% when using Si internal standardisation. This indicated that in order to minimise deviation from true ratio values, Si internal standardisation would be a more appropriate option when using a Neptune MCICPMS instrument. delta(34)S values were obtained for four different methionine samples and expanded uncertainties (k = 2) expressed in delta34S ( per thousand) ranged from 0.7 per thousand to 1.6 per thousand. Regardless of the approach used for the mass bias correction, three parameters provided the major contributions to the standard uncertainty of the delta34S(V-CDT) value. These were the measured 34S:32S in the sample, the measured 34S:32S for the working standard and the known delta34S(V-CDT) value of the working standard. Results using both approaches are compared and the Si internal standardisation approach is used to provide results for an inter-laboratory comparison.     

液相色谱-电喷雾离子阱质谱联用分析河豚毒素

应用C18反相色谱柱和HILIC亲水作用色谱柱,建立了河豚毒素(TTX)的液相色谱-电喷雾离子阱质谱联用分析方法。应用反相色谱法,在选择离子监测(SIM)模式下,对TTX的分析具有良好的线性响应(r=0.9992),方法检出限(S/N=3)为120pg,相对标准偏差(RSD)低于10%;应用亲水色谱法,在SIM和选择反应监测(SRM)模式下同样具有良好的线性响应(r=0.9996和r=0.9998),检出限(S/N=3)分别为15pg和3.75pg,在SIM模式下RSD低于10%,在SRM模式下RSD处于10%~20%之间。亲水作用色谱柱大大提高了方法的灵敏度,由于SIM模式具有较高的精密度,建议应用HILIC色谱柱的SIM模式定量分析TTX。     

Quantitative evaluation of proteins in one- and two-dimensional polyacrylamide gels using a fluorescent stain

The characteristics of protein detection and quantitation with SYPRO Ruby protein gel stain in one- and two-dimensional polyacrylamide gels were evaluated. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) analyses of three different purified recombinant proteins showed that the limits of detection were comparable to the limits of detection with ammoniacal silver staining and were protein-specific, ranging from 0.5 to 5 ng. The linearity of the relationship between protein level and SYPRO Ruby staining intensity also depended on the individual protein, with observed linear dynamic ranges of 200-, 500-, and, 1000-fold for proteins analyzed by SDS-PAGE. SYPRO Ruby protein gel stain was also evaluated in two-dimensional electrophoretic (2-DE) analysis of Escherichia coli proteins. The experiment involved analysis of replicates of the same sample as well as dilution of the sample from 0.5 to 50 nug total protein across gels. In addition to validating the 2-DE system itself, the experiment was used to evaluate three different image analysis programs: Z3 (Compugen), Progenesis (Nonlinear Dynamics), and PDQuest (Bio-Rad). In each program, we analyzed the 2-DE images with respect to sensitivity and reproducibility of overall protein spot detection, as well as linearity of response for 20 representative proteins of different molecular weights and pI. Across all three programs, coefficients of variation (CV) in total number of spots detected among replicate gels ranged from 4 to 11%. For the 20 representative proteins, spot quantitation was also comparable with CVs for gel-to-gel reproducibility ranging from 3 to 33%. Using Progenesis and PDQuest, a 1000-fold linear dynamic range of SYPRO Ruby was demonstrated with a single known protein. These two programs were more suitable than Z3 for examining individual protein spot quantity across a series of gels and gave comparable results.     

Determination of Ritodrine in Plasma Using HPLC

Abstract

An HPLC instrument coupled with an electrochemical detector was used to determine ritodrine (erythro-p-hydroxy-α-[1-[(p-hydroxyphenethyl)-amino]ethyl] benzyl alcohol hydrochloride) at nanogram levels in serum. Extraction of ritodrine was accomplished using a multistep ethyl acetate procedure, and the mobile phase consisted of acetonitrile, ammonium acetate, glacial acetic acid, and a counterion. The stationary phase was a Biophase ODS 5 μm column at ambient temperature. Nalbuphine hydrochloride (Nubain®) was used as an internal standard to quantitate the ritodrine levels of pregnant patients receiving ritodrine. The procedure's linearity for both ritodrine standards and spiked plasma samples was demonstrated. The precision of the assay was found to be 3.4% at 20 ng/ml ritodrine. The minimum detectable concentration, with a signal-to-noise ratio of 6, was determined to be 0.31 ng per 50 μl injected, corresponding to a concentration of 0.6 ng/ml plasma. The sensitivity, precision, and reproducibility of the assay were all found to be acceptable for determining ritodrine in patient serum.     

超级微波消解-电感耦合等离子体发射光谱（ICP-OES）法测定土壤中18种元素

为提高土壤多元素同时检测的效率,采用超级微波消解-电感耦合等离子体发射光谱法测定土壤中钾、钠、钙、镁、铜、铁、锰、锌、磷、硫、硼、砷、镉、铬、铅、钴、镓、锂等18种元素含量。比较了超级微波消解、常规微波消解和电热板消解的处理效果,采用超级微波消解法对样品进行前处理,并优化了消解条件。在最优条件下,各元素的检出限在0.05~20 mg/kg,加标回收率在86.2%~107.5%,RSD在0.1%~3.0%,方法准确度及精密度可以满足多元素同时测定的需求,且该方法具有简单、快速、成本低、用酸量少、重现性好等特点。     

Surface-activated chemical ionization in the analysis of arginine in plasma samples

Alterations of arginine plasma levels are involved in several disorders of amino acid metabolism such as hurtnup, argininosuccinic aciduria, histidinemia, citrullinuria, and cystinuria. In this work a new liquid ionization source, surface-activated chemical ionization (SACI), has been used to analyze arginine in human and rat plasma samples. Arginine was extracted and diluted ten times through protein precipitation. The diluted arginine samples were then analyzed using an ion-exchange chromatographic column coupled with the SACI source and an ion trap analyzer using MS(3) monitoring in order to increase the sensitivity and specificity of the analysis. The multiple-point standard additions method was used to quantify the arginine. This method was employed to eliminate the matrix effect that affects all liquid ionization sources (APCI, ESI, SACI, etc.), and also does not require use of an internal standard. High-quality results in terms of sensitivity, limit of detection, lower limit of quantitation, linearity and reproducibility, are demonstrated.     

Organotin analysis by gas chromatography–pulsed flame-photometric detection (GC–PFPD)

Monobutyltin (MBuT), dibutyltin (DBuT), and tributyltin (TBuT) mixtures have been separated and quantified by gas chromatography with pulsed flame-photometric detection (GC–PFPD). The compounds were first derivatized with NaBEt₄, then extracted with hexane and injected into the GC in splitless mode. Optimum GC and detector conditions were established. For GC, various injector temperatures and oven temperature programs were tested. For the PFPD detector, gate settings (gate delay and gate width) and detector temperature were optimized. A very good linearity was obtained up to 100–150 ppb for all organotin compounds. The detection limits obtained were: MBuT (0.7 ppb), DBuT (0.8 ppb), and TBuT (0.6 ppb). RSD for repeatability and reproducibility were well below 20% when the instrument was in routine operation. A biological sample (CRM 477) was also analyzed for organotins. Extraction from the biological matrix was performed with TMAH. Besides the increased risk of contamination, the derivatization step seemed to be critical. pH and amount of derivatizing agent were tested. When using an internal standard (TPrT) between 90% and 110% of the certified amounts of organotin were recovered.     

A reversed-phase capillary ultra-performance liquid chromatography-mass spectrometry (UPLC-MS) method for comprehensive top-down/bottom-up lipid profiling

Lipidomics is a critical part of metabolomics and aims to study all the lipids within a living system. We present here the development and evaluation of a sensitive capillary UPLC-MS method for comprehensive top-down/bottom-up lipid profiling. Three different stationary phases were evaluated in terms of peak capacity, linearity, reproducibility, and limit of quantification (LOQ) using a mixture of lipid standards representative of the lipidome. The relative standard deviations of the retention times and peak abundances of the lipid standards were 0.29% and 7.7%, respectively, when using the optimized method. The linearity was acceptable at >0.99 over 3 orders of magnitude, and the LOQs were sub-fmol. To demonstrate the performance of the method in the analysis of complex samples, we analyzed lipids extracted from a human cell line, rat plasma, and a model human skin tissue, identifying 446, 444, and 370 unique lipids, respectively. Overall, the method provided either higher coverage of the lipidome, greater measurement sensitivity, or both, when compared to other approaches of global, untargeted lipid profiling based on chromatography coupled with MS.     

Electrospray ionization stability and concentration sensitivity in capillary electrophoresis-mass spectrometry using a flow-through microvial interface

Concentration sensitivity is a key performance indicator for analytical techniques including for capillary electrophoresis-mass spectrometry (CE–MS) with electrospray ionization (ESI). In this study, a flow-through microvial interface was used to couple CE with MS and improve the ESI stability and detection sensitivity. By infusing a peptide mixture through the interface into an MS detector at a typical flow rate for CE-MS analysis, the spatial region near the interface was mapped for MS signal intensity. When the sprayer tip was within a 6 × 6.5 × 5 mm region in front of the MS inlet, the ESI was stable with no significant loss of signal intensity for ions with m/z 239. Finite element simulations showed that the average electric field strength at the emitter tip did not change significantly with minor changes in emitter tip location. Experiments were conducted with four different mass spectrometer platforms coupled to CE via the flow-through microvial interface. Key performance indicators, that is, limit of detection (LOD) and linearity of calibration curves were measured for nine amino acids and five peptides. Inter- and intraday reproducibility were also tested. The results were shown to be suitable for quantification when internal standards were used.     

On-line measurements of delta(15)N in biological fluids by a modified continuous-flow elemental analyzer with an isotope-ratio mass spectrometer

A modified continuous-flow elemental analyzer coupled to an isotope-ratio mass spectrometer (modified EA-IRMS) was tested for on-line delta(15)N measurement on urea solution and biological fluids (e.g. urine). The elemental analyzer configuration was adapted by adding a U-shaped cold trap and an X-pattern four-way valve for on-line trapping/venting of water from the liquid samples. Results indicate that the delta(15)N ratios show little variation (standard deviation (SD) = 0.05 per thousand) with a sample size above the equivalent N yield of 0.2 mg urea (0.092 mg N) when the mass spectrometer conditions were carefully optimized. By contrast, a significant logarithmic decrease in delta(15)N with sample size was observed but this can be offset by applying a linearity correction or blank correction when the sample size is between equivalent N yields of 0.05 and 0.2 mg urea. The blank corrected delta(15)N ratios give an overall precision of approximately 0.16 per thousand whereas the average precision for delta(15)N corrected using combined linearity and shift correction is 0.05 per thousand. The relatively large variation in blank corrected delta(15)N values may be attributed to the variability of the blank delta(15)N in the sequence. Therefore, the blank correction should be carefully performed in routine measurements. As a result, the linearity range of a modified EA-IRMS can be extended to a minimum sample size of 0.023 mg N. In addition, the reproducibility of the new system is good, as indicated by the precision (<0.2 per thousand) for a set of standards and unknowns. The data show that fluids containing nitrogen can be successfully analyzed in the modified EA-IRMS.     

Routine analysis of ultra pure water by ICP-MS in the low- and sub-ng/L level

The chemical analysis with inductively coupled plasma-mass spectrometry (ICP-MS) can help to examine the purity of ultra pure water (UPW) down to 10 part per trillion (ng/L) and lower. For a proper determination of a high number of samples per week the analysis must be divided into two parts: the routine analysis and the reference water analysis. The routine analysis is done by direct measurement of the ultra pure water samples. Applying a standard addition method under particular clean conditions, the reference water analysis leads to the definition of the accurate zero. A quick evaluation scheme is also presented for the reference water analysis. The method is tested for its fitness for application by examining LOD (for relevant element < 2 ng/L), reproducibility and linearity of calibration. The ICP-MS was optimized according to the methodology of G. Taguchi to improve reproducibility and LOD.     

Validation of an inductively coupled plasma-optical emission spectrometry method for the determination of major elements in farmed rainbow trout (<Emphasis Type="Italic">Oncorhynchus mykiss</Emphasis>)

An inductively coupled plasma?optical emission spectrometry method was optimized and validated for the determination of major elements (Ca, K, Mg, Na and P) in cultivated freshwater fish (rainbow trout Oncorhynchus mykiss). The method was validated by analysis of a Certified Reference Material, consisting in a frozen tissue homogenate from lake trout (Salvelinus namaycush namaycush). The linearity of this method was very good, as evidenced by the coefficients of correlation (r) for calibration graphs that were higher than 0.9999 in all cases and by linearity test (response factor <5% and relative calibration graph slope <2%). Accuracy, expressed as relative recovery (%) in comparison with certified concentration ranged from 100 to 109%, and precision, expressed as residual standard deviation (%) ranged from 1.2 to 6.5% (repeatability) and from 1.0 to 9.6% (reproducibility). The limit of quantification ranged from 4 ng/mL (Ca and Mg) to 203 ng/mL (P). The optimized method was applied to major element determination in skin and muscle samples from rainbow trout fillets.     

Identification of 2,3-butanedione (diacetyl) as the compound causing odor events at trace levels in the Llobregat River and Barcelona's treated water (Spain)

A study of organic compounds imparting sweet and buttery odor problems in the Llobregat River (northeast Spain) and in treated water was conducted. Solid-phase microextraction (SPME), gas chromatography-olfactometry, and flavor profile analysis (FPA) were used as analytical methodologies to identify the compound responsible for odor incidents. 2,3-Butanedione (diacetyl) with a concentration range of 0.90-26 microg/l in river water samples entering the water treatment plant was identified as the compound causing the odor events. Flavor profile analysis establishes 0.05 microg/l as its odor threshold concentration (OTC) in water, with an odor recognition concentration of 0.20 microg/l. The analyses were carried out with SPME-GC-MS and parameters affecting SPME extraction such as selection of the fiber (carboxen-polydimethylsiloxane), extraction time (30 min), temperature (60 degrees C), and ionic strength were evaluated. Quality parameters of the optimized method gives good linearity (r2 > 0.999), a limit of detection (0.08 microg/l) similar to the OTC of the compound, and good reproducibility (R.S.D. < 20%). The SPME method was applied to identify the compound causing the odor.     

Pantothenic acid (vitamin B5) in fortified foods: comparison of a novel ultra-performance liquid chromatography-tandem mass spectrometry method and a microbiological assay (AOAC Official Method 992.07)

A novel method was developed and single-laboratory validated for the determination of free pantothenic acid (vitamin B5) in a wide range of infant and adult fortified food products. The method combines simple sample preparation and chromatographic analysis using ultra-performance LC coupled to tandem MS with positive electrospray ionization. Pantothenic acid was quantified using [13C6, 15N2]-pantothenic acid as an internal standard. Calibration curves were linear between 0.08 and 1.2 microg/mL (r2 = 0.9998), and average recovery varied between 95 and 106%. The method exhibited overall RSD(r) of 1.1% and RSD intermediate reproducibility from 2.5 to 6.0% in infant formulas and cereals. Comparison of results between total and free pantothenic acid showed that the analysis of free pantothenic acid gave a good estimation of total pantothenic acid in the range of products analyzed. The method provides reliable free pantothenic acid results in a wide range of fortified foods (infant and adult nutritionals, cereal products and beverages), and shows good correlation with the microbiological method AOAC Official Method 992.07. It is a more selective, faster, and robust alternative to microbiological determination.     

Direct sampling and analysis from solid-phase extraction cards using an automated liquid extraction surface analysis nanoelectrospray mass spectrometry system

Direct liquid extraction based surface sampling, a technique previously demonstrated with continuous flow and autonomous pipette liquid microjunction surface sampling probes, has recently been implemented as a liquid extraction surface analysis (LESA) mode on a commercially available chip‐based infusion nanoelectrospray ionization (nanoESI) system. In the present paper, the LESA mode was applied to the analysis of 96‐well format custom‐made solid‐phase extraction (SPE) cards, with each well consisting of either a 1 or a 2 mm diameter monolithic hydrophobic stationary phase. These substrate wells were conditioned, loaded with either single or multi‐component aqueous mixtures, and read out using the commercial nanoESI system coupled to a hybrid triple quadrupole/linear ion trap mass spectrometer or a linear ion trap mass spectrometer. The extraction conditions, including extraction/nanoESI solvent composition, volume, and dwell times, were optimized in the analysis of targeted compounds. Limit of detection and quantitation as well as analysis reproducibility figures of merit were measured. Calibration data was obtained for propranolol using a deuterated internal standard which demonstrated linearity and reproducibility. A 10× increase in signal and cleanup of micromolar angiotensin II from a concentrated salt solution was demonstrated. In addition, a multicomponent herbicide mixture at ppb concentration levels was analyzed using MS³ spectra for compound identification in the presence of isobaric interferences. Published in 2011 by John Wiley & Sons, Ltd.