以C70衍生物为电子受体的高效聚合物固体薄膜太阳能电池

以PC[70]BM(phenyl C71-butyric acid methyl ester)取代PC[60]BM(phenyl C61-butyric acid methyl ester)作为电子受体材料,以MEH-PPV(poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene])为电子给体材料,制成了本体异质结(bulk heterojunction,BHJ)聚合物太阳能电池.MEH-PPV/PC[70]BM器件在AM1.5G(80 mW/cm2)模拟太阳光的光照条件下得到了3.42%的能量转换效率,短路电流值达到了6.07 mA/cm2,开路电压0.85 V,填充因子为53%.通过紫外可见吸收光谱和外量子效率的研究,发现PC[70]BM作为电子受体,对扩大光谱的吸收范围和增加活性层的吸收系数有明显的作用.同时比较了不同溶剂对该体系器件性能的影响.通过原子力显微镜(AFM)、光暗导I-V曲线等研究,分析了1,2-二氯苯有利于给体相和受体相的微相分离和载流子的传输的原因.     

Large open-circuit voltage polymer solar cells by poly(3-hexylthiophene) with multi-adducts fullerenes

Polymer solar cells (PSCs) made by poly(3-hexylthiophene) (P3HT) with multi-adducts fullerenes, [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM), PC61BM-bisadduct (bisPC61BM) and PC61BM-trisadduct (trisPC61BM), were reported. Electrochemistry studies indicated that PC61BM, bisPC61BM and trisPC61BM had step-up distributional lowest unoccupied molecular orbital (LUMO) energy. PSCs made by P3HT with above PC61BMs show a trend of enlarged open-circuit voltages, which is in good agreement with the energy difference between the LUMO of PC61BMs and the HOMO of P3HT. On the contrary, reduced short-circuit currents (Jsc) were observed. The investigation of photo responsibility, dynamics analysis based on photo-induced absorption of composite films, P3HT:PC61BMs and n-channel thin film field-effect transistors of PC61BMs suggested that the short polaron lifetimes and low carrier mobilities were response for reduced Jsc. All these results demonstrated that it was important to develop an electron acceptor which has both high carrier mobility, and good compatibility with the electron donor conjugated polymer for approaching high performance PSCs.     

Development of a new benzo(1,2-b:4,5-b')dithiophene-based copolymer with conjugated dithienylbenzothiadiazole-vinylene side chains for efficient solar cells

A new benzodithiophene-based copolymer PTG1 with dithienylbenzothiadiazole-vinylene side chains exhibits excellent film-forming ability, a deep HOMO energy level, and a good miscibility with PC(71)BM. Bulk heterojunction polymer solar cells fabricated from PTG1 and PC(71)BM showed a promising power conversion efficiency over 4.0%.     

A Supramolecular Complex in Small-Molecule Solar Cells based on Contorted Aromatic Molecules

"Ball and socket" motif: The contorted dibenzotetrathienocoronene (6-DBTTC) forms a complex with the C(70) fullerene PC(70) BM embedded in an amorphous phase of PC(70) BM. The materials are processable into organic solar cells in solution. The power conversion efficiency is maximal when there is a 1:2 molar ratio of 6-DBTTC to PC(70) BM. Formation of the supramolecular complex directly affects charge separation in the active layer.     

Phase diagram of P3HT:PC70BM thin films based on variable-temperature spectroscopic ellipsometry

In this article, we present the research on the influence of the composition of thin films of a blend of poly (3-hexylthiophene −2,5-diyl) - P3HT with fullerene derivatives [6,6]-phenyl-C71-butyric acid methyl ester – PC70BM and [6,6]-phenyl-C61-butyric acid methyl ester – PC60BM on their thermal transitions. The influence of molar mass (Mw) of P3HT (Mw = 65.2; 54.2 and 34.1 kDa) and PCBM (PC60BM – Mw = 911 g/mol and PC70BM – Mw = 1031 g/mol) is examined in details. The article presents significantly expanded research compared to our previous work on thermal transitions in thin films of blend P3HT (Mw = 65.2 kDa) with PC60BM. For this reason, we also compare current results with previous ones. Here, we present for the first time a phase diagram of thin films of the P3HT(Mw = 65.2 kDa):PC70BM blend using variable-temperature ellipsometry. Our research reveals the presence of characteristic temperatures of pure phases in thin films of P3HT: PCBM blends. It turns out that the cold crystallization temperature of the P3HT phase in P3HT(Mw = 65.2 kDa):PC70BM blend films is lower than corresponding temperature in P3HT(Mw = 65.2 kDa):PC60BM blend films. At the same time, the cold crystallization temperature of the PC70BM phase behaves inversely. We demonstrate also that variable-temperature spectroscopic ellipsometry is a very sensitive technique for studying thermal transitions in these thin films. In addition, we show that the entire phase diagram can be determined based on the raw ellipsometric data analysis, e.g. using a delta angle at wavelength λ = 280 nm.     

Fullerenes and derivatives as electron transport materials in perovskite solar cells

In this study, two fullerenes (C60, C70) and their methano-substitutions (PC61BM, PC71BM), as electron transport materials (ETMs) in perovskite solar cells (Pero-SCs), were systematically studied. As being used as ETMs, methanofullerenes, though with lower electron mobility compared to the counterpart pristine fullerenes, lead to higher power conversion efficiencies (PCEs) of Pero-SCs. The difference is likely caused by the fill-out vacancies and smoother morphology of the interfaces between ETM and perovskite layers, as they were prepared by different methods. In addition, compared to C60 and PC61BM, C70 and PC71BM showed priority in terms of short-circuit current density, which should be attributed to fast free charge extraction abilities.     

Tetrathienoanthracene-based copolymers for efficient solar cells

A series of semiconducting copolymers (PTAT-x) containing extended π-conjugated tetrathienoanthracene units have been synthesized. It was shown that the extended conjugation system enhanced the π-π stacking in the polymer/PC(61)BM blend films and facilitated the charge transport in heterojunction solar cell devices. After structural fine-tuning, the polymer with bulky 2-butyloctyl side chains (PTAT-3) exhibited a PCE of 5.6% when it was blended with PC(61)BM.     

Fullerene derivative acceptors for high performance polymer solar cells

Polymer solar cells (PSCs) are composed of a blend film of a conjugated polymer donor and a soluble fullerene derivative acceptor sandwiched between a PEDOT?:?PSS coated ITO positive electrode and a low workfunction metal negative electrode. The conjugated polymer donor and the fullerene derivative acceptor are the key photovoltaic materials for high performance PSCs. For the acceptors, although [6,6]-phenyl-C(61)-butyric acid methyl ester (PC(60)BM) and its corresponding C(70) derivative PC(70)BM are dominantly used as the acceptors in PSC at present, several series of new fullerene derivatives with higher-lying LUMO energy level and better solubility were reported in recent years for further improving the power conversion efficiency of the PSCs. In this perspective paper, we reviewed the recent research progress on the new fullerene derivative acceptors, including various PC(60)BM-like C(60) derivatives, PC(60)BM bisadduct, PC(70)BM bisadduct, indene-C(60) bisadduct and indene-C(70) bisadduct, trimetallic nitride endohedral fullerenes and other C(60) derivatives with multi side chains. The synthesis and physicochemical properties of PC(60)BM and PC(70)BM were also introduced considering the importance of the two fullerene acceptors.     

J-aggregation induced low bandgap anthracene-based conjugated molecule for solution-processed solar cells

A new anthracene-based X-shaped conjugated molecule, HBTATHT, was synthesized. Thin film transistors based on unannealed HBTATHT showed a carrier mobility of 0.15 cm(2) V(-1) s(-1) (I(on/off) = 7.9 × 10(6)). Further, a solution processed solar cell made of HBTATHT exhibited promising power conversion efficiencies of 4.84% and 4.70% with PC(61)BM (1?:?0.8 wt ratio) and PC(71)BM (1?:?0.6 wt ratio), respectively.     

聚合物:富勒烯薄膜光伏电池的反常高温热稳定性研究

聚合物太阳能电池光电转换效率已接近商业化要求,但稳定性差却成为其实用化瓶颈因素.高温暴晒是聚合物太阳能电池实用化必须面临的环境,因此提高聚合物太阳能电池的热稳定性至关重要.本文以典型的Poly(3-hexylthiophene-2,5-diyl(P3HT):[6,6]-Phenyl-C61-butyric acid methyl ester(PC61BM)基聚合物太阳能电池为研究模型,考察其在不同加热温度下(50~110℃)持续工作时的器件效率变化行为,结果发现电池在高温下表现出一种非常规的性能衰减再回升的行为,具体表现为高温下电池首先表现指数式急速衰减(20%~25%),随后发生反常的性能快速恢复至接近初始效率,之后电池保持超长的高温稳定性.光学显微镜和激光光束诱导电流成像结果证明,顶电极覆盖可以有效抑制活性层中PC61BM的聚集结晶,因而电池的反常热诱导稳定性提升与PC61BM的大量聚集结晶无关.活性层薄膜的紫外可见吸收光谱和器件外量子效率的表征结果证明,持续高温加热没有促进PC61BM二聚体的形成,反而有利于PC61BM二聚体的解离.综合实验分析结果,推测PC61BM在光照下的快速二聚反应及其高温解离是导致电池表现出反常热稳定性提升行为的主要原因.实验结果揭示了初期制备的聚合物太阳能电池实际处于一种亚稳态,对器件进行短暂的前期热退火有利于稳定活性层结构,消除亚稳态,有效提升器件稳定性.本研究工作不仅对富勒烯基聚合物太阳能电池的热诱导反常稳定性提升机理机制给出了解释,而且提供了一种提高聚合物太阳能电池稳定性的新策略.     

Facile synthesis of a 56π-electron 1,2-dihydromethano-[60]PCBM and its application for thermally stable polymer solar cells

A facile synthesis was employed to make a 56π-electron methano-PC(61)BM with a very small 1,2-dihydromethano (CH(2)) group. This new fullerene derivative possesses high electron mobility (0.014 cm(2) V(-1) s(-1)) and higher LUMO energy level (0.15 eV) than PC(61)BM. Bulk hetero-junction devices based on using poly(3-hexylthiophene) and methano-PC(61)BM as active layer exhibited better performance and thermal stability than those using the PC(61)BM analogue.     

低聚合度的交替共聚物太阳能电池的形态和性能

制备了由低聚合度的聚[2,6-(4,4-双-(2-乙基己基)-4H-环戊[2,1-b;3,4-b']双噻吩)-交替-4,7-(2,1,3-苯并噻二唑)](LDP-PCPDTBT)、[6,6]-苯基-C61-丁酸甲酯(PC61BM)和聚甲基丙烯酸甲酯(PMMA)组成的三组分共混薄膜,并通过加入溶剂添加剂(1,8-二溴辛烷,DBO)对体系进行了优化处理.研究发现,没有加入DBO时,LDP-PCPDTBT和PC61BM相在PMMA的基质中分别是无定形的和结晶的;加入DBO后,PMMA基质中LDP-PCPDTBT和PC61BM间的相分离过程得到优化,有机太阳能电池的能量转换效率相应提高了32.4%.     

Effects of additives on the morphology of solution phase aggregates formed by active layer components of high-efficiency organic solar cells

Processing additives are used in organic photovoltaic systems to optimize the active layer film morphology. However, the actual mechanism is not well understood. Using X-ray scattering techniques, we analyze the effects of an additive diiodooctane (DIO) on the aggregation of a high-efficiency donor polymer PTB7 and an acceptor molecule PC(71)BM under solar cell processing conditions. We conclude that DIO selectively dissolves PC(71)BM aggregates, allowing their intercalation into PTB7 domains, thereby optimizing both the domain size and the PTB7-PC(71)BM interface.     

Charge trapping and storage by composite P3HT/PC60BM nanoparticles investigated by fluorescence-voltage/single particle spectroscopy

Fluorescence-voltage/single particle spectroscopy (F-V/SPS) was employed to study exciton-hole polaron interactions and interfacial charge transfer processes for pure poly(3-hexylthiophene) (P3HT) nanoparticles (NPs) and composite P3HT/PC(60)BM NPs in functioning hole-injection devices. F-V/SPS data collected on a particle-by-particle basis reveal an apparent bistability in the fluorescence-voltage modulation curves for composite NPs of P3HT and [6,6]-phenyl-C(61)-butyric acid methyl ester (PC(60)BM) that is absent for pure P3HT NPs. A pronounced deep trapping of free electrons photogenerated from the composite P3HT/PC(60)BM NPs at the NP/dielectric interface and hole trapping by fullerene anions in composite P3HT/PC(60)BM NPs under photoexcitation lies at the basis of this finding. The deep electron trapping effect reported here for composite conjugated polymer/fullerene NPs presents an opportunity for future application of these NPs in nanoscale memory and imaging devices.     

6,7-dialkoxy-2,3-diphenylquinoxaline based conjugated polymers for solar cells with high open-circuit voltage

6,7-Dialkoxy-2,3-diphenylquinoxaline based narrow band gap conjugated polymers, poly[2,7-(9-octyl-9H-carbazole)-alt-5,5-(5,8-di-2-thinenyl-(6,7-dialkoxy-2,3-diphenylquinoxaline))] (PCDTQ) and poly[2,7-(9,9-dioctylfluorene)-alt-5,5-(5,8-di-2-thinenyl-(6,7-dialkoxy-2,3-diphenylquinoxaline))] (PFDTQ), have been synthesized by Suzuki polycondensation. Their optical, electrochemical, transport and photovoltaic properties have been investigated in detail. Hole mobilities of PCDTQ and PFDTQ films spin coated from 1,2-dichlorobenzene (DCB) solutions are 1.0 × 10-4 and 4.1 × 10-4 cm2V-1s-1, respectively. Polymer solar cells were fabricated with the as-synthesized polymers as the donor and PC61BM and PC71BM as the acceptor. Devices based on PCDTQ:PC71BM (1:3) and PFDTQ:PC71BM (1:3) fabricated from DCB solutions demonstrated a power conversion efficiency (PCE) of 2.5% with a Voc of 0.95 V and a PCE of 2.5% with a Voc of 0.98 V, respectively, indicating they are promising donor materials.     

窄带系聚合物APFO3的激发态光物理特性

化学计算证实了光致激发窄带系聚合物APFO3后,会发生链内电荷转移（ICT）过程,同时这一特性还影响了吸收光谱中的第一吸收带. 瞬态吸收结果再一次表明了当聚合物在单分散体系中确实存在ICT特性,而且这种特性会同振动弛豫竞争. 在聚集态中,受链间相互作用的影响,ICT特性会消失,而且激子弛豫过程将在光致激发后的弛豫过程中占据主导地位. 混有PC61BM的APFO3薄膜的光致激发动力学显示,当PC61BM 的含量超过50%时,激子解离已经达到饱和. 基于此异质节的光伏器件性能显示PC61BM的含量高于50％以后,光电流的增幅也很小．     

High performance low band gap polymer solar cells with a non-conventional acceptor

A novel C70 fullerene derivative was designed and synthesized by [4+2] cyclic addition reaction between indene derivative (methyl 1H-indene-3-carboxylate) and C70. The absorption and photoluminescence of H120 and its mixed films with different polymer donor materials were investigated, as well as its electrochemical property and electron mobility. It was found that H120 has 0.05 eV higher LUMO level than that of PC(70)BM. Its electron mobility reached 6.32 × 10(-4) cm(2) V(-1) s(-1), which is slightly lower than 9.55 × 10(-4) cm(2) V(-1) s(-1) of PC(70)BM. The photovoltaic devices based on P3HT, and two high efficiency low band gap polymers, PBDTTT-C and PBDTTDPP as donors, with H120 as an acceptor gave power conversion efficiencies of 4.2%, 6.0% and 6.2%, respectively.     

Crystalline low band-gap alternating indolocarbazole and benzothiadiazole-cored oligothiophene copolymer for organic solar cell applications

A low band-gap alternating copolymer of indolocarbazole and benzothiadiazole-cored oligothiophene demonstrated balanced crystallinity and solubility; a solar cell combining this polymer with PC(61)BM in a preliminary test demonstrated power conversion efficiencies of 3.6%.     

A naphthodithiophene-diketopyrrolopyrrole donor molecule for efficient solution-processed solar cells

We report the synthesis, characterization, and first implementation of a naphtho[2,3-b:6,7-b']dithiophene (NDT)-based donor molecule in highly efficient organic photovoltaics (OPVs). When NDT(TDPP)(2) (TDPP = thiophene-capped diketopyrrolopyrrole) is combined with the electron acceptor PC(61)BM, a power conversion efficiency (PCE) of 4.06 ± 0.06% is achieved-a record for a PC(61)BM-based small-molecule OPV. The substantial PCE is attributed to the broad, high oscillator strength visible absorption, the ordered molecular packing, and an exceptional hole mobility of NDT(TDPP)(2).     

Naphthodithiophene-2,1,3-benzothiadiazole copolymers for bulk heterojunction solar cells

Two newly synthesized naphthodithiophene-based copolymers, PNB, exhibit a low optical bandgap of ～1.64 eV with which the solar cells fabricated from the blend of PNB and PC(71)BM afforded a power conversion efficiency of 5.3% with external quantum efficiency over 60% in a broad spectral range.