Ku/K波段双频涡旋电磁阵列天线设计

涡旋电磁波具有携带轨道角动量的特性,利用这一特性,采用涡旋电磁波作为信号的载体,可以实现同一时间、同一频段的多路信号传输,极大地提高系统容量和频带利用率。以同轴馈电的半圆型开槽微带天线为单元,设计出了一种能工作在Ku波段和K波段的涡旋电磁阵列天线。使用三维电磁场仿真软件建模并且优化参数,最终得到在中心频率分别为17.1 GHz和19.7 GHz时,阵列天线产生的电磁波携带有轨道角动量。结论表明:该阵列天线能够产生双频涡旋电磁波。     

Broad band metamaterial absorber based on wheel resonators with lumped elements for microwave energy harvesting

A new metamaterial absorber structure is designed and characterized both numerically and experimentally for microwave energy harvesting applications. The proposed structure includes four wheel resonators with different dimensions, from which the overall response of the structure can then be obtained by summing all the overlapping frequency responses corresponding to each dimension. The essential operation frequency range of the wheels is selected in such a way that the energy used in wireless communications and found within the environment that we live is absorbed. The dimensions are obtained using parametric study and genetic algorithm to realize wideband absorption response. When the simulation and measurement results are taken into account, it is observed that the metamaterial absorber based harvester has potential to absorb and convert microwave energy with an absorption ratio lying within the range of 80 and 99% for the frequency band of 3–5.9 and 7.3–8 GHz. The conversion efficiency of the structure as a harvester is found to be greater than 0.8 in the interval of 2–5 GHz. Furthermore, the incident angle and polarization dependence of the wheel resonator based metamaterial absorber and harvester is also investigated and it is observed that the structure has both polarization and incident angle independent frequency response with good absorption characteristics in the entire working frequency band. Hence, the suggested design having good absorption, polarization and angle independent characteristics with wide bandwidth is a potential candidate for future energy harvester using wireless communication frequency band.     

X波段4单元微带天线阵辐照响应

采用时域有限差分法,并结合导体边缘奇异性处理技术,在不降低计算效率的情况下,保证了计算精度,得到了高功率电磁脉冲辐照下X波段4单元微带天线阵的响应。计算结果表明:馈电点最大响应电压峰值由天线阵各阵元接收的入射脉冲在馈电点叠加引起,且天线阵中主要存在与馈电点激励天线阵不同模式的波。响应电压峰值随着入射脉冲波矢量与正z轴夹角的减小而增大,随着入射脉冲波矢量xOy平面投影与正x轴夹角的增大而增大,频谱随着上述两个夹角的增大均向低频转移。     

一种高增益低雷达散射截面的新型圆极化微带天线设计

设计了一种基于人工电磁材料覆层的高增益低雷达散射截面(radar cross section, RCS)圆极化微带天线. 人工电磁材料覆层是由介质板及其两侧的人工周期表面构成, 上表面是加载集总电阻的方环贴片, 具有宽带吸波特性; 下表面是开条带缝和圆环缝的金属贴片, 具有部分反射特性. 将其加载到圆极化微带天线上方, 通过覆层上表面的电阻可吸收入射的雷达波, 结合下表面与接地板构成Fabry-Perot谐振腔的多次反射, 可实现圆极化微带天线辐射和散射性能的同时改善. 实测结果表明: 加载人工电磁材料覆层后, 天线的相对轴比带宽由5.9%扩展为7.1%; 天线增益在整个工作频带内都得到了提升, 最大提高了6.61 dB; 天线RCS在宽频带宽角域内实现了明显的减缩, 在天线工作频带内也实现了3 dB以上减缩. 实测结果与仿真结果符合较好.     

碳纳米管光学天线的有效波长和谐振特性

将经典金属自由电子气模型应用于金属型碳纳米管, 基于光学天线有效波长理论, 得出了金属型碳纳米管光学天线响应的有效波长与碳纳米管介电特性之间的普适关系. 在对碳纳米管介电特性进行第一性原理计算的基础上, 以金属型4 Å碳纳米管为例, 进一步研究了金属型碳纳米管光学天线响应的有效波长与入射波长之间的关系, 以及金属型碳纳米管光学偶极子天线的谐振特性. 通过将已有传统金属光学天线和碳纳米管天线有效波长的研究结果进行对比, 验证了本文理论的正确性. 结果表明, 碳纳米管光学天线响应的有效波长与入射波长呈近似线性关系, 与传统金属材料构成的同直径光学天线相比, 碳纳米管天线显示出了更强的波长压缩能力, 并且在可见光到红外波段内易于发生谐振. 该研究方法可为碳纳米管光学天线研究提供新的思路.     

S波段微波热致超声成像系统研究

微波热致超声成像技术通过向物体发射微波脉冲, 导致物体吸收电磁波温度迅速升高, 产生瞬时压力波, 从而激发产生超声波信号, 通过传感器对产生的超声波信号进行采集并成像, 最终还原了反映物体吸收电磁波能量特性的图像, 由于此方法兼具了微波成像的高对比性和超声成像的高分辨率特点, 理论上验证了热声成像技术对早期乳腺肿瘤检测的可行性. 本实验兼顾系统成像深度和分辨率, 采用S波段的微波脉冲信号源对物体进行辐射, 利用圆形扫描方式对待测物体进行检测, 同时为了更好的验证成像性能, 本实验同时使用了肿瘤仿体及实际生物组织进行成像实验. 通过实验分析, 验证了该系统对肿瘤仿体和生物组织检测的有效性, 以及系统的高分辨率和高对比度特性, 为早期乳房肿瘤检测提供了进一步的理论支撑.     

基于单层反射超表面的宽带圆极化高增益天线设计

基于Pancharatnam-Berry相位原理, 设计了一种宽带圆极化反射聚焦超表面并将其应用到提高天线增益中. 首先提出了一种变形十字超表面单元, 在11-16 GHz频带范围内能够实现高效同极化转换, 并基于该单元构建了宽带反射聚焦超表面. 仿真结果表明, 垂直入射的右旋圆极化平面波宽带聚焦效果明显. 然后利用单向阿基米德螺旋天线对超表面进行照射, 其辐射的球面波经超表面反射后得到了近平面波, 有效地提高了天线的增益. 最终对所设计的天线系统进行加工并测试, 结果表明系统的-1 dB增益带宽达到25% (12.5-16 GHz), 在该频带范围内峰值增益均高于19 dBc且轴比小于3 dB. 此外, 在12-15.5 GHz范围内天线口径效率均超过50%.     

基于二氧化钒宽、窄带可切换的双功能超材料吸收器研究

本文提出了一种宽、窄带可切换的双功能超材料吸收器.在超材料吸收器的结构中,引入了相变材料二氧化钒(VO2),仅利用单个可切换超表面就能实现不同的功能,其不同功能之间的相互转换通过VO2绝缘态和金属态之间的可逆相变特性实现.当VO2处于金属态时,设计的结构可以看作一个超材料宽带吸收器.仿真结果表明,在1.55THz至2....     

负介电常数材料与负磁导率材料双层结构的透射特性

利用麦克斯韦方程组研究了负介电常数材料和负磁导率材料组成的双层结构的透射特性.电磁波在跨越负介电常数材料层和负磁导率材料层的界面时，由边界条件导致了电磁场的大部分能量局域在界面上，形成特殊的界面模式.研究结果表明，当入射角满足某个特定条件时，这些界面模可以演变为共振隧穿模，导致共振透射的发生.这种输运特性可以实现带通滤波. 关键词： 负介电常数材料 负磁导率材料 单负材料 带通滤波器     

Multiband rectenna for microwave applications

This paper reports a multiband rectenna (rectifier + antenna) suitable for the electromagnetic energy harvesting of the spill-over loss of microwave antennas placed on board of geostationary satellites. Such rectenna is used for powering autonomous wireless sensors for satellite health monitoring. The topology of the rectenna is presented. The experimental results demonstrate that the proposed compact rectenna can harvest efficiently the incident electromagnetic energy at three different frequencies that are close to the resonant frequencies of the cross-dipoles implemented in the antenna array.     

Nanoparticle using parallel split rings and implementation of chain for creating Fano resonance with polarization independence for energy harvesting in mid-infrared

In optical devices, the polarization of the incident wave affects the Nano particle characteristics. Therefore, designing a polarization-independent device is significant in the process of designing optical structures. On the other hand, the concept of Fano resonance and dark mode has been utilized for achieving more energy enhancement. In this paper, we have developed a symmetrical Nano antenna by employing Fano resonance, which is independent of the incident wave polarization. The proposed Nano antenna is modified in mid infrared regime for biosensing and energy harvesting applications. The designed metamaterial antenna is made by Nano split ring resonators with etched capacitive gaps, which are utilized for concentrating energy. The introduced Nano antenna has a bright and dark mode with a weak enhancement of electric field. The effect of the incident wave polarization is investigated at wave incident angles between 0° and 45° to illustrate the independency of the polarization due to the symmetrical shape of the Nano antenna. In order to trigger the dark mode and enhance the electric field, a Nano chain is incorporated in the final structure. This arrangement has led to increasing of electric field drastically. Furthermore, the figure of merit has been calculated as an advantageous factor in sensing the surrounding materials with various refractive indices. Our findings illustrated that the chain arrangement has caused a peak in the linear form of the extinction cross section of the Nano antenna. This in turn has resulted in the appearance of Fano resonance with no impact on the resonance frequency that has been originally adjusted by capacitive gaps and inductive strips.     

Receiving Antenna in a Magnetoplasma in the Resonance Frequency Band

We find the rms voltage on a receiving dipole antenna in the electromagnetic field of a quasipotential-wave packet in a magnetoplasma in the resonance frequency band. It is shown that this voltage can be determined as a product of the electromagnetic-field amplitude of the incident wave by the effective length L_eff of the receiving antenna. For a short dipole whose length is much smaller than the electromagnetic-mode wavelength, the antenna effective length is proportional to the product of the dipole effective length in free space by the excitation coefficient of quasielectrostatic waves (non-normalized electric-field pattern of a dipole). In the case where the receiving antenna is located in proximity to the resonance cone on the lighted side, this excitation coefficient is much greater than unity. Therefore, the determined voltage differs significantly from the conventional estimate which is based on formulas valid for antennas in free space. We perform our derivations using the reciprocity theorem and the fluctuation-dissipation theorem applied to a regular electromagnetic field and a receiving antenna, which constitute the special case of a system which is not in equilibrium but allows an equilibrium (stationary state) to be reached between the incident radiation field and the electromagnetic field reemitted by the antenna. The emphasis is placed on the universal nature of the applied calculation procedure which is valid for arbitrary antennas and matters.     

基于变换光学的椭圆形透明聚集器的设计研究

基于麦克斯韦方程组在不同坐标系下具有形式不变性以及变换光学理论, 通过设计材料的本构参数(介电常数和磁导率)来引导电磁波的传播, 提出了具有电磁透明和电磁聚集两种功能的新型电磁器件-椭圆形透明聚集器的设计方法. 电磁波透明体不会阻挡电磁波的传播并且能够与斗篷内部进行交互; 电磁波聚集器是当电磁波入射到该装置上时, 电磁波能够被设计的装置按照要求集中到一个区域或者一个点, 实现电磁波能量的集中. 本文利用压缩变换和扩展变换推导出了这种电磁器件中各层的相对介电常数和相对磁导率的张量表达式, 并利用基于有限元算法的电磁仿真软件对该电磁器件进行了全波仿真验证, 得到了入射波从各个不同方向入射时磁场z 分量的分布图, 仿真结果证实了该设计方法和电磁参数的正确性. 最后还讨论了电磁器件存在损耗时的情况, 当损耗逐渐增大时, 器件的功能在一定程度上受到了削弱. 本文的设计方法为其他新型电磁器件的设计提供了一种新的思路.     

柱形等离子体辐射场和阻抗的数值计算

由柱形非磁化等离子体色散关系，得到信号沿柱形等离子体传输波矢空间分布，再根据天线方程推导得到柱形等离子体在轴向密度均匀、不均匀情况下辐射方向图、辐射阻抗与增益等参数.理论计算结果与实验都证明了柱形等离子体辐射方向图随等离子体参数变化而改变，同时实验结果表明，重新得到的数值计算结果更加精确，更加符合实际测量结果，这对等离子体作为天线传输具有重要的参考价值. 关键词： 柱形等离子体 辐射阻抗 辐射方向图     

采用Helmholtz共鸣器与悬臂梁压电换能器的声能采集器研究

针对环境中广泛存在的声能,提出了一种采用Helmholtz共鸣器和悬臂梁压电换能器的声能采集器。Helmholtz共鸣器对入射声压进行放大,放大后的声压引起共鸣器弹性薄壁振动,薄壁的振动传递到压电换能器产生电能输出。建立了带弹性壁的立方形共鸣器的等效集中参数理论模型,并与压电换能器的机电特性结合,分析了声能采集器的声-机-电转换原理,研究了声压、声波频率和负载阻抗对输出功率的影响,研究结果为此类声能采集器的优化设计及工程应用提供了一种可行的方法。实验中,声源通过声波导管输出声能,当共鸣器管口处的声压级为94 dB时,系统实测最大输出功率达240μW。该采集器不仅可作为声能自供能采集器,还可在较远距离为低能耗电子装置进行有源声供能。      

多功能太赫兹超表面偏振控制器

本文提出了一种“金属栅-开口环/硅环-金属栅”结构的透射式超表面偏振控制器, 研究了入射角度和抽运光对该器件传输及偏振态控制性能的影响. 研究结果表明, 当线偏振太赫兹波垂直入射时, 可对0.39-1.11 THz频段的太赫兹波实现偏振方向90°旋转, 偏振旋转效率为99%, 损耗为1 dB. 对于斜入射的情况, 偏振转换性能在0-60°范围内基本保持不变, 且透过率达到90%以上. 同时, 通过调控抽运光强度的方式, 该器件能够实现对透射与反射太赫兹光束的强度调制, 调制深度均达到90%, 且可以实现太赫兹波偏振分束功能. 该器件可以作为未来太赫兹空间光通信和信息处理的宽带、角度不敏感、可调谐的偏振转换器和分束器.     

�ǴŻ�����������������ĵ�Ų�ɢ�����Է���

The characteristic of electromagnetic scattering by plasma cylinder is researched in this paper. Scattered fields of the parallel-polarized wave and vertical-polarized wave by plasma cylinder are calculated and analyzed. The calculated results show that the higher the electron density, is the greater the scattering intensity in the outside of the cylinder and the higher the plasma frequency of collision, is the smaller the scattering intensity in the outside of the column. In addition, the electromagnetic wave polarization and frequency of the incident wave also have a significant impact on the scattering intensity of electromagnetic waves, the vertically polarized wave is more likely to be scattered, and the lower frequency of the incident wave is also easier to scattering. These have certain reference value for designing and studying of the plasma antenna.     

基于FPGA的电磁脉冲电场测量系统

为了测量纳秒级前沿的电磁脉冲电场,研制了一种基于现场可编程门阵列(FPGA)的宽频带电磁脉冲电场测量系统,该系统采用单极子天线作为电场探头的接收天线,高速AD采集调理电路输出的电压信号,由FPGA接收AD采样的数据并保存至DDR2和FLASH存储器中;分析了系统的整体方案;对系统的信号调理、采集的触发方式、FPGA控制以及干扰屏蔽等关键技术进行了重点分析;通过电场探头、电磁脉冲模拟器、PTEM暗室、衰减器以及示波器进行了性能和功能验证实验;利用软件将电场探头和示波器测得的信号进行处理和对比;实验表明,所研制的电场探头可以测量前沿大于2.5ns、电场强度为0~50kV/m的脉冲电场,系统线性度好,体积小,抗干扰性能好,测量准确性高。     

MNZ超材料的电磁特性

主要围绕磁导率接近0的MNZ超材料,通过理论分析和数值模拟方法对MNZ材料的电磁特性进行了研究。针对线源置于二维MNZ材料内部的情况,通过理论详细分析了在MNZ材料和空气交界处的阻抗匹配特性和传播常数的连续性,基于有限元数值方法模拟验证了电磁场在MNZ材料边界处的等幅同相特性,从而实现了均匀平面波的传播特性。同时,考虑到将线源置于空气中有助于辐射出电磁能量,通过数值模拟分析了电磁波由空气入射到MNZ材料的电磁特性,发现在特定极化条件下,只能当电磁波波前与MNZ材料边界平行时,才能较好地实现阻抗匹配,从而基于MNZ材料实现新颖的辐射特性。     

Coherent backscattering of electromagnetic waves in a magnetised plasma

Summary A microwave coherent backscattering experiment has been carried out on Mirabelle, a weakly ionised plasma device, with the objective of measuring the electron density fluctuation level. The experiment is a preliminary step in order to prepare the detection system for a microwave stimulated backscattering experiment. The incident electromagnetic wave is focused in front of a plane grid which excites ion acoustic or electron Bernstein waves inducing fluctuations in the plasma. The backscattering signal is collected by the launching circuit and detected by homodyne mixing. The typical ratio of the scattered power to the incident power is about 10⁻¹² and the relative density fluctuations are of the order of δn _e/n _e=10⁻³ against a background electron density ofn _e=1–5·10⁹ cm⁻³. The backscattering measurement is compared with Langmuir probe measurements. The spectral width of the backscattered signal has also been studied, by taking into account effects due to the incident wave focusing and plasma wave damping. The authors of this paper have agreed to not receive the proofs for correction