利用谐波光谱的伴线结构测量自生磁场

在飞秒激光与固体靶相互作用中,利用OMA光学多道分析谱仪,在靶前表面激光镜反方向测量了激光的二次谐波(2ω₀)光谱和三次谐波(3ω₀)光谱,观测到了红移的2ω₀光谱和3ω₀光谱的伴线结构。在激光功率密度为～1018 W·cm-2的条件下,通过2ω₀和3ω₀谐波光谱的伴线结构,回推出激光与等离子体相互作用中产生的自生磁场均小于1 MGs。随着激光功率密度的增大,谐波谱红移峰向长波方向移动,光谱同时发生展宽。分析认为,等离子体临界面的迅速膨胀是导致二次谐波和三次谐波红移的主要原因。随着预脉冲功率密度的增大,临界面膨胀速度增大,导致了谐波光谱峰更大的红移。自生磁场的测量为诊断临界面的运动方向和速度提供了新的依据。     

W波段二次谐波回旋行波管放大器的模拟与设计

回旋行波管放大器是一种具有高功率、高频率、宽带宽的毫米波放大器，TE₀₂模二次谐波回旋行波管放大器在保持基波回旋行波管放大器的基础上极大地减小了工作磁场,从而具有广阔的应用前景. 利用两段分布式损耗的互作用结构，有效抑制了绝对不稳定性和回旋返波振荡,避免了模式互作用电路引起的模式畸变，提高了输出功率，在一定程度上克服了谐波互作用较弱的缺点，满足了扩展功率容量和放大器长时间稳定工作的要求. 非线性模拟结果和粒子模型(particle in cell)模拟结果均表明，在工作电压为100k 关键词： W波段 二次谐波 回旋行波管放大器     

PS/Ag球壳阵列中高Q值等离激元腔模式的激发效率研究

从理论上系统地研究了聚苯乙烯(PS)/Ag球壳阵列中银球壳的形状(球形和椭球形)和完整度(侧壁有无开口)对多阶窄线宽等离激元腔模式激发效率的影响。理论上发现，在完整的球形银壳层阵列中，基于电的等离激元腔模式(TM₂和TM₃)能够被高效激发，而基于磁的等离激元腔模式(TE₁)激发效率则非常低。通过单独地将银球壳改变为椭球形状或单独在银球壳侧壁赤道上对称构建6个小开口均能有效增大TE₁模式的激发效率。尤其是，存在一个最佳的开口(20°)可使得TE₁模式的激发效率达到最大。理论上进一步发现，TM₂、TE₁和TM₃等离激元腔模式在非完整(侧壁开口约为20°)的椭球形银壳层阵列结构中均能够同时被高效激发。在实验上，利用自支撑技术成功地制备了侧壁带有开口(约为20°)的椭球形银壳层阵列结构，实验测试的透射光谱与理论光谱非常吻合，很好地证实了理论预测结果的正确性。     

高功率微波在等离子体填充波导中的谐波产生

采用等离子体流体理论，研究了高功率微波在等离子体填充波导中的谐波产生，导出了非线性波动方程. 对二次谐波产生进行了数值计算与分析. 理论分析和数值计算表明，高功率微波将在等离子体填充波导中激发起谐波，TE_0n模式与TM_0n模式的基波都将激发起TM类型的谐波. 关键词： 高功率微波 谐波产生 等离子体填充波导     

连续调谐太赫兹回旋管非稳定振荡状态研究

太赫兹回旋管可实现高功率输出,并具有一定的频率调谐范围,是核磁共振波谱系统理想的高功率太赫兹辐射源。设计了263 GHz,TE_5,2基波连续调谐回旋管,通过磁场调节实现频率调谐范围为1.39 GHz,利用时域多模多频自洽非线性理论对设计的连续调谐回旋管非稳定振荡状态进行了研究。结果表明,在低次纵向谐波模式工作磁场范围内,当工作电流大于起振电流时,连续调谐回旋管先进入稳定状态,高次纵向谐波模式被抑制,工作模式TE_5,2的输出功率随时间不变;当电流增大,纵向谐波模式间的竞争引起回旋管由稳定状态进入到非稳定振荡状态,工作模式TE_5,2的输出功率随时间呈振荡变化且互作用效率大大降低;随着电流的进一步增大,回旋管又回到与低电流不同的稳定状态,互作用效率进一步降低。同时发现非稳定振荡状态的起始电流随着磁场增加而增大。本研究对需工作于稳定状态的面向DNP-NMR应用的连续调谐太赫兹回旋管的研制具有一定指导意义。     

BeH，BeD，BeT分子基态(X2Σ+)的结构与势能函数

采用量子力学从头算方法，运用二次组态相互作用QCISD(T)/aug-cc-pVTZ和电子相关单双耦合簇CCSD(T)/6-311++G(3df，2pd)研究了BeH，BeD，BeT分子基态的结构与势能函数，计算出了这些分子的光谱数据(ω_e，ω_eχ_e，B_e，α_e，D_e)，结果与实验光谱数据吻合较好.这表明上述分子基态的势能函数可用经修正的Murrell-Sorbie+c₆函数来表示. 关键词： BeH BeD BeT分子基态 分子结构 势能函数     

激光等离子体中3/2ω0谐波的实验观测

测量了激光产生的等离子体中3/2ω₀谐波的发射。结果表明,在靶面功率密度为10¹⁴W/cm²量级的情况下,3/2ω₀谐波发生蓝移,蓝移量约为70?。谐波本身加宽量为26?,随靶面功率密度增加,加宽量亦略有增大。 关键词：     

OH分子基态（X2Π）的结构与势能函数

采用密度泛函理论的B3LYP方法和二次组态相互作用(QCISD(T))方法优化计算了OH分子基态(X²Π)的平衡结构、振动频率和离解能.根据原子分子反应静力学原理，导出了OH分子基态(X²Π)的合理离解极限，采用最小二乘法拟合Murrell-Sorbie函数得到了相应的势能函数和与该基态相对应的光谱常数(B_e，α_e，ω_e和ω_eχ_e)，计算结果与实验数据符合得相当好. 关键词： OH分子 2Π)')" href="#">基态(X²Π) 势能函数     

NFX(X=-1,0,+1)分子离子基态的结构与势能函数

用密度泛函理论的B3LYP方法,分别以6-311++g(df,3pd),6-311g(3d,3p)和6-311++g(3df,3pd)为基函数对NF分子、NF⁺和NF^-离子基态进行几何优化和频率计算,并进行单点能扫描计算.用最小二乘法拟合得到NF^X(X=-1,0,+1)分子离子基态的Murrell-Sorbie势能函数.利用得到的解析势能函数计算出的NF分子和NF⁺离子基态光谱常数(B_e,α_e,ω_e,ω_eχ_e)与实验值符合很好.首次得到NF^-离子基态的光谱常数(B_e,α_e,ω_e,ω_eχ_e)和力常数(f₂,f₃,f₄),为NF-离子基态的后期研究提供理论参考.     

激光等离子体二次谐波时间分辨光谱的细结构

本文报道沿与光轴成90°方向拍摄的2ω₀谐波时间分辨光谱。谐波的主峰与次峰是由许多细而亮的条纹组成,对此我们作了理论分析。 关键词：     

Phase-matched second harmonic blue light generation in ion implanted KNbO3 planar waveguides with 29% conversion efficiency

We report for the first time to our knowledge, noncritical phase-matched second harmonic generation in an ion-implanted KNbO₃ planar waveguide. The guided TM₀ mode of the fundamental wave (868 nm) is converted into the second harmonic TE₁ mode (434 nm). From 1.3 kW of internal fundamental peak power 385 W second harmonic blue light is generated giving a conversion efficiency of 29%. A comparison of the measured and the theoretical efficiencies implies that phase-matching is achieved over the full waveguide length. Based on these first experimental results we estimate that 100 mW of blue light can be generated from 400 mW of input power using an optimized KNbO₃ planar waveguide of 1 cm length.     

Multimegawatt relativistic harmonic gyrotron traveling-wave tubeamplifier experiments

The first multimegawatt (4 MW, η=8%) harmonic (ω=sΩ_c, s=2,3) relativistic gyrotron traveling-wave tube (gyro-twt) amplifier experiment has been designed, built, and tested. Results from this experimental setup, including the first ever reported third-harmonic gyro-twt results, are presented. Operation frequency is 17.1 GHz. Detailed phase measurements are also presented. The electron beam source is SNOMAD-II, a solid-state nonlinear magnetic accelerator driver with nominal parameters of 400 kV and 350 A. The flat-top pulsewidth is 30 ns. The electron beam is focused using a Pierce geometry and then imparted with transverse momentum using a bifilar helical wiggler magnet. The imparted beam pitch is a α≡β_⊥/β_∥≈1. Experimental operation involving both a second-harmonic interaction with the TE₂₁ mode and a third-harmonic interaction with the TE ₃₁ mode, both at 17 GHz, has been characterized. The third-harmonic interaction resulted in 4-MW output power and 50-dB single-pass gain, with an efficiency of up to ~8% (for 115-A beam current). The best measured phase stability of the TE₃₁ amplified pulse was ±10° over a 9-ns period. The phase stability was limited because the maximum RF power was attained when operating far from wiggler resonance. The second harmonic, TE₂₁ had a peak amplified power of 2 MW corresponding to 40 dB single-pass gain and 4% efficiency. The second-harmonic interaction showed stronger superradiant emission than the third-harmonic interaction. Characterizations of the second- and third-harmonic gyro-twt experiments presented here include measurement of far-field radiation patterns, gain and phase versus interaction length, phase stability, and output power versus input power     

Study of high-power Ka-band second-harmonic gyroklystron amplifier

The self-consistent nonlinear theory of two-cavity high-harmonic gyroklystron amplifier has been developed. The efficiency and gain of a second-harmonic gyroklystron were calculated numerically. The results obtained were used to choose the optimal parameters of the experimental second-harmonic tube. The experimental study was carried out to test high-harmonic amplifier concept. Two-cavity 35 GHz second harmonic gyroklystron with the TE₀₂₁ cavity mode has been designed and tested in pulse operation. Output power of about 260 kW with efficiency 18% and 17 dB gain have been produced at 72 kV beam voltage and 20 A beam current. Bandwidth of about 0.1% has been observed. The restriction of the output power, efficiency, and gain was caused by spurious oscillations excited in the second cavity in the TE₀₁₁ mode at the fundamental cyclotron frequency     

Design and experimental operation of a 165-GHz, 1.5-MW,coaxial-cavity gyrotron with axial RF output

The development of a coaxial-cavity gyrotron operating in TE_31,17 mode at 165 GHz is presented. The selection of the operating frequency and mode are based on the limitations imposed by the maximum held of the superconducting (sc) magnet at Forschungzentrum Karlsruhe, Institut fur Technische Physik (FZK), the use of the inverse-magnetron injection gun (IMIG) of the 140-GHz, TE_28,16 coaxial gyrotron and the possibility of transforming the cavity mode to a whispering gallery mode (WGM) appropriate for the dual-beam quasioptical (q.o.) output coupler and the two output windows, which are foreseen for the next lateral output version of the tube. The tube with axial output has been tested at FZK to deliver maximum output power of 1.17 MW in the designed TE_31,17 mode with 26.7% efficiency at 164.98 GHz. Maximum efficiency of 28.2% was achieved at 0.9-MW output power. The design operating point with output power 1.36 MW and 36.7% efficiency was net accessible because of beam instabilities at high electron-velocity ratio α, presumably caused due to high electron-velocity spread. Power at higher frequencies was also detected: 1.02 MW at 167.16 GHz in TE_32,17 mode with 26.88 efficiency, 0.63 MW at 169.46 GHz in TE_33,17 mode with 18% efficiency, and 0.35 MW at 171.80 GHz in TE_31,17 mode with 13.3% efficiency     

用八孔耦合器识别TM0_(1)/TE_(11)混模中TE_(11)模式的方法北大核心CSCD

在高功率微波传输系统中,为了提高功率容量和效率,往往采用过模波导,因此圆波导中往往出现TM_(01)和TE_(11)混合模式的情况。采用角向均匀分布的8孔圆波导耦合器,对提取TE_(11)模式的混合比和极化角度的方法进行了分析和研究。分析了圆波导中TM_(01)和TE_(11)模式在耦合孔处的电场分布,并采用CST对各耦合孔的输出功率进行了模拟计算,得出相互正对的耦合孔的平均功率与8个孔的平均功率之比与模式之间的相位差无关的结论。同时,发现该比值与TE_(11)模式的混合比成线性关系,线性关系中的比例系数是极化角度线性函数。通过线性拟合获得了计算TE_(11)模式混合比和极化方向的表达式。与仿真设定的参数相比,用该表达式计算的结果表明,在TE_(11)模式混合比小于30%时,用其计算TE_(11)模式的混合比和极化角度是可行的,误差不超过10%。在此基础上,给出了实际情况下TE_(11)模式信息的具体判断方法。     

基于波导模式变换的圆波导TE62模式激励器的研究

基于不规则波导模式匹配法以及缓变波导中电磁波模式耦合理论,研究了一种W波段圆波导TE₆₂模式激励器. 该波导模式激励器采用矩形波导TE₁₀模式通过侧壁耦合馈入同轴波导,利用同轴波导的选模特性激励TE₆₁模式;随后利用轴向半径周期微扰的圆波导实现TE₆₁–TE₆₂模式变换. 文中推导了矩形-同轴波导模式匹配理论,系统研究了波导结构缓变参数对模式变换效率的影响,完成了模式变换器的优化仿真设计,数值计算结果表明：中心频率处TE₆₂模式的转换效率为94.5%,纯度为98.16%,效率85%以上带宽达到1 GHz,能够满足回旋管冷测的要求. 关键词： 同轴波导 模式变换 耦合模理论 半径微扰     

圆波导TE01模激励器设计及实验研究

对比分析了几种可输出圆波导TE₀₁模激励器的仿真设计结果。结果表明,利用行波功分结构实现矩形波导TE₁₀模到4路矩形波导TE₁₀模的等幅同相功分,进而合成转换成圆波导TE₀₁模的转换过程,可在较宽的频带范围内,实现圆波导TE₀₁模的高效激励。以中心频率9.40 GHz仿真设计的圆波导TE₀₁模激励器,在中心频率上的传输效率超过99.9%;在9.08~9.61 GHz的频率范围内,传输效率大于99%。实验测量结果表明,所加工激励器在较宽的频带范围内,传输损耗优于-0.2 dB,与仿真结果的差异主要来自于波导壁面的欧姆损耗和波同转换结构;器件工作频带内平坦特性良好,有利于开展测量工作。     

Special complex open-cavity and low-magnetic-field high-powergyrotron

A theory is proposed for the special complex cavity; it is in the form of a single resonant circuit having a TE_0n&lrarr2;TE_0,n+p mode converter and it features excellent mode selectivity, high power capability, and an asymmetric triangle profile of the RF field that is favourable to efficient operation for a 35-GHz second-harmonic gyromonotron employing this complex cavity with TE₀₃ mode output are numerically illustrated and experimentally demonstrated. Power as high as 200 kW and efficiency as high as 30% have been obtained. These experimental results are record values for a gyrotron operating at the second-harmonic millimeter wavelength. Implications of the single-resonant complex cavity for the fundamental harmonic and third-harmonic high-average-power gyrotron design are discussed     

X波段高功率宽带选模定向耦合器

过模圆波导在提高功率容量的同时,不可避免地会造成微波源中同时存在多种模式。为了监测X波段长脉冲高功率微波源TM₀₁模的输出功率和频谱,采用CST软件仿真设计了X波段高功率宽带选模定向耦合器,在耦合TM₀₁模的同时可实现对TM₀₂和TE₁₁模的抑制。波导腔体及耦合孔的尺寸以小孔耦合理论和相位叠加原理为基础并结合切比雪夫分布函数计算确定。仿真结果表明:该高功率宽带选模定向耦合器在9.0~9.8 GHz的带宽范围内,耦合度为(-59.08±1) dB,定向性大于30 dB,对TE₁₁模的抑制度大于15 dB,对TM₀₂模的抑制度大于30 dB,功率容量大于2.5 GW。     

Polarization control of microwave emission from high powerrectangular cross-section gyrotron devices

Results are summarized of experiments on a gyrotron utilizing a rectangular-cross-section (RCS) cavity region. The major issue under investigation is polarization control of microwave emission as a function of magnetic field. The electron beam driver is the Michigan Electron Long Beam Accelerator (MELBA) at parameters: V=0.8 MV, I_diode=1-10 kA, I_tube=0.1=0.5 kA, and t_e-beam=0.4-1.0 μs. The annular e-beam is spun up into an axis-encircling beam by passing it through a magnetic cusp prior to entering the RCS interaction cavity. Experimental results show a high degree of polarization in either of two orthogonal modes as a function of cavity fields. The RCS gyrotron produced peak powers of 14 MW in one polarization (TE₁₀) and 6 MW in the cross-polarized mode (TE ₀₁). Electronic efficiencies for this device reached as high as 8% with transverse efficiency of 16%. Experimental results on the beam alpha (α=V_⊥/V_∥) diagnostics, where alpha is the ratio of the e-beam's transverse velocity to its parallel velocity, agree well with the single electron trajectory code. MAGIC code results are in qualitative agreement with microwave measurements. Microwave emission shifts from the dominant fundamental mode polarization (TE₁₀□ ), to the next higher order mode polarization (TE₀₁□) as the solenoid magnetic field is raised from 1.4-1.9 kGauss. Frequency measurements using heterodyne mixers support mode identification as well as MAGIC code simulations