Profiles of ethylene polymerization with zirconocene–trialkylaluminum/borane compound

Ethylene polymerization was conducted with bis(cyclopentadienyl)zirconium dichloride (1) and rac-dimethylsilylenebis(indenyl)zirconium dichloride (2) combined with trialkylaluminum (AlR₃; R=methyl (Me), ethyl (Et), isobutyl (iBu))/triphenylcarbenium tetrakis(pentafluorophenyl)borate (Ph₃CB(C₆F₅)₄) or tris(pentafluorophenyl)borane (B(C₆F₅)₃) to study the effect of cocatalysts on polymerization rate (R_p). When AlMe₃ was used, no activity or very low activity was observed with both zirconocenes regardless of the borane compounds used. The replacement of AlMe₃ to AlEt₃ or AliBu₃ with 1–AlR₃/Ph₃CB(C₆F₅)₄ caused polymerization and induction time was observed to reach the maximum R_p. Especially in the case of using AlEt₃, it took about 30 min to show the activity. When B(C₆F₅)₃ was used, AlEt₃ was not effective but AliBu₃ gave the highest activity among all the combinations of AlR₃ and the borane compounds. In the case of polymerization with 2 using Ph₃CB(C₆F₅)₄, high activity was observed with both AlEt₃ and AliBu₃ without any induction period. When B(C₆F₅)₃ was used instead of Ph₃CB(C₆F₅)₄, very low activity was observed with AlEt₃. On the other hand, high activity was observed with AliBu₃, and the maximum R_p was found at the beginning of the polymerization. The effect of AlR₃ on the formation of active species was discussed based on these results.     

M/(MgO)y(CeO2)1－y(M=Ni、Co、Cu)催化剂的催化甲烷燃烧性能

采用溶胶凝胶法制备了M/(MgO)_y(CeO2)_1－y(M=Ni、Co、Cu)催化剂. 研究了催化剂Ni/(MgO)y(CeO₂)_1－y催化活性与Ce含量的关系, 当y＝0.9时, 催化剂的活性和稳定性最好. 对比研究了(MgO)_0.9(CeO2)_0.1为载体, 负载Ni、Co、Cu活性组分的催化剂催化甲烷燃烧性能. 结果表明, 负载Cu的催化剂活性最好, 但二次评价后催化剂已烧结；负载Ni的催化剂活性与负载Cu的催化剂相差不大, 且稳定性最好, 经1000 ℃焙烧的Ni/(MgO)_0.9(CeO2)_0.1催化剂比表面仍有14.32 m₂•g^－1, 具有较高的催化活性和很好的热稳定性；负载Co的催化剂活性不如前两者, 稳定性居中, 但比表面降低得最少, 抗烧结能力强.     

恒温石墨炉中基体对钾和镉的影响

电热原子化原子吸收分析易受基体的干扰,使得准确度的提高受到限制.有关减少和消除这个影响已有报导^[1-6]。Czobik等^[6]人曾指出,为减少和消除基体的干扰,应设计一种具有时间和空间上等热条件的石墨炉。恒温石墨炉有上述的性质,用它作原子化器能消除和减少基体的影响。     

Measurements of HO2 uptake coefficient on aqueous (NH4)2SO4 aerosol using aerosol flow tube with LIF system

The γ(HO₂) was elevated with increase of Cu(II) concentrations in aqueous (NH₄)₂SO₄ aerosol. The threshold of Cu(II) concentration was 10^-3 mol/L for the dramatic increase of γ(HO₂) to 0.1, suggesting sensitive γ(HO₂) value to concentration of transition metal ions in aerosol.     

The effects of surface ligands and counter cations on the stability of anionic thiolated M12Ag32 （M=Au,Ag） nanoclusters

The stabilities of [M12Ag32（SR）30]4- （M = Ag, Au and SR = SPhF2, SPhCF3, SPhF） clusters having the same structure but different surface ligands or counter cations were systematically studied. It was clearly revealed that a subtle structural change in the surface ligands or counter cations could significantly alter the overall stability of [M12Ag32（SR）30]4 although they all had an electronic structure of 18-electron superatom shell closure. SPhF2 was found as a better surface ligand than SPhCF3 or SPhF to stabilize [M12Ag32（SR）30]4-. And the use of more bulky [（PPhj）2N]＋ as the counter cations was revealed to be more deleterious to the overall stability of [M12Ag32（SR）30]4- clusters than PPh4＋. [Au12Ag32（SR）30]4- was much more stable than [Ag44（SR）30]4 with the same surface ligands and counter cations. An exceptional stability was observed on （PPh4）4[Au12Ag32（SPhF2）30] which was stable in DMF for more than 8 days in air at 80 ℃. More research efforts are still needed to deeply understand why a small structural change could result in a significant change in the stability of noble metal nanoclusters.     

EXAFS/FT-IR characterization of tetra-iridium carbonyl clusters bound to tris-(hydroxymethyl)phosphine grafted silica surface catalytically active for propene oxidation to acetone

Structure and catalytic activity of Ir₄(CO)₁₂ bound to tris-(hydroxymethyl)phosphine (THP) grafted silica (THP/SiO₂) was investigated by means of EXAFS, FT-IR and kinetic studies. It was found that Ir₄(CO)₁₂ was uniformly attached on THP/SiO₂ by substitution of CO by THP (Ir₄/THP/SiO₂). The tetra-iridium carbonyl cluster framework was remained during the substitution of THP ligands and two THP ligands coordinated to the iridium carbonyl clusters to form Ir₄(CO)₁₀(THP/SiO₂)₂. species. When Ir₄/THP/SiO₂ was evacuated at 373 K, bridge CO was desorbed and Debye-Waller factor of Ir---Ir contribution derived from EXAFS analysis was increased which suggested that the cluster framework was distorted by the evacuation at 373 K. The resulting sample evacuated at 373 K was an active catalyst for hydroformylation of ethene and partial oxidation of propene, while the Ir₄/THP/SiO₂ without evacuation exhibited poor catalytic activities. The propene oxidation reaction proceed on the Ir₄/THP/SiO₂ evacuated at 323–353 K under subatmospheric pressures to give acetone as a product in high selectivity. The ethene hydroformylation proceed on the evacuated Ir₄/THP/SiO₂ at lower temperatures compared with other conventional iridium catalysts. EXAFS characterization and kinetic studies suggested that the catalytic activities were associated with the structural distortion of the iridium cluster framework due to surface attachment by the bidentate phosphine substitution.     

合成高产率的Au21(SR)15纳米簇

近年来,精确原子个数的金纳米簇因其在催化、生物医药、传感等领域具有潜在应用而备受关注。本研究中使用金刚烷硫醇(HS-Adam)作为配体制备了Au₂₃(S-Adam)₁₆纳米簇。在室温条件下,通过HS-Adam刻蚀Au₂₃(S-Adam)₁₆纳米簇,得到了纯度较高的Au₂₁(S-Adam)₁₅,其转换率可达20% (根据金原子计算)。并通过紫外可见吸收光谱(UV-Vis),电喷雾(ESI)和基质辅助激光解析飞行时间(MALDI)质谱以及热重分析(TGA)对合成的金纳米簇进行表征。     

抗烧结Rh-Sm_2O_3/SiO_2催化剂的制备和表征及其甲烷部分氧化制合成气性能

以乙酰丙酮铑(Rh(acac)_3)和乙酰丙酮钐(Sm(acac)_3)为前驱体,用浸渍法制备了Rh/SiO_2和Rh-Sm_2O_3/SiO_2催化剂。采用原位红外光谱、热重分析、低温N_2吸附、X射线粉末衍射、高分辨透射电子显微镜、H_2-程序升温还原和X射线光电子能谱等实验技术对催化剂的制备过程,比表面积和物相以及Rh与Sm_2O_3间的相互作用进行了表征,并以甲烷部分氧化制合成气为目标反应对催化剂的稳定性进行了考察。研究表明:以Rh(acac)_3和Sm(acac)_3为前驱体采用简单的浸渍法即可制备出Rh平均粒径为2.3 nm且具有良好抗烧结性能的Rh-Sm_2O_3/SiO_2催化剂。在浸渍过程中乙酰丙酮化合物通过与SiO_2表面羟基形成氢键而负载于载体表面。Sm(acac)_3在SiO_2表面的单层负载量(质量分数)约为31%,对应于Sm_2O_3的质量分数约为15%,只要Sm(acac)_3的质量分数低于这一阈值,均可保证分解后生成的Sm_2O_3以高分散形式负载于SiO_2上,且不会因高温(800°C)焙烧而团聚。高分散于SiO_2表面的Sm_2O_3与Rh之间存在强的相互作用,可显著提高Rh的分散度,防止其在高温反应条件下烧结,进而使低Rh负载量的催化剂表现出良好的甲烷部分氧化制合成气反应活性和稳定性。     

沉淀法制备Bi2O3的晶相转变过程及其光催化性能

以硝酸铋为原料,氨水为沉淀剂,通过液相沉淀法制得前驱体Bi(OH)₃,并将Bi(OH)₃分别在不同温度和时间下焙烧。利用X射线衍射(XRD)、拉曼光谱、热重(TG)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)及紫外-可见漫反射光谱(UV-Vis DRS)详细研究了Bi(OH)₃转变为Bi₂O₃的过程及相变过程中粒子形貌、大小、光吸收性质等。结果表明,前驱体Bi(OH)₃经过焙烧之后,发生了如下的转变过程:Bi(OH)₃→Bi₅O₇NO₃→β-Bi₂O₃/Bi₅O₇NO₃→β-Bi₂O₃/Bi₅O₇NO₃/α-Bi₂O₃→α-Bi₂O₃,而且转变过程伴随着粒子长大。在上述转变过程中,与Bi₅O₇NO₃向β-Bi₂O₃转变的过程相比,从β-Bi₂O₃到α-Bi₂O₃相变过程更为迅速。此外,以光催化降解罗丹明B(RhB)为模型反应,考察了不同晶相的Bi₂O₃光催化活性,结果表明Bi₅O₇NO₃和β-Bi₂O₃材料具有优异的光催化性能,而α-Bi₂O₃具有较低的光催化活性。     

理论空燃比天然气汽车尾气中H2O和O2对CH4与NO反应的影响

共沉淀法制备CeZrYLa+LaAl 复合氧化物载体, 等体积浸渍法制备了Pt 催化剂, 用于研究理论空燃比天然气汽车(NGVs)尾气净化反应中CH₄与NO的反应规律. 并考察了10% (体积分数, φ)H₂O和计量比O₂对CO₂存在时的CH₄+NO反应的影响. 结果表明: 对于不同条件下的NO+CH₄反应, 主要生成N₂和CO₂, 高温区有CO生成. 低温区无O₂时可以生成N₂O, 有O₂时可以生成NO₂; 添加10% (φ)的H₂O后, CH₄ 转化活性降低, NO转化活性基本不变, 这是由于H₂O减弱了CH₄与CO₂的重整反应, 但是对CH₄与NO的反应基本没有影响; 添加计量比的O₂后, CH₄转化活性提高, 而NO转化活性降低, 这是由于O₂和NO之间存在竞争吸附, CH₄被O₂氧化为主要反应, 从而减弱了NO的转化; 同时添加计量比的O₂和10% (φ) H₂O, CH₄与CO₂的重整反应受到抑制,CH₄与NO的反应、甲烷蒸汽重整反应和甲烷被O₂氧化反应同时发生, CH₄和NO的转化活性均提高.     

The nature of the surface site for isocyanate produced in the reaction of ammonia and carbon monoxide over supported catalysts

The reaction of CO and NH₃ was performed over M/X (M=Rh, Ru, Pd; X=Al₂O₃, SiO₂, TiO₂) films. Infrared spectroscopy was used to monitor the formation of surface intermediates. Isocyanate (NCO) was detected for all of the metals when the support was Al₂O₃ or SiO₂, but not for TiO₂. The NCO resided on the Al₂O₃ support for all M/Al₂O₃ catalysts, but on the metal when the support was SiO₂. It was concluded that the formation and location of the NCO was dependent upon the extent of NH₄⁺ formation on the various supports.     

利用硫酸氧钒制备钒炭催化剂用于烟气脱硫

利用硫酸氧钒制备钒炭催化剂用于烟气脱硫。研究发现,负载在活性炭上的硫酸氧钒极易被氧化为五价钒硫酸盐,这些五价钒硫酸盐具有很高的氧化SO₂的活性,极大地促进了SO₂在活性炭上的脱除。而且,通过煅烧可以将五价钒硫酸盐分解为五价钒氧化物,最佳煅烧温度为500℃,由于煅烧后用于储存硫酸的微孔孔容增加,SO₂的吸附容量得到了进一步提高,由此表明,利用硫酸氧钒可以制备传统的V₂O₅/AC催化剂。为了获得完全氧化的钒物种,对煅烧后的催化剂进行了空气中预氧化,但由于含氧官能团的形成、炭载体的烧蚀以及钒的还原,预氧化不利于脱硫。此外,研究中得到初步证据证明脱硫过程中V₂O₅/AC催化剂中五价钒氧化物转变成了五价钒硫酸盐,结合五价钒硫酸盐所表现出的氧化SO₂的能力,推测SO₂在V₂O₅/AC上的脱除遵循以下机理:五价钒氧化物先转变为五价钒硫酸盐,后者催化氧化SO₂为硫酸。     

THE ACTION MODE OF CISPLATIN ON DNA-SYNTHESIS AND CHARACTERIZATION OF N7 N1 CROSS-LINKAGE MODEL COMPOUND OF PLATINUM AND GUANOSINE

The title Pt-Guo compound was synthesized and isolated by the reaction between cis-[Pt(NH3)2(H2O)2](NO3)2 and guanosine of mol ratio1:1 in a neutral aqueous solution followed by careful purification with partial crystalization and recrystallizatlon from water at 0℃.The compound was characterized by elemental analysis,molecular weight determination,DTA,and C NMR spectroscopy and its formulawas found to be [8(GuoH-1)7 (OH)2] (NO3)7 8H2O.The isolation of the compound provides direct evidence for the intrastrand cross-linkage between cisplatin and DNA through N7,N1 atoms of two adjacent guanines.     

Surfactants having polyfluoroalkyl chains. II. Syntheses of anionic surfactants having two polyfluoroalkyl chains including a trifluoromethyl group at each tail and their flocculation-redispersion ability for dispersed magnetite particles in water

Anionic surfactants having two polyfluoroalkyl chains per molecule, i.e. the sodium salt of bis(1H, 1H, 2H,2H-heptadeca-fluorodecyl)-2-sulfosuccinate, CF₃(CF₂)₇(CH₂)₂OCOCH₂CH(SO₃Na)COO(CH₂)₂(CF₂)₇CF₃, the sodium salt of bis(1H, 1H, 2H, 2H-tridecafluoro-octyl)-2-sulfosuccinate, CF₃(CF₂)₅(CH₂)₂OCOCH₂CH(SO₃Na)COO(CH₂)₂(CF₂)₅CF₃, and the sodium salt of bis(1H, 1H, 2H, 2H-nonafluorohexyl)-2-sulfosuccinate, CF₃(CF₂)₃(CH₂)₂OCOCH₂CH(SO₃Na)COO(CH₂)₂(CF₂)₃CF₃, have been prepared from maleic anhydride, the corresponding alcohols possessing a polyfluoroalkyl chain and sodium hydrogen sulfite. The flocculation and redispersion abilities of these surfactants for dispersed magnetic particles in water have been examined to investigate the effect of the chain length. It was found that this ability was enhanced by an increase in the chain length. The contact angles for water for pelleted surface-modified magnetite have been measured. In order to compare this ability and the contact angles, data for other fluorinated surfactant have been obtained. The Kraff point, the surface tension and the pNa of the aqueous surfactant solutions have also been measured.     

金属有机骨架材料/聚酰亚胺混合基质膜的制备及气体分离性能

合成了3种不同结构、 粒径和气体吸附性能的金属有机骨架材料(MOFs): 微米级Cu₃(BTC)₂、 亚微米级ZIF-8和S-Cu₃(BTC)₂. 氮气吸附等温线分析结果表明, ZIF-8和Cu₃(BTC)₂具有较大比表面积(1653和1439 m²/g), S-Cu₃(BTC)₂的比表面积为171.4 m²/g. 用共混法将MOFs直接引入聚酰亚胺中制备了MOFs/聚酰亚胺混合基质膜(MMMs). X射线衍射(XRD)和全反射红外光谱(FTIR-ATR)分析结果表明, MOFs在混合基质膜中保持物理和化学稳定. 气体渗透测试结果表明, MOFs的加入使膜的气体渗透分离性能明显提高, S-Cu₃(BTC)₂使渗透系数增加了1.75倍; ZIF-8和Cu₃(BTC)₂使渗透系数增加了3倍左右; 同时, 膜的气体分离系数变化很小.     

Supported transition-metal catalysts for the C---C coupling reaction between ethene and diazoalkanes

The preparation of a series of immobilized transition-metal catalysts are reported. The catalysts were obtained by chemisorption of either rhodium(I) or iridium(I) complexes [MX(C₂H₄)₂]_n (M = Rh, Ir; X = Cl, OAc, acac, f₃-acac, f₆-acac) on SiO₂ or MgO supports. The oxides were also activated by SiCl₄ or TiCl₄ to give support materials in which the acidic nature of the surface is substantially increased. The activity of the immobilized catalysts was tested, particularly in the reaction of ethene with diphenyldiazomethane which yields a mixture of 1.1-diphenylpropene (8) and 1.1-diphenylcyclopropane (9). It was found that the most active and most selective (highest ratio 8:9) catalyst B1 was formed support material B (SiO₂ activated by SiCl₄) and [RhCl(C₂H₄)₂]₂ (1) and that both the activity and selectivity of B1 was comparable with that of complex 1 in solution. In contrast, the supported catalysts A2, D2 and A3, D3 obtained from [Rh(OAc)(C₂H₄)₂]₂ (2) and [Rh(acac)(C₂H₄)₂] (3) were less active than compounds 2 and 3 in solution. The immobilized catalysts A6, A7, D7 and E7, which were generated from the chloro- and acetatoiridium(I) complexes [IrCl(C₂H₄)₂]₂ (6) and [Ir(OAc)(C₂H₄)₂]₂ (7), possessed a lower activity than the rhodium counterparts. With diazoalkanes other than Ph₂CN₂, the activity of the supported catalyst B1 was partly higher and partly lower than that of complex 1 in the homogeneous phase.     

SnO_2/TiO_2纳米管复合光催化剂的性能及失活再生

基于微波水热法和微乳液法合成SnO2/TiO2纳米管复合光催化剂.通过X射线衍射(XRD)、配有能量色散X射线光谱仪(EDX)的透射电镜(TEM)和电化学手段对光催化剂进行表征.以甲苯为模型污染物,考察光催化剂在紫外光(UV)和真空远紫外光(VUV)下的性能及失活再生.结果表明,SnO2/TiO2纳米管复合光催化剂形成三元异质结(锐钛矿相TiO2(A-TiO2)/金红石相TiO2(R-TiO2)、A-TiO2/SnO2和R-TiO2/SnO2异质结),促使光生电子-空穴对的有效分离,提高光催化活性.SnO2/TiO2表现出最佳的光催化性能,UV和VUV条件下的甲苯降解率均达100%,CO2生成速率(k2)均为P25的3倍左右.但由于UV光照矿化能力不足,中间产物易在催化剂表面累积.随着UV光照时间的增加,SnO2/TiO2逐渐失活,20 h后k2由138.5 mg·m-3·h-1下降到76.1 mg·m-3·h-1.利用VUV再生失活的SnO2/TiO2,过程中产生的·OH、O2-·、O(1D)、O(3P)、O3等活性物质可氧化吸附于催化剂活性位的难降解中间产物,使催化剂得以再生,12 h后k2恢复到143.6 mg·m-3·h-1.UV和VUV的协同效应使UV降解耦合VUV再生成为一种可持续的光催化降解污染物模式.     

三丁基氧化膦-离子液体体系萃取UO2(NO3)2的机理和选择性

研究了三辛基氧化膦(TOPO)和三丁基氧化膦(TBPO)在离子液体(ILs) 1-烷基-3-甲基咪唑双三氟甲基磺酰亚胺盐(C_nmimNTf₂, n=2, 4, 6, 8)中萃取分离UO₂(NO₃)₂. TOPO-C₂mimNTf₂和TOPO-C₄mimNTf₂体系萃取UO₂(NO₃)₂时会出现三相, 而TBPO萃取UO₂(NO₃)₂的萃合物可以很好地溶解在所有离子液体中. 论文也考察了萃取过程中的萃取剂浓度效应、酸效应、盐效应. 水相加入HNO₃会降低萃取效率. 盐效应证明了萃取是一种阳离子交换机理. 水相中加入NO₃^-能够提高U的萃取, 这说明NO₃^-参与萃取. 选择性研究表明: 除了在高酸度下对Zr 的显著萃取, TBPO-C₄mimNTf₂萃取体系在低酸度下对U呈现较好的选择性; 去除U后, 在低酸度下该体系对三价Nd 仍保持较好的选择性. 通过定量比较离子液体中NO₃^-进入量, 电喷雾质谱(ESI-MS)和紫外光谱表征确定了TBPO-C_nmimNTf₂中萃取机理的差异性. 萃取中存在两种萃合物, 即UO₂(TBPO)₃(NO₃)⁺和UO₂(TBPO)₃²⁺, 其中UO₂(TBPO)₃(NO₃)⁺的比例从C₂mimNTf₂体系到C₈mimNTf₂体系逐渐增加.     

A new route to complexes containing the tetracarbon (C4) ligand

Pyrolysis of a solution of {Ru₃(CO)₁₁}₂(μ-bdpp) (bdpp = bis(diphenylphosphino)butadiyne) yielded the complex {Ru₃(μ-PPh₂)(CO)₉}₂(μ₆-C₄), which contains a μ₆-C₄ ligand symmetrically bridging two Ru₃(μ-PPh₂)(CO)₉ clusters. When the complex {Fe(CO)₄}₂(μ-bdpp) was heated in the presence of Fe₂(CO)₉ another example of a C₄ complex, {Fe₂(μ-PPh₂)(CO)₆}₂(μ-C₄), was obtained. Both complexes were characterised by X-ray structure determinations; the C₄ ligand behaves as a buta-1,3-diyne-1,4-diyl system.     

Contradictory effect of gold nanoparticle-decorated molybdenum sulfide nanocomposites on amyloid-β-40 aggregation

The effect of gold nanoparticle-decorated molybdenum sulfide (AuNP-MoS₂) nanocomposites on amyloid-β-40 (Aβ₄₀) aggregation was investigated. The interesting discovery was that the effect of AuNP-MoS₂ nanocomposites on Aβ₄₀ aggregation was contradictory. Low concentration of AuNP-MoS₂ nanocomposites could enhance the nucleus formation of Aβ₄₀ peptides and accelerate Aβ₄₀ fibrils aggregation. However, although high concentration of AuNP-MoS₂ nanocomposites could enhance the nucleus formation of Aβ₄₀ peptides, it eventually inhibited Aβ₄₀ aggregation process. It might be attributed to the interaction between AuNP-MoS₂ nanocomposites and Aβ₄₀ peptides. For low concentration of AuNP-MoS₂ nanocomposites, it was acted as nuclei, resulting in the acceleration of the nucleation process. However, the structural flexibility of Aβ₄₀ peptides was limited as the concentration of AuNP-MoS₂ nanocomposites was increased, resulting in the inhibition of Aβ₄₀ aggregation. These findings suggested that AuNP-MoS₂ nanocomposites might have a great potential to design new multifunctional material for future treatment of amyloid-related diseases.