共查询到20条相似文献,搜索用时 156 毫秒
1.
传统有效折射率方法只能模拟具有相同空气孔大小的单包层光子晶体光纤.针对这一问题,提出了一种改进的有效折射率法,能够计算具有不同孔径的多包层光子晶体光纤的传输特性.并用此方法对三包层光子晶体光纤的基模有效折射率和色散等特性进行了数值模拟,结果与多极法模拟出的结果符合得很好.这种改进的有效折射率法拓展了传统有效折射率法的适用范围,对快速准确地分析和设计具有不同传输特性的多包层光子晶体光纤提供了理论依据.
关键词:
光子晶体光纤
多包层
有效折射率方法
色散 相似文献
2.
3.
温度对液晶填充光子晶体光纤传输特性的影响 总被引:6,自引:0,他引:6
利用液晶的折射率是温度和波长函数的特性,在光子晶体光纤(PCF)芯区的空气柱中填充向列相液晶,通过改变温度来改变液晶的折射率,构成了一种温度凋制光子晶体光纤.用阶跃有效折射率模型研究了温度对这种光子晶体光纤在不同光波长时传输特性的影响,并进行了数值计算.结果表明液晶填充使光子晶体光纤的色散减小,由于折射率对温度和波长变化敏感,改变温度可以使光纤在长波长区域出现单模传输,在短波长时不会出现单模传输,即使包层相对孔径很小也不会出现无截止单模传输.温度升高使光纤的色散值增大,零色散波长向短波长方向移动.这些特性对温度调制光子晶体光纤器件的设计和应用具有一定的参考意义. 相似文献
4.
等效折射率模型研究光子晶体光纤的色散特性 总被引:20,自引:4,他引:16
应用等效折射率模型对折射率导模光子晶体光纤的群速度色散特性进行了详细的讨论。由于光子晶体光纤由单一材料(SiO2)制成,光纤的波导色散决定了总色散,因此讨论中将群速度色散分解为波导色散和材料色散,研究了波导色散与光子晶体光纤的结构参量孔距∧、相对孔径f的关系。分析表明,在f一定的情况下,光子晶体光纤的波导色散与孔距∧的关系符合麦克斯韦方程的比例性质;而在孔距∧确定的情况下,光子晶体光纤的波导色散的零点、极小值点位置与f在所讨论的波长范围内存在线性关系。最后举例说明了通过调整光子晶体光纤的结构参量,可以灵活地设计其色散特性。 相似文献
5.
6.
通过调节纤芯大小实现接近零色散的色散平坦光子晶体光纤 总被引:1,自引:0,他引:1
利用已有文献对光子晶体光纤色散特性的计算结果,分析了色散随光子晶体光纤结构参数变化的趋势,并利用有效折射率方法基于标量近似理论对光子晶体光纤色散特性进行了有目的性的数值模拟,发现通过独立调整纤芯大小,可以在光通信波段实现非常接近零色散的色散平坦光子晶体光纤,其色散系数D的绝对值在1.3 μm~2.0 μm波长范围小于1.5 ps·km-1·nm-1 . 相似文献
7.
利用矢量有效折射率方法(矢量法)对光子晶体光纤基模的色散特性进行了数值模拟,并与双正交归一基矢量法以及标量有效折射率方法(标量法)的模拟结果进行了对比.发现所用矢量法的结果与双正交归一基矢量法的结果符合很好,而标量法在低空气填充率f或较高归一化波数A/λ时是一种较好的近似,在空气填充率f较高或归一化波数A/λ较低时,要得到精确的结果必须利用矢量法对光子晶体光纤的特性进行模拟.讨论了光子晶体光纤包层有效折射率与光纤结构的关系.
关键词:
光子晶体光纤
矢量法
有效折射率
色散 相似文献
8.
9.
10.
一维光子晶体非线性色散特性的分析 总被引:10,自引:8,他引:2
从无限周期一维光子晶体的色散关系和有限周期光子晶体的透射系数两个方面,对有限和无限周期光子晶体有效折射率的实部和虚部特性曲线分别进行了计算和分析.结果表明一维光子晶体的色散曲线与弹性电偶极子的经典色散曲线类似,在光子晶体的导带为正常色散,而在禁带呈现反常色散.并且用简约布里渊和扩展布里渊区色散曲线对文献报道中存在的两种矛盾的计算结果进行了理论的探讨.解释了导致对一维光子晶体有效折射率计算存在两种不同结果的原因. 相似文献
11.
双芯复合格点光子晶体光纤的负色散特性 总被引:5,自引:1,他引:4
介绍了一种双芯复合格点负色散光子晶体光纤,其包层是由连续电介质纯硅背景上挖出的两种大小不同的空气孔构成,芯区是由掺锗的高折射率的材料构成。为了实现负色散,还移去了包层中的一圈空气孔。采用频域有限差分法对其负色散特性进行分析表明,通过调整空气孔间距和两种空气孔的尺寸,可以得到不同程度的宽带负色散。当内芯半径取0.95μm,孔间距取2.15μm,大空气孔直径取1.9μm,小空气孔直径取1.1μm时,可在1.55μm处实现宽带负色散,其半峰全宽超过了200 nm。这种光纤的包层中空气孔呈六边形分布,空气孔的尺寸均大于1μm,降低了制作的难度。这种光纤可以用于波分复用光纤通信系统中的宽带色散补偿。 相似文献
12.
Dispersion Properties of Photonic Crystal Fiber: Comparison by Scalar and Fully Vectorial Effective Index Methods 总被引:3,自引:0,他引:3
The development of analysis and simulation of propagation characteristics of photonic crystal fiber (PCF) using scalar and fully vectorial effective index methods are described. As a result, we report how the fundamental space filling mode, guided mode and dispersion of the PCF depends on its structural parameters like its normalized air hole spacing, center-to-center spacing of the air holes in the photonic crystal or pitch and radius of the unit cell. Normalized frequency parameter Veff as a function of normalized wavelength for various relative air hole sizes is obtained to estimate the dispersion characteristics of PCF. It is observed that wavelength of zero dispersion, ultraflattened dispersion response and high negative dispersion remarkably differ from two different effective index methods. 相似文献
13.
Recently, an optical attenuator has been important in fiber optic communication systems, because a transmission power in fiber has become higher due to a channel increment in wavelength division multiplexing transmission. A photonic crystal fiber (PCF) optical attenuator is fabricated by air hole diameter reduction in a part of PCF in which radiations are caused in the air hole diameter reduced part of PCF. A PCF optical attenuator has a high power resistance feature due to its radiation-induced operation of optical attenuation. In this paper, we proposed a variable PCF optical attenuator in which a bend was applied to the air hole diameter reduced part in PCF optical attenuator that was fabricated by CO2 laser irradiation. In PCF optical attenuator fabrication, the attenuation was adjusted by the reduced air hole diameter with laser irradiation time control. It was demonstrated that 10.6–13.5 dB of variable attenuation was obtained at 1550 nm-wavelength with 0°–90° bending angle applied to the air hole diameter reduced part in PCF optical attenuator. 相似文献
14.
在光子晶体光纤典型的空气孔三角形排布图案中,将每个空气孔替换为一对孪生空气孔对,孪生空气孔对之间有确定的间距和固定的轴向,并由其形成包层的基本单元.在端面中心位置缺失一孪生空气孔对,由高折射率的背景材料将光场束缚于此形成纤芯.在包层中所有的孪生空气孔对按照三角形规则均匀排列.在这种新型结构中,由于所有孪生空气孔对都具有相同轴向而使得两个正交方向上的折射率不对称,从而导致双折射效应.本文利用有限差分法进行数值计算,所设计孪生空气孔对光子晶体光纤在两个正交方向上的折射率差Δneff可达到10-4.孪生空气孔对结构参量可在一定程度上影响双折射效果,增大空气孔或减小孪生空气孔对内部间距都可在一定程度上增大双折射效应. 相似文献
15.
由于涡旋光具有轨道角动量,将它应用于光纤通信领域可以有效提高信息传输速率.设计了一种环形光子晶体光纤,利用COMSOL Multiphysics软件对其涡旋光TE01,HE±21和TM01模式特性进行模拟计算,它们之间有效折射率差分别为4.59×10~(-4)和3.62×10~(-4);其中,TE01模式的涡旋光在入射光波长范围为1650—1950 nm时,色散值在44.18—45.83 ps·nm~(-1)·km~(-1)之间平坦;入射光波长在1550 nm时,TE01模式的涡旋光的非线性系数为1.37 W~(-1)·km~(-1).该结构的光子晶体光纤的涡旋光具有损耗小、色散平坦等特性,对光纤中传输涡旋光、将涡旋光应用于超连续谱等方面的研究具有重要意义. 相似文献
16.
Dispersion-flattened polarization-maintaining photonic crystal fiber for nonlinear applications 总被引:1,自引:0,他引:1
In this paper, we propose a novel photonic crystal fiber design to achieve high birefringence, high nonlinearity with a flattened dispersion profile. The air holes which are embedded in silica are arranged in triangular lattice configuration. In the core region, an air hole is introduced as the central defect to flatten the dispersion curve. The shape of the defect air hole is deliberately designed elliptical so that high birefringence in the PCF is obtained for polarization-maintaining purpose. The structural parameters are carefully selected to optimize the optical properties. 相似文献
17.
Bhawana Dabas 《Optics Communications》2010,283(7):1331-1337
In this paper, we report a chalcogenide As2Se3 glass photonic crystal fiber (PCF) for dispersion compensating application. We have used the improved fully vectorial effective index method (IFVEIM) for comparing the dispersion properties (negative and zero dispersion) and effective area in hexagonal and square lattice of As2Se3 glass PCF using different wavelength windows. It has been demonstrated that due to their negative dispersion parameter and negative dispersion slope in wavelength range 1.2-2.5 μm, both lattice structures of As2Se3 glass PCFs, with pitch (Λ = 2 μm), can be used as dispersion compensating fibers. Further, design parameters have been obtained to achieve zero dispersion in these fibers. It is also shown that As2Se3 glass PCF provides much higher negative dispersion compared to silica PCF of the same structure, in wavelength range 1.25-1.6 μm and hence such PCF have high potential to be used as a dispersion compensating fiber in optical communication systems. 相似文献
18.
19.
高双折射光子晶体光纤研究 总被引:6,自引:2,他引:4
设计了一种高双折射光子晶体光纤(Photonic Crystal Fiber,PCF),即增大两个与纤芯相邻的空气孔直径,使光纤只具有二重对称性,呈现出较高的双折射.通过压缩x轴方向孔间距,进一步增大双折射度.采用全矢量有限单元法(Finite-element Method,FEM),研究了该光子晶体光纤基模对应的相双折射和群双折射,给出了该高双折射PCF双折射随输入光波长的变化曲线.结果获得了10-3量级的高双折射.具有设计参量的该光子晶体光纤结构的相双折射在1 550 nm处可以达到5.0×10-3,在更长的波长处,这一值会更高. 相似文献