Macroporous polystyrene-supported quaternary ammonium salt catalysts for the addition of carbon dioxide to glycidyl methacrylate

In the present study, the synthesis of (2-oxo-1,3-dioxolan-4-yl)methyl methacrylate (DOMA) from carbon dioxide and glycidyl methacrylate (GMA) was investigated in a semi-batch reactor using macroporous polystyrene beads containing pendant quaternary ammonium salt catalysts. The catalysts were prepared by partial copolymerization of styrene (ST) and divinylbenzene (DVB) with isooctyl alcohol, and then by copolymerization with vinylbenzyl chloride (VBC). Quaternization of the pendant chloromethyl groups was carried out by using trialkylamines. The catalytic activity of the macroporous polymer was influenced by VBC and isooctyl alcohol concentration, and by the structure of trialkylamine. A kinetic study was also carried out to better understand the reaction steps. This revised version was published online in June 2006 with corrections to the Cover Date.     

Addition of Carbon Dioxide to Phenylglycidyl Ether Using Polymer-Supported Quaternary Ammonium Salt Catalysts

The synthesis of phenoxymethyl ethylene carbonate from carbon dioxide and phenyl glycidyl ether was investigated in a semi-batch reactor using crosslinked polystyrene beads containing pendant quaternary ammonium salts as catalysts. The catalysts were prepared by suspension copolymerization of styrene, divinylbenzene (DVB) and vinylbenzyl chloride (VBC), followed by quaternization using trialkylamines. The influence of VBC and DVB concentration, the structure of trialkylamine, and the type of solvent, on the catalytic behavior are discussed. A kinetic study was also carried out to better understand the reaction steps. This revised version was published online in June 2006 with corrections to the Cover Date.     

Preparation and spectroscopic characterization of surface‐enriched (with active sites) polymer‐supported phase‐transfer catalysts and their efficiency in organic addition reactions: A kinetic study

We prepared two batches of surface‐enriched (with active sites) polymer‐supported phase‐transfer catalysts (SE‐PSPTC) by fixing the crosslinking monomer divinylbenzene (DVB) at 2% (first batch) and 6% (second batch) through a free‐radical suspension copolymerization method with vinylbenzyl chloride (VBC; 25%) as a functionality and with styrene (St) as a supporting monomer, followed by the quaternization of the resulting terpolymer beads with triethylamine. The enrichment of the active sites on the surfaces of the beads was accomplished by a surface‐grafting technique through the delayed addition of the functional monomer (VBC) to the partially polymerized copolymer beads of poly(St/DVB). To bring the active sites fully onto the surfaces, we prepared six different types of terpolymer beads in each batch by varying the partial polymerization time (PPT) of St/DVB—0 h [0 VBC (conventional)], 3 h (3 VBC), 6 h (6 VBC), 9 h (9 VBC), 12 h (12 VBC), and 15 h (15 VBC)—and then gradually adding the functional monomer (VBC) to the partially polymerized poly(St/DVB) system. The resulting terpolymer beads, containing different concentrations of pendant benzyl chloride (? CH₂Cl) on the surface in each batch, underwent facile quaternization [? CH₂N⁺(C₂H₅)₃Cl^?] with an increase in the PPT of St/DVB and remained constant at 12 VBC and 15 VBC. To asses the superiority of the catalysts according to the surface enrichment of the active sites, particularly between conventional (0 VBC) catalysts and other PPT‐based SE‐PSPTCs, we characterized all the catalysts by estimating the chloride‐ion concentration, by using Fourier transform infrared (FTIR), scanning electron microscopy (SEM), EDAX, and ESCA, and by carrying out the dichlorocarbene addition to olefins. The chloride‐ion concentration by the Volhard method and the peak intensity of the C? N stretching absorbance concentration, that is, the quaternary onium group in the FTIR spectra of both batches, increased with the PPT of St/DVB in both batches of catalysts. In particular, the chloride concentration of a first‐batch catalyst of a representative mesh size (?120 + 140) had a twofold enhancement between the conventional catalyst (0 VBC; 1.88 m equiv g^?1) and 9 VBC/SE‐PSPTC (3.74 m equiv g^?1), although the same amount of the functional monomer was added in both preparations. These results showed the higher enrichment of the active site on the surface of 9 VBC, and the same trend was also maintained for second‐batch catalysts, regardless of the catalyst mesh size. SEM images of both batches showed that there was a higher concentration of nodules [due to the grafting of poly(VBC)] on the surfaces of the beads of 9 VBC/SE‐PSPTC and the aforementioned PPT catalysts than on the surfaces of the conventional catalysts (0 VBCs), which exhibited smooth surfaces (because of the simultaneous addition of all three monomers). This observation confirmed the enrichment of active sites on the surfaces. In the EDAX analysis, up to a depth of 0.5–1 μm, the surface chloride concentration increased from 0 VBC to 9 VBC/SE‐PSPTC and remained constant in 12 VBC and 15 VBC, first‐batch catalysts of a representative mesh size (?120 + 140). The same trend was also observed in second‐batch catalysts, indicating the enrichment of the onium group more on the surface in 9 VBC/SE‐PSPTCs. The ESCA analysis, to a depth of about 20–30Å, proved that the concentration of covalent chloride on the surface had increased from 0 VBC (15%) to 9 VBC/SE‐PSPTCs (29%) and remained constant thereafter in first‐batch catalyst; the trend was the same for second‐batch catalysts, also confirming the strong evidence of surface enrichment of the active sites. Similarly, the rate constants of different olefin addition reactions catalyzed by both batches of catalysts also increased from 0 VBC to 9 VBC and remained constant with 12 VBC and 15 VBC catalysts. The twofold increase of the rate constants, regardless of the olefins, for conventional catalysts to 9 VBC/SE‐PSPTCs confirmed the enrichment of the active sites on the surfaces. All these experimental observations proved that 50% of the active sites were successfully brought out from inside the poly(St/DVB) networks to the exterior surfaces, although same amount of VBC was added for the preparation of all the catalyst types. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 347–364, 2003     

Dispersion copolymerization of 2‐ethylhexyl methacrylate and vinylbenzyl chloride and functional group conversions in a fluorinated solvent using microwave heating

Conventional and microwave heating were compared for free radical dispersion polymerizations of crosslinked copolymers of 2‐ethylhexyl methacrylate, vinylbenzyl chloride (VBC), and fluoroalkyl methacryate monomers in the solvent nonafluorobutyl ethyl ether, and for the functional conversion of the VBC units of the copolymer particles with trimethylamine to quaternary ammonium chloride units. By conventional heating, all polymerizations produced foamy coagulated products consisting of primary spherical particles 1–2 μm in diameter. Microwave heating using poly(1H,1H‐dihydroperfluorooctyl acrylate) as a stabilizer gave faster polymerization and stable dispersions of discrete 1 μm particles. Microwave heating also gave faster reactions of the copolymers with trimethylamine to produce quaternary ammonium chloride functionalized colloidal particles. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3813–3819, 2008     

Branched fluoropolymer-Si hybrids via surface-initiated ATRP of pentafluorostyrene on hydrogen-terminated Si(100) surfaces

Linear, branched, and arborescent fluoropolymer-Si hybrids were prepared via surface-initiated atom transfer radical polymerization (ATRP) from the 4-vinylbenzyl chloride (VBC) inimer and ClSO(3)H-modified VBC that were immobilized on hydrogen-terminated Si(100), or Si-H, surfaces. The simple approach of UV-induced coupling of VBC with the Si-H surface provided a stable, Si-C bonded monolayer of "monofunctional" ATRP initiators (the Si-VBC surface). The aromatic rings of the Si-VBC surface were then sulfonated by ClSO(3)H to introduce sulfonyl chloride (-SO(2)Cl) groups and to give rise to a monolayer of "bifunctional" ATRP initiators. Kinetics study indicated that the chain growth of poly(pentafluorostyrene) from the functionalized silicon surfaces was consistent with a "controlled" or "living" process. The chemical composition and functionality of the silicon surface were tailored by the well-defined linear and branched fluoropolymer brushes. Atomic force microscopy images revealed that the surface-initiated ATRP of pentafluorostyrene (PFS) had proceeded uniformly on the Si-VBC surface to give rise to a dense and molecularly flat surface coverage of the linear brushes. The uniformity of surfaces with branched brushes was controlled by varying the feed ratio of the monomer and inimer (VBC in the present case). The living chain ends on the functionalized silicon surfaces were used as the macroinitiators for the synthesis of diblock copolymer brushes, consisting of the PFS and methyl methacrylate polymer blocks.     

Solid‐phase incorporation of gaseous carbon dioxide into oxirane‐containing copolymers

Carbon dioxide was incorporated into poly(glycidyl methacrylate‐co‐methyl methacrylate) by a solid‐phase reaction, which transformed the pendent oxirane moieties into cyclic carbonate moieties, with quaternary ammonium halide catalysts. The incorporation of carbon dioxide into the copolymer led to soluble carbonate‐containing polymers, whereas the incorporation of carbon dioxide into the glycidyl methacrylate homopolymer produced an insoluble product. The copolymer composition, reaction temperature, and catalyst amount affected the incorporation efficiency and the side reaction that caused crosslinking. Effective incorporation was achieved under the following reaction conditions: the glycidyl methacrylate content was less than approximately 50%, the temperature was greater than the glass‐transition temperature, and the catalyst concentration was 1.5–6 mol %. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3812–3817, 2004     

Soluble polymer-bound quaternary ammonium salts for the addition reaction of glycidyl methacrylate with carbon dioxide

Soluble polymeric catalysts containing benzyltrialkylammonium chloride moieties and styrene or N,N-dimethylacrylamide as a polar unit were prepared by copolymerization of vinylbenzyl chloride and the corresponding monomer, and then quaternization of the chloromethyl group by trialkylamines. The addition reaction of glycidyl methacrylate and carbon dioxide proceeded effectively using these polymer-supported quaternary ammonium salts. The catalytic activity was affected by the amount of vinylbenzyl chloride, type of reaction solvent, and the structure of trialkylammonium salt due to the balance between lipophilicity and steric hindrance of the pendant quaternary ammonium salt. A kinetic study was also carried out to better understand the reaction steps. Copyright © 2003 John Wiley & Sons, Ltd.     

Synthesis of photopolymers with pendant cyclic carbonate and cinnamic ester groups

Photopolymers with both pendant cyclic carbonate groups and cinnamic ester groups were synthesized by the addition reaction of poly(glycidyl methacryalte-co-styrene)[poly(GMA-co-AN)] with carbon dioxide and then with cinnamoyl chloride. Soluble quaternary ammonium salt catalysts showed good yield of cinnamoyl chloride addition to the glycidyl methacrylate groups. Quaternary salt catalysts of longer alkyl chain length and of more nucleophilic anion offered higher yield of cinnamoyl chloride addition. Photochemical reaction test showed that poly(CNMA-co-DOMA-co-St) had a good photosensitivity. This revised version was published online in June 2006 with corrections to the Cover Date.     

Heterogeneous initiators for the synthesis of polymer nanocomposites

Nanocomposites are obtained by the radical polymerization of styrene and methyl methacrylate on the surface of a dispersed filler containing chemisorbed compounds of quaternary ammonium, which catalyze decomposition of cumene hydroperoxide. The heterogeneous catalysts of hydroperoxide decomposition are obtained via the adsorption of cetyltrimethyl ammonium bromide and acetylcholine chloride on sodium montmorillonite, cellulose, and chitosan. The highest rate of the polymerization of both monomers is provided by the cellulose–cetyltrimethyl ammonium bromide catalyst. For a more hydrophilic methyl methacrylate, the rate of radical initiation is significantly lower at the same concentrations of the catalyst and hydroperoxide compared with hydrophobic styrene; however, the rate of polymerization is higher than for styrene because of a higher activity of methyl methacrylate in chain-propagation reactions. Relatively high rates of radical generation upon contact of cellulose–cetyltrimethyl ammonium bromide and cellulose–acetylcholine with hydroperoxides open the possibility to create cellulose-based disinfecting and medical materials.     

季鏻盐型三相相转移催化剂的制备及其化学结构与相转移催化活性的关系

 使用两种 ω-氯代酰氯 (氯乙酰氯与氯丁酰氯) 对交联聚苯乙烯微球 (CPS) 进行 Friedel-Crafts 酰基化反应,使用 1,4-二氯甲氧基丁烷对 CPS 微球进行氯甲基化反应, 分别将可交换的氯引入 CPS 微球表面, 制备了化学改性的 CPS 微球. 然后使用三苯基膦对改性微球进行季鏻化反应, 制备了间隔臂 (spacer arm) 长度不同的三种季鏻 (QP) 盐型三相相转移催化剂 QP-CPS. 考察了主要反应条件对制备过程的影响, 并以氯化苄与乙酸钠合成乙酸苄酯的反应体系作为三相相转移催化的模型体系, 初步考察了 QP-CPS 的相转移催化活性,探索了催化剂结构与相转移催化活性的关系. 结果表明, 季鏻盐的化学稳定性较差,在制备过程中需控制反应时间与温度, 且宜选用极性较高的溶剂. 季鏻盐型三相相转移催化剂 QP-CPS 对乙酸苄酯的合成具有较高的催化活性, 在液-固-液之间可有效地实现反应物种乙酸根的转移. 与季铵盐 (QN) 型三相相转移催化剂 QN-CPS 相比, 季鏻盐型三相相转移催化剂 QP-CPS 具有更高的相转移催化活性. 间隔臂越长, QP-CPS 的相转移催化活性越高, QP-CPS 的亲水和亲油性能对相转移催化活性也有很大的影响.     

Synthesis of aromatic polyesters using polymeric catalysts having quaternary ammonium salt groups

The preparation of polyester (PQ) and copolyester (PQ-DIOL) catalysts having quaternary ammonium groups was performed, and an aromatic polyester (PEA) was directly synthesized from isophthaloyl chloride and diphenolic acid by aqueous/organic interfacial polycondensation using these polymer catalysts. The yield and molecular weight of the polyester were affected by the structure of the pendant quaternary ammonium groups.     

Core‐shell functional nanospheres for oligonucleotide delivery. III. Stealth nanospheres

Polymethyl methacrylate‐based stealth and functional nanospheres, specifically designed for the reversible adsorption of oligonucleotides (ODN), were prepared by emulsion polymerization of methyl methacrylate in the presence of an ionic comonomer, namely a quaternary ammonium salt of 2‐(dimethylamino)ethyl methacrylate, and a nonionic comonomer, namely a poly(ethylene glycol) methacrylate. The nanosphere size is substantially affected by the amount of both the nonionic and ionic comonomers. By appropriately adjusting the concentrations of the ionic and nonionic comonomers, the quaternary ammonium group and PEG chain surface densities can be finely tuned. Accordingly, a great variety of core‐shell‐type nanospheres, able to bind ODN and to induce dysopsonic effect, can be obtained. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3347–3354, 2000     

Optimisation of polystyrene resin-supported Pt catalysts in room temperature, solvent-less, oct-l-ene hydrosilylation using methyldichlorosilane

Six precursor resins with systematic variation of porous parameters were prepared by suspension polymerisation using specific compositions of divinylbenzene, styrene vinylbenzyl chloride (VBC) and 2-ethylhexan-l-ol (a porogen). Surface areas from N(2) sorption and BET analysis were approximately 2-170 m(2)g-(1). The VBC content in each case was 38 mol% and these groups were aminated using the sodium salt of trimethylethylene diamine. Pt was introduced onto each resin at three different loadings (approximately 0.03, approximately 0.2 and approximately 0.4 mmol g-(1)) by appropriate manipulation of K(2)PtCl(6). The matrix of 18 resin-supported Pt complexes was then assessed for catalytic activity in the room temperature, solvent-less, hydrosilylation of oct-l-ene using methyldichlorosilane such that alkene: silane: Pt ratio was fixed at 2:1:1x10(-3). Though all the catalysts showed activity lower than that of homogeneous Speier s catalyst, most were sufficiently active to be potentially valuable heterogeneous catalysts in the laboratory, and indeed the plant. The most lightly loaded resins proved to be the least active. The remainder were recycled 5 times, and the best performers, the most highly loaded species, a further 5 times making 10 consecutive uses in all. A strong dependence on the porous structure of the resins was demonstrated with the activity rising systemically with the surface area. The two highest surface area highest loaded species displayed good activity even when used for the tenth time. The level of concurrent alkene isomerisation observed was very low throughout (<1%) making these heterogeneous species very selective as well as highly active. Overall the derived catalysts are excellent candidates for use in the research laboratory, and with further development could also be valuable in continuous processes.     

Biologically active polymers. V. Synthesis and antimicrobial activity of modified poly(glycidyl methacrylate‐co‐2‐hydroxyethyl methacrylate) derivatives with quaternary ammonium and phosphonium salts

Antimicrobial copolymers bearing quaternary ammonium and phosphonium salts based on a copolymer of glycidyl methacrylate and 2‐hydroxyethyl methacrylate were synthesized. Poly(glycidyl methacrylate‐co‐2‐hydroxyethyl methacrylate) was modified for the introduction of chloromethyl groups by its reaction with chloroacetyl chloride. The chloroacetylated copolymer was modified for the production of quaternary ammonium or phosphonium salts. The antimicrobial activity of the obtained copolymers was studied against gram‐negative bacteria (Escherichia coli, Pseudomonas aeruginosa, Shigella sp., and Salmonella typhae), gram‐positive bacteria (Bacillus subtilus and B. cereus), and the fungus Trichophyton rubrum by the cut‐plug method. The results showed that the three copolymers had high antimicrobial activity. A control experiment was carried out on the main polymer without ammonium or phosphonium groups. The copolymer bearing quaternary salt made from tributyl phosphine was the most effective copolymer against both gram‐negative and gram‐positive bacteria and the fungus T. rubrum. The diameters of the inhibition zones ranged between 20 and 60 mm after 24 h. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2384–2393, 2002     

硫酸氢季铵盐催化环氧化物和氮杂环丙烷的醇解反应

利用四丁基硫酸氢铵(TBAHS)和大孔树脂(D201型)支载的硫酸氢季铵盐(D201-HSO4), 分别催化环氧化合物或氮杂环丙烷与甲醇的开环反应, 以高产率得到β-甲氧基醇或β-甲氧基胺. 两种催化剂对该反应都很有效, 但大孔树脂支载的硫酸氢季铵盐(D201-HSO4)易于制备, 并可以重复使用.     

A hyper-cross-linked polystyrene with nano-pore structure

Chloromethylated polystyrene (CMPS) beads were prepared by suspension polymerization of vinylbenzyl chloride (VBC), divinylbenzene (DVB) and styrene (St) in the presence of porogen. The same feed volume ratio of DVB leads to similar cross-linking degree for all CMPS, but decreasing VBC content provided a progressively reduced content of chloromethyl groups in each CMPS. Hyper-cross-linked polystyrene (HCLPS) beads were obtained by post cross-linking reaction of CMPS in dichloroethane (DCE) containing Friedel-Crafts catalyst. The role of porogen and its influence on nano-pore structure of HCLPS were investigated. The results showed that different types of porogen had significant effect on the nano-pore structure of the final products, such as specific surface area, average pore size and total pore volume. Using the mixture of toluene and cyclohexanol as inner porogen can yield the highest specific surface area for HCLPS beads. Moreover, higher amount of VBC lead to greater specific surface area and total pore volume. It was therefore indicated that nano-pore structure of HCLPS can be controllably prepared via changing porogen type and VBC concentration. Finally, the unprecedented swelling capacity was found for the hyper-cross-linked species derived from different porogen types.     

Photopolymerization of vinyl monomers with quaternary ammonium salts

Photopolymerization of vinyl monomers with a series of quaternary ammonium salts has been investigated. However, quaternary ammonium salts used are not photosensitizers but rather photoinitiators. The salts photoinitiation activity was observed to vary widely with the counteranion in quaternary salts used and also with the alkyl group in their amine components. In general, the halide salts were more effective than tetrafluoroborate salts. It was also found that the overall activation energy for the photopolymerization of methyl methacrylate with dimethylbenzylanilinium tetrafluoroborate was 5.9 kcal/mole, and its rate was proportional to the 0.32 and 1.0 order of the concentration of the salt and the monomer used, respectively. An endgroup similar to dimethylaniline was found to be present in the methyl methacrylate polymer obtained by above system; this is probably a methylanilinomethyl group, from the characteristics of its ultraviolet spectrum.     

Synthesis of dimethyl carbonate and propylene glycol from transesterification of propylene carbonate and methanol using quaternary ammonium salt catalysts

Summary The synthesis of dimethyl carbonate (DMC) was investigated through the transesterification of propylene carbonate (PC) with methanol using quaternary ammonium salt catalysts. The reaction was carried out in an autoclave at 120-140 oC under carbon dioxide pressure of 250-400 psig. The main by-product was propylene glycol. The quaternary salts of larger alkyl group and more nucleophilic counter anion exhibited higher catalytic activity. Kinetic studies were also performed to better understand the reaction mechanism. Quaternary ammonium chlorides immobilized on polystyrene supports were also tested for their possible uses as heterogeneous catalysts.     

Polymer–silicate nanocomposites produced by in situ atom transfer radical polymerization

Polymer–silicate nanocomposites were synthesized with atom transfer radical polymerization (ATRP). An ATRP initiator, consisting of a quaternary ammonium salt moiety and a 2‐bromo‐2‐methyl propionate moiety, was intercalated into the interlayer spacings of the layered silicate. Subsequent ATRP of styrene, methyl methacrylate, or n‐butyl acrylate with Cu(I)X/N,N‐bis(2‐pyridiylmethyl) octadecylamine, Cu(I)X/N,N,N′,N′,N″‐pentamethyldiethylenetriamine, or Cu(I)X/1,1,4,7,10,10‐hexamethyltriethylenetetramine (X = Br or Cl) catalysts with the initiator‐modified silicate afforded homopolymers with predictable molecular weights and low polydispersities, both characteristics of living radical polymerization. The polystyrene nanocomposites contained both intercalated and exfoliated silicate structures, whereas the poly(methyl methacrylate) nanocomposites were significantly exfoliated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 916–924, 2004     

Dehydrochlorination of vinylidene chloride-vinyl chloride copolymer by aqueous sodium or potassium hydroxide solutions under two-phase conditions

The reaction of solid copolymer of vinylidene chloride and vinyl chloride with aqueous sodium or potassium hydroxide solutions in the presence of quaternary ammonium or phosphonium salts as phase transfer catalysts gave dehydrochlorinated products with chlorine-substituted polyene structure. Among the catalysts used tetrapropylammonium bromide was the best and potassium hydroxide was more active than sodium hydroxide. The activity of quaternary ammonium salts was discussed in terms of hydrophile–lipophile balance. The effects of temperature and the concentration of the bases and catalysts were investigated to obtain the optimum reaction condition. Treatment of the polymer films and solutions in tetrahydrofuran with aqueous bases under two-phase conditions also produced dehydrochlorinated films and powders.