Preparation and electrochemical performance of bramble-like ZnO array as anode materials for lithium-ion batteries

A bramble-like ZnO array with a special three-dimensional (3D) nanostructure was successfully fabricated on Zn foil through a facile two-step hydrothermal process. A possible growth mechanism of the bramble-like ZnO array was proposed. In the first step of hydrothermal process, the crystal nucleus of Zn(OH) ₄ ^2? generated by the zinc atoms and OH^? ions fold together preferentially along the positive polar (0001) to form the needle-like ZnO array. In the second step of hydrothermal process, the crystal nuclei of Zn(OH) ₄ ^2? adjust their posture to keep their c-axes vertical to the perching sites due to the sufficient environmental force and further grow preferentially along the (0001) direction so as to form bramble-like ZnO array. The electrochemical properties of the needle- and bramble-like ZnO arrays as anode materials for lithium-ion batteries were investigated and compared. The results show that the bramble-like ZnO material exhibits much better lithium storage properties than the needle-like ZnO sample. Reasons for the enhanced electrochemical performance of the bramble-like ZnO material were investigated.     

Sn and SnO2-graphene composites as anode materials for lithium-ion batteries

Sn and SnO₂-graphene composites were synthesized using hydrothermal process, followed by annealing in Ar/H₂ atmosphere, and characterized using x-ray diffraction, scanning electron microscopy, and transition electron microscopy. The results indicated that the polycrystalline metallic Sn forms nanospheres with a diameter of 100?～?300 nm, while the SnO₂ nanoparticles are much smaller with a size below 15 nm, which adsorb tightly on the surface of graphene sheets. The Sn and SnO₂-gaphene composites showed good electrochemical performance. After 55 charging/discharging cycles, the capacity remains above 440 mAh/g at a cycling rate of 400 mA/g and the coulombic efficiency is 99.1 %. The good electrochemical properties of the composites are partially contributed to the graphene component with good mechanical flexibility and electrical conductivity, which is an excellent carbon matrix for dispersing the Sn and SnO₂ nanostructures and provides the electron transport pathways as well.     

Tin oxide nano-flower-anchored graphene composites as high-performance anode materials for lithium-ion batteries

The SnO₂ nano-flower/graphene (SnO₂-NF/GN) composites were synthesized by using graphene (GN) and SnO₂ nano-flower (SnO₂-NF). Among them, the SnO₂-NFs were prefabricated by using sodium hydroxide and stannic chloride pentahydrate (SnCl₄·5H₂O) as raw materials. The results of SEM show that the SnO₂-NFs are uniformly dispersed on the surface of GN. Furthermore, compared with the pure SnO₂, the as-prepared SnO₂-NF/GN composites displayed superior cycle performace and high rate capability. The SnO₂-NF/GN composite delivers a specific capacity of 650 mAh g^?1 after 60 cycles and an excellent rate capability of 480 mAh g^?1 at 2000 mA g^?1.     

Synthesis and electrochemical investigation of highly dispersed ZnO nanoparticles as anode material for lithium-ion batteries

Highly dispersed ZnO nanoparticles were prepared by a versatile and scalable sol-gel synthetic technique. High-resolution transmission electronic microscopy (HRTEM) showed that the as-prepared ZnO nanoparticles are spherical in shape and exhibit a uniform particle size distribution with the average size of about 7 nm. Electrochemical properties of the resulting ZnO were evaluated by galvanostatic discharge/charge cycling as anode for lithium-ion battery. A reversible capacity of 1652 mAh g^?1 was delivered at the initial cycle and a capacity of 318 mAh g^?1 was remained after 100 cycles. Furthermore, the system could deliver a reversible capacity of 229 mAh g^?1 even at a high current density of 1.5 C. This outstanding electrochemical performance could be attributed to the nano-sized features of highly dispersed ZnO particles allowing for the better accommodation of large strains caused by particle expansion/shrinkage along with providing shorter diffusion paths for Li⁺ ions upon insertion/deinsertion.     

Effect of pyrolytic polyacrylonitrile on electrochemical performance of Si/graphite composite anode for lithium-ion batteries

The silicon/graphite (Si/G) composite was prepared using pyrolytic polyacrylonitrile (PAN) as carbon precursor, which is a nitrogen-doped carbon that provides efficient pathway for electron transfer. The combination of flake graphite and pyrolytic carbon layer accommodates the large volume expansion of Si during discharge-charge process. The Si/G composite was synthesized via cost-effective liquid solidification followed by carbonization process. The effect of PAN content on electrochemical performance of composites was investigated. The composite containing 40 wt% PAN exhibits a relatively better rate capability and cycle performance than others. It exhibits initial reversible specific capacity of 793.6 mAh g^?1 at a current density of 100 mA g^?1. High capacity of 661 mAh g^?1 can be reached after 50 cycles at current density of 500 mA g^?1.     

Controllable synthesis of spherical silicon and its performance as an anode for lithium-ion batteries

Spherical silicon is controllably synthesized by the hydrolysis of tetraethylorthosilicate (TEOS) with the addition of different contents of ammonia to form SiO₂, then reduced by magnesium powder in argon atmosphere at 900 °C for 3 h. The experimental results show that the electrochemical performance of the as-prepared silicon anode is much affected by the morphology of silicon, and the spherical silicon with a particle size of 250–300 nm shows a reversible capacity of 1,345.8 mAh g^?1 with the capacity retention of 83.2 % after 20 cycles. The relationship between the electrochemical performance of the spherical silicon and the diameters of silicon sphere makes it possible to control the performance of the silicon anode by adjusting the hydrolysis conditions of TEOS.     

Si/polyaniline-based porous carbon composites with an enhanced electrochemical performance as anode materials for Li-ion batteries

Silicon/polyaniline-based porous carbon (Si/PANI-AC) composites have been prepared by a three-step method: coating polyaniline on Si particles using in situ polymerization, carbonizing, and further activating by steam. The morphology and structure of Si/PANI-AC composites have been characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and Raman spectra, respectively. The content and pore structure of the carbon coating layer in Si/PANI-AC have been measured by thermogravimetric analysis and N₂ adsorption-desorption isotherm, respectively. The results indicate some micropores about 1~2 nm in the carbon layer appear during activation and that crystal structure and morphology of Si particles can be retained during preparation. Si/PANI-AC composites exhibit high discharge capacity about 1000 mAh g^?1 at 1.5 A g^?1; moreover, when the current density returns to 0.2 A g^?1, the discharge capacity is still 1692 mAh g^?1 and remains 1453 mAh g^?1 after 70 cycles. The results indicate that the porous carbon coating layer in composites plays an important role in the improvement of the electrochemical performance of pure Si.     

High-rate Li4Ti5O12/C composites as anode for lithium-ion batteries

The Li₄Ti₅O₁₂/C composites were synthesized by a simple solid-state reaction at 800 °C for 12 h by using Super P® conductive carbon black as carbon source. X-ray diffraction analysis shows that the Li₄Ti₅O₁₂ with 0, 5, 7.5, and 10 wt% carbon shows similar patterns with cubic spinel structure. Scanning electron microscope shows that Li₄Ti₅O₁₂ aggregated seriously, but the aggregation was inhibited by the addition of Super P® carbon. The results indicate that the addition of 5 wt% carbon during sintering and a further 5 wt% carbon during slurry preparation shows the best rate capability of 110 mAh/g when the cells were charge/discharged at 10 C rate. The comparison of the charge–discharge curves shows that the higher rate improvement should further decrease the particle size of LTO or improve the conductivity of LTO itself.     

Sn-Sb and Sn-Bi alloys as anode materials for lithium-ion batteries

Sn/SnSb, Sn/Bi, and Sn/SnSb/Bi multi-phase materials were synthesised via reduction of cationic precursors with NaBH₄ and with Zn, and were tested for their suitability as anode materials for Li-ion batteries by galvanostatic cycling. The rapid reduction with NaBH₄ yielded the finer materials with the better cycling stabilities, whereas the reduction with Zn yielded the purer materials with the lower irreversible capacities in the first cycle. Reversible capacities of ∼ 600 mAh g⁻¹, ∼ 350 – 400 mAh g⁻¹, and ∼ 500 mAh g⁻¹ were obtained for Sn/SnSb, Sn/Bi, and Sn/SnSb/Bi, respectively. The cycling stability of the materials decreased in the order Sn/SnSb>Sn/SnSb/Bi>Sn/Bi, which is in part attributed to the presence / absence of intermetallic phases which undergo phase-separation during lithiation. Paper presented at the 8th EuroConference on Ionics, Carvoeiro, Algarve, Portugal, Sept. 16–22, 2001.     

Excellent long-term electrochemical performance of graphite oxide as cathode materials for lithium-ion batteries

A facile, scalable route has been adopted to synthesize graphite oxides with different degrees of oxidation. Subsequently, graphite oxides with rationally designed functional groups have been utilized as cathode materials for lithium-ion batteries (LIBs). The electrodes deliver the initial and second discharge capacities of 332 and 172 mAh g^?1 at a current density of 0.1 A g^?1, respectively. More importantly, a remarkable long-term cycling performance of 130 mAh g^?1 after 800 cycles has been gathered, with an ultralow capacity fading of 0.03% per cycle from the second cycle. The root cause of excellent cycling stability should be ascribed to the admirable reversibility of epoxy and carbonyl groups in graphite oxides during the Li-cycling. Meanwhile, the deep study has provided a novel way to avoid complex and expensive post-treatment process of graphite oxides, whose synthesis conditions are also optimized. Those striking features make graphite oxides as promising cathode materials for lithium-ion batteries.     

Synthesis and electrochemical performance of hole-rich Li4Ti5O12 anode material for lithium-ion secondary batteries

Hole-rich Li₄Ti₅O₁₂ composites are synthesized by spray drying using carbon nanotubes as additives in precursor solution, subsequently followed calcinated at high temperature in air. The structure, morphology, and texture of the as-prepared composites are characterized with XRD, Raman, BET and SEM techniques. The electrochemical properties of the as-prepared composites are investigated systematically by charge/discharge testing, cyclic voltammograms and AC impedance spectroscopy, respectively. In comparison with the pristine Li₄Ti₅O₁₂, the hole-rich Li₄Ti₅O₁₂ induced by carbon nanotubes exhibits superior electrochemical performance, especially at high rates. The obtained excellent electrochemical performances of should be attributed to the hole-rich structure of the materials, which offers more connection-area with the electrolyte, shorter diffusion-path length as well faster migration rate for both Li ions and electrons during the charge/discharge process.     

Novel silicon nanowire film on copper foil as high performance anode for lithium-ion batteries

A novel silicon nanowire film anode was successfully prepared by a combination of magnetron sputtering deposition and metal-catalyzed electroless etching technology. Scanning electron microscopy revealed the formation of a Si film composed of nanowires with a diameter of ~70 nm and lengths of ~3.5 μm. As-prepared Si nanowire film is directly grown on current collectors without binders and carbon additives, which provides a good contact and adhesion of them to current collector. Furthermore, the defined spacing of nanoscale Si nanowire allows Si to undergo large volume change during the alloying/dealloying process without loss of its integrity. These structural features of the resulting Si nanowire make it a promising anode for lithium-ion batteries with remarkably improved electrochemical performance compared with the Si film-based electrode prepared without metal-catalyzed electroless etching process.     

Facile preparation of SGC composite as anode for lithium-ion batteries

The silicon/graphite/carbon (SGC) composite was successfully prepared by ball-milling combined with pyrolysis technology using nanosilicon, graphite, and phenolic resin as raw materials. The structure and morphology of the as-prepared materials are characterized by X–ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscope (TEM). Meanwhile, the electrochemical performance is tested by constant current charge–discharge technique, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) measurements. The electrodes exhibit not only high initial specific capacity at a current density of 100 mA g^?1, but also good capacity retention in the following 50 cycles. The EIS results indicate that the electrodes show low charge transfer impedance R_sf?+?R_ct. The results promote the as-prepared SGC material as a promising anode for commercial use.     

Nanoporous silicon flakes as anode active material for lithium-ion batteries

Nanoporous-silicon (np-Si) flakes were prepared using a combination of an electrochemical etching process and an ultra-sonication treatment and the electrochemical properties were studied as an anode active material for rechargeable lithium-ion batteries (LIBs). This fabrication method is a simple, reproducible, and cost effective way to make high-performance Si-based anode active materials in LIBs. The anode based on np-Si flakes exhibited a higher performances (lower capacity fade rate, stability and excellent rate capability at high C-rate) than the anode based on Si nanowires. The excellent performance of the np-Si flake anode was attributed to the hollowness (nanoporous structure) of the anode active material, which allowed it to accommodate a large volume change during cycling.     

Synthesis and electrochemical characterization of InSn4 and InSn4/C as new anode materials for lithium-ion batteries

The InSn₄ intermetallic powders are synthesized via carbothermal reduction route from In₂O₃ and SnO₂. The reaction possibility is estimated by thermodynamic calculation. Pure InSn₄ intermetallic powders with spherical morphology can be obtained at 900 °C in flowing nitrogen. The micro-sized InSn₄ particle is actually composed of a large number of nano-sized grains with polycrystalline and loose structure. The synthesized InSn₄ shows high reversible specific capacity (ca. 500 mAhg^?1) and a good cycling performance as an anode material for lithium-ion batteries. Coating InSn₄ with carbon can increase the reversible specific capacity and improve significantly the rate capability. The InSn₄/C composite displays a stable specific capacity of ca. 600 mAhg^?1. In consideration of the simple and moderate synthesis route and the mass productive feature, the InSn₄/C composite is a promising anode material for lithium-ion batteries.     

Silicon/carbon nanocomposites used as anode materials for lithium-ion batteries

Silicon/carbon nanocomposites are prepared by dispersing nano-sized silicon in mesophase pitch and a subsequent pyrolysis process. In the nanocomposites, silicon nanoparticles are homogeneously distributed in the carbon networks derived from the mesophase pitch. The silicon/carbon nanocomposite delivers a high reversible capacity of 841 mAh g^?1 at the current density of 100 mA g^?1 at the first cycle, high capacity retention of 98 % over 30 cycles, and good rate performance. The superior electrochemical performance of nanocomposite is attributed to the carbon networks with turbostratic structure, which enhance the conductivity and alleviate the volume change of silicon.     

Silver-coated LiVPO4F composite with improved electrochemical performance as cathode material for lithium-ion batteries

Nano-structured LiVPO₄F/Ag composite cathode material has been successfully synthesized via a sol–gel route. The structural and physical properties, as well as the electrochemical performance of the material are compared with those of the pristine LiVPO₄F. X-ray diffraction (XRD) and scanning electron microscopy (SEM) reveal that Ag particles are uniformly dispersed on the surface of LiVPO₄F without destroying the crystal structure of the bulk material. An analysis of the electrochemical measurements show that the Ag-modified LiVPO₄F material exhibits high discharge capacity, good cycle performance (108.5 mAh g⁻¹ after 50th cycles at 0.1 C, 93% of initial discharge capacity) and excellent rate behavior (81.8 mAh g⁻¹ for initial discharge capacity at 5 C). The electrochemical impedance spectroscopy (EIS) results reveal that the adding of Ag decreases the charge-transfer resistance (R_ct) of LiVPO₄F cathode. This study demonstrates that Ag-coating is a promising way to improve the electrochemical performance of the pristine LiVPO₄F for lithium-ion batteries cathode material.     

Theoretical prediction of borophene monolayer as anode materials for high-performance lithium-ion batteries

Three morphologies of two-dimension Boron with metallicity have been successfully synthetized by experiments. To access the potential of β₁₂ borophene (□) and χ₃ borophene monolayer (◇) as anode materials for lithium ion batteries, first-principles calculations based on density functional theory (DFT) are performed. Lithium atom is preferentially absorbed over the center of the hexagonal B atom hollow of β₁₂ and χ₃ borophene monolayer. The fully lithium storage phase of β₁₂ and χ₃ borophene monolayer corresponds to Li₈B₁₀ and Li₈B₁₆ with a theoretical specific capacity of 1983 and 1240 mA h g^?1, respectively, much larger than other two-dimension materials. Interestingly, lithium ion diffusion on β₁₂ borophene (□) monolayer is extremely fast with a low-energy barrier of 41 meV. Meanwhile, lithiated-borophene monolayer shows enhanced metallic conductivity during the whole lithiation process. Compared to the buckled borophene (△), the extremely enhanced lithium adsorption energy of β₁₂ and χ₃ phase with vacancies weakens lithium ion diffusion. Therefore, it is important to control the generation of vacancy in the buckled borophene (△) anode for lithium ion batteries. Borophene is a promising candidate with high capacity and high rate capability for anode material in lithium ion batteries.     

Carbon-coated Si/graphite composites with combined electrochemical properties for high-energy-density lithium-ion batteries

Carbon-coated Si/graphite composites with different Si/graphite weight ratio have been fabricated using solid-state reaction with aim to improve the cyclic stability, coulombic efficiency, and rate capability simultaneously. Microstructural investigation reveals that the Si particles are covered by amorphous carbon and attached to the carbon-coated graphite surface. Electrochemical evaluation has been performed using cyclic voltammetry and charge/discharge cycling at different current densities, which indicate that addition of graphite can not only enhance the first-cycle coulombic efficiency to 90 % but also improve the cyclic stability drastically. The carbon-coated Si/graphite composite with appropriate contents of Si, graphite, and carbon is expected to be promising candidate as anode materials for high-energy-density lithium-ion batteries.