花形ZnO纳米片微球的合成、表征及光催化性能

以ZnCl2和尿素为原料,采用水热法合成了由纳米片组成的花形微球碱式碳酸锌前驱体,然后在300℃下煅烧0.5 h得到了形貌一致的ZnO产物。采用XRD、FTIR、TG、SEM、TEM、XPS对其进行表征,结果表明产物为六方纤维矿结构ZnO;组成3D花型微球的纳米片构筑单元厚度为10 nm,表面呈孔装结构,比表面积为72 m2.g-1。分别以花形ZnO纳米片、单分散ZnO纳米片和商用ZnO纳米颗粒为光催化剂,通过降解罗丹明B(Rh B)进行了光催化活性研究。结果表明,与商用ZnO纳米颗粒相比,水热法制备的花形ZnO纳米片显示了更好的光催化活性,可能是由于花形ZnO纳米片微球有较高的比表面积和3D花形形貌所致。     

球形和花形ZnO纳米结构的可控制备及其光催化机理

报道了一种简单的制备球形和花形ZnO纳米结构的无模板水热法。在Zn(NO_3)_2·6H_2O与NH_3·H_2O的体系中,通过改变乙二醇和水的体积比,140℃水热反应2 h分别制备出球形和花形ZnO纳米结构。采用SEM、XRD、UV-Vis DRS和PL对其进行了表征和分析,结果表明球形ZnO纳米结构的直径为500 nm~1μm,它是由纳米颗粒自组装而成;花形ZnO纳米结构是由长度为300~700 nm,直径为100~300 nm的纳米棒组装而成。研究了乙二醇在球形和花形ZnO纳米结构形成过程中的作用并提出了可能的生长机理。室温下分别以球形和花形ZnO纳米结构为光催化剂,以偶氮染料甲基橙MO作为光催化研究对象,紫外光照2 h,对MO的降解率分别为83%和55%。以叔丁醇(t-Butanol)、乙二胺四乙酸二钠(EDTA-2Na)为自由基和空穴的捕获剂,推测其催化机理主要为空穴氧化和自由基协同氧化历程。     

功能性CdSe纳米晶的合成及自组装膜光致发光

以巯基丙酸(RSH)为稳定剂,采用湿化学法合成了功能性CdSe纳米晶,用XRD、TEM表征其粒度和形貌,用UV-Vis监测成核及成膜过程。结果表明：制得的CdSe近似呈球形,平均粒径为48 nm。利用静电自组装法层层组装成CdSe-PDDA复合膜,荧光测试表明：所得CdSe纳米晶自组装复合膜(CdSe-PDDA)的荧光强度随着组装层数的增加而呈线性增强,该复合膜在582 nm附近有黄绿色荧光发射。     

壳聚糖-CdS复合膜制备及其对吡啶的传感特性

利用壳聚糖（CS）易于成膜的特点，模拟生物矿化，在有机物调制下通过异相成核生长制备了CS/CdS纳米颗粒复合膜.研究了成膜条件对膜的水热稳定性和发光性能的影响，以及CS/CdS纳米颗粒复合膜对水体中吡啶的响应特性.扫描电镜分析表明CS/CdS纳米颗粒复合膜均匀性好， CdS以物理掺杂方式均匀分布于CS薄膜中， CdS颗粒尺寸在70 nm左右.但薄膜荧光光谱位置和形状表明实际发光的CdS簇集体直径小于20 nm.由此推测电镜观察到的CdS颗粒可能是由许多CdS小颗粒聚集而成，小颗粒之间因有机物的存在而相互隔离. CS/CdS纳米颗粒复合膜的荧光发射对水体中吡啶的存在十分敏感，微量吡啶的存在会引起薄膜荧光发射急剧增强.除铜和碘离子外，水体系中其他常见离子对薄膜荧光发射没有显著影响，预期CS/CdS纳米颗粒复合薄膜有可能发展成为一种重要的水体系吡啶测定专用传感薄膜材料.     

CdS@g-C3N4复合核壳纳米微粒的制备与光催化性能

采用水热法,在乙二胺和EDTA-2Na作用下,成功制备了CdS@g-C3N4复合核壳纳米微粒,并探讨了其生长机理。结果显示:CdS@g-C3N4复合核壳纳米微粒的比表面积是纯CdS纳米颗粒的14.0倍,具有良好的光催化活性和光稳定性。当反应条件为180℃、4 h、CdS/g-C3N4质量比1.9∶1时,CdS@g-C3N4的可见光催化性能最好,300 W氙灯光照2 h,RhB的降解率达95.2%,明显高于纯CdS。重复使用3次后,CdS@g-C3N4形貌、结构及光催化性能无明显变化。     

在SDS-PVP团簇软模板中自组装多脚状金纳米粒子

利用十二烷基硫酸钠(SDS)与聚乙烯吡咯烷酮(PVP)组成的团簇为软模板, 在微波辅助下以柠檬酸钠为还原剂快速还原氯金酸生成金晶并自组装成多脚状金纳米粒子. TEM结果显示, 得到回转直径约为50 nm的多脚状纳米结构, 电子衍射(ED)证实其为多晶结构. XRD结果表明, 该多脚状金纳米结构主要沿(111)晶面生长, 构成该纳米结构的晶粒尺寸约为12.7 nm. SDS与PVP组成的团簇结构对金纳米粒子的形貌有显著影响, 固定PVP浓度时, 随着SDS浓度增大, 金纳米粒子的形貌由球形向多脚状转变, 同时还原产物水溶液的UV-Vis光谱在800 nm附近的吸收逐渐增强.     

利用牛血清蛋白合成CdS纳米棒和网状纳米线

采用简单易控、对环境友好的矿化方法, 利用牛血清蛋白(BSA)做模板, 通过Cd2+与硫代乙酰胺(TAA)反应制备了形貌均一的CdS纳米棒和网状纳米线. 分别采用透射电子显微镜(TEM)、X射线能谱(EDS)、X射线衍射(XRD)、荧光(PL)发射谱和导电原子力显微镜(C-AFM)等方法对不同实验温度下制备的CdS样品的结构形貌、成分组成和光学性质及微区电子传输行为进行了表征. 结果表明: 在实验反应温度为20 ℃时, 得到的产物为单分散性好的CdS 纳米棒, 长度为250 nm, 直径为30 nm; 在50 ℃时, 得到网状CdS纳米线, 其长度为2-3 μm; CdS纳米棒和网状纳米线均为立方相闪锌矿结构. 荧光性质的测试表明, CdS纳米棒和网状纳米线具有优良的荧光性能, 电流-电压(I-V)特性的表征表明CdS纳米线具有很好的电导特性.     

γ射线辐照法制备CdS纳米棒及性能表征

在pH=3的酸性条件下,以硫酸镉和硫代乙酰胺(TAA)为反应前驱体,采用十六烷基三甲基溴化铵(CTAB)自组装形成的管状胶束(PVAC)为模板,通过γ射线辐照法成功合成了CdS纳米棒,并通过XRD、UV-Vis、SAED、TEM和PL等技术对反应中间产物及最终产物进行了表征。研究表明,该方法在Cd²⁺浓度为0.015 mol·L^-1、辐照剂量为15～20 kGy时,可获得直径在100 nm以下,长度在3 μm以上的CdS纳米棒;并且较低的辐照剂量和反应物浓度有利于获得较大长径比的CdS纳米棒。     

水热合成CdS纳米晶体的形貌控制研究

研究了水热合成CdS纳米晶体形貌的化学控制，选择不同的络合试剂为模板,研究其对水热合成CdS纳米晶体形貌的影响.实验发现若以络合试剂乙二胺、甲胺为模板时，产品CdS晶体的形貌分别为（20～30） nm×（200～600） nm和（40～50） nm×（200～600） nm尺寸的纳米棒;而以络合试剂吡啶、 氨为模板时，产品CdS晶体的形貌分别为平均尺寸约30 nm和20 nm的纳米颗粒.用XRD、TEM、XPS、PL和Raman光谱等技术对所得CdS纳米棒进行了表征.同时对水热合成CdS纳米晶体形貌的模板控制机制进行了探讨，提出了一种水热合成CdS纳米棒的络合物结构诱导生长机理.     

以SDS-PEG团簇为软模板在温和条件下合成金纳米环

介绍一种由十二烷基硫酸钠(SDS)与聚乙二醇(PEG 20000)组成的团簇为软模板, 在室温、常压、无硬模板及无外加还原剂条件下自还原HAuCl₄合成金纳米环的新方法. TEM显示合成的金纳米环的直径为(500±50) nm; UV-vis光谱显示在800 nm以上区域有强吸收带, 证明有大的各向异性的纳米结构生成. 电子衍射(ED)显示合成的金纳米环为金单晶结构; XRD显示金纳米环的(200)与(111)衍射峰的强度比(I₍₂₀₀₎/I₍₁₁₁₎)为0.11, 比反应初始阶段的0.31降低0.2左右, 表明金纳米结构主要为(111)晶面取向. TEM和SEM跟踪显示, 金纳米环的生长经历了从金纳米球到纳米片再到纳米环的变化过程, 控制反应时间可以得到预期的金纳米结构.     

Synthesis and characterization of flowerlike ZnO nanostructures via an ethylenediamine-meditated solution route

Flowerlike ZnO nanostructures were deposited on Si substrate by choosing hexamethylenetetramine as the nucleation control reagent and ethylenediamine as the chelating and capping reagent. Structural and optical measurements reveal that obtained ZnO exhibits well-defined flowerlike morphology, hexagonal wurtzite structure, uniform distribution on substrate, and strong photoluminescence in ultraviolet band. The well-arrayed pedals of each ZnO flower possess the typical tapering feature, and are built up by many well-aligned ZnO nanorods. Moreover, each single nanorod building up the pedal exhibits the single crystal nature and the growth direction along c-axis. Effects of the precursor composition on the morphology of ZnO were discussed.     

片状碘化铋辅助液相法合成硫化镉纳米线的取向行为和场发射特性

利用低温液相法可控合成有序硫化镉纳米结构. 用片状碘化铋作为可分解的二维模板实现硫化镉纳米线的生长调控. 采用不同尺寸的片状碘化铋并控制反应温度, 成功制备出硫化镉纳米线的平面方形网状结构、无序交织网状结构和有序阵列结构. 电子显微分析、X射线衍射和光致发光分析显示, 这些纳米结构晶化程度良好. 场发射测试表明, 硫化镉纳米线由横向排列向竖直排列的可控变化使得硫化镉纳米线平面方形网状结构、无序交织网状结构和有序阵列结构的场发射性能依次增强.     

Hierarchical Nitrogen‐Doped Flowerlike ZnO Nanostructure and Its Multifunctional Environmental Applications

Hierarchical nitrogen‐doped ZnO flowerlike nanostructures were synthesized on a large scale. These nanostructures were characterized by FESEM, HRTEM, XRD, FTIR, XPS, and TGA, and their suitability for multifunctional environmental applications was investigated. The experimental results demonstrated that the hierarchical N‐doped ZnO flowerlike nanostructure enhances the photodegradation of methyl blue (MB) and acid orange 7 (AO7) by presenting a large specific surface area and high light utilization rate, inhibits the growth of bacteria without light irradiation, and increases the permeate flux when used in a membrane filtration system. These advantages of the hierarchical N‐doped ZnO flowerlike nanostructure brings benefits to the environmental application fields.     

Shape-controlled synthesis of 3D and 1D structures of CdS in a binary solution with L-cysteine's assistance

A facile L-cysteine-assisted route was designed for the selectively controlled synthesis of 1D and novel, interesting 3D CdS spherical nanostructures constructed from CdS nanorods (or nanopolypods) in a binary solution. By controlling reaction conditions such as the molar ratio between Cd(OAc)2 and L-cysteine and the volume ratio of the mixed solvents, the synthesis of various 3D architectural structures and 1D wirelike structures in large quantities can be controlled. This is the first reported case of the direct growth of novel 3D self-assemblies of CdS nanorods (or nanopolypods). The morphology, structure, and phase composition of the as-prepared CdS products were examined by using various techniques (X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), selected-area electron diffraction (SAED), high-resolution TEM, and Raman spectroscopy). On the basis of the results from TEM studies and our analysis, we speculate that in the present synthesis the L-cysteine dominates nucleation growth and the ethylenediamine (en)-dominated, oriented-assembly process. Interestingly, the products obtained show a gradient evolution in color from light-yellow to dark-yellow, which implies that their intrinsic optical properties change, possibly due to variations in their special morphologies and structures. This facile solution-phase L-cysteine-assisted method could be extended for the controlled preparation of other metal chalcogenides nanostructures with complex morphologies.     

片状碘化铋铺助液相法合成硫化镉纳米线的取向行为和场发射特性

利用低温液相法可控合成有序硫化镉纳米结构.用片状碘化铋作为可分解的二维模板实现硫化镉纳米线的生长调控.采用不同尺寸的片状碘化铋并控制反应温度,成功制备出硫化镉纳米线的平面方形网状结构、无序交织网状结构和有序阵列结构.电子显微分析、X射线衍射和光致发光分析显示,这些纳米结构晶化程度良好.场发射测试表明,硫化镉纳米线由横向排列向竖直排列的可控变化使得硫化镉纳米线平面方形网状结构、无序交织网状结构和有序阵列结构的场发射性能依次增强.     

Electromagnetic functionalized cage-like polyaniline composite nanostructures

Novel cage-like and electromagnetic functional polyaniline (PANI)/CoFe2O4 composite nanostructures, in which the self-assembled PANI nanofibers (approximately 15 nm in diameter) entwined around the octahedral CoFe2O4 magnet acting as the nucleation site or template, were successfully prepared by FeCl3 as either oxidant and dopant via a self-assembly process. The coordination effect of the magnet as a nucleation site or template and the magnetic interaction between the PANI nanofibers and CoFe2O4 as a driving force results in such cage-like nanostructures. The cage-like composite nanostructures not only have high conductivity (sigmamax approximately 5.2 S/cm), but also show a typical ferromagnetic behavior.     

Facile hydrothermal synthesis of 3D hierarchical Bi2SiO5 nanoflowers and their luminescent properties

Facile hydrothermal synthesis of novel hierarchical flowerlike Bi₂SiO₅ nanostructures consisting of single-crystal nanosheets is reported using polyvinylpyrrolidone (PVP, K30) as capping reagent in the presence of NaOH. The obtained products are systematically characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and Fourier transform infrared spectroscopy. Control experiments are carried out to investigate various factors that affect the morphology and size of the products. The results indicate that the nucleation and growth of the flowerlike nanostructures are dominated by a nucleation–dissolution–recrystallization growth mechanism. It is demonstrated that the concentrations of PVP and NaOH play important roles in the formation of the hierarchical nanoflowers. Moreover, the room-temperature photoluminescence properties of the Bi₂SiO₅ nanoflowers are also investigated.     

Self-assembly of flowerlike AlOOH boehmite 3D nanoarchitectures

In this work, a hydrothermal route using an ethanol-water solution to progressively synthesize a sequence of flowerlike three-dimensional gamma-AlOOH boehmite nanostructures without employing templates or matrixes for self-assembly is presented. The flowerlike boehmite nanoarchitectures exhibit three hierarchies of self-organization, i.e., single-crystalline nanorods, nanostrips, and bundles, which are characterized by scanning and transmission electron microscopy. The sequence of products obtained after different processing times indicates a self-assembly mechanism. The hydrogen bonding on the surface of nanorods or nanostrips possibly plays a key role, as identified by FTIR spectra of the products after they had been heated to 1000 degrees C. The specific surface area and pore-size distribution of the obtained product as determined by gas-sorption measurements show that the boehmite nanoarchitectures exhibit high BET surface area and porosity properties.     

溶剂热法合成CdS纳米晶及其光学性质研究

以硫脲和醋酸镉为原料,采用溶剂热法在不同的反应介质和温度下合成了CdS纳米晶,比较了单胺与双胺对合成CdS纳米晶形貌的影响。采用透射电镜(TEM)、X射线粉末衍射仪(XRD)和荧光分光光度计(PL)对合成的CdS纳米晶结构和光学性能进行表征。结果表明:反应温度和反应介质对其形貌有影响,在双胺的条件下,60℃时合成了纯相的六方相CdS纳米棒;双胺条件下更易生成纳米棒,且高温下晶体的结晶性更好。PL分析表明,水(溶剂)热法制备的CdS的荧光光谱图与大多数CdS类似,均在440~480 nm和550 nm处存在发射峰,但较宽的发射峰蓝移说明材料的光学性质受到材料形貌和制备方法的影响。