不锈钢辐射损伤随温度和剂量的变化(英文)

用重离子辐照模拟和正电子湮没寿命技术研究了改进型316L不锈钢在21 和33 dpa辐照剂量下的辐照损伤在室温到802 °C温度范围随辐照温度变化和室温下0—100 dpa剂量范围随辐照剂量变化. 在580 °C左右实验观察到辐照肿胀峰， 在21 和33 dpa辐照剂量下相应的空位团分别由14和19个空位组成， 尺度分别为0.68 和0.82 nm. 空位团尺寸随辐照剂量增加， 在100 dpa时空位团由8个空位组成， 尺度为0.55 nm. 实验结果表明， 在改进型316L不锈钢中辐照损伤随辐照温度变化更灵敏.     

钨辐射损伤随辐照剂量变化的重离子辐照模拟研究

采用重离子辐照模拟方法和正电子湮没寿命测量技术研究了钨辐射损伤随辐照剂量的变化。20,60和90dpa（每个原子的位移次数）辐照损伤水平的实验结果表明,辐照在钨中产生单空位、双空位、位错和空位团等缺陷;随辐照剂量的增大,单空位、双空位和位错浓度增加,空位团的尺度和浓度都随之增大。Radiation damage in W has been studied as a function of irradiation dose by heavy ion simulation and positron annihilation lifetime measurement. The experimental results of 20, 60 and 90 dpa irradiations illustrate that the mono-and di-vacancies, dislocations and vacancy clusters are produced by the irradiation. The concentrations of the mono-and di-vacancies and dislocations and both the concentration and size of the vacancy clusters or voids all increase with the increasing of the irradiation dose.     

质子辐照铝膜反射镜的慢正电子湮没研究

采用分光光度计测定了60keV质子辐照后铝膜反射镜反射光谱的变化规律.用慢正电子湮没等分析技术研究了辐照损伤的微观机制.结果表明，当质子辐照主要作用于反射镜铝膜层中时反射镜在200—800nm波长范围内反射率随辐照剂量增加而下降.入射质子可对铝膜中的缺陷产生填充作用，减小铝膜中电子密度，增加弱束缚电子带间跃迁.紫外至可见光能量较高的波段可引起带间激发跃迁，使相应的谱段反射率下降，导致反射镜光学性能的退化. 关键词： 反射镜 光学性能 质子辐照 慢正电子湮没     

质子辐照空间级硅橡胶的正电子淹没寿命谱研究

用正电子淹没寿命谱方法（PALS）研究了质子辐照对空间级硅橡胶KH-L-Y微观结构的影响。试验结果表明,PALS谱所揭示的最长寿命成分的t3, I3及自由体积分数Vf随辐照剂量的增加开始明显下降;而当辐照剂量大于1015cm-2后,随剂量的增加平缓上升。辐照剂量小于1015cm-2时,质子辐照使硅橡胶自由体积减小,分子链间堆砌紧密;辐照剂量大于1015cm-2时,质子辐照使硅橡胶自由体积增大。交联密度及DMA测试结果同样表明,质子辐照在剂量较小时硅橡胶的交联密度及玻璃化转变温度增加,辐照以交联效应为主;而剂量较大时辐照降解占优势。     

质子辐照空间级硅橡胶的正电子淹没寿命谱研究

 用正电子淹没寿命谱方法（PALS）研究了质子辐照对空间级硅橡胶KH-L-Y微观结构的影响。试验结果表明，PALS谱所揭示的最长寿命成分的t₃, I₃及自由体积分数Vf随辐照剂量的增加开始明显下降；而当辐照剂量大于10¹⁵cm^-2后，随剂量的增加平缓上升。辐照剂量小于10¹⁵cm^-2时，质子辐照使硅橡胶自由体积减小，分子链间堆砌紧密；辐照剂量大于10¹⁵cm^-2时，质子辐照使硅橡胶自由体积增大。交联密度及DMA测试结果同样表明，质子辐照在剂量较小时硅橡胶的交联密度及玻璃化转变温度增加，辐照以交联效应为主；而剂量较大时辐照降解占优势。     

BaF_2晶体质子辐射效应研究

通过对BaF2 晶体进行质子辐照实验 ,研究BaF2 晶体质子辐照后的荧光发射谱及正电子湮没寿命谱。初步探讨BaF2 晶体经质子辐照后出现的现象和机理。     

PdAgHx金属氢化物正电子湮没研究

在77—295 K温区和氢浓度0—0.35范围采用正电子湮没寿命测量方法研究了Pd0.75Ag0.25H_x氢化物合金. 充氢后正电子湮没寿命谱可以用两个寿命成分表征. 短寿命成分τ1不随温度和氢浓度变化, 是自由正电子湮没寿命; 长寿命成分τ2及其相对强度I2不随温度变化, 但随氢浓度的增加分别增大和减小, τ2是氢气泡捕获的正电子湮没寿命, τ2增大和I2减小说明随氢浓度增大氢聚集成的气泡的尺度增大, 而浓度减小. 实验结果表明, 氢脆的微观机理是氢气泡致脆. The metal hydride PdAgHx with a hydrogen concentration x ranging from 0 to 0.35 has been investigated by positron annihilation lifetime method in the temperature region between 77 K and 295 K. The measured lifetime spectra in metal hydride PdAgHx are characterized by two lifetimes τ1 and τ2. The short lifetime τ1 is independent of both hydrogen concentration and temperature, which is ascribed to the annihilation lifetime of free positrons. The long lifetime τ2 and its intensity I2 do not change with temperature, while τ2 increases and I2 decreases with increasing of hydrogen concentration. τ2 is attributed to the lifetime of positrons trapped at the hydrogen bubble. The increase of τ2 indicates the growth of the hydrogen bubble, and the decrease of I2 shows the reduction of the hydrogen bubble concentration. The experimental result shows a microscopic mechanism that the hydrogen bubble produced causes hydrogen embrittlement.     

正电子湮没谱和光致发光谱研究掺锌GaSb质子辐照缺陷

用正电子湮没谱和光致发光谱研究了质子辐照后掺锌GaSb中的缺陷.通过分析正电子的缺陷寿命τ₂及强度I₂的变化发现,在高能质子的辐照下产生了双空位缺陷V_GaV_Sb,可能同时产生了小的空位团.正电子平均寿命τ_av和S参数随着质子辐照剂量的变化也证明了这一结论.通过分析不同质子辐照剂量下掺锌GaS     

CMOS图像传感器在质子辐照下热像素的产生和变化规律

应用于空间的图像传感器在辐射影响下产生的热像素严重影响空间光电探测性能,本文通过质子辐照试验研究了热像素的产生和变化规律。首先,使用3 MeV和10 MeV两种能量的质子对图像传感器进行辐照,分析不同能量、不同注量的质子辐照产生热像素的性质;其次,再对辐照后的器件进行退火试验,分析热像素的退火规律。对于相同注量辐照,3 MeV质子辐照下热像素产生率大约是10 MeV质子辐照下的2.3倍,但是10 MeV质子辐照产生热像素的灰度值高于3 MeV质子;辐照过程中热像素的数量都是随着注量的增加线性增加。退火过程中,热像素数量都不断减少,而3 MeV质子辐照产生的热像素相比于10 MeV质子,退火更为显著。结果表明,质子辐照下每个质子与器件之间的作用过程及产生缺陷的机制是相对独立的,不同质子的作用过程之间没有相关性。不同能量的质子辐照产生缺陷的类型不同,导致热像素具有不同特性。     

质子辐照对永磁合金微观结构演化的研究

钐钴和钕铁硼稀土永磁合金已经广泛应用于粒子加速器的波荡器和其他器件中,作为加速器的重要组成部分,永磁合金在辐照环境中长期服役会出现磁性能损失的现象,这会影响束流的品质.为了探讨产生这个现象的微观机理,采用透射电镜对质子辐照前后的钐钴和钕铁硼稀土永磁合金进行了微观结构演化的表征和分析,统计了由辐照析出的纳米晶体积密度和粒径分布,并讨论了微观结构演化对宏观磁性能损失的影响.结果表明,随着质子辐照损伤程度的增加,永磁合金的微观结构从单晶结构转变为纳米晶多晶结构,且纳米晶和基体的晶体结构相同.钕铁硼的纳米晶体积密度先增大后减小,粒径分布先增大后不变;钐钴的纳米晶体积密度逐渐减小,粒径逐渐增大.在2 dpa的质子辐照损伤程度下,钕铁硼稀土永磁合金比钐钴永磁合金的非晶化趋势更明显.     

充氚不锈钢中氦行为的实验研究

对充氚和未充氚的抗氢-2不锈钢(HR-2)样品进行退火处理,利用正电子湮没寿命谱技术以及金相检验技术探讨不锈钢中氦和微缺陷的相互作用行为.未充氚样品中,影响正电子寿命值的主要因素为杂质元素在晶界的析出.充氚样品实验中,退火温度小于300℃时,正电子寿命值的增加说明了氦泡的形成过程为非热形成,通过“冲出位错环”机制形成及长大;退火温度在300~600℃之间,充氚样品正电子寿命值的降低以及He的跃迁概率的计算结果,说明He原子通过热迁移至晶界;退火温度大于600℃时,热平衡空位浓度的计算结果以及正电子寿命值的增加说明热平衡空位开始发挥作用.     

85MeV19 F重离子辐照α-Al2O3的空洞研究

5.28×1016cm-2 85MeV 19 F辐照的α-Al2O3中,在其热退火过程中采用正电子湮没方法首次观察到了空洞. 450℃退火开始产生空洞,550℃到750℃空洞半径约为0.29nm不随温度变化,但浓度随温度增加而增加;高于750℃,空洞半径随温度升高迅速增大,1050℃时空洞的半径达1.10nm.     

Behavior of structure defects and hydrogen in neutron-irradiated stainless steels studied by positron annihilation method

Measurements of angular distributions of annihilation photons are applied to investigating structural defects and hydrogen behavior in annealed, plastically deformed, and irradiated stainless steels. It is determined that the whole cycle of investigations performed by positron diagnostics helped in tracing the formation and evolution of the defect structure and hydrogen behavior in different kinds of steels being subjected to complex physical–mechanical influences such as plastic deformation, hydrogenation and irradiation by fission neutrons. The high sensitivity of the electron–positron annihilation method allowed understanding even of details of the changes of the crystalline structure of multi-component materials.     

强流脉冲电子束作用下AISI 304L奥氏体不锈钢的微观结构与腐蚀性能

利用强流脉冲电子束(HCPEB)技术,对AISI 304L奥氏体不锈钢进行了表面辐照处理,详细考察了辐照前、后材料表面的微观结构和腐蚀性能。实验结果表明:经过HCPEB辐照后,材料表面的抗腐蚀性能有所改善;表面喷发形成熔坑实现清除夹杂物的净化作用,以及表面形成厚而致密的钝化膜可有效地阻碍点蚀,均是提高材料抗腐蚀性能不可忽视的因素。透射电子显微镜分析结果表明,HCPEB辐照材料表层时,诱发了大量的过饱和空位缺陷以及类型丰富且密度很高的线、面晶体缺陷,空位缺陷的凝聚形成了空位型位错圈和堆垛层错四面体等空位簇缺陷。这些缺陷有助于形成厚而致密的表面钝化膜,进而阻止阴离子穿过表面钝化膜,延迟腐蚀进程,提高受辐照材料的抗腐蚀性能。     

Deuterium transport and isotope effects in type 316L stainless steel at high temperatures for nuclear fusion and nuclear hydrogen technology applications

We present the first complete data set for the permeability, diffusivity, and solubility of both deuterium and hydrogen in 316L stainless steel (316L SS) obtained over a wide temperature range of 350–850 °C that accommodates both nuclear fusion and nuclear hydrogen technology applications. The deuterium results were also compared with the hydrogen results to estimate the isotope effect. The isotope effect ratio for diffusivity was different from the classical prediction. Furthermore, some of our results were compared with the results previously reported for 316 SS. Results and discussion are presented with an emphasis on the deuterium permeation and isotope effects.     

JRQ and JPA irradiated and annealed reactor pressure vessel steels studied by positron annihilation

The paper is focused on a comprehensive study of JRQ and JPA reactor pressure vessel steels from the positron annihilation lifetime spectroscopy (PALS) point of view. Based on our more than 20 years’ experience with characterization of irradiated reactor steels, we confirmed that defects after irradiation start to grow and/or merge into bigger clusters. Experimental results shown that JPA steel is more sensitive to the creation of irradiation-induced defects than JRQ steel. It is most probably due to high copper content (0.29?wt.% in JPA) and copper precipitation has a major impact on neutron-induced defect creation at the beginning of the irradiation. Based on current PALS results, no large vacancy clusters were formed during irradiation, which could cause dangerous embrittlement concerning operation safety of nuclear power plant. The combined PALS, small angle neutron scattering and atomic probe tomography studies support the model for JRQ and JPA steels describing the structure of irradiation-induced clusters as agglomerations of vacancy clusters (consisting of 2–6 vacancies each) and are separated from each other by a distribution of atoms.     

AISI 304L奥氏体不锈钢表面微孔结构的强流脉冲电子束快速制备与表征

 利用强流脉冲（HCPEB）电子束技术,对AISI 304L奥氏体不锈钢进行了辐照处理,并利用透射电子显微镜对HCPEB诱发的空位簇缺陷进行了表征。实验结果表明,HCPEB辐照金属可在辐照表层诱发大量的过饱和空位,并形成空位型位错圈和堆垛层错四面体（SFT）。利用金相显微镜、扫描电子显微镜和非接触式光学轮廓仪,对其表面形貌进行了详细的表征,发现电子束处理后的样品表面形成了高密度、弥散分布和尺寸细小的微孔,表面微孔是由于HCPEB轰击诱发的大量空位(簇)缺陷,以线或面等结构缺陷为路径,向表层迁移导致空位的累积而形成的。采用HCPEB技术,选择合适的材料和辐照工艺参数,可以成功地制备出表面多孔金属材料。