Morphology-dependent luminescence behavior of Y<Subscript>2-x</Subscript>Gd<Subscript>x</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> thin-film phosphors grown by a laser ablation

Y_2-xGd_xO₃:Eu³⁺ luminescent thin films have been grown on Al₂O₃(0001) substrates using pulsed laser deposition. Films grown under different deposition conditions have been characterized using microstructural and luminescence measurements. The crystallinity, surface morphology and photoluminescence (PL) of the films are highly dependent on the amount of Gd present. The photoluminescence (PL) brightness data obtained from Y_2-xGd_xO₃:Eu³⁺ films grown under optimized conditions have indicated that Al₂O₃(0001) is one of the most promising substrates for the growth of high-quality Y_2-xGd_xO₃:Eu³⁺ thin-film red phosphors. In particular, the incorporation of Gd into the Y₂O₃ lattice could induce a remarkable increase of PL. The highest emission intensity was observed with Y_1.35Gd_0.60Eu_0.05O₃, whose brightness was increased by a factor of 3.1 in comparison with that of Y₂O₃:Eu³⁺ films. This phosphor may be promising for application in flat-panel displays. PACS 78.20.-e; 78.55.-m; 78.66.-w     

Non-critical phase-matched second harmonic generation in Gd<Subscript>x</Subscript>Y<Subscript>1-x</Subscript>COB

We have characterized non-critical phase-matching (NCPM) for both Type I and Type II second harmonic generation (SHG) in y-cut Gd_xY_1-xCOB using a nanosecond optical parametric oscillator (OPO). The variation of the NCPM wavelength with temperature was investigated for different values of the compositional parameter x. Efficient SHG of 1064 nm was achieved by choosing the suitable compositional parameter x=0.28 and by tuning the temperature of the crystal to 52 °C. Using a 25-mm-long Gd_0.28Y_0.72COB crystal, conversion efficiencies of 41 and 43% were obtained respectively from a mode-locked Nd:YAG and a Q-switched Nd:YAG laser. PACS 42.25.Lc; 42.65.Ky; 42.70.Mp; 42.79.Nv     

Quantum cutting in Gd<Subscript>2</Subscript>SiO<Subscript>5</Subscript>: Eu<Superscript>3+</Superscript> by VUV excitation

The emission and excitation spectra of Gd₂SiO₅∶Eu³⁺ were investigated using the VUV beam line of the Beijing Synchrotron Radiation Facility (BSRF). The experimental results were discussed in the frame of visible quantum cutting process involved in Gd³⁺−Eu³⁺ system. Upon direct excitation into the⁶G _J states of Gd³⁺, two visible photon emissions from Eu³⁺ were observed. Cursory evaluation proved that Gd₂SiO₅∶Eu³⁺ is an efficient visible quantum cutter.     

Possibility of adjusting photoluminescence spectra of Ca scheelites (CaMoO<Subscript>4</Subscript>: Eu<Superscript>3+</Superscript> and CaWO<Subscript>4</Subscript>: Eu<Superscript>3+</Superscript>) to the emission spectrum of incandescent lamps

The peculiarities of the photoluminescence of compounds CaMoO₄: Eu³⁺ and CaWO₄: Eu³⁺ with the scheelite structure associated with a change in the short- and long-range orders of the crystal lattice upon a change in the activator (Eu³⁺) of the photoluminescence range in the interval 1–4 mol %, in which the photoluminescence of the matrix is preserved in the range 484–557 nm, are investigated using X-ray phase analysis as well as photoluminescence, Raman, and diffuse reflection spectroscopies. The introduction of Eu³⁺ ions leads to the reconstruction of the lattice so that up to 10% of these ions stimulate the formation of centrosymmetric localization upon the substitution of Ca²⁺ ions in the noncentrosymmetric positions. It is found that the spectral radiant emittance of the more effective luminophore CaMoO₄: Eu³⁺ can be adjusted to this parameter for an incandescent lamp for the Eu³⁺ concentration of 1–2 mol %.     

Performance comparisons of passively Q-switched intracavity-frequency-doubled Nd:Gd<Subscript>0.19</Subscript>Y<Subscript>0.81</Subscript>VO<Subscript>4</Subscript> and Nd:Gd<Subscript>0.83</Subscript>Y<Subscript>0.17</Subscript>VO<Subscript>4</Subscript> lasers at 671 nm

Performance comparisons of laser-diode pumped passively Q-switched intracavity-frequency-doubled Nd:Gd_0.19Y_0.81VO₄ and Nd:Gd_0.83Y_0.17VO₄ lasers at 671 nm are demonstrated for the first time to our knowledge. KTP crystal is used as the frequency doubling material and V:YAG crystal as the saturable absorber with initial transmission of 89%. The dependences of average output power, pulse width, pulse repetition rate, single-pulse energy and peak power on incident pump power are measured and contrasted. The experimental results show that, Nd:Gd_0.83Y_0.17VO₄ laser has more excellent properties than Nd:Gd_0.19Y_0.81VO₄ laser at 671 nm.     

Photolumiscent Properties of Nanorods and Nanoplates Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript>

Nanorods and nanoplates of Y₂O₃:Eu³⁺ powders were synthesized through the thermal decomposition of the Y(OH)₃ precursors using a microwave-hydrothermal method in a very short reaction time. These powders were analyzed by X-ray diffraction, field emission scanning electron microscopy, Fourrier transform Raman, as well as photoluminescence measurements. Based on these results, these materials presented nanoplates and nanorods morphologies. The broad emission band between 300 and 440 nm ascribed to the photoluminescence of Y₂O₃ matrix shifts as the procedure used in the microwave-hydrothermal assisted method changes in the Y₂O₃:Eu³⁺ samples. The presence of Eu³⁺ and the hydrothermal treatment time are responsible for the band shifts in Y₂O₃:Eu³⁺ powders, since in the pure Y₂O₃ matrix this behavior was not observed. Y₂O₃:Eu³⁺ powders also show the characteristic Eu³⁺ emission lines at 580, 591, 610, 651 and 695 nm, when excited at 393 nm. The most intense band at 610 nm is responsible for the Eu³⁺ red emission in these materials, and the Eu³⁺ lifetime for this transition presented a slight increase as the time used in the microwave-hydrothermal assisted method increases.     

Correlation of photoluminescence of (La,Ln) PO<Subscript>4</Subscript>:Eu<Superscript>3+</Superscript> (Ln = Gd and Y) phosphors with their crystal structures

Eu³⁺-doped (La, Ln) PO₄ (Ln = Gd and Y) phosphors were prepared by a facile co-precipitation method. Their structures and luminescent properties under UV excitation were investigated. Structural characterization of the nanostructured luminescence material was carried out with X-ray powder diffraction analysis. Scanning electron microscopy was carried out to understand the surface morphological features and grain sizes with 50–100 nm. It is found that (La, Gd) PO₄:Eu³⁺ phosphors have the same crystal structure as LaPO₄:Eu³⁺, which is monoclinic with a little different lattice parameters. In the case of (La, Y) PO₄:Eu³⁺ phosphors, however, the gradual change from monoclinic to tetragonal structure of host lattice was observed, as the amount of Y ion increased. From the photoluminescence spectra for (La, Ln) PO₄:Eu³⁺ (Ln = Gd and Y), the emission transition ⁵D₀ → ⁷F₁ has been found to be more prominent over the normal red emission transition ⁵D₀ → ⁷F₂. Furthermore, the size influence on the products was discussed. It was observed that the spectral features possess sharp and bright emission for potential applications on the monitors of the television and some other related electronic systems, in observing the images in orange–red color.     

Correction of the band gap of Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> phosphor

Submicron samples of Y₂O₃:Eu³⁺ phosphor with elevated photoluminescence (PL) efficiency and activator concentration of 9 at % obtained by the sol–gel method were investigated by diffuse reflection spectroscopy and PL spectroscopy. It is found that the diffuse reflection spectrum in the vicinity of the fundamental absorption edge (<300 nm) is distorted by the superposition of the PL of Eu³⁺ ions, as a result of which the calculated value of optical band gap E _g of the Y₂O₃ matrix is overestimated. An algorithm for eliminating the PL influence on the absorption edge is proposed, and the correct E _g values are found to be 4.61 ± 0.12 and 4.50 ± 0.12 eV for annealing at 700 and 1300°C, respectively.     

Luminescence thermometry using Gd<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript>

In this paper we study the possibility of using the synthesized nanopowder samples of Gd₂Zr₂O₇:Eu³⁺ for temperature measurements by analyzing the temperature effects on its photoluminescence. The nanopowder was prepared by solution combustion synthesis method. The photoluminescence spectra used for analysis of Gd₂Zr₂O₇:Eu³⁺ nano phosphor optical emission temperature dependence were acquired using continuous laser diode excitation at 405 nm. The temperature dependencies of line emission intensities of transitions from ⁵D₀ and ⁵D₁ energy levels to the ground state were analyzed. Based on this analysis we use the two lines intensity ratio method for temperature sensing. Our results show that the synthesized material can be efficiently used as thermographic phosphor up to 650 K.     

Spontaneous luminescence of Eu<Superscript>3+</Superscript> ions in porous Y<Subscript>2</Subscript>O<Subscript>3</Subscript> nanospheres

A study of the luminescence of Eu³⁺ ions in Y₂O₃ nanospheres indicates a significant influence of the porous structure of nanoparticles on the luminescence of dopant ions. It is shown that filling the nanopores of initially porous Y₂O₃ nanospheres shortens the decay time of the spontaneous luminescence of doping europium ions. The change in the decay time is associated with the change in the effective refractive index of the porous nanospheres.     

The synthesis of (Y<Subscript>1-x</Subscript>Gd<Subscript>x</Subscript>)<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu phosphor particles by flame spray pyrolysis with LiCl flux

(Y_1-xGd_x)₂O₃:Eu phosphor particles with dense morphology were prepared by flame spray pyrolysis and the effect of LiCl flux on the crystallinity, morphology, and photoluminescence characteristics of the particles was investigated. All as-prepared particles had monoclinic phase regardless of flux and had different luminescence characteristics from those of commercial Y₂O₃:Eu particles of cubic phase. The addition of LiCl flux reduced the post-treatment temperature by 300 °C for phase transformation from the monoclinic phase to the cubic phase. The post-treatment temperature of (Y_0.75Gd_0.25)₂O₃:Eu particles for phase transformation decreased from 1100 °C to 700 °C when LiCl flux was used. The morphology of the particles was also influenced by the Y/Gd ratio and the LiCl flux. The as-prepared particles had spherical shape and non-aggregation characteristics regardless of Y/Gd ratio and flux. The sphericity of the as-prepared particles prepared without flux was maintained after post-treatment for phase transformation in all Y/Gd ratios. However, LiCl addition promoted the aggregation between product particles. The prepared particles had high photoluminescence intensities comparable to that of the commercial product. PACS 64.70.Kb; 78.55.-m; 81.20.Rg; 75.50.Tt     

Local structure of Gd<Superscript>3+</Superscript> and Eu<Superscript>2+</Superscript> impurity centers in a CdF<Subscript>2</Subscript> crystal

The local crystal structure of Gd³⁺ and Eu²⁺ cubic impurity centers in cadmium fluoride is calculated within the shell model in the pair potential approximation. The local compressibility of the cationic and anionic sublattices of the host lattice is determined in the vicinity of the Gd³⁺ (Eu²⁺) impurity ion.     

Tunable emission and efficient energy-transfer properties of Ce<Superscript>3+</Superscript> and Mn<Superscript>2+</Superscript> co-doped Ba<Subscript>3</Subscript>Gd(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> phosphors

MgO powders subjected to Q-switched laser pulses in water were characterized by X-ray/electron diffraction and optical spectroscopy to have a significant optical property change with accompanied transformation into the phase assemblages of periclase, brucite and liquid-crystalline lamella. The periclase nanoparticles tended to have {111} habit planes parallel to the basal layers of lamella and brucite flakes more or less rolled as fibers, ribbons or tubes. A significant internal compressive stress was built up for periclase and brucite but not the more flexible lamellar phase. The colloidal suspension containing the densified periclase nanoparticles within the rolled brucite/lamellae flakes showed UV–visible absorption corresponding to a minimum band gap of ca. 5 eV.     

A high efficient antireflective down-conversion Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Bi<Superscript>3+</Superscript>, Yb<Superscript>3+</Superscript> thin films

The high efficient antireflective down-conversion Y₂O₃:Bi, Yb films have been prepared successfully on Si(100) substrates by pulsed laser deposition (PLD) method, Upon excitation of ultraviolet photon varying from 300 to 400 nm, near-infrared emission of Yb³⁺ was observed for the film, can be efficiently absorbed by silicon (Si) solar cell. Most interestingly, there is a very low average reflectivity 1.46% for the incident light from 300 to 1100 nm. To the best of our knowledge, this is the lowest reflectance for the down-conversion thin films prepared by cost efficient method. The surface topography of the high efficient antireflective films can be controllably tuned through the substrate template regulation by optimizing process parameters. Besides, the results showed that there is a close relationship between luminescent property and morphology of the film. With the change of the surface morphology, the intensity of Bi³⁺ and Yb³⁺ emission peaks increase first and then decrease. The obtained results demonstrate that this film can enhance the Si solar cell efficiency through light trapping and spectrum shifting.     

All-solid-state Nd:Gd<Subscript>0.18</Subscript>Y<Subscript>0.82</Subscript>VO<Subscript>4</Subscript>-LBO green laser at 532 nm

We report a continuous-wave (CW) coherent green radiation at 532 nm by intracavity frequency doubling generation of 1064 nm Nd:Gd_0.18Y_0.82VO₄ laser. With incident pump power of 18.2 W, output power of 1.08 W at 532 nm has been obtained using a 5 mm-long KTP crystal. The optical conversion efficiency was up to 5.9%. At the output power level of 1.08 W, the output stability is better than 5%. The beam quality M² values were equal to 1.26 and 1.12 in X and Y directions, respectively.     

Red,Yellow, Blue and Green Emission from Eu<Superscript>3+</Superscript>, Dy<Superscript>3+</Superscript> and Bi<Superscript>3+</Superscript> Doped Y<Subscript>2</Subscript>O<Subscript>3</Subscript>nano-Phosphors

Rare earth elements (RE = Eu³⁺& Dy³⁺)and Bi³⁺ doped Y₂O₃ nanoparticles were synthesized by urea hydrolysis method in ethylene glycol, which acts as reaction medium as well as a capping agent, at a low temperature of 140 °C,followed by calcination of the obtained product. Transmission electron microscope (TEM) images reveals that ovoid shaped Y₂O₃ nanoparticles of around 22–24 nm size range were obtained in this method. The respective RE and Bi³⁺ doped Y₂O₃ precursor nanoparticles when heated at 600 and 750 °C, retains the same shape as that of the as-synthesized Y₂O₃ precursor samples. From EDAX spectra, the incorporation of RE ions into the host has been studied. XRD pattern reveals the crystalline nature of the heated nanoparticles and indicate the absence of any impurity phase other than cubic Y₂O₃.However, the as-synthesized nanoparticles were highly amorphous without the presence of any sharp XRD peaks. Photoluminescence study suggests that the synthesized samples could be used as red (Eu³⁺), yellow (Dy³⁺), blue and green (Bi³⁺)emitting phosphors.     

luminescence of BaGa<Subscript>2</Subscript>Se<Subscript>4</Subscript> crystals activated by Eu<Superscript>2+</Superscript> and Ce<Superscript>3+</Superscript> ions

We have studied the effect of doping with Eu²⁺ and Ce³⁺ ions on the photoluminescence (PL) of BaGa₂Se₄ crystals in the temperature range 77–300 K. We have established that the broad bands with maxima at wavelengths 456 nm and 506 nm observed in the photoluminescence spectra of BaGa₂Se₄:Ce³⁺ crystals are due to intracenter transitions 5d → ²F_7/2 and 5d →²F_5/2 of the Ce³⁺ ions, while the broad photoluminescence band with maximum at 521 nm in the spectrum of BaGa₂Se₄:Eu²⁺ is associated with 4f⁶ 5d → 4f⁷ (⁸S_7/2) transitions of the Eu²⁺ ion. We show that in BaGa₂Se₄:Eu²⁺,Ce³⁺ crystals, excitation energy is transferred from the Ce³⁺ ions to the Eu²⁺ ions.     

On the Luminescence of Ce<Superscript>3+</Superscript>, Eu<Superscript>3+</Superscript>, and Tb<Superscript>3+</Superscript> in Novel Borate LiSr<Subscript>4</Subscript>(BO<Subscript>3</Subscript>)<Subscript>3</Subscript>

This paper reports on the photoluminescence (PL) and time-resolved properties of Ce³⁺, Eu³⁺, and Tb³⁺ in novel LiSr₄(BO₃)₃ powder phosphors. Ce³⁺ shows an emission band peaking at 420 nm under 350-nm UV excitation. Energy transfer from Ce³⁺ to Mn²⁺ takes place in the co-doped samples. Eu³⁺ shows red emission under near UV excitation. LiSr₄(BO₃)₃:Eu³⁺ phosphor could be a suitable candidate for phosphor-converted solid state lighting. The luminescence lifetime is 2.13 ms for Eu³⁺ in LiSr₄(BO₃)₃:0.001Eu³⁺. As Eu³⁺ concentration increasing, the decay curves deviate from exponential behavior. Tb³⁺ shows the strongest ⁵D₄→⁷ F₅ emission line at 540 nm. Decay curves of ⁵D₄→⁷ F₅ and ⁵D₃→⁷ F₅ emission with different Tb³⁺ concentrations were also measured. Cross-relaxation process is discussed based on the decay curves.     

Enhanced photoluminescence of Ca<Subscript>2</Subscript>Al<Subscript>2</Subscript>SiO<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript> by charge compensation method

The effect of compensator on optical properties of Ca₂Al₂SiO₇:Eu³⁺ is systematically investigated by the X-ray powder diffraction, photo-luminescence (PL) properties and lifetime. It is obviously observed that the PL intensity of Eu³⁺ under 394 nm excitation increases in the order of Ca_1.86Eu_0.14Al₂SiO₇ (CAS), Ca_1.72Na_0.14Eu_0.14Al₂SiO₇ (CASNa) and Ca_1.86Eu_0.14Al_2.14Si_0.86O₇ (CASAl), the intensity of Eu³⁺ are 100%, 134%, 184%, and the lifetime of Eu³⁺ are 0.75 ms, 1.28 ms and 1.39 ms, respectively. A charge compensation model is proposed to explain the changes in the emission intensity and lifetime of Eu³⁺ in Ca₂Al₂SiO₇ with different compensation methods. PACS 78.55.-m; 61.72.Ji; 61.43.Gt; 42.70.-a; 74.62.Dh